The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Flywheel installation which requires heating the ring gear, pressing it onto the flywheel, and securing with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and installation using a installer tool and retaining compound.
- Flywheel housing removal by lifting with straps and removing bolts, and installation by cleaning surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and removal of the wear sleeve if needed, and installation by positioning on the engine and tightening the nut.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 304 cr mini hydraulic excavator (prefix nad) service repair m...fikskkdmmd1
This document provides instructions for disassembling a travel motor on a 304CR Mini Hydraulic Excavator. The disassembly procedure involves 27 steps and includes removing plates, barrels, pistons, gears, seals, and other components. Special tools are required and precautions around fluid containment and cleanliness are noted. Detailed illustrations accompany each step.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 d l excavator (prefix xgk) service repair manual (xgk0000...pfiskdmjekm
This document provides instructions for removing and installing the crankshaft pulley and front seal on a Caterpillar C4.2 engine. It describes:
1) Using various tools like pullers and sockets to remove the pulley nut, washer, and pulley.
2) Removing the wear sleeve from the pulley if needed by tapping with a chisel.
3) Heating the wear sleeve and installing it on the pulley with a driver group.
4) Reinstalling the pulley, washer, and nut and tightening to the specified torque.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedure includes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove the housing bolts and housing. The oil seal is then removed from the housing using a driver group. For installation, a new oil seal is installed using the driver group before positioning the housing on the cylinder block with a new gasket and securing bolts. The flywheel and starting motor are then reinstalled at the end.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...cdfzxs
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The summary is:
1. Tools and parts required are listed, including a link bracket and driver group.
2. Removal instructions include removing the electric starting motor, flywheel, bolts securing the housing, and oil seal.
3. Installation instructions specify cleaning surfaces, installing a new gasket and oil seal, positioning the housing, and reinstalling the bolts, flywheel, and electric starting motor.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fjskekxcddmmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using a link bracket and driver group to detach the housing after removing the electric starting motor and flywheel. The installation procedure specifies using a primer and retaining compound on the mating parts and attaching the housing with bolts, then reinstalling the starting motor and flywheel.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedures include:
1) Removing the electric starting motor and flywheel first.
2) Using lifting tools to remove the housing bolts and housing.
3) Inspecting and replacing the dowels and gasket if needed.
4) Cleaning the mating surfaces and installing the new gasket on the cylinder block.
5) Placing the housing back in position and securing it with bolts.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the bolts securing the housing and take off the housing.
3) Removing the oil seal from the housing.
4) Cleaning surfaces and installing a new gasket before reinstalling the housing with new bolts and reinstalling the flywheel.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
Caterpillar cat 320 d lrr excavator (prefix dhe) service repair manual (dhe00...fjsekdmmeed
This document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. The oil pump removal process involves taking off the front housing cover and various gears. The water pump removal requires removing the belt and pump pulley. Both pumps are disassembled by removing mounting components using various tools. Reassembly follows the reverse order and procedures provide guidance on cleaning, inspection and installation of seals.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 304 cr mini hydraulic excavator (prefix nad) service repair m...fikskkdmmd1
This document provides instructions for disassembling a travel motor on a 304CR Mini Hydraulic Excavator. The disassembly procedure involves 27 steps and includes removing plates, barrels, pistons, gears, seals, and other components. Special tools are required and precautions around fluid containment and cleanliness are noted. Detailed illustrations accompany each step.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 d l excavator (prefix xgk) service repair manual (xgk0000...pfiskdmjekm
This document provides instructions for removing and installing the crankshaft pulley and front seal on a Caterpillar C4.2 engine. It describes:
1) Using various tools like pullers and sockets to remove the pulley nut, washer, and pulley.
2) Removing the wear sleeve from the pulley if needed by tapping with a chisel.
3) Heating the wear sleeve and installing it on the pulley with a driver group.
4) Reinstalling the pulley, washer, and nut and tightening to the specified torque.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...dueikdkmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedure includes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove the housing bolts and housing. The oil seal is then removed from the housing using a driver group. For installation, a new oil seal is installed using the driver group before positioning the housing on the cylinder block with a new gasket and securing bolts. The flywheel and starting motor are then reinstalled at the end.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...cdfzxs
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The summary is:
1. Tools and parts required are listed, including a link bracket and driver group.
2. Removal instructions include removing the electric starting motor, flywheel, bolts securing the housing, and oil seal.
3. Installation instructions specify cleaning surfaces, installing a new gasket and oil seal, positioning the housing, and reinstalling the bolts, flywheel, and electric starting motor.
Caterpillar cat 312 d excavator (prefix phh) service repair manual (phh00001 ...fjskekxcddmmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves using a link bracket and driver group to detach the housing after removing the electric starting motor and flywheel. The installation procedure specifies using a primer and retaining compound on the mating parts and attaching the housing with bolts, then reinstalling the starting motor and flywheel.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fhjsjkdmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The procedures include:
1) Removing the electric starting motor and flywheel first.
2) Using lifting tools to remove the housing bolts and housing.
3) Inspecting and replacing the dowels and gasket if needed.
4) Cleaning the mating surfaces and installing the new gasket on the cylinder block.
5) Placing the housing back in position and securing it with bolts.
Caterpillar cat 312 d l excavator (prefix phh) service repair manual (phh0000...fjjskmdmem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the bolts securing the housing and take off the housing.
3) Removing the oil seal from the housing.
4) Cleaning surfaces and installing a new gasket before reinstalling the housing with new bolts and reinstalling the flywheel.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
Similar to Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 and up) (9)
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
Kubota l3130 hst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l3130 gst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It also notes country codes that may be included, such as exceptions for parts in other countries like France (FR). Diagrams of product parts are indexed for locating specific components.
Kubota l3130 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l2900 f tractor parts catalogue manualdfjjsjkemmm
This document provides an index and part listings for an L2900F product. It includes sections for the engine, fuel system, cooling water system, electrical system, clutch, transmission, rear axle, brake, front axle, steering, hydraulic system, hood, labels, and accessories. Each section lists the relevant part numbers, descriptions, quantities, and other specifications for the individual components.
Kubota l2900 dt tractor parts catalogue manualdfjjsjkemmm
The crankcase parts list includes over 230 individual parts that make up the crankcase assembly. It lists each part number, description, quantity used, applicable serial number range, interchangeability, remarks, and weight. Key details included are the total weight of the assembled crankcase (48.5kg/106.7lbs) and that most common individual parts like plugs and seals weigh only a few grams.
Kubota l2800 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using a parts book for a tractor model. It defines the column headings used on parts number pages, including the part reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate if a part is different for other countries. The document then provides an index of parts for the tractor model with the part number and relevant parts book for each item.
Kubota l2800 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using parts books and describes the column headings used on parts number pages. It explains that country codes may be included to indicate if a part is different for other countries. Finally, it lists frequently used parts for a L2800DT/HST tractor, including the part number, description, and reference book for each part.
Kubota l2600 dt tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a cylinder head. It includes a list of 170 parts with information on the part number, description, quantity used, applicable serial number range, interchangeability, and remarks. It notes country codes that may be relevant for part interchangeability between countries like the US, Canada, France, etc. The total weight of the cylinder head component is provided at the end.
Kubota l2500 f tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It lists the column headings used on parts pages including the reference number, part number, description, quantity, serial number range and other details. It then provides an example page from the parts book with over 250 individual part numbers listed for the crankcase component.
Kubota l2500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books. It defines the column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for (e.g. A for USA, CA for Canada, FR for France). An example page from a parts book is then shown listing parts for an engine crankcase, with the corresponding information for each part.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:09:21 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:11:20 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:12:19 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:13:19 UTC+0800 2020
4/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:14:18 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:15:17 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 5 g00611573
5. The following items are components of Tool (A) .
◦ 9U-6147 Stud (6)
◦ 6V-8231 Nut (7)
◦ 9U-6146 Sleeve Assembly (8)
◦ 8T-4244 Nut (9)
6. Use Tool (A) and remove idler shaft (5) from the cylinder block. Check the idler shaft for
wear and damage. Replace the shaft, if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
• In order to remove the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
4/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615420
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00611570
1. Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
2. Install idler shaft (5) onto the cylinder block.
Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If
necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the
idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2"
mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the
crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center
position when these marks are in alignment.
3. Install idler gear (3) onto the idler shaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...