This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided to ensure safe disassembly and assembly of parts under spring force. The document also provides instructions for installing the rocker shaft assembly and adjusting valve lash clearances.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...orrf0370383
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...rishang96299
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...kubei069369925
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fuusejkddmmd3e
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...orrf0370383
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...rishang96299
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...kubei069369925
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fuusejkddmmd3e
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...dkdmidkkdk
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating with oil.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
4) Procedures for removing a cylinder head by draining fluids, disconnecting hoses and sensors, and removing bolts and
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...dujkdksmdmdm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jdksmmdmdd
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fujkse9didkke3
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
4) Procedures for removing a cylinder head such as draining fluids, removing hoses and wires, and loosening bolts.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fjkdksmmdm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...dkdmidkkdk
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjskekmsemm
The document provides instructions for removing and assembling the rocker shaft and related components of a Caterpillar 3054E engine. It describes in detail:
1) How to disassemble the rocker shaft assembly by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) The assembly procedure, including cleaning, inspecting, lubricating parts, and installing components in the proper order and orientation.
3) Instructions for installing the rocker shaft and pushrods, including applying lubricant, positioning parts correctly, tightening fasteners, and adjusting valve lash.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing associated components like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and guide bolts are used to position the cylinder head. Cylinder head bolts are then lubricated, installed, and tightened in sequential order.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is positioned and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools like guide bolts and a torque wrench are required to correctly perform the work.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and the head is positioned using guide bolts before reinstalling the bolts and tightening them in stages.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is lifted into place, and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools including guide bolts and a torque wrench are required to correctly perform the work.
1. The document provides instructions for removing the cylinder head from a Caterpillar 416F backhoe loader.
2. The procedure involves first draining the coolant and engine oil.
3. Key steps include removing accessories like the valve mechanism cover, loosening cylinder head bolts in a specific sequence, and then removing the cylinder head.
The document provides instructions for removing the cylinder head from a 416F Backhoe Loader engine. Key steps include draining coolant and oil, removing related components like the fuel injectors and exhaust manifold, and then loosening and removing bolts to lift the cylinder head off the cylinder block using a lifting device. The cylinder head gasket is also removed and discarded.
The document provides instructions for removing the cylinder head from a 416F Backhoe Loader engine. Key steps include draining coolant and oil, removing related components like the fuel injectors and exhaust manifold, and then loosening and removing bolts to lift the cylinder head off the cylinder block using a lifting device. The cylinder head gasket is also removed and discarded.
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
More Related Content
Similar to Caterpillar Cat 315C Excavator (Prefix ANF) Service Repair Manual (ANF00001 and up).pdf
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...dkdmidkkdk
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating with oil.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
4) Procedures for removing a cylinder head by draining fluids, disconnecting hoses and sensors, and removing bolts and
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...dujkdksmdmdm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jdksmmdmdd
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fujkse9didkke3
The document provides instructions for removing and assembling the rocker shaft and related components of an excavator engine. It describes:
1) Disassembling the rocker shaft by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) Assembling the rocker shaft by cleaning components, installing springs, rocker arms, washers and retaining rings, and lubricating.
3) Installing the rocker shaft and pushrods by applying oil, positioning components, tightening screws, and adjusting valve lash.
4) Procedures for removing a cylinder head such as draining fluids, removing hoses and wires, and loosening bolts.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...fjkdksmmdm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and inspect cylinder head bolts, lubricate the threads, and tighten the bolts in stages to the specified torques.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...dkdmidkkdk
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The key steps are:
1. Drain coolant and oil, disconnect hoses and wiring, and remove accessories from the cylinder head.
2. Gradually loosen and remove cylinder head bolts and lift off the cylinder head using a lifting device.
3. Clean the cylinder block and head mating surfaces, install a new gasket, and use guide bolts to position the cylinder head.
4. Clean and lubricate new cylinder head bolts, install in numerical order, and torque in two stages to the specified values.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjskekmsemm
The document provides instructions for removing and assembling the rocker shaft and related components of a Caterpillar 3054E engine. It describes in detail:
1) How to disassemble the rocker shaft assembly by removing retaining rings, washers, rocker arms, springs, and identifying the components.
2) The assembly procedure, including cleaning, inspecting, lubricating parts, and installing components in the proper order and orientation.
3) Instructions for installing the rocker shaft and pushrods, including applying lubricant, positioning parts correctly, tightening fasteners, and adjusting valve lash.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing associated components like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and guide bolts are used to position the cylinder head. Cylinder head bolts are then lubricated, installed, and tightened in sequential order.
Caterpillar cat 315 c excavator (prefix anf) service repair manual (anf00001 ...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is positioned and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools like guide bolts and a torque wrench are required to correctly perform the work.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjjsekkdmme
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels on the cylinder block and the head is positioned using guide bolts before reinstalling the bolts and tightening them in stages.
Caterpillar cat 315 c l excavator (prefix anf) service repair manual (anf0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054E engine. The removal process involves draining fluids, removing accessories like the exhaust manifold and fuel lines, and then loosening and removing cylinder head bolts. For installation, the cylinder head gasket is placed on dowels, the head is lifted into place, and bolts are lubricated, installed, and tightened in stages to the specified torques. Tools including guide bolts and a torque wrench are required to correctly perform the work.
1. The document provides instructions for removing the cylinder head from a Caterpillar 416F backhoe loader.
2. The procedure involves first draining the coolant and engine oil.
3. Key steps include removing accessories like the valve mechanism cover, loosening cylinder head bolts in a specific sequence, and then removing the cylinder head.
The document provides instructions for removing the cylinder head from a 416F Backhoe Loader engine. Key steps include draining coolant and oil, removing related components like the fuel injectors and exhaust manifold, and then loosening and removing bolts to lift the cylinder head off the cylinder block using a lifting device. The cylinder head gasket is also removed and discarded.
The document provides instructions for removing the cylinder head from a 416F Backhoe Loader engine. Key steps include draining coolant and oil, removing related components like the fuel injectors and exhaust manifold, and then loosening and removing bolts to lift the cylinder head off the cylinder block using a lifting device. The cylinder head gasket is also removed and discarded.
Similar to Caterpillar Cat 315C Excavator (Prefix ANF) Service Repair Manual (ANF00001 and up).pdf (20)
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
The document provides installation instructions for a swing gear and bearing on excavator models 320D2 and 320D2 L. It outlines 22 steps to assemble the swing drive, including installing bearings, seals, gears, housings and fasteners in the proper order. Tools and lubricants required for the installation are listed in a table. The process involves lifting and positioning heavy components weighing up to 280 kg.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1) The document provides instructions for installing a flywheel on a Caterpillar 320 GC excavator. It describes cleaning and preparing the crankshaft, installing guide studs and lifting the flywheel into place, then bolting it securely and checking the run out.
2) Additional steps are outlined for removing and installing the crankshaft rear seal and flywheel housing. The crankshaft rear seal is press-fit as a one-piece assembly and must be replaced if removed. Dowels, gaskets and seals are also installed during flywheel housing replacement.
3) Precise torques are specified for bolts depending on their grade, and alignment of the flywheel housing to the
Caterpillar Cat 318D2 L Excavator (Prefix HAH) Service Repair Manual (HAH0000...jse7039222
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents a step-by-step process involving 31 steps. Some key steps include fastening the final drive to a repair stand, removing bolts and washers to access internal components, and using various tools to separate parts like the carrier assembly, ring gears, planetary gears, and seals from the main housing. Proper cleaning and safety precautions are noted throughout.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and gives step-by-step instructions to remove components like the final drive cover, planetary assembly, retaining rings, and seals. It then describes the assembly process in reverse, including cleaning parts, replacing seals and O-rings, and torquing fasteners to the specified values. The goal is to repair or replace worn parts while maintaining cleanliness for proper functioning of the final drive.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Reassembly requires precisely installing seals, bearings, shims and other parts in the reverse order and verifying proper bearing preload using a press and micrometers. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing pieces. Reassembly requires precisely installing new seals and bearings then measuring clearance to determine the correct shim thickness before reinstalling all components in reverse order. Cleanliness and applying lubricant to parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. The disassembly process involves 28 steps to remove components like bolts, seals, springs, pistons, and bearings. The assembly process reverses the disassembly steps and includes precautions like cleaning parts, applying lubricant, and ensuring proper placement of springs, seals and other components. Tools required include link brackets, slide hammers, bearing pullers, drivers and turning tools.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...jse7039222
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The instructions emphasize cleanliness and using identification marks to ensure correct reinstallation of components.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jse7039222
This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided regarding spring force. The document also provides instructions for installing the rocker shaft and pushrods and adjusting valve lash clearance.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298103
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01150908
1. Remove the retaining ring (1) and remove the washer (2) from both ends of the rocker shaft
assembly.
Note: The rocker shaft (7) is not symmetrical as there is a machined flat (6) toward one end
of the shaft.
2. Place an identification mark on each of the components for installation. Ensure that you
note the component's relationship to the machined flat (6).
3. Remove the rocker arm assembly (3) for the inlet valve from the rocker shaft (7). Remove
the rocker arm assembly (4) for the exhaust valve from the rocker shaft (7).
4. Remove the spring (5) from the rocker shaft assembly.
5. Repeat Step 3 and Step 4 in order to completely disassemble the rocker shaft assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:04:47 UTC+0800 2020
2/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298104
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
Illustration 1 g01150908
Typical example
1/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Clean all of the components and inspect all of the components. Inspect the grooves for the
circlips (1) and ensure that all of the oil holes in the rocker shaft (7) and in the rocker arms
(3 and 4) are not plugged before you begin the assembly procedure. If necessary, replace
any worn components and any damaged components.
2. Check the clearance between the rocker shaft (7) and the bushing of every rocker arm (3 and
4). Refer to the Specifications Manual, "Rocker Shaft" or further information. If necessary,
replace any worn components.
3. Lubricate all of the components with clean engine oil before assembly.
Note: Ensure that the machined flat (6) on the rocker shaft (7) is facing upward.
4. Install a circlip (1) onto the end of the rocker shaft (7) that is closest to the machined flat
(6). Install a washer (2) onto the rocker shaft (7).
5. Install the rocker arm assembly (3) for the inlet valve onto the rocker shaft (7). Install the
rocker arm assembly (4) for the exhaust valve onto the rocker shaft (7).
6. Install the spring (5) onto the rocker shaft (7).
7. Repeat Step 5 and Step 6 in order to assemble the rocker shaft assembly.
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. Install the remaining washer (2) and the remaining circlip (1) onto the rocker shaft (7).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:05:43 UTC+0800 2020
2/2
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02298106
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6K-0806 Cable Strap 3
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00960356
Illustration 2 g00960345
1. Apply clean engine lubricating oil to both ends of the pushrods (6). Install the pushrods (6).
Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. If the rocker shaft was disassembled, install the Tooling (A) around the rocker arms (4) in
order to slightly compress spring (5). The rocker arms must be held away from the
machined face of the cylinder head (2) during reassembly.
3. Loosen the nut (8) and the adjustment screw (7) on each rocker arm. This will help prevent
a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Position the rocker shaft assembly on the cylinder head.
Note: The rocker shaft (3) of the rocker shaft assembly is not symmetrical. The rocker shaft
(3) has a machined flat at the front end of the shaft. Ensure that the machined flat is toward
the top and toward the front end of the engine.
5. Install the Torx screws (1) in the rocker shaft (3).
Note: The longest Torx screw must be installed at the front of the cylinder head in the hole
(X).
6. Ensure that the adjustment screws (7) are properly seated in the ends of the pushrods (6).
7. Alternately tighten the Torx screws (1). Start from the center and work toward the outside.
Tighten the Torx screws (1) to a torque of 35 N·m (26 lb ft).
8. Cut and remove the Tooling (A) from the rocker shaft assembly.
9. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Engine Valve Lash -
Inspect/Adjust" for more information on adjusting the valve lash.
End By:
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:06:39 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i01923525
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
c. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the engine oil cooler into a suitable container for storage or disposal.
Drain the engine oil from the engine oil cooler into a suitable container. Refer to Operation
and Maintenance Manual for the procedure on draining the engine coolant and the engine
oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the coolant
capacity and the engine oil capacity of the engine.
2. Loosen the hose clamp from the upper radiator hose and remove the upper radiator hose
from the water temperature regulator housing.
3. Disconnect the harness assembly from the bus bar for the glow plugs.
Illustration 1 g01001037
4. Disconnect the harness assembly from coolant temperature sensor (2).
5. Remove bolts (3). Remove bypass tube (4) from cylinder head (1). Remove the O-ring seals
from the bypass tube.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01000982
6. Gradually loosen cylinder head bolts (5) in reverse numerical order. Refer to Illustration 2.
This will help prevent distortion of the cylinder head.
7. Remove bolts (5) from cylinder head (1).
8. Use a suitable lifting device and carefully lift the cylinder head off the cylinder block. The
weight of the cylinder head is approximately 57 kg (126 lb).
Note: Do not use a lever to separate the cylinder head from the cylinder block.
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
9. Remove the cylinder head gasket.
Note: Note the location of the dowels on the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:07:35 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i05969946
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
C 5P-3975 Rubber Lubricant -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.
1/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01001065
1. Install the cylinder head gasket on dowels (6) on top of the cylinder block.
Note: Do Not use any sealant or compound on the cylinder head gasket.
2. Install Tooling (A) in the cylinder block.
3. Use a suitable lifting device to install the cylinder head. The weight of the cylinder head is
approximately 57 kg (126 lb).
Note: Ensure that the cylinder head is positioned on dowels (6) .
4. Remove Tooling (A) .
2/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00951563
5. Clean the threads of the cylinder head bolts. Inspect the cylinder head bolts.
Note: Do Not use bolts if there is any visual reduction in the diameter of the Threads (Y)
that has not been engaged with the cylinder block. Use a straight edge to check the bolts.
6. Lubricate the threads and the shoulder of the cylinder head bolts with clean engine oil
before installation.
Illustration 3 g03742524
7. Install bolts (5) on cylinder head (1) .
Note: The short bolts are installed in holes that are marked 1, 2, 3, 4, 5, 6, and 9.
Note: The long bolts are installed in holes that are marked 7, 8, and 10.
8. Tighten the cylinder head bolts in numerical order to a torque of 50 N·m (37 lb ft).
9. Tighten the cylinder head bolts in numerical order to a torque of 100 N·m (74 lb ft).
3/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00951562
10. Use Tooling (B) to achieve the correct final torque.
Note: If Tooling (B) is not used, place an index mark on each bolt.
11. Tighten the cylinder head bolts in numerical order.
a. Turn the short bolts (2, 5, 6, 7, 8, 9, and 10) for an additional 225 degrees.
b. Turn the long bolts (1, 3, and 4) for an additional 270 degrees.
Illustration 5 g01001037
4/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 12. Install new O-ring seals on bypass tube (4) . Apply Tooling (C) to the O-ring seals. Install
the bypass tube in cylinder head (1) . Install bolts (3) .
13. Connect the harness assembly to coolant temperature sensor (2) .
14. Connect the harness assembly to the bus bar for the glow plugs.
15. Install the upper radiator hose to the water temperature regulator housing.
16. Fill the cooling system with coolant. Fill the lubrication system with engine oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the cooling
system capacity and the lubrication system capacity of the engine.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
c. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:08:31 UTC+0800 2020
5/5
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02333592
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00540954
1. Use Tooling (A) to remove lifters (1).
Note: Place an identification mark on the lifters for installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the lifters with clean oil before installing the lifters in the cylinder block.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00540954
2. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are installed in the original location and that the lifters are
seated correctly.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:09:26 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02299051
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
b. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00951934
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Carefully remove camshaft (3) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior
to installation.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 1. Carefully install camshaft (3) in the cylinder block.
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 16:10:22 UTC+0800 2020
3/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR ANF
Configuration: 315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054E Engine for Caterpillar Built Machines
Media Number -RENR2411-03 Publication Date -01/05/2017 Date Updated -03/05/2017
i02299077
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
c. Remove the idler gear. Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01001848
1. Remove the setscrew (1) and the washer from the camshaft gear (2).
2. Remove the camshaft gear from the camshaft.
Note: Do not lose the key from the camshaft gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Make sure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing
and Adjusting, "Finding Top Center Position for No. 1 Piston".
2. Inspect the camshaft gear and the key for wear or damage.
3. Install the Tooling (A) through the camshaft gear. Install the Tooling (B) into the crankshaft
web.
2/3
315C L Excavator ANF00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP3...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...