Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair manual (ssc00001 and up)

Service Repair Manual
Models
304E Mini Hydraulic Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304E MINI HYD EXCAVATOR SSC
Configuration: 304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)
Disassembly and Assembly
303E CR, 303.5E, 304E, 305.5E and 305E Mini Hydraulic Excavators Machine
Systems
Media Number -UENR0148-04 Publication Date -01/10/2016 Date Updated -25/10/2016
i06906733
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
C 289-6053 Spanner Wrench 1
Illustration 1 g01243022
1. Install Duo-Cone Seal Gp (53).
1/12304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2. Install bearing (52) and Duo-Cone Seal Gp (51).
3. Install ring gear assembly (49) onto motor housing (50).
4. Use Tooling (C) to install nut (48).
5. Tighten nut (48) to a torque of 240 N·m (177 lb ft).

6. Raise the temperature of bearing (48A).
7. Install bearing (48A) onto shaft (45).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. Install spring (45) and seal (47).

9. Install piston (43), shaft assembly (45), and rockers (44).
10. Install swashplate (42).
11. Install pistons (39), bearing (41), and retainer (40).

injury.
12. Install washers (37) and spring (38).
injury.

13. Use a suitable press and Tooling (B) to install retaining ring (36).
14. Install pins (35).
15. Install barrel (32), discs (33), and plates (34).
16. Install O-ring seals (31).

17. Install piston (30).
18. Install O-ring seals (28), O-ring seal (27), and springs (29).
19. Install bearing (26) and port plate (25).

injury.
20. Install head (23) and bolts (24). Tighten bolts (24) to a torque of 29 ± 5 N·m (21 ± 4 lb ft).
21. Install poppet (22).

22. Install spring (21).
injury.
23. Install the O-ring seal and plug (20). Tighten plug (20) to a torque of 196 ± 15 N·m
(145 ± 11 lb ft).

24. Install washers (16), coupling (17), washer (18), and setscrews (19).
25. Install bearings (14), gear (15), and gears (13).
26. Install retainers (12) and bolts (11). Tighten bolts (11) to a torque of 33 ± 5 N·m
(24 ± 4 lb ft).
10/12304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Do...

27. Install carrier (9) and washer (10).
28. Install bearings (7), gear (8), and gears (6).
29. Install retainer (5) and bolts (4). Tighten bolts (4) to a torque of 33 ± 5 N·m (24 ± 4 lb ft).

30. Install cover (3), ring (1), and plug (2). Tighten plug (2) to a torque of 59 ± 10 N·m
(44 ± 7 lb ft).
End By:
a. Install the final drive and the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Feb 19 19:21:46 UTC+0800 2020

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304E MINI HYD EXCAVATOR SSC
Configuration: 304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)
Disassembly and Assembly
303E CR, 303.5E, 304E, 305.5E and 305E Mini Hydraulic Excavators Machine
Systems
Media Number -UENR0148-04 Publication Date -01/10/2016 Date Updated -25/10/2016
i06799276
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 289-6052 Spanner Wrench 1
E 161-4350 Duo-Cone Seal Installation Gp 1
1. Use Tooling (E) to install Duo-Cone seal (58).

2. Install bearing (59). Use Tooling (E) to install Duo-Cone seal (58).
3. There is a count of 132 balls (57). Install balls (57).
4. Install plug (56).

5. Install ring gear (54) onto motor housing (55).
6. Use Tooling (D) to install nut (53). The torque of nut (53) is 196 ± 9.8 N·m (145 ± 7 lb ft).
7. Install bolts (52) and tighten to a torque of 6 ± 2 N·m (53 ± 18 lb in).
8. Install springs (50) and seal (51).
9. Raise temperature of bearing (48).

10. Install bearing (48) onto shaft (47).
injury.
11. Install pistons (46), balls (49), shaft (47), and bearing (48).
12. Install swashplate (45).

13. Install retainer (44), pistons (42), and bearing (43).
14. Install washers (39), spring (41), and washer (40).

injury.
15. Use a suitable press and Tooling (B) to install retaining ring (38).
16. Install pins (37).
17. Install plate (35) and barrel (36).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

18. Install O-ring seals (34) and backup rings (33).
19. Install piston (32), springs (28), O-ring seal (29), O-ring seals (30), and O-ring seals (31).
20. Install port plate (25), bearing (27), and pins (26).
Note: Make sure that port plate (25) stays aligned with dowel during assembly.

injury.
21. Install head (24) and bolts (23) . Tighten bolts (23) to a torque of 64 ± 4 N·m (47 ± 3 lb ft).
22. Install spool (22).

23. Install spring (21) and retainer (20).
injury.
24. Install the O-ring seal and plug (19).

Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair manual (ssc00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair manual (ssc00001 and up)

Similar to Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair manual (ssc00001 and up) (10)

More from ujfjjkjskkemme

More from ujfjjkjskkemme (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair manual (ssc00001 and up)