This document provides instructions for installing the crankshaft in a Caterpillar C4.2 engine. It involves installing various bearings and seals around the crankshaft and securing it with caps and bolts. The instructions describe lubricating parts, positioning thrust washers and seals correctly, and checking that the crankshaft spins freely after installation. Tolerances for crankshaft end play are also specified to be checked after installation is complete.
Caterpillar cat 312 d excavator (prefix hcw) service repair manual (hcw00001 ...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C7.1 engine. The 3 step summary is:
1. To remove the gear, lock the camshaft and crankshaft, mark alignment of gears, and use a puller tool to remove the gear from the fuel injection pump shaft.
2. To install the gear, ensure proper alignment of gears using timing marks, install the gear on the fuel injection pump shaft, and tighten the nut while applying pressure to remove backlash.
3. Lubricate the gear teeth and install the front cover after installing the fuel injection pump gear.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 312 d excavator (prefix hcw) service repair manual (hcw00001 ...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C7.1 engine. The 3 step summary is:
1. To remove the gear, lock the camshaft and crankshaft, mark alignment of gears, and use a puller tool to remove the gear from the fuel injection pump shaft.
2. To install the gear, ensure proper alignment of gears using timing marks, install the gear on the fuel injection pump shaft, and tighten the nut while applying pressure to remove backlash.
3. Lubricate the gear teeth and install the front cover after installing the fuel injection pump gear.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
Caterpillar cat 312 d l excavator (prefix hcw) service repair manual (hcw0000...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...tuzhiyou2
This document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the crankshaft pulley
- Removing the crankshaft front seal
- Installing a new crankshaft front seal
- Removing just the idler gear from the front gear group
The instructions include illustrations and specify the required tools for each procedure. Safety notices are also provided to keep parts clean and contain fluids properly during maintenance.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...jse7039222
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...lituo39419496
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar cat 323 d ln excavator (prefix wne) service repair manual (wne000...fjskksmem
The document provides instructions for removing the crankshaft from a Caterpillar C6.4 engine. The steps include removing various components like the front housing, rear seal, flywheel housing and oil pan. Then the connecting rod caps, main bearing caps and rear main bearing cap are taken off. Lifting equipment is used to pull out the crankshaft after removing the connecting rods, bearings and thrust washers.
Caterpillar cat 323 d excavator (prefix wne) service repair manual (wne00001 ...soeldksejdksem
The document provides instructions for removing the crankshaft from a Caterpillar C6.4 engine. Key steps include removing the front housing, rear seal, flywheel housing, oil pan, connecting rod caps, crankshaft main bearing caps, and then using a lifting device to pull the crankshaft from the engine block. Proper marking of removed parts is emphasized to ensure correct reinstallation.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
Caterpillar cat 312 d l excavator (prefix hcw) service repair manual (hcw0000...fksjksmmde
1. The document provides instructions for removing and installing a crankshaft position sensor on a Caterpillar C4.2 engine.
2. The removal procedure involves disconnecting the electrical connector and removing the mounting bolts.
3. The installation procedure specifies cleaning parts, applying threadlock to bolts, torquing bolts to specification, and connecting the electrical connector.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...tuzhiyou2
This document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the crankshaft pulley
- Removing the crankshaft front seal
- Installing a new crankshaft front seal
- Removing just the idler gear from the front gear group
The instructions include illustrations and specify the required tools for each procedure. Safety notices are also provided to keep parts clean and contain fluids properly during maintenance.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...jse7039222
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual (XGK00001...lituo39419496
This document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The removal and installation procedures are described in steps and include illustrations of the components. Tools required are listed for each procedure.
Caterpillar cat 323 d ln excavator (prefix wne) service repair manual (wne000...fjskksmem
The document provides instructions for removing the crankshaft from a Caterpillar C6.4 engine. The steps include removing various components like the front housing, rear seal, flywheel housing and oil pan. Then the connecting rod caps, main bearing caps and rear main bearing cap are taken off. Lifting equipment is used to pull out the crankshaft after removing the connecting rods, bearings and thrust washers.
Caterpillar cat 323 d excavator (prefix wne) service repair manual (wne00001 ...soeldksejdksem
The document provides instructions for removing the crankshaft from a Caterpillar C6.4 engine. Key steps include removing the front housing, rear seal, flywheel housing, oil pan, connecting rod caps, crankshaft main bearing caps, and then using a lifting device to pull the crankshaft from the engine block. Proper marking of removed parts is emphasized to ensure correct reinstallation.
Similar to Caterpillar cat 312 d excavator (prefix hcw) service repair manual (hcw00001 and up) (6)
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l vg excavator (prefix sdm) service repair manual (sdm...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l vg excavator (prefix pfd) service repair manual (pfd...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided regarding cleaning, marking parts, and applying lubricant before assembly.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...fjskekxcddmmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02770970
Crankshaft - Install
SMCS - 1202-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-9120 Socket (1)
1
B 8T-5096 Dial Indicator 1
C 8T-9022 Silicone Gasket 1
D 198-9113 Seal Installer 1
( 1 )
Tooling (A) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01377349
1. Install thrust washer (14) on the rear face of the crankshaft with the oil groove toward the
outside.
2. Position the upper halves of crankshaft main bearings (13) in the cylinder block. Install the
bearings with the main bearing tabs in the correct position. Lubricate the bearings with
clean engine oil.
Illustration 2 g01377339
3. Lubricate the crankshaft journals with clean engine oil. Attach a suitable lifting device to
crankshaft (12). The weight of crankshaft (12) is approximately 40 kg (88 lb). Use the
suitable lifting device in order to position crankshaft (12) onto the upper halves of the
crankshaft main bearings.
Note: Be careful not to damage the finished surfaces on the crankshaft.
2/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01377519
This Illustration is of the rear main bearing cap.
4. Install main bearings (11) onto crankshaft main bearing caps (7) (not shown). Install main
bearing (11) onto rear main bearing cap (8). Install bearings (11) with the main bearing tabs
in the correct position. Lubricate main bearings (11) with clean engine oil.
5. Install thrust washers (10) onto rear main bearing cap (8). Make sure that the oil grooves on
thrust washers (10) are facing away from rear main bearing cap (8) .
Illustration 4 g01377377
3/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01385779
6. Apply Tooling (C) to the corners and the sides of rear main bearing cap (8). Install rear
main bearing cap (8) to the cylinder block so that the rear face is even with the rear face of
the cylinder block.
7. Apply soapy water to seals (9). Position seals (9) in the grooves on rear main bearing cap
(8) with the rounded edges of seals (9) toward the outside. Use Tooling (D) in order to push
seals (9) into position. This will reduce the risk of damaging the metal cores of seals (9).
Apply Tooling (C) around seals (9). Cut off any excess length of seals (9) .
Illustration 6 g01385754
8. Install crankshaft main bearing caps (7). Put clean engine oil on the threads of new main
bearing cap bolts (6). Install main bearing cap bolts (6). Tighten main bearing cap bolts (6)
evenly to a torque of 137 ± 5 N·m (101 ± 4 lb ft).
Note: Ensure that crankshaft main bearing caps (7) are installed in the original locations.
4/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01377571
9. Check the end play of the crankshaft with Tooling (B). The end play must be 0.100 to 0.264
mm (0.0039 to 0.0104 inch). Refer to the Specification, "Crankshaft" for more information
on crankshaft end play.
Illustration 8 g01385745
Note: Remove tape or rubber tubing from the connecting rod bolts.
10. Apply a light coat of clean engine oil to the connecting rod bearing surfaces and to the
connecting rod journals. Install the connecting rods onto the connecting rod journals.
11. Install the lower half of the connecting bearings into the corresponding connecting rod caps
and install connecting rod caps (5) .
Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in
connecting rod caps (5). Install new bolts (4) and the new nuts. Tighten bolts (4) to a torque
of 103 ± 5 N·m (76 ± 4 lb ft).
5/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 12. Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
Illustration 9 g01377302
13. Check for free crankshaft rotation by rotating the crankshaft for two complete revolutions.
Use Tooling (A) on nut (3) in order to rotate the crankshaft.
Illustration 10 g01385561
14. Position oil supply tube (1) and the O-ring seal. Install bolts (2) in order to secure the oil
supply tube to the cylinder block.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
6/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. b. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
c. Install the crankshaft rear seal, if the crankshaft wear sleeve was removed. Refer to
Disassembly and Assembly, "Crankshaft Rear Seal - Install".
d. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:12:41 UTC+0800 2020
7/7
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01131265
Crankshaft Gear - Remove and Install
SMCS - 1204-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-0820 Hydraulic Puller 1
9U-6600 Hand Hydraulic Pump 1
0S-2398 Step Plate 1
3H-0468 Puller Plate 4
8B-7549 Puller Leg 2
1B-4207 Full Nut 2
8B-7551 Bearing Puller 1
Start By:
a. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
1/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00541880
1. Use Tool (A) to remove crankshaft gear (1) from crankshaft (2).
Note: Do not remove the gear by tapping with a hammer.
Note: Be careful not to damage the finished surfaces on the crankshaft.
2. Check the key on the crankshaft. If the key is damaged, use a new part for replacement.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Use an oven and heat the crankshaft gear to a temperature of about 100 °C (212 °F). The
crankshaft gear is heated in order to ease installation of the crankshaft gear.
Wear eye protection in order to prevent possible personal injury while
performing the following steps.
2/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: Be careful not to damage the finished surfaces on the crankshaft.
2. Install the crankshaft gear on the end of the crankshaft. Ensure that the key in the crankshaft
is aligned with the keyway in the gear. Tap lightly with a copper hammer until the
crankshaft gear is seated. Ensure that the crankshaft gear is seated against the shoulder on
the crankshaft.
Note: Ensure that the timing marks of the crankshaft gear are on the front.
End By:
a. Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:13:40 UTC+0800 2020
3/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Cat does not recommend the checking of the actual bearing clearances particularly on small
engines. This is because of the possibility of obtaining inaccurate results and the possibility of
damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for
specific wall thickness.
Note: The measurements should be within specifications and the correct bearings should be used.
If the crankshaft journals and the bores for the block and the rods were measured during
disassembly, no further checks are necessary. However, if the technician still wants to measure the
bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals
with small diameters if clearances are less than 0.10 mm (0.004 inch).
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing
surfaces.
The technician must be very careful to use Tooling (A) correctly. The following points must be
remembered:
• Ensure that the backs of the bearings and the bores are clean and dry.
• Ensure that the bearing locking tabs are properly seated in the tab grooves.
• The crankshaft must be free of oil at the contact points of Tooling (A).
1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.
Note: Do not allow Tooling (A) to extend over the edge of the bearing.
2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an
impact wrench. Be careful not to dislodge the bearing when the cap is installed.
Note: Do not turn the crankshaft when Tooling (A) is installed.
3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling
(A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration
1.
2/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01152855
Typical Example
4. Remove all of Tooling (A) before you install the bearing cap.
Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all
parts of Tooling (A) are not the same width. Measure the major width in order to ensure that
the parts are within the specification range. Refer to Specifications Manual, "Connecting
Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct
clearances.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:14:40 UTC+0800 2020
3/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02741821
Crankshaft Position Sensor - Remove and Install - Primary
Speed Timing Sensor
SMCS - 1912-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01374150
1. Disconnect harness assembly (1). Remove bolt (3) and crankshaft position sensor (2).
1/2
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Installation Procedure
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374150
1. Install crankshaft position sensor (2). Install bolt (3). Tighten bolt (3) to a torque of
17 ± 2 N·m (13 ± 1 lb ft). Connect harness assembly (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:15:39 UTC+0800 2020
2/2
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02741883
Coolant Temperature Sensor - Remove and Install
SMCS - 1906-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Drain the coolant from the cooling system into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) -
Change".
1/2
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01374257
2. Disconnect harness assembly (1).
3. Remove water temperature sensor (2) and the O-ring seal.
Installation Procedure
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 2 g01374257
1. Install the O-ring seal onto water temperature sensor (2). Install water temperature sensor
(2). Tighten water temperature sensor (2) to a torque of 15 ± 3 N·m (11 ± 2 lb ft).
2. Connect harness assembly (1).
3. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant (ELC) - Change".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:16:38 UTC+0800 2020
2/2
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02771200
Engine Oil Pressure Sensor - Remove and Install
SMCS - 1924-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01385832
1. Disconnect harness assembly (2) .
2. Remove engine oil pressure sensor (1) and the O-ring seal.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 2 g01385832
1. Install the O-ring seal onto engine oil pressure sensor (1). Install engine oil pressure sensor
(1). Tighten engine oil pressure sensor (1) to a torque of 10 ± 2 N·m (89 ± 18 lb in).
2/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 2. Connect harness assembly (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:17:38 UTC+0800 2020
3/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879394
Position Sensor (Fuel Injection Pump) - Remove and Install
SMCS - 1911; 7400
Removal Procedure
Start By:
A. Remove the hydraulic fuel injection pump. Refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g01377748
1. Remove bolt (2) in order to remove position sensor (1) and the O-ring seal.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seal for wear or for damage. Replace the component, if necessary.
2/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01377748
1. Install the O-ring seal and position sensor (1) . Install bolt (2) .
End By: Install the hydraulic fuel injection pump. Refer to Disassembly and Assembly, "Fuel
Injection Pump - Install". Refer to Disassembly and Assembly, "".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 08:18:37 UTC+0800 2020
3/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR HCW
Configuration: 312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02741932
Fuel Pressure Sensor - Remove and Install
SMCS - 7414-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Turn the disconnect switch OFF when draining and/or removing any
fuel system components.
1/3
312D & 312D L Excavators HCW00001-UP (MACHINE) POWERED BY C4.2 Engi...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...