The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions describing how to remove, install, and assemble each part while following safety precautions. Illustrations supplement the text.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fikskkdmmd1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...cdfvvv1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...tuzhiyou2
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator, including:
1) Removing and installing the idler gear, which involves aligning timing marks and using a press tool.
2) Removing and installing the front housing, which requires removing other components and applying a sealant.
3) Removing and installing the valve mechanism cover by removing bolts and reinstalling with specified torque.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...qfyc504378
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and rocker shaft disassembly and assembly. The procedures include lists of required tools and multi-step instructions detailing how to remove bolts, gears, covers, and other parts, align timing marks, and reinstall components in the reverse order of removal while taking precautions against contaminants.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...lituo39419496
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the idler gear, front housing, valve mechanism cover, rocker shaft and push rods. The procedures include using the proper tools, following a specified order of removal and installation steps, aligning timing marks, applying sealant or lubricant as needed, and ensuring proper torque of fasteners.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly, and ensuring timing marks are aligned when reassembling components.
Caterpillar cat 304 e2 mini hydraulic excavator (prefix me4) service repair m...fikskkdmmd1
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly to reassemble the engine correctly.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fikskkdmmd1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar cat 305.5 e2cr mini hydraulic excavator (prefix shw) service repa...cdfvvv1
The document provides instructions for removing and installing various engine components on a Caterpillar 305.5E2CR mini hydraulic excavator powered by a C2.4 engine. The components include the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and disassembling the rocker shaft. The procedures note required tools, removal steps, installation steps including torque specifications and lubrication points.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...tuzhiyou2
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator, including:
1) Removing and installing the idler gear, which involves aligning timing marks and using a press tool.
2) Removing and installing the front housing, which requires removing other components and applying a sealant.
3) Removing and installing the valve mechanism cover by removing bolts and reinstalling with specified torque.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...qfyc504378
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the idler gear, front housing, valve mechanism cover, rocker shaft and push rods, and rocker shaft disassembly and assembly. The procedures include lists of required tools and multi-step instructions detailing how to remove bolts, gears, covers, and other parts, align timing marks, and reinstall components in the reverse order of removal while taking precautions against contaminants.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair ...lituo39419496
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the idler gear, front housing, valve mechanism cover, rocker shaft and push rods. The procedures include using the proper tools, following a specified order of removal and installation steps, aligning timing marks, applying sealant or lubricant as needed, and ensuring proper torque of fasteners.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly, and ensuring timing marks are aligned when reassembling components.
Caterpillar cat 304 e2 mini hydraulic excavator (prefix me4) service repair m...fikskkdmmd1
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly to reassemble the engine correctly.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...paws21610697
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...jiuliu14811471
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...uddksemd8ud
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly, and ensuring timing marks are aligned when reassembling components.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...f7djidksmd3e
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar cat 304 e2 mini hydraulic excavator (prefix me4) service repair m...cdfvvv1
The document provides instructions for servicing the engine of a 304E2 Mini Hydraulic Excavator. It describes procedures for removing and installing various engine parts like the valve mechanism cover, rocker shaft, cylinder head, and more. The steps include draining fluids, removing bolts and brackets, and reinstalling parts in the reverse order of removal while following proper safety practices and torque specifications.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...f8usiedkdmm
The document provides instructions for servicing the engine of a 304E2 Mini Hydraulic Excavator. It describes procedures for removing and installing various engine parts like the valve mechanism cover, rocker shaft, cylinder head, and more. The steps include draining fluids, removing bolts and brackets, and reinstalling parts in the reverse order of removal while following proper safety practices and torque specifications.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...shenjiao97221
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...xie25190
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...s20y0196u
This document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...jiduanbu
This document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...iphg8793466
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
More Related Content
Similar to Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair Manual (PYR00001 and up).pdf
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...paws21610697
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...jiuliu14811471
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...uddksemd8ud
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valves, rocker arms, camshafts, cylinder heads, and other parts. Technicians must follow the specific steps, cleaning and lubricating parts properly, and ensuring timing marks are aligned when reassembling components.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...f7djidksmd3e
The document provides instructions for servicing components of a 304E2 Mini Hydraulic Excavator engine. It includes procedures for removing and installing valve mechanism covers, rocker shafts, push rods, cylinder heads, and camshafts. The instructions note to keep parts clean, identify components, and torque bolts to the specified values.
Caterpillar cat 304 e2 mini hydraulic excavator (prefix me4) service repair m...cdfvvv1
The document provides instructions for servicing the engine of a 304E2 Mini Hydraulic Excavator. It describes procedures for removing and installing various engine parts like the valve mechanism cover, rocker shaft, cylinder head, and more. The steps include draining fluids, removing bolts and brackets, and reinstalling parts in the reverse order of removal while following proper safety practices and torque specifications.
Caterpillar Cat 304E2 Mini Hydraulic Excavator (Prefix ME4) Service Repair Ma...f8usiedkdmm
The document provides instructions for servicing the engine of a 304E2 Mini Hydraulic Excavator. It describes procedures for removing and installing various engine parts like the valve mechanism cover, rocker shaft, cylinder head, and more. The steps include draining fluids, removing bolts and brackets, and reinstalling parts in the reverse order of removal while following proper safety practices and torque specifications.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...shenjiao97221
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...xie25190
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...s20y0196u
This document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...jiduanbu
This document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including:
- Crankshaft rear seal carrier
- Flywheel housing
- Crankshaft pulley
- Crankshaft front seal
- Idler gear
- Housing (front)
The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...iphg8793466
This document provides instructions for servicing various components of a 304E2CR Mini Hydraulic Excavator KC4 engine. It includes procedures for removing and installing components like the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The document provides detailed illustrations and instructions for each procedure, including required tools and torque specifications for fasteners.
Similar to Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix PYR) Service Repair Manual (PYR00001 and up).pdf (11)
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...uddksemd8ud
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing plugs, seals, valves, and connectors in reverse order of removal.
3) Installing the engine oil filter base on the engine using guide studs and bolts, and reconnecting hoses.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position. Lubricate seals and install the pump, securing it with a bushing.
2. Use a measurement tool to check that the rack has the proper travel of 15.70 mm after installation.
3. Repeat the process to install the remaining fuel injection pumps and reinstall the cover.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hydraulic lines, removing bolts and other fasteners, and using lifting devices. A 7 step procedure is then given for disassembling the swivel once it is removed, which involves cleaning it, positioning it on a repair stand, and separating its outer housing from the rotor using bolts and other tools.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and housing components are then removed to separate the rotor from the outside housing.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C MH excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly in reverse order, providing details on installing components and applying sealant or lubricant.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06540930
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tooling
Tool Part Number Part Description Qty
A 387-1314 Idler Gear Tool 1
Start By:
a. Remove front housing.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06014275
1. Ensure that Timing Marks (X) on the idler gear and the crankshaft gear are aligned.
Illustration 2 g06014283
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned.
Illustration 3 g06014290
2/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Illustration 4 g06014314
4. Remove bolts (1), gear control collar (3), and idler gear (2).
Illustration 5 g06014318
5. Use Tooling (A) and a suitable press to remove idler gear bearing (4).
Illustration 6 g06014504
Note: Make a temporary mark on the cylinder block in order to show the position of the oil
hole.
3/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 6. Remove bolts (5) and idler shaft (6).
Installation Procedure
1. Install idler gear (2) in the reverse order of removal.
a. Ensure that the gears, cylinder block surface, and idler gear (2) are clean and free
from wear or damage. If necessary, replace any components that are worn or damaged
b. Lubricate idler shaft (6) with clean engine oil.
c. Lubricate idler gear bearing surface (4) with clean engine oil.
d. Apply clean engine oil to bolts (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:10:40 UTC+0800 2020
4/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06524408
Housing (Front) - Remove and Install
SMCS - 1151-010
Removal Procedure
Table 1
Required Tooling
Tool Part Number Part Description Qty
A — Loctite Hi-Temp Flange Sealant —
Start By:
a. Remove crankshaft pulley.
b. Remove engine oil cooler.
c. Remove camshaft position sensor.
Illustration 1 g06009327
1/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 1. Remove clamp (1). Disconnect hose assembly (2).
Illustration 2 g06009342
2. Remove nut (4) and lifting plate (3).
3. Remove clamp (6) and disconnect hose assembly (5).
Illustration 3 g06009549
4. Disconnect hose assembly (11) (not shown). Remove bolts (9) and elbow (10).
5. Remove bolts (7), front housing (8), and the gasket.
Installation Procedure
1. Install front housing (8) in the reverse order of removal.
a. Apply Tooling (A) to the flange of front housing (8).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:11:37 UTC+0800 2020
2/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06501570
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
Illustration 1 g06000444
1. Remove bolts (5) and bracket (6).
2. Remove bolt (2), clamp (4), and hose assembly (3).
3. Remove bolts (7), valve mechanism cover (1), and the gasket.
Installation Procedure
1. Install valve mechanism cover (1) in the reverse order of removal.
a. Tighten bolts (7) to a torque of 7 N·m to 11 N·m (62 lb in to 97 lb in).
Sat Feb 1 22:12:33 UTC+0800 2020
1/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06546146
Rocker Shaft and Push Rod - Remove and Install
SMCS - 1102-010; 1208-010
Removal Procedure
Start By:
a. Remove valve mechanism cover.
Illustration 1 g06010610
1. Remove bolts (2) and rocker shaft assembly (1).
2. Place an identification mark on pushrods (3) to show the location. Remove pushrods (3).
Note: Identification mark will ensure that the pushrods can be installed in the original
positions. Do not interchange the positions of used pushrods.
Installation Procedure
1. Install pushrods (3) and rocker shaft assembly (1) in the reverse order of removal.
1/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. a. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:13:30 UTC+0800 2020
2/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06547684
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
a. Remove the rocker shaft and pushrods.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Make an identification mark on each rocker arm assembly to show the location.
Note: The components must be reinstalled in the original location. Do not interchange
components.
1/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g06045046
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. On the left end of rocker shaft (6), remove bolts (5) and three washers (10).
3. Remove rocker arm assembly (7) for the inlet valve from rocker shaft (6). Remove support
(1). Remove rocker arm assembly (8) for the exhaust valve from rocker shaft (6). Remove
spring (4).
4. Remove rocker arm assembly (8) for the inlet valve from rocker shaft (6). Remove support
(2). Remove rocker arm assembly (7) for the exhaust valve from rocker shaft (6). Remove
spring (4).
5. Remove rocker arm assembly (8) for the inlet valve from rocker shaft (6). Remove support
(3). Remove rocker arm assembly (7) for the exhaust valve from rocker shaft (6). Remove
spring (4).
6. Remove rocker arm assembly (8) for the inlet valve from rocker shaft (6).
7. On the right end of rocker shaft (6), remove bolt (5) and three washers (10).
8. Remove rocker arm assembly (8) for the exhaust valve and support (9) from right side of
rocker shaft (6).
2/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 2 g02725468
9. Rotate rocker arm shaft (6) and support (9). Remove pin (11). Remove support (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:14:27 UTC+0800 2020
3/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06547686
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The components must be reinstalled in the original location. Do not interchange
components.
1. Ensure that all components are clean and free from wear and damage. Refer to
Specifications, "Rocker Shaft" for more information. If necessary, replace any components
that are worn or damaged.
2. Lubricate all the bores of rocker arm assemblies (7) for the inlet valve and rocker arm
assemblies (8) for the exhaust valve with clean engine oil. Lubricate rocker shaft (6) with
clean engine oil.
1/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g02725468
3. Position support (9) on the right end of rocker arm shaft (6) and install pin (11).
Illustration 2 g06045046
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4. Install rocker arm assembly (7) for the exhaust valve and support (9) on the right side of the
rocker arm shaft (6).
5. Install retaining washer (10) on the right end of rocker arm shaft (6). Install the two washers
and bolt (5).
6. Install rocker arm assembly (8) for the inlet valve on the left side of the rocker arm shaft (6).
7. Install spring (4). Install rocker arm assembly (7) for exhaust valve on rocker shaft (6).
Install support (3). Install rocker arm assembly (8) for inlet valve to rocker shaft (6).
2/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 8. Install spring (4). Install rocker arm assembly (7) for exhaust valve on rocker shaft (6).
Install support (2). Install rocker arm assembly (8) for inlet valve to rocker shaft (6).
9. Install spring (4). Install rocker arm assembly (7) for exhaust valve on rocker shaft (6).
Install support (1). Install rocker arm assembly (8) for inlet valve to rocker shaft (6).
10. Install retaining washers (10) on the left end of rocker arm shaft (6). Install the two washers
(10) and bolt (5).
End By:
a. Install the rocker shaft and pushrods.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:15:24 UTC+0800 2020
3/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06546310
Cylinder Head - Remove and Install
SMCS - 1100-010
Removal Procedure
Start By:
a. Remove rocker arm shaft and pushrods.
b. Remove inlet manifold.
c. Remove exhaust manifold.
d. Remove electronic unit injectors.
e. Remove front housing.
f. Remove glow plugs.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant -
Change" for the correct draining and filling procedures.
Illustration 1 g06013147
2. Remove bolts (1), nut (2), and flange assembly (3).
Illustration 2 g06013167
3. Use a suitable lifting device to remove cylinder head (5). The weight of cylinder head (5) is
approximately 28 kg (61 lb).
4. Remove bolts (4), cylinder head (5), and the cylinder head gasket.
Installation Procedure
1. Install cylinder head (5) in the reverse order of removal.
Table 1
2/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Gasket Dimension (Number) Piston Protrusion
15 0.475 ± 0.525 mm (0.0187 ± 0.0207 inch)
20 0.525 ± 0.575 mm (0.0207 ± 0.0226 inch)
25 0.575 ± 0.625 mm (0.0226 ± 0.0246 inch)
30 0.625 ± 0.675 mm (0.0246 ± 0.0266 inch)
35 0.675 ± 0.725 mm (0.0266 ± 0.0285 inch)
Illustration 3 g06045526
a. Select the cylinder head gasket based on piston protrusion if:
◾ the piston, piston pin, small end bushing, connecting rod, or crankpin bearings
have been replaced.
◾ cylinder head or block have been machined.
If none of the above were done, then install a new cylinder head gasket with the same
mark. Refer to illustration 3 and table 1.
Illustration 4 g06013250
b. Apply clean engine oil to the threads of bolts (4).
3/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. c. Tighten bolts (4) in numerical sequence shown in illustration 4 to a torque of
93 N·m to 98 N·m (69 lb ft to 72 lb ft)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:16:21 UTC+0800 2020
4/4
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06541348
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove cylinder head.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06014635
1. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned.
1/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 2 g06014606
2. Remove lifters (1).
Illustration 3 g06014643
3. Remove bolts (2) and camshaft (3).
Installation Procedure
1. Install camshaft (3) in the reverse order of removal.
a. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 1 22:17:17 UTC+0800 2020
2/2
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305E2 CR MINI HYD EXCAVATOR PYR
Configuration: 305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06547544
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 8B-7551 Puller Assembly 1
Start By:
a. Remove the camshaft.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3
305E2CR Mini Hydraulic Excavator PYR00001-UP (MACHINE) POWERED BY C2...
2020/2/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...