This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i07500660
Diesel Particulate Filter - Remove and Install
SMCS - 108F-010
Removal Procedure
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will
become extremely hot during engine operation. A hot muffler, catalytic
converter/muffler and diesel particulate filter can cause serious burns.
Allow adequate cooling time before working on or near the muffler,
catalytic converter/muffler and diesel particulate filter.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
1/4299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
Start By:
a. Remove the engine.
Illustration 1 g06048047
1. Disconnect harness assembly (1) and harness assemblies (2). Remove the connecting
hardware.
Illustration 2 g02893984
2. Remove bolts (3).
2/4299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02893982
3. Remove bolts (4). Repeat this step for the opposite side.
Illustration 4 g02894044
4. Use two people to remove diesel particulate filter (5).
Illustration 5 g02920386
3/4299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Remove bolts (6), pressure sensor (7), and tube assemblies (8).
Installation Procedure
1. Install diesel particulate filter (5) in the reverse order of removal.
a. Tighten bolts (3) and bolts (4) to a torque of 52 ± 3 N·m (38 ± 2 lb ft).
b. Tighten tube assemblies (8) to a torque of 19 ± 3 N·m (168 ± 27 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:26:58 UTC+0800 2019
4/4299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04770500
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
Illustration 1 g02870556
1. Disconnect harness assemblies (1).
1/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g02870616
2. Disconnect harness assembly (2) and cable assembly (3).
Illustration 3 g02870576
3. Remove bolts (4) and bolts (5). Remove flange (6), valve assembly (7), air inlet heater (8),
and the gaskets.
Installation Procedure
1. Install new gaskets, air inlet heater (8), valve assembly (7), and flange (6) in the reverse
order of removal.
a. Tighten the nut for cable assembly (3) to a torque of 4.4 ± 0.9 N·m (38.9 ± 8.0 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:27:54 UTC+0800 2019
2/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617508
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
a. Remove the fuel injection manifold.
b. Remove the intake air heater.
c. Remove the exhaust gas valve.
1/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g02858877
1. Remove bolts (1) and bolts (2). Remove inlet manifold (3) and gasket (4).
Installation Procedure
1. Install inlet manifold (3) in the reverse order of removal.
End By:
a. Install the exhaust gas valve.
b. Install the intake air heater.
c. Install the fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:28:49 UTC+0800 2019
2/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06622996
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
B
4C-8134 Seal Remover 1
1U-7600 Slide Hammer Puller Gp 1
Start By:
a. Remove the cylinder head assembly.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves to identify the correct
position.
Note: Do not stamp the heads of the valves. Stamping or punching the heads of the valves
could cause the valves to fracture.
Personal injury can result from being struck by parts propelled by a
released spring force.
1/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 1 g01333469
Typical example
2/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01333471
Typical example
3. Use Tooling (A) to compress the appropriate valve spring (3). Remove valve keepers (1).
Note: Do not compress the valve spring so that valve spring retainer (2) touches valve stem
seal (4).
4. Remove Tooling (A).
5. Remove valve spring retainer (2). Remove valve spring (3).
6. Remove valve (5).
7. Use Tooling (B) to remove valve stem seal (4).
8. Repeat Steps 3 through 7 to remove the remaining inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
3/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. C
4C-6373 Seal Installer 1
4C-6366 Valve Guide Driver 1
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.e to inspect the components of the cylinder head assembly. Replace any
components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Systems Operation,
Testing and Adjusting, "Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves".
e. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder
Head Valves".
Illustration 3 g01333472
Typical example
4/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Use Tooling (C) to install new valve stem seals (4) onto each of the valve guides.
Illustration 4 g01333471
Typical example
Illustration 5 g02891838
3. Lubricate the stem of valve (5) with clean engine oil. Install valve (5) in the appropriate
position in the cylinder head. Check the depth of the valve below the face of the cylinder
head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
5/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 4. Install valve spring (3) to the cylinder head. Orientate valve spring (3) with the small pitch
downward, as indicated. Position valve spring retainer (2) onto valve spring (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 6 g01333469
6/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Typical example
5. Use Tooling (A) to compress valve spring (3). Install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
6. Remove Tooling (A).
7. Repeat Steps 3 to 6 for the remaining valves.
8. Place the cylinder head on a suitable support. Ensure that the heads of the valves are not
obstructed. Gently strike the top of the valves with a soft hammer to ensure that valve
keepers (1) are properly installed.
End By:
a. Install the cylinder head assembly.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:29:45 UTC+0800 2019
7/7299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617576
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Illustration 1 g02798327
1. Remove oil filter (2). Refer to Operation and Maintenance Manual, "Engine Oil and Filter -
Change" for the correct draining and filling procedure.
2. Disconnect hose (1).
1/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g02858919
3. Remove joint screw (3). Remove oil cooler (4).
Illustration 3 g02858921
4. Remove seal (5) from oil cooler (4).
Installation Procedure
1. Install oil cooler (4) in the reverse order of removal.
a. Tighten joint screw (3) to a torque of 42 N·m ± 2 N·m (31 ± 2 lb ft).
b. Fill the engine oil pan to the correct level. Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change" for the correct draining and filling
procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:30:41 UTC+0800 2019
2/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664109
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Illustration 1 g02859497
Illustration 2 g02867660
1/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and seal (2)
2. Remove spring (3) and relief valve (4)
Installation Procedure
1. Install relief valve (4) in the reverse order of removal
a. Tighten plug (1) to a torque of 73.5 ± 4.5 N·m (54.2 ± 3.3 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:31:37 UTC+0800 2019
2/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617636
Engine Oil Pump - Remove and Install
SMCS - 1304-010; 1315-010
Removal Procedure
Start By:
a. Remove the front housing.
Illustration 1 g02797922
1. Remove screws (1). Remove oil pump cover (2).
1/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g02860156
2. Remove oil pump rotors (3).
Installation Procedure
1. Install the engine oil pump in the reverse order of removal.
a. Tighten screws (1) to a torque of 8.6 ± 0.7 N·m (76.1 ± 6.2 lb in).
End By:
a. Install the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 31 23:32:32 UTC+0800 2019
2/2299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D XHP COMPACT TRACK LOADER NLC
Configuration: 299D XHP Compact Track Loader NLC00001-UP (MACHINE)
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06617810
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
1. Refer to Operation and Maintenance Manual, "Radiator Tilting".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
fill cap is cool enough to touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with the skin
and eyes to prevent personal injury.
2. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedure.
1/3299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g06048252
SSL, MTL, and CTL
Illustration 2 g06048291
CWL
3. For the SSL, MTL, and CTL models, loosen quarter turn fasteners (2). For the CWL models
loosen the four bolts (2). Remove guard (1).
2/3299D XHP Compact Track Loader NLC00001-UP (MACHINE)(SEBP5951 - 31) - Do...
2019/10/31https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...