This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fhsjejkdmem
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring and removing bolts securing the bypass tube.
3. Removing bolts securing the front housing and removing the front housing from the cylinder block.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fhsjejkdmem
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps, including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub, checking clearances, and tightening inserts on the rocker arms. The instructions conclude by stating to install the front cover and valve mechanism cover once the idler gear installation is complete.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjsekdmme
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub, checking clearances, and tightening inserts on the rocker arms. The instructions conclude by stating to install the front cover and valve mechanism cover once the idler gear installation is complete.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fjjsekdmme
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub while aligning timing marks, and checking specifications. The instructions conclude by installing covers once the idler gear is installed.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fjjskekdmmse
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It involves:
1. Ensuring the engine is in the correct timing position for installation.
2. Cleaning and inspecting the idler gear and hub before lubricating and installing them.
3. Aligning timing marks and installing retaining bolts while using various tools to hold components in place.
4. Checking clearances and backlash once installed before completing reassembly of covers.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It is a multi-step process that involves:
1. Ensuring the engine is in the correct timing position using timing pins.
2. Cleaning and inspecting old parts and installing new ones if needed.
3. Aligning timing marks and installing the idler gear assembly.
4. Checking clearances and backlash using gauges and making any needed adjustments.
5. Positioning the crankshaft and installing covers at the end of the procedure.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...tuzhiyou2
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It is a multi-step process that involves:
1. Ensuring the engine is in the correct timing position using timing pins.
2. Cleaning and inspecting the idler gear, hub, and plate before installation.
3. Lubricating and installing the hub, idler gear, and plate in the correct alignment and orientation.
4. Installing bolts and checking gear measurements and movement with gauges.
5. Returning the engine to a safe position before completing installation of covers.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fhsjejkdmem
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring and removing bolts securing the bypass tube.
3. Removing bolts securing the front housing and removing the front housing from the cylinder block.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fhsjejkdmem
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps, including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub, checking clearances, and tightening inserts on the rocker arms. The instructions conclude by stating to install the front cover and valve mechanism cover once the idler gear installation is complete.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjsekdmme
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub, checking clearances, and tightening inserts on the rocker arms. The instructions conclude by stating to install the front cover and valve mechanism cover once the idler gear installation is complete.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fjjsekdmme
This document provides instructions for removing and installing an idler gear on a Caterpillar C4.4 engine. It outlines 19 steps including using various tools to lock components in place, cleaning and inspecting parts, lubricating and installing the idler gear and hub while aligning timing marks, and checking specifications. The instructions conclude by installing covers once the idler gear is installed.
Caterpillar cat 313 f l excavator (prefix nlg) service repair manual (nlg0000...fjjskekdmmse
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It involves:
1. Ensuring the engine is in the correct timing position for installation.
2. Cleaning and inspecting the idler gear and hub before lubricating and installing them.
3. Aligning timing marks and installing retaining bolts while using various tools to hold components in place.
4. Checking clearances and backlash once installed before completing reassembly of covers.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It is a multi-step process that involves:
1. Ensuring the engine is in the correct timing position using timing pins.
2. Cleaning and inspecting old parts and installing new ones if needed.
3. Aligning timing marks and installing the idler gear assembly.
4. Checking clearances and backlash using gauges and making any needed adjustments.
5. Positioning the crankshaft and installing covers at the end of the procedure.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...tuzhiyou2
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It is a multi-step process that involves:
1. Ensuring the engine is in the correct timing position using timing pins.
2. Cleaning and inspecting the idler gear, hub, and plate before installation.
3. Lubricating and installing the hub, idler gear, and plate in the correct alignment and orientation.
4. Installing bolts and checking gear measurements and movement with gauges.
5. Returning the engine to a safe position before completing installation of covers.
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...jse7039222
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...lituo39419496
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix DGF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse sequence to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix DGF) Service Repair Manua...zan2736ban
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete the job. Precautions are given to contain fluids and prevent contamination.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...f8usejkddmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...prmy389342
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
More Related Content
Similar to Caterpillar Cat 313F and 313F L Excavator (Prefix NLG) Service Repair Manual Instant Download.pdf
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...jse7039222
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...lituo39419496
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
This document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It begins by outlining the required tools and ensuring the engine is properly positioned. Instructions then describe cleaning and inspecting parts, applying lubricant, and aligning timing marks before installation. Torque specifications are provided for fasteners. Final steps include checking clearances and positioning the valve mechanism.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix DGF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse sequence to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix DGF) Service Repair Manua...zan2736ban
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete the job. Precautions are given to contain fluids and prevent contamination.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...f8usejkddmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...prmy389342
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Similar to Caterpillar Cat 313F and 313F L Excavator (Prefix NLG) Service Repair Manual Instant Download.pdf (12)
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820291
Idler Gear - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 364-9107
Timing Pin
(Fuel Injection Pump)
1
C 230-6284
Timing Pin
(Camshaft)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
1/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. (2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the
correct procedure.
Illustration 1 g02491276
2/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01996475
2. Ensure that Tooling (D) is installed in Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct Position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
3. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (3).
4. Use Tooling (B) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
3/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01996477
4/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01996478
5/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g01996576
5. Clean idler gear (4) and inspect the idler gear for wear and damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
6. Clean hub (9) and inspect the hub for wear and damage. Refer to Specifications, "Gear
Group (Front)" for more information. If necessary, replace the hub.
7. Lubricate hub (9) with clean engine oil. Install hub (9) into the recess in the front housing.
Ensure that oil Hole (Z) is to the top of the hub.
8. Install idler gear (4) onto hub (9). Ensure that the timing marks are toward the front of the
idler gear.
9. Align the timing mark on idler gear (4) with the timing mark on camshaft gear (3), fuel
injection pump gear (10) and crankshaft gear (11). Refer to the Illustration 5. Install the
assembly of idler gear (4) to hub (9).
10. Clean plate (8) and inspect the plate for wear and damage. If necessary, replace the plate.
11. Lubricate plate (8) with clean engine oil. Align the holes in plate (8) with the holes in hub
(9). Install the plate in the original orientation.
Note: Ensure that the identification mark TOP is upward.
12. Install bolts (7). Tighten the bolts to a torque of 44 N·m (32 lb ft).
13. Remove Tooling (B), Tooling (C), and Tooling (D).
6/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Note: Ensure that timing marks are aligned, before removing the Tooling (B), Tooling (C),
and Tooling (D).
14. Use Tooling (F) in order to check the end play for the idler gear. Refer to Specifications,
"Gear Group (Front)" for more information.
15. Use Tooling (F) in order to check the backlash between the idler gear and the camshaft gear.
Refer to Specifications, "Gear Group (Front)" for more information.
16. Use Tooling (F) in order to check the backlash between the idler gear and the crankshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
17. Use Tooling (F) in order to check the backlash between the idler gear and the fuel injection
pump gear. Refer to Specifications, "Gear Group (Front)" for more information.
18. Lightly lubricate all of the gears with clean engine oil.
NOTICE
Failure to ensure that the crankshaft is set in the safe position will
result in interference between the pistons and the valves. Interference
between the pistons and the valves will result in damage to the engine.
19. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
7/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 6 g01994556
20. Ensure that the guides for the pushrods are correctly positioned on the threaded inserts (5).
Use Tooling (E) in order to tighten threaded inserts (5) on all rocker arms (6). Tighten the
threaded inserts to a torque of 30 N·m (265 lb in).
Note: When the threaded insert is tightened, the threaded insert must be seated correctly
into the cup for the pushrod.
21. The engine should not be operated for a period 45 minutes after the threaded inserts on all
the rocker arms have been tightened. This period will allow the force of the valve springs to
purge off excessive engine oil from the hydraulic lifters.
8/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g02485936
22. Position a new O-ring seal (2) onto plug (1). Install the plug to the cylinder block and
tighten the plug to a torque of 21 N·m (186 lb in).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:56:27 UTC+0800 2020
9/9
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820292
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02488340
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02488341
6. Remove bolts (10), bolts (11) and bolts (12) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the different bolts.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (13).
3/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02488356
9. Remove thrust washer (14) from cylinder block (15).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:57:24 UTC+0800 2020
4/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820293
Housing (Front) - Remove - Heavy Duty Housing (Front)
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02490356
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02490357
6. Remove bolts (11), bolts (12) and bolts (13) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the bolts of different
length.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (14).
9. If necessary, follow Step 9.a through Step 9.b in order to remove bearing (10) from housing
(7).
a. Place housing (7) onto a suitable support.
b. Use a suitable tool in order to press bearing (10) out of housing (7).
3/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g02490358
10. Remove thrust washer (15) from cylinder block (16).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:58:21 UTC+0800 2020
4/4
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820294
Housing (Front) - Install - Heavy Duty Housing (Front)
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B -
Guide Studs
M8 by 80 mm
2
C
319-6486 Alignment Tool 1
-
Bolts
M10 by 50 mm
3
D 1U-6396 O-Ring Assembly Compound 1
E 7M-7456 Bearing Mount Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Ensure that the wiring harness assembly is correctly routed and the
cable straps are not over tightened. Over tightening of the cable straps
will damage the wiring harness and the convoluting.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal
all D-plugs.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02490396
2/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g02490397
3. Inspect dowel (17) and dowel (18) for damage. If necessary, replace the dowels in the
cylinder block.
4. Install thrust washer (15) into the recess in cylinder block (16). Refer to Disassembly and
Assembly, "Camshaft - Install" for more information.
5. Install Tooling (B) to cylinder block (16). Refer to Illustration 2.
6. Align a new gasket (10) with Tooling (B). Install the gasket to (16) cylinder block.
Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in
cylinder block (16). Ensure that dowel (18) in cylinder block (16) is engaged on the gasket.
7. Install Tooling (C) to cylinder block (16).
3/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 3 g02490399
8. If necessary, follow Step 8.a through Step 8.c in order to install bearing (10) to housing (7).
a. Apply a small continuous bead of Tooling (E) to outer Surface (Z) of bearing (10).
b. Place housing (7) onto a suitable support.
c. Use a suitable tool in order to press bearing (10) into housing (7) until the bearing is
in the correct position within the housing. Remove any excess bearing mount
compound.
9. Install the front housing over Tooling (B) and Tooling (C) onto cylinder block (16).
4/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 4 g02490400
(11) M8 by 35 mm
(12) M8 by 20 mm
(13) M8 by 25 mm
5/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
25. Illustration 5 g02058297
10. Install bolts (13) to front housing (7) finger tight.
11. Remove Tooling (B).
12. Loosely install bolts (11) and bolts (12). Refer to Illustration 4 for the correct position of the
bolts.
13. Tighten bolts (11), bolts (12) and bolts (13) in the sequence that is shown in Illustration 5 to
a torque of 28 N·m (248 lb in).
14. Remove Tooling (C) from the cylinder block.
6/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 6 g02490356
15. Install a new O-ring seal (8) and a new O-ring seal (9) to bypass tube (5). Use Tooling (D)
in order to lubricate the O-ring seals.
16. Install bypass tube (5) to the cylinder head. Install bolts (6). Tighten the bolts to a torque of
9 N·m (80 lb in).
17. Connect harness assembly (2) to coolant temperature sensor (3).
18. Slide locking tab (1) (not shown) into the locked position.
19. Position harness assembly (2) onto bypass tube (5). Install a new cable strap (4).
Note: Ensure that the cable strap meets Original Equipment Manufactures (OEM)
specification.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install" for the correct procedure.
b. Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install"
for the correct procedure.
c. If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
7/8
313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...