This document provides instructions for removing and installing various engine components on a 299D XHP Compact Track Loader, including:
- Diesel particulate filter
- Air inlet heater
- Inlet manifold
- Inlet and exhaust valves
- Engine oil cooler
The instructions include illustrations showing the component locations and numbered steps to disconnect wiring, remove mounting hardware, and install replacement parts in the reverse order of removal. Safety precautions are provided throughout regarding personal protective equipment and releasing spring forces.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...fjjskeknjufksemm
This document provides removal and installation instructions for various components of a 299D XHP Compact Track Loader engine, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. Detailed steps and illustrations are provided for safely removing each component while taking appropriate precautions. The installation process is described as the reverse of removal, with specified torques for reinstalling hardware.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...jjdkksmmdmed
This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...fujsjefskekfksem
This document provides removal and installation instructions for various components of a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. Detailed steps and illustrations are provided for safely removing each component while taking appropriate precautions. The installation process is described as the reverse of removal, with specified torques for reinstalling hardware.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...ujfdjjskkmsme
This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
This document provides removal and installation instructions for several engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for safely removing and installing each component while following proper safety protocols.
This document provides removal and installation instructions for several engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for safely removing and installing each component while following proper safety protocols.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses, removing mounting bolts and other hardware, and installing replacement parts in the reverse order of removal while following torque specifications. Safety precautions and required tools are also outlined.
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fusjfjskefksmem
The document provides instructions for removing and installing components on a Caterpillar 297D2 XHP Multi Terrain Loader including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses and other components, removing bolts and other hardware, cleaning parts, and installing components in the reverse order of removal while following torque specifications. Personal protective equipment and special tools are listed.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...fjjskeknjufksemm
This document provides removal and installation instructions for various components of a 299D XHP Compact Track Loader engine, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. Detailed steps and illustrations are provided for safely removing each component while taking appropriate precautions. The installation process is described as the reverse of removal, with specified torques for reinstalling hardware.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...jjdkksmmdmed
This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...fujsjefskekfksem
This document provides removal and installation instructions for various components of a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. Detailed steps and illustrations are provided for safely removing each component while taking appropriate precautions. The installation process is described as the reverse of removal, with specified torques for reinstalling hardware.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...ujfdjjskkmsme
This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
This document provides removal and installation instructions for several engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for safely removing and installing each component while following proper safety protocols.
This document provides removal and installation instructions for several engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for safely removing and installing each component while following proper safety protocols.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses, removing mounting bolts and other hardware, and installing replacement parts in the reverse order of removal while following torque specifications. Safety precautions and required tools are also outlined.
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fusjfjskefksmem
The document provides instructions for removing and installing components on a Caterpillar 297D2 XHP Multi Terrain Loader including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses and other components, removing bolts and other hardware, cleaning parts, and installing components in the reverse order of removal while following torque specifications. Personal protective equipment and special tools are listed.
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fiksejkskeleudk
The document provides instructions for removing and installing various engine components on a Caterpillar 297D2 XHP Multi Terrain Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal while following specific torque specifications. Safety notices are included regarding handling hot components and releasing spring forces.
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fsejfksekmmd
The document provides instructions for removing and installing components on a Caterpillar 297D2 XHP Multi Terrain Loader including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses and other components, removing bolts and other hardware, cleaning parts, and installing components in the reverse order of removal while applying proper torque to fasteners. Safety precautions are provided regarding hot parts, handling used filters, and releasing spring forces.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...hvy7sbkw8e
This service repair manual provides instructions for removing and installing various engine components on a 297D2 XHP Multi Terrain Loader. The components include the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting harness assemblies, removing bolts and other hardware, using specialty tools as needed, cleaning components, inspecting for wear or damage, and reinstalling components in the reverse order of removal while torquing bolts to the specified values. Safety precautions are provided regarding handling hot parts and releasing spring tension.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...xiapokang564341
This service manual document provides removal and installation instructions for several components of a Caterpillar C3.8 engine, including:
- Diesel particulate filter
- Air inlet heater
- Inlet manifold
- Inlet and exhaust valves
- Engine oil cooler
The instructions include illustrations of the components, numbered parts, and steps to disassemble and reassemble the components, noting any required tools and torque specifications. Safety precautions are also provided.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...wenxian17880
This service repair manual provides instructions for removing and installing various engine components on a 297D2 XHP Multi Terrain Loader. The components include the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting harness assemblies, removing bolts and other hardware, using specialty tools as needed, cleaning components, inspecting for wear or damage, and reinstalling components in the reverse order of removal while torquing bolts to the specified values. Safety precautions are provided regarding handling hot parts and releasing spring tension.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including the water pump, water temperature regulator, flywheel, crankshaft rear seal, and crankshaft rear seal carrier. The procedures describe removing fasteners and other parts, inspecting and cleaning components, installing new seals and gaskets, and torquing bolts to the specified values. Tools required for the jobs are listed. Safety precautions are provided at the beginning regarding working at operating temperature and with engine coolant.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including:
- Removing and installing the water pump, describing loosening guards and belts before removing bolts and the pump.
- Removing and installing the water temperature regulator, noting to disconnect hoses, remove bolts and cover, and install a new gasket.
- Procedures for removing the flywheel, including marking its position, removing bolts and couplings, and inspecting parts for wear before installation.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including the water pump, water temperature regulator, flywheel, crankshaft rear seal, and crankshaft rear seal carrier. The procedures describe removing fasteners and other parts, inspecting and cleaning components, installing new seals and gaskets, and torquing bolts to the specified values. Tools required for the jobs are listed. Safety precautions are provided at the beginning regarding working at operating temperature or with alkali coolant.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fusjezsfkskefmsme
1) The document provides installation instructions for installing a rocker shaft and pushrods on a C2.2 engine. It describes cleaning parts, applying oil, inserting seals, nuts, and bolts in the correct positions and torques.
2) Removal instructions are provided for removing the cylinder head on a 4-cylinder C2.2 engine. It lists prerequisite removal steps and describes draining coolant, loosening bolts in reverse order, and lifting off the head using lifting devices.
3) Reinstallation instructions are provided for installing a cylinder head on a 4-cylinder C2.2 engine. It describes cleaning surfaces, inspecting for distortion, installing dowels and guide bolts, and
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...fjjskeknjufksemm
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Personal protective equipment is recommended when working with spring-loaded components.
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...ujfdjjskkmsme
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Safety notices are included to warn of potential injury from compressed springs.
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...jjdkksmmdmed
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Safety notices are included to warn of potential injury from compressed springs.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix TSN) Service Repair Manual (TSN00001...f7fujksekmdm8u
This document provides the disassembly procedure for a service repair manual of excavator models 324D and 324D L. It outlines 28 steps to disassemble the travel motor, including removing components like the head, O-rings, plates, springs, piston assemblies, seals, and covers. Tools required include an adapter, nuts, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound. Cleanliness is emphasized and all O-rings and gaskets must be replaced during assembly.
Caterpillar Cat 324D L Excavator (Prefix TRH) Service Repair Manual (TRH00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring correct part positioning. Tools required are also listed.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f7fujksekmdm8u
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix PYT) Service Repair Manual (PYT00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the final drive of a 324D L Excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 7 steps for assembly, including installing bearings, determining the correct shim thickness to preload the bearings, and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout and tools including various link brackets and eyebolts are listed.
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and a multi-step process involving removing bolts, covers, gears, seals, and other components. Individual parts are removed using various tools, with attention to alignment marks and component weights. The carrier assembly, ring gears, and housing components are then further disassembled to access internal planetary gears and bearings.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...f7fujksekmdm8u
The document provides instructions for disassembling a final drive assembly. Key steps include removing the cover, gears, carrier assembly, planetary carrier, and planetary gears. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations and alignment marks can aid this. Various tools are required, including link brackets and eyebolts to lift components by weight.
Caterpillar Cat 324D L Excavator (Prefix JZR) Service Repair Manual (JZR00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
Caterpillar Cat 324D L Excavator (Prefix JAT) Service Repair Manual (JAT00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves applying thread lock compound and ensuring proper installation of keys, seals, and bearing races. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...f7fujksekmdm8u
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes how to remove and install various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The procedures provide the required tools and step-by-step instructions for each repair, emphasizing the need to keep components clean and free of contaminants.
More Related Content
Similar to Caterpillar Cat 299D XHP COMPACT TRACK LOADER (Prefix NLC) Service Repair Manual (NLC00001 and up).pdf
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fiksejkskeleudk
The document provides instructions for removing and installing various engine components on a Caterpillar 297D2 XHP Multi Terrain Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal while following specific torque specifications. Safety notices are included regarding handling hot components and releasing spring forces.
Caterpillar cat 297 d2 xhp multi terrain loader (prefix hp2) service repair m...fsejfksekmmd
The document provides instructions for removing and installing components on a Caterpillar 297D2 XHP Multi Terrain Loader including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses and other components, removing bolts and other hardware, cleaning parts, and installing components in the reverse order of removal while applying proper torque to fasteners. Safety precautions are provided regarding hot parts, handling used filters, and releasing spring forces.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...hvy7sbkw8e
This service repair manual provides instructions for removing and installing various engine components on a 297D2 XHP Multi Terrain Loader. The components include the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting harness assemblies, removing bolts and other hardware, using specialty tools as needed, cleaning components, inspecting for wear or damage, and reinstalling components in the reverse order of removal while torquing bolts to the specified values. Safety precautions are provided regarding handling hot parts and releasing spring tension.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...xiapokang564341
This service manual document provides removal and installation instructions for several components of a Caterpillar C3.8 engine, including:
- Diesel particulate filter
- Air inlet heater
- Inlet manifold
- Inlet and exhaust valves
- Engine oil cooler
The instructions include illustrations of the components, numbered parts, and steps to disassemble and reassemble the components, noting any required tools and torque specifications. Safety precautions are also provided.
Caterpillar Cat 297D2 XHP MULTI TERRAIN LOADER (Prefix HP2) Service Repair Ma...wenxian17880
This service repair manual provides instructions for removing and installing various engine components on a 297D2 XHP Multi Terrain Loader. The components include the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting harness assemblies, removing bolts and other hardware, using specialty tools as needed, cleaning components, inspecting for wear or damage, and reinstalling components in the reverse order of removal while torquing bolts to the specified values. Safety precautions are provided regarding handling hot parts and releasing spring tension.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including the water pump, water temperature regulator, flywheel, crankshaft rear seal, and crankshaft rear seal carrier. The procedures describe removing fasteners and other parts, inspecting and cleaning components, installing new seals and gaskets, and torquing bolts to the specified values. Tools required for the jobs are listed. Safety precautions are provided at the beginning regarding working at operating temperature and with engine coolant.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including:
- Removing and installing the water pump, describing loosening guards and belts before removing bolts and the pump.
- Removing and installing the water temperature regulator, noting to disconnect hoses, remove bolts and cover, and install a new gasket.
- Procedures for removing the flywheel, including marking its position, removing bolts and couplings, and inspecting parts for wear before installation.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including the water pump, water temperature regulator, flywheel, crankshaft rear seal, and crankshaft rear seal carrier. The procedures describe removing fasteners and other parts, inspecting and cleaning components, installing new seals and gaskets, and torquing bolts to the specified values. Tools required for the jobs are listed. Safety precautions are provided at the beginning regarding working at operating temperature or with alkali coolant.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fusjezsfkskefmsme
1) The document provides installation instructions for installing a rocker shaft and pushrods on a C2.2 engine. It describes cleaning parts, applying oil, inserting seals, nuts, and bolts in the correct positions and torques.
2) Removal instructions are provided for removing the cylinder head on a 4-cylinder C2.2 engine. It lists prerequisite removal steps and describes draining coolant, loosening bolts in reverse order, and lifting off the head using lifting devices.
3) Reinstallation instructions are provided for installing a cylinder head on a 4-cylinder C2.2 engine. It describes cleaning surfaces, inspecting for distortion, installing dowels and guide bolts, and
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...fjjskeknjufksemm
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Personal protective equipment is recommended when working with spring-loaded components.
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...ujfdjjskkmsme
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Safety notices are included to warn of potential injury from compressed springs.
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...jjdkksmmdmed
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Safety notices are included to warn of potential injury from compressed springs.
Similar to Caterpillar Cat 299D XHP COMPACT TRACK LOADER (Prefix NLC) Service Repair Manual (NLC00001 and up).pdf (12)
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix TSN) Service Repair Manual (TSN00001...f7fujksekmdm8u
This document provides the disassembly procedure for a service repair manual of excavator models 324D and 324D L. It outlines 28 steps to disassemble the travel motor, including removing components like the head, O-rings, plates, springs, piston assemblies, seals, and covers. Tools required include an adapter, nuts, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound. Cleanliness is emphasized and all O-rings and gaskets must be replaced during assembly.
Caterpillar Cat 324D L Excavator (Prefix TRH) Service Repair Manual (TRH00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring correct part positioning. Tools required are also listed.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f7fujksekmdm8u
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix PYT) Service Repair Manual (PYT00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the final drive of a 324D L Excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 7 steps for assembly, including installing bearings, determining the correct shim thickness to preload the bearings, and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout and tools including various link brackets and eyebolts are listed.
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and a multi-step process involving removing bolts, covers, gears, seals, and other components. Individual parts are removed using various tools, with attention to alignment marks and component weights. The carrier assembly, ring gears, and housing components are then further disassembled to access internal planetary gears and bearings.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...f7fujksekmdm8u
The document provides instructions for disassembling a final drive assembly. Key steps include removing the cover, gears, carrier assembly, planetary carrier, and planetary gears. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations and alignment marks can aid this. Various tools are required, including link brackets and eyebolts to lift components by weight.
Caterpillar Cat 324D L Excavator (Prefix JZR) Service Repair Manual (JZR00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
Caterpillar Cat 324D L Excavator (Prefix JAT) Service Repair Manual (JAT00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves applying thread lock compound and ensuring proper installation of keys, seals, and bearing races. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...f7fujksekmdm8u
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes how to remove and install various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The procedures provide the required tools and step-by-step instructions for each repair, emphasizing the need to keep components clean and free of contaminants.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...f7fujksekmdm8u
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
Caterpillar Cat 324D L Excavator (Prefix BTK) Service Repair Manual (BTK00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D L and 324D LN. The disassembly procedure is outlined in 28 steps and includes removing components like the head, seals, springs, plates, and bearings. The assembly procedure is outlined in 15 steps and includes installing components in the reverse order of disassembly and applying thread lock compound to seals. Tools required are also listed.
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in the reverse order and notes that all seals and gaskets must be replaced, parts must be cleaned before assembly, and lubricant applied to components. Proper tooling is listed for removing and installing retaining rings, seals, and races.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown, and remove plugs from the cover.
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes how to remove and install various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The procedures provide the required tools and step-by-step instructions for each repair, emphasizing the need to keep components clean and free of contaminants.
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves applying thread lock compound and ensuring proper installation of keys, seals, and bearing races. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- The flywheel, which is removed using lifting brackets and guide bolts.
- The crankshaft rear seal, which is removed using a drill bit and slide hammer puller.
- The flywheel housing, which is removed after draining fluids using lifting brackets and bolts.
- The vibration damper and pulley, which are removed after loosening bolts and removing the drive belt.
Caterpillar Cat 323F L Excavator (Prefix NCW) Service Repair Manual (NCW00001...f7fujksekmdm8u
This document provides instructions for removing and installing the cylinder head on a Caterpillar C7.1 engine. The removal process involves draining coolant, disconnecting wiring harnesses and sensors, and removing mounting brackets. Bolts are then loosened in a specific sequence before lifting the cylinder head off. Installation requires cleaning surfaces, installing a new gasket, and lifting the cylinder head into place using guide studs before tightening bolts in the reverse removal sequence.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes applying sealant, installing seals, plates, springs and other components in the correct order and orientation. Special care must be taken with keys and pins to prevent damage during assembly.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i07500660
Diesel Particulate Filter - Remove and Install
SMCS - 108F-010
Removal Procedure
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will
become extremely hot during engine operation. A hot muffler, catalytic
converter/muffler and diesel particulate filter can cause serious burns.
Allow adequate cooling time before working on or near the muffler,
catalytic converter/muffler and diesel particulate filter.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
1/4
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
Start By:
a. Remove the engine.
Illustration 1 g06048047
1. Disconnect harness assembly (1) and harness assemblies (2). Remove the connecting
hardware.
Illustration 2 g02893984
2. Remove bolts (3).
2/4
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02893982
3. Remove bolts (4). Repeat this step for the opposite side.
Illustration 4 g02894044
4. Use two people to remove diesel particulate filter (5).
Illustration 5 g02920386
3/4
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Remove bolts (6), pressure sensor (7), and tube assemblies (8).
Installation Procedure
1. Install diesel particulate filter (5) in the reverse order of removal.
a. Tighten bolts (3) and bolts (4) to a torque of 52 ± 3 N·m (38 ± 2 lb ft).
b. Tighten tube assemblies (8) to a torque of 19 ± 3 N·m (168 ± 27 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:26:58 UTC+0800 2019
4/4
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04770500
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
Illustration 1 g02870556
1. Disconnect harness assemblies (1).
1/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g02870616
2. Disconnect harness assembly (2) and cable assembly (3).
Illustration 3 g02870576
3. Remove bolts (4) and bolts (5). Remove flange (6), valve assembly (7), air inlet heater (8),
and the gaskets.
Installation Procedure
1. Install new gaskets, air inlet heater (8), valve assembly (7), and flange (6) in the reverse
order of removal.
a. Tighten the nut for cable assembly (3) to a torque of 4.4 ± 0.9 N·m (38.9 ± 8.0 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:27:54 UTC+0800 2019
2/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617508
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
a. Remove the fuel injection manifold.
b. Remove the intake air heater.
c. Remove the exhaust gas valve.
1/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g02858877
1. Remove bolts (1) and bolts (2). Remove inlet manifold (3) and gasket (4).
Installation Procedure
1. Install inlet manifold (3) in the reverse order of removal.
End By:
a. Install the exhaust gas valve.
b. Install the intake air heater.
c. Install the fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:28:49 UTC+0800 2019
2/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06622996
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
B
4C-8134 Seal Remover 1
1U-7600 Slide Hammer Puller Gp 1
Start By:
a. Remove the cylinder head assembly.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves to identify the correct
position.
Note: Do not stamp the heads of the valves. Stamping or punching the heads of the valves
could cause the valves to fracture.
Personal injury can result from being struck by parts propelled by a
released spring force.
1/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 1 g01333469
Typical example
2/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01333471
Typical example
3. Use Tooling (A) to compress the appropriate valve spring (3). Remove valve keepers (1).
Note: Do not compress the valve spring so that valve spring retainer (2) touches valve stem
seal (4).
4. Remove Tooling (A).
5. Remove valve spring retainer (2). Remove valve spring (3).
6. Remove valve (5).
7. Use Tooling (B) to remove valve stem seal (4).
8. Repeat Steps 3 through 7 to remove the remaining inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
3/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. C
4C-6373 Seal Installer 1
4C-6366 Valve Guide Driver 1
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.e to inspect the components of the cylinder head assembly. Replace any
components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Systems Operation,
Testing and Adjusting, "Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves".
e. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder
Head Valves".
Illustration 3 g01333472
Typical example
4/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Use Tooling (C) to install new valve stem seals (4) onto each of the valve guides.
Illustration 4 g01333471
Typical example
Illustration 5 g02891838
3. Lubricate the stem of valve (5) with clean engine oil. Install valve (5) in the appropriate
position in the cylinder head. Check the depth of the valve below the face of the cylinder
head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
5/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 4. Install valve spring (3) to the cylinder head. Orientate valve spring (3) with the small pitch
downward, as indicated. Position valve spring retainer (2) onto valve spring (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 6 g01333469
6/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Typical example
5. Use Tooling (A) to compress valve spring (3). Install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
6. Remove Tooling (A).
7. Repeat Steps 3 to 6 for the remaining valves.
8. Place the cylinder head on a suitable support. Ensure that the heads of the valves are not
obstructed. Gently strike the top of the valves with a soft hammer to ensure that valve
keepers (1) are properly installed.
End By:
a. Install the cylinder head assembly.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:29:45 UTC+0800 2019
7/7
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617576
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Illustration 1 g02798327
1. Remove oil filter (2). Refer to Operation and Maintenance Manual, "Engine Oil and Filter -
Change" for the correct draining and filling procedure.
2. Disconnect hose (1).
1/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g02858919
3. Remove joint screw (3). Remove oil cooler (4).
Illustration 3 g02858921
4. Remove seal (5) from oil cooler (4).
Installation Procedure
1. Install oil cooler (4) in the reverse order of removal.
a. Tighten joint screw (3) to a torque of 42 N·m ± 2 N·m (31 ± 2 lb ft).
b. Fill the engine oil pan to the correct level. Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change" for the correct draining and filling
procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:30:41 UTC+0800 2019
2/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664109
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Illustration 1 g02859497
Illustration 2 g02867660
1/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and seal (2)
2. Remove spring (3) and relief valve (4)
Installation Procedure
1. Install relief valve (4) in the reverse order of removal
a. Tighten plug (1) to a torque of 73.5 ± 4.5 N·m (54.2 ± 3.3 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:31:37 UTC+0800 2019
2/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617636
Engine Oil Pump - Remove and Install
SMCS - 1304-010; 1315-010
Removal Procedure
Start By:
a. Remove the front housing.
Illustration 1 g02797922
1. Remove screws (1). Remove oil pump cover (2).
1/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g02860156
2. Remove oil pump rotors (3).
Installation Procedure
1. Install the engine oil pump in the reverse order of removal.
a. Tighten screws (1) to a torque of 8.6 ± 0.7 N·m (76.1 ± 6.2 lb in).
End By:
a. Install the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:32:32 UTC+0800 2019
2/2
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617810
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
1. Refer to Operation and Maintenance Manual, "Radiator Tilting".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
fill cap is cool enough to touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with the skin
and eyes to prevent personal injury.
2. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedure.
1/3
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g06048252
SSL, MTL, and CTL
Illustration 2 g06048291
CWL
3. For the SSL, MTL, and CTL models, loosen quarter turn fasteners (2). For the CWL models
loosen the four bolts (2). Remove guard (1).
2/3
299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...