This document provides instructions for removing a piston motor (hydrostatic) from a 287C Multi Terrain Loader. The steps include: releasing system pressure, removing the track and track drive, disconnecting hoses and harnesses, and using lifting tools to remove the track drive assembly which contains the piston motor. Identification marks should be put on disconnected parts to aid reinstallation.
Caterpillar cat 287 c multi terrain loader (prefix mas) service repair manual...uujjfjkkkdmme
This document provides instructions for removing a piston motor (hydrostatic) from a 287C Multi Terrain Loader. The steps include: releasing system pressure, removing the track and track drive, disconnecting hoses and harnesses, and using lifting tools to remove the track drive assembly which contains the piston motor. Identification marks should be put on disconnected parts to aid reinstallation.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...ujfjjskekfmmde
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include relieving hydraulic pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fusjfjskefksmem
The document provides instructions for removing and installing a piston pump (hydrostatic) from a 297C Multi Terrain Loader. It describes using various tools to remove bolts and brackets holding the pump in place. Hoses and electrical harnesses connected to the pump must be disconnected and plugged. With the attachments removed, a lifting device can be used to remove the 73 kg pump from the machine. Precautions are listed to relieve pressure and contain fluids during removal.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty0...fjjskekdmme
This document provides assembly instructions for a final drive in 29 steps. It begins by cleaning all parts and checking seals. It then details assembling bearings and gears in sequence using various tools. Precise measurements are taken to determine the correct shim thickness for proper bearing preload. Multiple planetary gear carrier assemblies are installed along with retaining rings and bolts. Proper torque specifications are listed throughout.
Caterpillar cat w345 b series ii material handler (prefix cdy) service repair...fjjsieskekfmmse
This document provides assembly instructions for the swing drive of a W345B Series II Material Handler excavator. It lists the required tools and lubricants and outlines a 36 step process for assembling the various components of the swing drive, including bearings, seals, gears, housings, and fasteners. Special attention is given to cleaning parts, applying lubricants, setting torque specifications, and heating components to aid in assembly.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 323 d2 l excavator (prefix kbx) service repair manual (kbx000...fusjejkdkmse
This document provides assembly instructions for the final drive of a 323D2 L excavator. It outlines 35 steps to assemble the components, including installing bearings, seals, gears, carriers, plugs and other parts. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process to prevent contamination.
Caterpillar cat 287 c multi terrain loader (prefix mas) service repair manual...uujjfjkkkdmme
This document provides instructions for removing a piston motor (hydrostatic) from a 287C Multi Terrain Loader. The steps include: releasing system pressure, removing the track and track drive, disconnecting hoses and harnesses, and using lifting tools to remove the track drive assembly which contains the piston motor. Identification marks should be put on disconnected parts to aid reinstallation.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...ujfjjskekfmmde
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include relieving hydraulic pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fusjfjskefksmem
The document provides instructions for removing and installing a piston pump (hydrostatic) from a 297C Multi Terrain Loader. It describes using various tools to remove bolts and brackets holding the pump in place. Hoses and electrical harnesses connected to the pump must be disconnected and plugged. With the attachments removed, a lifting device can be used to remove the 73 kg pump from the machine. Precautions are listed to relieve pressure and contain fluids during removal.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty0...fjjskekdmme
This document provides assembly instructions for a final drive in 29 steps. It begins by cleaning all parts and checking seals. It then details assembling bearings and gears in sequence using various tools. Precise measurements are taken to determine the correct shim thickness for proper bearing preload. Multiple planetary gear carrier assemblies are installed along with retaining rings and bolts. Proper torque specifications are listed throughout.
Caterpillar cat w345 b series ii material handler (prefix cdy) service repair...fjjsieskekfmmse
This document provides assembly instructions for the swing drive of a W345B Series II Material Handler excavator. It lists the required tools and lubricants and outlines a 36 step process for assembling the various components of the swing drive, including bearings, seals, gears, housings, and fasteners. Special attention is given to cleaning parts, applying lubricants, setting torque specifications, and heating components to aid in assembly.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 323 d2 l excavator (prefix kbx) service repair manual (kbx000...fusjejkdkmse
This document provides assembly instructions for the final drive of a 323D2 L excavator. It outlines 35 steps to assemble the components, including installing bearings, seals, gears, carriers, plugs and other parts. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process to prevent contamination.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 430 d backhoe loader (prefix bnk) service repair manual (bnk0...fhsjejfsekkkm
The document provides instructions for assembling and installing the transmission on a 430D backhoe loader. It details assembling the various transmission components like bearings, gears, shafts, and cases. It also describes installing the assembled transmission into the vehicle and making final connections. The transmission assembly involves multiple steps of pressing, heating, and inserting components in the correct order.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat 438 d backhoe loader (prefix bpe) service repair manual (bpe0...udfjjjskekdme
The document provides instructions for assembling the transmission of a 438D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, and cases in their proper order. Tools needed for the assembly are listed. Cleanliness is emphasized and components should be cleaned and oiled before installation. Tolerances for shaft play are provided to check proper assembly. The transmission is then installed in the vehicle and filled with the specified oil.
Caterpillar cat 160 k motor grader (prefix szm) service repair manual (szm000...fjjsekkskeoelkm
This document provides instructions for assembling and installing the final drive on a 160K motor grader. The 30-step assembly procedure includes installing bearings, seals, sprockets, housing components, and fasteners in the correct order. Technicians are instructed to clean all parts thoroughly, apply lubricant where specified, and tighten fasteners to the proper torque specifications. The summary concludes by stating the final drives are installed and the tandem housing is attached.
Caterpillar cat 140 m motor grader (prefix b9d) service repair manual (b9d000...ufjjsejfkskemme
This document provides instructions for removing and installing rear gear group components on a 140M Motor Grader. It describes removing the flywheel, gear assembly, bearings, and seals. Detailed steps are provided with accompanying illustrations showing the specific components and tools used. Precautions are outlined such as keeping parts clean and properly installing bearings at the correct angles and distances.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fhsjejfsekkkm
The document provides instructions for assembling and installing a transmission (direct drive) for a 430D backhoe loader. It describes cleaning and lubricating transmission components before assembly. It then provides step-by-step instructions to assemble the transmission case, input shaft, reverse shaft, output shafts, and final assembly. It describes using various tools and heating bearing cones to specified temperatures. Finally, it outlines installing the assembled transmission on the backhoe loader.
Caterpillar cat 287 c multi terrain loader (prefix mas) service repair manual...fujsefkskemm
The document provides instructions for removing and assembling a piston pump (hydrostatic pump) from a 287C Multi Terrain Loader. It describes disconnecting hoses and removing mounting bolts to detach the pump. It then details disassembling the pump by removing bearings, seals, pistons, and other internal components. Finally, it explains testing the reassembled pump before reinstalling it in the vehicle.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fiksejkskeleudk
The document provides instructions for removing and installing a piston pump (hydrostatic) from a 297C Multi Terrain Loader. It describes using lifting equipment to remove the 73 kg pump and disconnecting hydraulic hoses and electrical harnesses. Detailed steps are given to disassemble the pump by removing plates, seals, pistons, and other internal components. Precautions are outlined for cleanliness and containing fluids during maintenance.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fsejfksekmmd
The document provides instructions for removing and installing a piston pump (hydrostatic pump) on a 297C Multi Terrain Loader. It describes disconnecting hydraulic lines and electrical connections, then lifting the 73 kg pump from the machine using a special tool. Detailed steps are given for removing mounting bolts and seals, and cleaning components prior to reinstallation. Proper torque specifications are listed for reinstalling the pump.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...uuudfjjdjkskem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...fjjskekskem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...fhshefjjskefkem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h036...fujseskemmesd
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and other technical details. The document contains detailed explanations and examples of using service tools, pressing parts, bolt torque, locks, and working with lines, wires, shims, bearings, gaskets, and batteries during the repair process.
New holland l223 tier 4 skid steer loader service repair manual [ndm474381 ]fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drivetrain, hydraulic and electrical systems, frames, wheels/tracks, cab climate control, front loader/bucket, and other components. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...fujseskemmesd
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries provide the key steps for each procedure, including any required tools and cleaning/lubrication requirements. Detailed illustrations are included to identify the specific components.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
The document provides instructions for installing a transmission on a 428D backhoe loader. It describes using various tools to position the transmission and connect components. Fourteen bolts are installed to secure the transmission to the engine. Electrical connectors and fluid lines are then connected. Finally, inspection plates are installed and tools are removed upon completion.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
1) Removing fuel injection lines, loosening nuts, and removing nozzles and seat washers from the cylinder head.
2) Cleaning threads, installing new seat washers, applying anti-seize compound, positioning nozzles, and tightening nuts to specifications.
3) For fuel injection pumps, it describes removing water pumps, lines, bolts, nuts, and O-rings, using timing pins to ensure correct positioning, and special tools that may be required.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
This document provides instructions for disassembling and assembling the final drive and drive/steering axle housing of a 428D backhoe loader. The disassembly process involves removing snap rings, thrust washers, bearings and seals from the final drive hub. The assembly process describes installing these components in reverse order and adjusting end play.
New holland cx5080 elevation combine harvesters service repair manualfujseskemmesd
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
The document provides disassembly instructions for a 428D backhoe loader transmission. It lists 30 steps to fully disassemble the transmission along with required tools. These steps include removing valve groups, shafts, seals, bearings, gears, and other internal components. Detailed illustrations accompany each step to show how to remove the individual parts in the proper order. Cleanliness is emphasized when disassembling to prevent dirt from entering components.
Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt0...fujseskemmesd
This document provides instructions for removing and disassembling a steering metering pump on a 428D Backhoe Loader. It describes 18 steps to disassemble the pump by removing components like bolts, seals, springs, and fittings. Safety precautions are provided to prevent injury from hydraulic pressure and ensure cleanliness when handling components.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 430 d backhoe loader (prefix bnk) service repair manual (bnk0...fhsjejfsekkkm
The document provides instructions for assembling and installing the transmission on a 430D backhoe loader. It details assembling the various transmission components like bearings, gears, shafts, and cases. It also describes installing the assembled transmission into the vehicle and making final connections. The transmission assembly involves multiple steps of pressing, heating, and inserting components in the correct order.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat 438 d backhoe loader (prefix bpe) service repair manual (bpe0...udfjjjskekdme
The document provides instructions for assembling the transmission of a 438D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, and cases in their proper order. Tools needed for the assembly are listed. Cleanliness is emphasized and components should be cleaned and oiled before installation. Tolerances for shaft play are provided to check proper assembly. The transmission is then installed in the vehicle and filled with the specified oil.
Caterpillar cat 160 k motor grader (prefix szm) service repair manual (szm000...fjjsekkskeoelkm
This document provides instructions for assembling and installing the final drive on a 160K motor grader. The 30-step assembly procedure includes installing bearings, seals, sprockets, housing components, and fasteners in the correct order. Technicians are instructed to clean all parts thoroughly, apply lubricant where specified, and tighten fasteners to the proper torque specifications. The summary concludes by stating the final drives are installed and the tandem housing is attached.
Caterpillar cat 140 m motor grader (prefix b9d) service repair manual (b9d000...ufjjsejfkskemme
This document provides instructions for removing and installing rear gear group components on a 140M Motor Grader. It describes removing the flywheel, gear assembly, bearings, and seals. Detailed steps are provided with accompanying illustrations showing the specific components and tools used. Precautions are outlined such as keeping parts clean and properly installing bearings at the correct angles and distances.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fhsjejfsekkkm
The document provides instructions for assembling and installing a transmission (direct drive) for a 430D backhoe loader. It describes cleaning and lubricating transmission components before assembly. It then provides step-by-step instructions to assemble the transmission case, input shaft, reverse shaft, output shafts, and final assembly. It describes using various tools and heating bearing cones to specified temperatures. Finally, it outlines installing the assembled transmission on the backhoe loader.
Caterpillar cat 287 c multi terrain loader (prefix mas) service repair manual...fujsefkskemm
The document provides instructions for removing and assembling a piston pump (hydrostatic pump) from a 287C Multi Terrain Loader. It describes disconnecting hoses and removing mounting bolts to detach the pump. It then details disassembling the pump by removing bearings, seals, pistons, and other internal components. Finally, it explains testing the reassembled pump before reinstalling it in the vehicle.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fiksejkskeleudk
The document provides instructions for removing and installing a piston pump (hydrostatic) from a 297C Multi Terrain Loader. It describes using lifting equipment to remove the 73 kg pump and disconnecting hydraulic hoses and electrical harnesses. Detailed steps are given to disassemble the pump by removing plates, seals, pistons, and other internal components. Precautions are outlined for cleanliness and containing fluids during maintenance.
Caterpillar cat 297 c multi terrain loader (prefix gcp) service repair manual...fsejfksekmmd
The document provides instructions for removing and installing a piston pump (hydrostatic pump) on a 297C Multi Terrain Loader. It describes disconnecting hydraulic lines and electrical connections, then lifting the 73 kg pump from the machine using a special tool. Detailed steps are given for removing mounting bolts and seals, and cleaning components prior to reinstallation. Proper torque specifications are listed for reinstalling the pump.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...uuudfjjdjkskem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...fjjskekskem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Caterpillar cat 277 c multi terrain loader (prefix jwf) service repair manual...fhshefjjskefkem
The document provides instructions for removing a piston motor from a 277C Multi Terrain Loader. The steps include releasing system pressure, removing the track and track drive, disconnecting hoses and harness assemblies, and using lifting equipment to remove the track drive assembly from the machine. Tools include a link bracket and sleeves for lifting, and the track drive assembly weighs approximately 118 kg.
Similar to Caterpillar cat 287 c multi terrain loader (prefix mas) service repair manual (mas00001 and up) (6)
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h036...fujseskemmesd
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and other technical details. The document contains detailed explanations and examples of using service tools, pressing parts, bolt torque, locks, and working with lines, wires, shims, bearings, gaskets, and batteries during the repair process.
New holland l223 tier 4 skid steer loader service repair manual [ndm474381 ]fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drivetrain, hydraulic and electrical systems, frames, wheels/tracks, cab climate control, front loader/bucket, and other components. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...fujseskemmesd
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries provide the key steps for each procedure, including any required tools and cleaning/lubrication requirements. Detailed illustrations are included to identify the specific components.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
The document provides instructions for installing a transmission on a 428D backhoe loader. It describes using various tools to position the transmission and connect components. Fourteen bolts are installed to secure the transmission to the engine. Electrical connectors and fluid lines are then connected. Finally, inspection plates are installed and tools are removed upon completion.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
1) Removing fuel injection lines, loosening nuts, and removing nozzles and seat washers from the cylinder head.
2) Cleaning threads, installing new seat washers, applying anti-seize compound, positioning nozzles, and tightening nuts to specifications.
3) For fuel injection pumps, it describes removing water pumps, lines, bolts, nuts, and O-rings, using timing pins to ensure correct positioning, and special tools that may be required.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
This document provides instructions for disassembling and assembling the final drive and drive/steering axle housing of a 428D backhoe loader. The disassembly process involves removing snap rings, thrust washers, bearings and seals from the final drive hub. The assembly process describes installing these components in reverse order and adjusting end play.
New holland cx5080 elevation combine harvesters service repair manualfujseskemmesd
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
The document provides disassembly instructions for a 428D backhoe loader transmission. It lists 30 steps to fully disassemble the transmission along with required tools. These steps include removing valve groups, shafts, seals, bearings, gears, and other internal components. Detailed illustrations accompany each step to show how to remove the individual parts in the proper order. Cleanliness is emphasized when disassembling to prevent dirt from entering components.
Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt0...fujseskemmesd
This document provides instructions for removing and disassembling a steering metering pump on a 428D Backhoe Loader. It describes 18 steps to disassemble the pump by removing components like bolts, seals, springs, and fittings. Safety precautions are provided to prevent injury from hydraulic pressure and ensure cleanliness when handling components.
Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt0...fujseskemmesd
The document provides instructions for removing and disassembling the transmission of a 428D backhoe loader. It describes using various tools to support the machine, drain the transmission oil, disconnect electrical connections and hydraulic lines, and remove mounting bolts. The transmission can then be lowered from the machine and further disassembled into its major components on a repair stand, including removing valve groups, sensors, seals, and gaskets. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 428 d backhoe loader (prefix bll) service repair manual (bll0...fujseskemmesd
The document provides instructions for disassembling the transmission of a 428D backhoe loader. It describes removing the transmission from the machine and then disassembling it into its major components. These include removing the case, output shafts on both sides, input shaft, and other internal parts. Detailed steps are given for removing each part, often using specialized tools. Cleanliness is stressed and removal of fluid is described.
New holland cx880 combine harvesters service repair manualfujseskemmesd
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland cx6.90 fpt cursor 9 stage iv combine harvester service repair manualfujseskemmesd
This service manual provides maintenance and repair information for several combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual is divided into sections covering different vehicle systems such as the engine, transmission, hydraulic systems, electrical systems, and attachments. Each section contains technical data, descriptions of system operation, diagnostic procedures, and service instructions.
Caterpillar cat 322 c excavator (prefix fed) service repair manual (fed00001 ...fujseskemmesd
The document provides instructions for disassembling a pilot valve used in Caterpillar 322C and 322C L excavators. It outlines 19 steps to remove components like fittings, seals, covers, bushings and pushrods. Cleanliness is emphasized when disassembling to prevent dirt from entering internal mechanisms. Identification marks are to be placed on components for reassembly. Personal protective equipment is recommended when releasing spring forces during disassembly.
New holland cr980 combine harvesters service repair manualfujseskemmesd
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electronics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
Caterpillar cat 322 c excavator (prefix bgr) service repair manual (bgr00001 ...fujseskemmesd
This document provides instructions for disassembling the control valve and auxiliary control valve on a 322C excavator. It describes removing various components like solenoid valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contaminating the hydraulic system. The multi-step process includes removing bolts, plugs, springs and O-rings from components like the valve housing, spool and relief valves.
New holland c238 tier 4 compact track loader service repair manual [ncm425510...fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drive systems, brakes, hydraulics, frames, wheels/tracks, climate control, electrical systems, front loader/bucket, cab, and decals. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 320 c ln 320cln excavator (prefix bcn) service repair manual ...fujseskemmesd
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Caterpillar cat 320 c l excavator (prefix amc) service repair manual (amc0000...fujseskemmesd
This document provides instructions for removing and installing various components of the heating, ventilation, and air conditioning (HVAC) system on a 320C excavator, including:
1) Actuator motors for different air dampers and controls.
2) The fan speed control component.
3) The ambient air temperature sensor.
Detailed step-by-step procedures are provided with accompanying illustrations for each removal and installation process. Safety precautions and proper alignment of linkages are emphasized.
Case ih stx425 steiger tractor service repair manual pin jee0102001 and afterfujseskemmesd
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287C MULTI TERRAIN LOADER MAS
Configuration: 287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C
Multi Terrain Loaders Power Train
Media Number -KENR5197-07 Publication Date -01/06/2014 Date Updated -10/06/2014
i06660138
Piston Pump (Hydrostatic) - Assemble
SMCS - 5070-016-H7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
D 1P-1859 Retaining Ring Pliers 1
E 9S-3263 Thread Lock Compound 1
1/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06063261
1. Raise the temperature of bearing (42).
2. Install bearing (42).
3. Use Tooling (D) to install retaining ring (43).
4. Install shaft assembly (40) and seal (44).
5. Install O-ring seal (45).
6. Install plate (46).
7. Install retaining ring (47).
2/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01326183
8. Raise the temperature of bearing (33).
9. Install bearing (33) onto shaft (32).
Illustration 3 g01325554
10. Install shaft (32).
Illustration 4 g01325550
11. Install bearings (31) onto swashplate (28).
3/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01325548
12. Install seals (29) and block (30).
Illustration 6 g01325546
13. Install piston assembly (27) and swashplate (28).
Illustration 7 g01325544
14. Install O-ring seal (26).
Illustration 8 g01325542
4/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 15. Install set screw (23). Apply slight pressure to the piston assembly.
16. Repeat Step 15 for the opposite side.
17. Use a suitable measuring device to center the swashplate. Measure the distance that is from
the machined face of the housing to both sides of the swashplate. Adjust setscrews (23) to
achieve the same distance to the swashplate.
18. Install retainer (24), and bolts (25).
Illustration 9 g06063253
19. Install barrel assembly (40).
Illustration 10 g06063248
5/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g06063242
20. Install bearings (39).
21. Install port plate (36) and gasket (35).
22. Install head (38).
23. Install coupling (37).
Illustration 12 g01325564
24. Repeat Steps16 through Steps 23 for barrel assembly (34).
25. Install barrel assembly (34).
Illustration 13 g01325541
26. Install housing (22) and bolts (21). Tighten bolts (21) to a torque of 110 ± 10 N·m
(81 ± 7 lb ft).
6/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g01377507
Illustration 15 g01377504
27. Install crossover relief valves (14B), backup ring (14D), O-ring seal (14C), O-ring seal
(14E) and plugs (14A) into the head.
Illustration 16 g01325540
28. Install O-ring seal (20), backup ring (19), and O-ring seal (18).
7/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g01325538
29. Install O-ring seals (17), backup rings (16), and O-ring seal (15).
Illustration 18 g01325536
30. Install valve (11). Tighten valve (11) to a torque of 44 ± 3 N·m (32 ± 2 lb ft).
31. Install cartridge (14), coil (12), and nut (13). Tighten nut (13) to a torque of 80 ± 10 N·m
(59 ± 7 lb ft).
32. Install the cross over relief valves and the plugs into the head. Tighten plugs (21) to a torque
of 110 ± 10 N·m (81 ± 7 lb ft).
Illustration 19 g01377500
8/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 33. Install screen (6A).
Illustration 20 g01325526
34. Install cartridge (6), bolts (5), coil (4), the O-ring seal, and nut (3). Tighten bolts (5) to a
torque of 5.5 ± 0.1 N·m (49 ± 0.9 lb in).
Illustration 21 g01325527
35. Install control arm (8) and gasket (7).
36. Apply Tooling (E) to control arm (8).
9/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g01325534
37. Install valve (10) and bolts (9). Tighten bolts (9) to a torque of 13 ± 1 N·m (115 ± 9 lb in).
Illustration 23 g01325524
38. Repeat Steps 34 through Steps 35 for valve (2).
39. Install bolts (1) and valve (2). Tighten bolts (1) to a torque of 13 ± 1 N·m (115 ± 9 lb in).
40. Bench test the pump before installation into the machine.
End By:
a. Install the pump. Refer to Disassembly and Assembly, "Piston Pump (Hydrostatic) -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 17:56:21 UTC+0800 2019
10/10287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C E...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287C MULTI TERRAIN LOADER MAS
Configuration: 287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C
Multi Terrain Loaders Power Train
Media Number -KENR5197-07 Publication Date -01/06/2014 Date Updated -10/06/2014
i07466134
Piston Pump (Hydrostatic) - Install
SMCS - 5070-012-H7
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
247-4296 Pump Removal Handle As 1
FT-2999 Weight 2
FT-2998 Lock Collar 2
138-7575 Link Bracket 1
B
159-3327 Wrench Adapter(1)
1
387-9124 Wrench Adapter(2)
1
C 1P-1857 Retaining Ring Pliers 1
D 9S-3263 Thread Lock Compound 1
(1)
For use on 21mm head bolts.
(2)
For use on 14mm head bolts.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
1/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01342687
Illustration 2 g01342689
2/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 1. Install coupling (13). Use Tooling (C) to install retaining ring (12). Apply Tooling (D) to
the threads of bolt (11). Install bolts (11). Tighten bolts (11) to a torque of 102 ± 5 N·m
(75 ± 4 lb ft).
Illustration 3 g01342634
Illustration 4 g01342641
2. Attach Tooling (A) and a suitable lifting device to piston pump (9). The weight of piston
pump (9) is approximately 73 kg (160 lb). Use Tooling (A) and the suitable lifting device to
position piston pump (9) to the machine.
Note: Ensure that the splines are properly aligned with the engine.
3. Use Tooling (B) to install bolts (10) to piston pump (9).
4. Connect harness assemblies (8).
3/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g01342576
5. Position plate assembly (6) and install bolts (7).
6. Connect tube assembly (5).
7. Connect hose assembly (1).
8. Connect hose assemblies (3).
9. Connect hose (4).
10. Connect hose assembly (2).
End By:
a. Install the high flow piston pump. Refer to Disassembly and Assembly, "Piston Pump -
Install".
b. Install the hydraulic tank. Refer to Disassembly and Assembly, "Hydraulic Tank - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 17:57:17 UTC+0800 2019
4/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287C MULTI TERRAIN LOADER MAS
Configuration: 287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C
Multi Terrain Loaders Power Train
Media Number -KENR5197-07 Publication Date -01/06/2014 Date Updated -10/06/2014
i02662132
Piston Motor (Hydrostatic) - Remove
SMCS - 4351-011
S/N - GCP1-UP
S/N - JWF1-UP
S/N - MAS1-UP
S/N - MET1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 140-7742 Sleeve 2
Start By:
a. Relieve the hydraulic system pressure. Refer to Disassembly and Assembly, "System
Pressure - Release".
b. Remove the track. Refer to Disassembly and Assembly, "Track (Rubber) - Remove and
Install".
c. Remove the track drive. Refer to Disassembly and Assembly, "Track Drive - Remove".
1/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Note: Put identification marks on all hoses, on all hose assemblies, and on all harness assemblies
for installation purposes. Plug all hose assemblies. This helps to prevent fluid loss, and this helps
to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01337540
1. Attach Tooling (A) to track drive assembly (1). The weight of track drive assembly (1) is
approximately 118 kg (260 lb).
2. Remove bolt (3) and position track tensioner (2) out of the way.
2/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01337558
3. Remove bolts (4) and bolt (5). Remove retainer (6).
Illustration 3 g01337566
4. Disconnect harness assembly (7).
5. Disconnect hose assemblies (8).
6. Disconnect hose assemblies (9).
7. Disconnect hose assemblies (10).
8. Use Tooling (A) and the suitable lifting device in order to remove track drive assembly (1)
from the machine.
3/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 4 g01337587
Note: Note the orientation of motor support (11) to piston motor (13) for assembly
purposes.
9. Attach Tooling (B) and a suitable lifting device to motor support (11). The weight of motor
support (11) is approximately 54 kg (120 lb).
10. Remove bolts (12).
11. Use the suitable lifting device and Tooling (B) in order to remove motor support (11) from
piston motor (13).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 17:58:13 UTC+0800 2019
4/4287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287C MULTI TERRAIN LOADER MAS
Configuration: 287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C
Multi Terrain Loaders Power Train
Media Number -KENR5197-07 Publication Date -01/06/2014 Date Updated -10/06/2014
i04281771
Piston Motor (Hydrostatic) - Disassemble
SMCS - 4351-015
S/N - GCP1-UP
S/N - JWF1-UP
S/N - MAS1-UP
S/N - MET1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 136-1452 Retaining Ring Pliers As 1
C
1P-0074 Slide Hammer Puller Gp 1
5F-7340 Adapter 1
5F-7342 Adapter 1
D 1P-1859 Retaining Ring Pliers 1
E 5P-5197 Retaining Ring Pliers As 1
F FT-3081 Adapter Plate 1
G 127-8458 Final Drive Bench AR 1
1/15287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. H 308-5676 Spanner Wrench Assembly 1
J 1H-3110 Bearing Puller Gp 1
K 5F-7343 Bearing Puller Gp 1
Start By:
a. Remove the piston motor.
Illustration 1 g01344079
1. Remove bolts (1) and cover (2).
Illustration 2 g01344080
2. Remove O-ring seal (3).
2/15287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g01345109
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove bolts (4) and head (5).
Illustration 4 g01345111
4. Remove O-ring seals (6), port plate (7), and bearing (8).
3/15287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 5 g01345112
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove plug (9).
Illustration 6 g01345113
6. Remove O-ring seal (12) from plug (9).
7. Remove spring (11) and piston (10).
8. Repeat Step 6 for the opposite side.
4/15287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 7 g01345114
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (13), the O-ring seal, and spring (14).
10. Remove plug (17), the O-ring seal, spring (16), and spool (15).
5/15287C Multi Terrain Loader MAS00001-UP (MACHINE) POWERED BY 3044C Engi...
2019/10/16https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...