The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures describe using various tools and following steps such as loosening bolts, removing seals and gears, checking alignments, applying sealant and oil, and tightening bolts to specified torques. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fjjsekfksmem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The instructions include diagrams illustrating the components and procedures. Technicians are advised to keep parts clean, contain fluids, and refer to specification documents for torque values.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fujsjekskem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The procedures provide detailed steps and illustrations for each component. Cautions are included to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...hvy7sbkw8e
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...xiapokang564341
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, checking alignments, cleaning parts, and lubricating surfaces. Torque specifications and safety notices are also provided.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...wenxian17880
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, seals, and gears in the specified order and installing components by reversing the removal process. Precautions are outlined such as keeping parts clean and containing fluids.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. The components include the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications. Safety notices are also included to keep parts clean and contain fluids properly.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fjjsekfksmem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The instructions include diagrams illustrating the components and procedures. Technicians are advised to keep parts clean, contain fluids, and refer to specification documents for torque values.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fujsjekskem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The procedures provide detailed steps and illustrations for each component. Cautions are included to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...hvy7sbkw8e
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...xiapokang564341
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, checking alignments, cleaning parts, and lubricating surfaces. Torque specifications and safety notices are also provided.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...wenxian17880
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, seals, and gears in the specified order and installing components by reversing the removal process. Precautions are outlined such as keeping parts clean and containing fluids.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. The components include the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications. Safety notices are also included to keep parts clean and contain fluids properly.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.3B engine, including:
- Removing and installing the crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations for each procedure. Safety and cleaning notes are included. Required tools are listed for each job. Torque specifications are provided where applicable.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure, and technicians are advised to keep parts clean and contain fluids properly during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It describes procedures for removing and installing various engine parts like the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include lists of required tools and torque specifications for fasteners. Cautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note required tools and torque specifications and include illustrations showing the components and repair steps. Safety notices are also provided regarding keeping components clean and containing fluids.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
CASE IH AXIAL-FLOW AF9120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower, unload auger swing, and reel drive. Diagrams show the components and port locations of these valves. It also provides a dynamic description of the hydraulic pump in low pressure standby mode, explaining how pressure is directed to compensator spools when the engine is started to minimize flow and maintain low pressure when no hydraulic functions are active.
CASE IH AXIAL-FLOW AF8120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower, unload auger swing, and reel drive. The main stack valve receives oil directly from the hydraulic pump and contains valves for steering priority, header lift, and unload auger swing. The feeder valve provides hydraulic control for all header functions and contains valves for the reel raise/lower and lateral tilt if equipped. It also describes the hydraulic pump and explains its low pressure standby and high pressure modes of operation.
CASE IH AXIAL-FLOW AF7120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower valve, unloading auger swing valve, and reel drive valve. Diagrams show the components and port locations of the main stack valve and feeder valve. It also provides a dynamic description of the hydraulic pump in low pressure standby mode.
CASE IH AXIAL-FLOW 8230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual that contains sections about the various mechanical and electrical systems of Case IH Axial-Flow combines. The sections cover topics like the engine, transmission, hydraulic systems, cab climate control, electrical systems, attachments and headers, product feeding, threshing, and separation. It is intended to assist with servicing and repair of combines from PIN YDG218533 and above.
CASE IH AXIAL-FLOW 9230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual for Case IH Axial-Flow combines from model years 7230 to 9230. It contains instructions for maintenance, repair, and servicing of the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. Safety warnings are provided throughout and proper protective equipment is advised. The manual is intended solely for qualified service technicians.
CASE IH AXIAL-FLOW 7230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual for Case IH Axial-Flow combines from model years 7230 to 9230. It contains instructions for maintenance, repair, and servicing of the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. Safety warnings are provided throughout and technicians are advised to follow all instructions carefully. The manual is intended only for qualified service personnel.
More Related Content
Similar to Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.3B engine, including:
- Removing and installing the crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations for each procedure. Safety and cleaning notes are included. Required tools are listed for each job. Torque specifications are provided where applicable.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure, and technicians are advised to keep parts clean and contain fluids properly during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It describes procedures for removing and installing various engine parts like the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include lists of required tools and torque specifications for fasteners. Cautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note required tools and torque specifications and include illustrations showing the components and repair steps. Safety notices are also provided regarding keeping components clean and containing fluids.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
Similar to Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf (16)
CASE IH AXIAL-FLOW AF9120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower, unload auger swing, and reel drive. Diagrams show the components and port locations of these valves. It also provides a dynamic description of the hydraulic pump in low pressure standby mode, explaining how pressure is directed to compensator spools when the engine is started to minimize flow and maintain low pressure when no hydraulic functions are active.
CASE IH AXIAL-FLOW AF8120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower, unload auger swing, and reel drive. The main stack valve receives oil directly from the hydraulic pump and contains valves for steering priority, header lift, and unload auger swing. The feeder valve provides hydraulic control for all header functions and contains valves for the reel raise/lower and lateral tilt if equipped. It also describes the hydraulic pump and explains its low pressure standby and high pressure modes of operation.
CASE IH AXIAL-FLOW AF7120 Combines Service Repair Manual (Y8G205001 and up).pdffujsekmdd8di
This document provides an overview of the hydraulic distribution systems on an axial-flow combine, including the primary hydraulic power system. It describes the main stack valve and feeder valve, which control hydraulic functions like the header raise/lower valve, unloading auger swing valve, and reel drive valve. Diagrams show the components and port locations of the main stack valve and feeder valve. It also provides a dynamic description of the hydraulic pump in low pressure standby mode.
CASE IH AXIAL-FLOW 8230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual that contains sections about the various mechanical and electrical systems of Case IH Axial-Flow combines. The sections cover topics like the engine, transmission, hydraulic systems, cab climate control, electrical systems, attachments and headers, product feeding, threshing, and separation. It is intended to assist with servicing and repair of combines from PIN YDG218533 and above.
CASE IH AXIAL-FLOW 9230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual for Case IH Axial-Flow combines from model years 7230 to 9230. It contains instructions for maintenance, repair, and servicing of the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. Safety warnings are provided throughout and proper protective equipment is advised. The manual is intended solely for qualified service technicians.
CASE IH AXIAL-FLOW 7230 Combine Service Repair Manual (from PIN YDG218533 and...fujsekmdd8di
This document is a service manual for Case IH Axial-Flow combines from model years 7230 to 9230. It contains instructions for maintenance, repair, and servicing of the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. Safety warnings are provided throughout and technicians are advised to follow all instructions carefully. The manual is intended only for qualified service personnel.
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes the removal and installation procedures for both Type 1/9RM and Type 2/7BJ engines. The procedures involve removing bolts and nuts, inspecting and replacing gaskets if needed, and reinstalling components in the reverse order of removal while keeping parts clean to prevent damage and wear.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the cylinder block using a lifting device.
2. Inspecting the crankshaft rear seal for leaks and cleaning the housing before installation.
3. Installing the housing by positioning it on guide studs, installing bolts finger tight, checking alignment with a dial indicator, and tightening bolts to the specified torque.
This document provides instructions for removing and installing an engine from a 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, installing mounting hardware, filling fluids, and reinstalling removed components. The purpose is to provide a technician with a procedure to remove and install the backhoe loader engine.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps for installing the engine, connecting various components like the transmission, alternator, and fuel system. Tools required are listed. Photos illustrate each step, and safety notices are included.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters can be removed using a telescoping magnet and should be marked for correct installation. They are lubricated before reinstallation.
- The camshaft is removed after other components. It is carefully installed, avoiding damage to lobes or bearings.
- Camshaft bearings are removed and installed using a special tool, ensuring the oil hole aligns correctly.
- The engine oil pan is removed after draining oil. Setscrews are removed and the gasket replaced before reinstalling the pan with sealant applied in grooves to prevent leaks.
This service repair manual provides instructions for installing an engine on a 416F2 Backhoe Loader. It details 17 steps for installing the engine, including attaching the engine to a lifting device, aligning and bolting components like the bell housing and flywheel, installing engine mounts and panels, connecting wiring harnesses and lines, and filling fluids. The manual also provides supplemental documents for removing and installing additional engine components like the fuel pump, fuel lines, and fuel injector nozzles.
1. The document provides assembly instructions for the transmission of a 416D Backhoe Loader. It lists the required tools and parts and provides illustrations and steps for assembling the transmission components.
2. The transmission is assembled from major components which include the input shaft, reverse shaft, and gears. Needle bearings, seals, springs, plates, and rings are installed on the shafts in the correct order.
3. Proper cleaning of parts, use of transmission oil, and heating of bearings to the specified temperature are noted as important steps in the assembly process.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts to separate the flywheel housing from the engine cylinder block and lifting it off using a lifting device. Inspection and installation
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also describes removing the existing rear seal housing assembly by removing setscrews, protecting the crankshaft during new seal installation, aligning and tightening the new housing assembly setscrews, and installing the flywheel.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to specified torques. Tools and safety precautions are also listed.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and parts, removal steps which include removing bolts and lifting the flywheel off, and installation steps such as cleaning, lubricating, and tightening bolts to specified torques. The instructions are separated into sections for engines with different housing assembly configurations.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to remove the flywheel using a lifting device and remove the bolts and bearing housing. To install the flywheel, it describes heating the flywheel ring gear, positioning the flywheel and tightening the bolts. It also provides instructions for removing and installing the crankshaft rear seal, which involves removing housing bolts and installing the seal using a press and installer tool.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
Illustration 2 g02799899
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
Illustration 3 g02799901
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:04:48 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02800138
1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
Illustration 2 g02799899
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
Illustration 3 g02800140
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:05:44 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g02794824
1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
Illustration 2 g02794825
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g02863884
a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:06:41 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g02795206
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolt (2) in order
to remove crankshaft pulley (1).
Installation Procedure
1. Install crankshaft pulley (1) in the reverse order of removal.
a. Apply clean engine oil to the threads of bolt (2). Tighten bolt (2) to a torque of
255 to 274 N·m (188 to 202 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:07:38 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242559
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g02795123
Illustration 2 g02795124
1. Use a suitable pry bar to remove crankshaft front seal (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1140 Driver 1
B 6V-6640 Sealant 1
Note: The crankshaft front seal should be installed dry. Lubricate the inner rubber portion of the
crankshaft front seal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g02796112
Illustration 4 g02795123
1. Lubricate the inner rubber portion of crankshaft front seal (1). Apply Tooling (B) on
crankshaft front seal (1). Position crankshaft front seal (1) on Tooling (A). Install crankshaft
front seal (1) on the crankshaft.
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:08:35 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02795977
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g02795978
Illustration 3 g02795981
Alignment of timing marks
1. Ensure that Timing Marks (X) on the camshaft gear and the crankshaft gear are aligned.
Refer to Illustration 1.
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
Illustration 2.
3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Refer to Illustration 3.
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 4 g02795984
4. Remove bolts (2), washer (3), and the idler shaft from idler gear (1). Remove idler gear (1)
and the washer.
Illustration 5 g02795985
5. Use Tooling (A) to remove idler gear bearing (4) from idler gear (1).
Installation Procedure
1. Install idler gear (1) in the reverse order of removal.
2. Tighten bolts (2) to a torque of 30 to 34 N·m (22 to 25 lb ft).
a. Ensure that the gears, cylinder block surface, and idler gear (1) are clean and free
from wear or damage. If necessary, replace any components that are worn or
damaged.
b. Lubricate idler gear bearing surface (4) with clean engine oil.
c. Check oil clearance between the idler gear shaft and the idler gear bushing.
d. Check the idler gear shaft outer diameter and the inner diameter for the idler gear
bushing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:09:32 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g02795275
2. Disconnect hose assemblies (1) and (2) from the oil cooler.
Illustration 2 g02795251
3. Remove bolts (4).
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove front housing (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 3 g02864317
3. Apply liquid gasket to the seam between the lower crankcase section (6) and the upper
crankcase section (5).
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g02795251
4. Align a new gasket and install the gasket to the cylinder block.
5. Tighten 13 bolts (4) in a side to side sequence. Tighten bolts (4) to a torque of 24 to 27 N·m
(18 to 20 lb ft)
Illustration 5 g02795275
6. Connect hose assemblies (1) and (2) to the oil cooler.
End By:
a. Install the crankshaft front seal.
b. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Fill" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:10:28 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...