This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar 249D compact track loaders. The procedures describe using various tools to compress springs, remove bolts and nuts, and install new gaskets and components. Safety notices are included to warn technicians to keep parts clean, plug openings, and wear protective equipment when working with compressed springs.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fusjezsfkskefmsme
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, seals, and keepers, while taking precautions to prevent damage and entry of loose parts into the engine. Detailed illustrations supplement the text instructions.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fjjskefkskem
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, springs, and seals. Safety notices are provided regarding keeping parts clean, plugging openings to prevent loose parts from entering the engine, and ensuring compressed springs are released safely.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal process involves loosening fasteners, removing nuts/bolts, and removing the manifold and gasket. The installation process involves cleaning surfaces, installing a new gasket, aligning and installing the manifold, and tightening fasteners to the specified torque. Safety notices are provided throughout regarding keeping parts clean and preventing loose parts from entering the engine.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a Caterpillar 216B3 Skid Steer Loader. The removal procedure involves loosening nuts and bolts to detach the exhaust manifold, then removing studs, gaskets and manifolds. Installation is the reverse, ensuring clean surfaces and proper torque of fasteners. Valve removal requires compressing springs with a tool and removing keepers and springs, while installation compresses springs to replace keepers.
This document provides instructions for removing and installing exhaust manifolds on Caterpillar C1.1, C1.5, and C2.2 engines. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. Installation involves cleaning surfaces, installing a new gasket and exhaust manifold, and tightening fasteners to the specified torque. Instructions are also provided for removing and installing inlet and exhaust valve springs while the cylinder head is still installed on the engine.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a Caterpillar 216B3 Skid Steer Loader. The removal procedure involves loosening nuts and bolts to detach the exhaust manifold, then removing studs, gaskets and manifolds. Installation is the reverse, ensuring clean surfaces and proper torque of fasteners. Valve removal requires compressing springs with a tool and removing keepers and springs, while installation compresses springs to replace keepers.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fusjezsfkskefmsme
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, seals, and keepers, while taking precautions to prevent damage and entry of loose parts into the engine. Detailed illustrations supplement the text instructions.
Caterpillar cat 249 d compact track loader (prefix ah9) service repair manual...fjjskefkskem
This document provides instructions for removing and installing exhaust manifolds, inlet and exhaust valves, and inlet and exhaust valve springs on Caterpillar C1.1, C1.5, and C2.2 engines. The procedures describe using various tools to compress springs, remove and install components like manifolds, valves, springs, and seals. Safety notices are provided regarding keeping parts clean, plugging openings to prevent loose parts from entering the engine, and ensuring compressed springs are released safely.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket. The installation procedure involves cleaning surfaces, installing a new gasket, aligning and installing the exhaust manifold, and tightening fasteners to the specified torque. Safety notices are provided regarding keeping parts clean and preventing damage.
The document provides instructions for removing and installing an exhaust manifold on a 216B3 Skid Steer Loader with a C2.2 engine. The removal process involves loosening fasteners, removing nuts/bolts, and removing the manifold and gasket. The installation process involves cleaning surfaces, installing a new gasket, aligning and installing the manifold, and tightening fasteners to the specified torque. Safety notices are provided throughout regarding keeping parts clean and preventing loose parts from entering the engine.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a Caterpillar 216B3 Skid Steer Loader. The removal procedure involves loosening nuts and bolts to detach the exhaust manifold, then removing studs, gaskets and manifolds. Installation is the reverse, ensuring clean surfaces and proper torque of fasteners. Valve removal requires compressing springs with a tool and removing keepers and springs, while installation compresses springs to replace keepers.
This document provides instructions for removing and installing exhaust manifolds on Caterpillar C1.1, C1.5, and C2.2 engines. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. Installation involves cleaning surfaces, installing a new gasket and exhaust manifold, and tightening fasteners to the specified torque. Instructions are also provided for removing and installing inlet and exhaust valve springs while the cylinder head is still installed on the engine.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a Caterpillar 216B3 Skid Steer Loader. The removal procedure involves loosening nuts and bolts to detach the exhaust manifold, then removing studs, gaskets and manifolds. Installation is the reverse, ensuring clean surfaces and proper torque of fasteners. Valve removal requires compressing springs with a tool and removing keepers and springs, while installation compresses springs to replace keepers.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...soeldksejdksem
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. The procedure involves using specialized tools to compress the valve springs so that the valves, retainers, and springs can be safely accessed and removed one at a time. Proper cleaning and inspection of parts is emphasized. The installation procedure specifies cleaning and inspecting all cylinder head components before reassembling the valves, springs, and related parts in their proper positions and orientations.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...fjskksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar C6.4 engine. The procedure involves using specialized tools to remove the valves, electronic unit injectors, and valve guides from the cylinder head. Cleanliness is emphasized to prevent contaminating parts. The installation procedure specifies lubricating valve stems before reinstalling the valves, guides, and other components in the reverse order of removal. Safety notices warn of risks such as being struck by parts or fluids and provide guidance on containment and disposal.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...ufjjsjekksemmd
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the valve springs and remove the valves. It also explains how to remove and install valve guides using appropriate driver kits and reamers. Clearances for valve stems, guides, and replacement specifications are provided.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjjskekfsem
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D skid steer loader. It describes the required tools and multi-step process, which involves using a valve spring compressor to position the piston and safely remove the valve spring. Safety precautions are noted. Similar procedures are provided for removing the valve springs from a cylinder head removed from the engine, and for removing and installing valve guides.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine. The procedure involves using special tools to compress the valve springs, remove the retainers and springs, and then install new springs and retainers. Safety precautions are outlined to prevent injury from the force of compressed springs. The process is also described for removing and installing the valves from the cylinder head.
- The document provides instructions for removing and installing inlet and exhaust valve springs on a 320D2 excavator engine.
- Special tools are required to safely compress the valve springs and tools are used to ensure the piston is at top dead center before removing springs.
- The procedure involves identifying valves, compressing springs, removing retainers and springs, then reversing the process for installation.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine. The procedure involves using special tools to compress the valve springs, remove the retainers and springs, and then install new springs and retainers. Safety precautions are outlined to prevent injury from the force of compressed springs. The process is also described for removing and installing the valves from the cylinder head.
- The document provides instructions for removing and installing inlet and exhaust valve springs on a 320D2 excavator engine.
- Special tools are required to safely compress the valve springs and tools are used to ensure the piston is at top dead center before removing springs.
- The procedure involves identifying valves, compressing springs, removing retainers and springs, then reversing the process for installation.
This document provides instructions for removing and installing fuel lines, filters, pumps, and electronic unit injectors on a C32 industrial engine. Key steps include:
- Marking fuel lines before removal and checking for damage before reinstalling new lines, ensuring proper clearance from other components.
- Removing the fuel filter and water separator by disconnecting hoses and harness, and installing a new filter on the cleaned base assembly.
- Removing the fuel transfer pump by disconnecting hoses and bolts, and installing with a new O-ring and reconnecting hoses.
- Removing electronic unit injectors after disconnecting harnesses and bridges by prying them out, and installing by cleaning the cylinders
This document provides instructions for removing and installing various fuel system components on a Caterpillar C32 Industrial Engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel lines
- Fuel transfer pump
- Fuel pressure regulator
- Exhaust cooler
The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing components in reverse order, noting specific torque specifications for fasteners. Safety precautions are provided for containing fluids and releasing spring pressure.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C32 Industrial Engine BT4, including:
- The fuel priming pump, fuel filter base, fuel lines, fuel transfer pump, and fuel pressure regulator.
- Detailed steps are given for each component's removal and installation, including required tools. Safety precautions are provided, such as containing fluids and ensuring fuel system is shut off.
- Illustrations supplement the text instructions to show part locations and orientations. Torque specifications are listed for reinstallation.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the vibration damper and pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front gear group.
- Removing and installing the front housing.
- Removing and installing brackets and pulleys for the accessory drive.
- Removing and installing the fumes disposal filter.
- Removing and installing the valve mechanism cover.
Step-by-step instructions are provided for each procedure, including any required tools and tightening specifications.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are accompanied by illustrations and require the use of various tools.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the cylinder block using a lifting device.
2. Inspecting the crankshaft rear seal for leaks and cleaning the housing before installation.
3. Installing the housing onto the cylinder block using guide studs, bolts, and checking alignment with a dial indicator.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of the removal steps.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...itj79143591
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the housing to access the internal components.
More Related Content
Similar to Caterpillar Cat 249D Compact Track Loader (Prefix AH9) Service Repair Manual (AH900001 and up).pdf
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...soeldksejdksem
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. The procedure involves using specialized tools to compress the valve springs so that the valves, retainers, and springs can be safely accessed and removed one at a time. Proper cleaning and inspection of parts is emphasized. The installation procedure specifies cleaning and inspecting all cylinder head components before reassembling the valves, springs, and related parts in their proper positions and orientations.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...fjskksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar C6.4 engine. The procedure involves using specialized tools to remove the valves, electronic unit injectors, and valve guides from the cylinder head. Cleanliness is emphasized to prevent contaminating parts. The installation procedure specifies lubricating valve stems before reinstalling the valves, guides, and other components in the reverse order of removal. Safety notices warn of risks such as being struck by parts or fluids and provide guidance on containment and disposal.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...ufjjsjekksemmd
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the valve springs and remove the valves. It also explains how to remove and install valve guides using appropriate driver kits and reamers. Clearances for valve stems, guides, and replacement specifications are provided.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjjskekfsem
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D skid steer loader. It describes the required tools and multi-step process, which involves using a valve spring compressor to position the piston and safely remove the valve spring. Safety precautions are noted. Similar procedures are provided for removing the valve springs from a cylinder head removed from the engine, and for removing and installing valve guides.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine. The procedure involves using special tools to compress the valve springs, remove the retainers and springs, and then install new springs and retainers. Safety precautions are outlined to prevent injury from the force of compressed springs. The process is also described for removing and installing the valves from the cylinder head.
- The document provides instructions for removing and installing inlet and exhaust valve springs on a 320D2 excavator engine.
- Special tools are required to safely compress the valve springs and tools are used to ensure the piston is at top dead center before removing springs.
- The procedure involves identifying valves, compressing springs, removing retainers and springs, then reversing the process for installation.
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D2 excavator engine. The procedure involves using special tools to compress the valve springs, remove the retainers and springs, and then install new springs and retainers. Safety precautions are outlined to prevent injury from the force of compressed springs. The process is also described for removing and installing the valves from the cylinder head.
- The document provides instructions for removing and installing inlet and exhaust valve springs on a 320D2 excavator engine.
- Special tools are required to safely compress the valve springs and tools are used to ensure the piston is at top dead center before removing springs.
- The procedure involves identifying valves, compressing springs, removing retainers and springs, then reversing the process for installation.
Similar to Caterpillar Cat 249D Compact Track Loader (Prefix AH9) Service Repair Manual (AH900001 and up).pdf (10)
This document provides instructions for removing and installing fuel lines, filters, pumps, and electronic unit injectors on a C32 industrial engine. Key steps include:
- Marking fuel lines before removal and checking for damage before reinstalling new lines, ensuring proper clearance from other components.
- Removing the fuel filter and water separator by disconnecting hoses and harness, and installing a new filter on the cleaned base assembly.
- Removing the fuel transfer pump by disconnecting hoses and bolts, and installing with a new O-ring and reconnecting hoses.
- Removing electronic unit injectors after disconnecting harnesses and bridges by prying them out, and installing by cleaning the cylinders
This document provides instructions for removing and installing various fuel system components on a Caterpillar C32 Industrial Engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel lines
- Fuel transfer pump
- Fuel pressure regulator
- Exhaust cooler
The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing components in reverse order, noting specific torque specifications for fasteners. Safety precautions are provided for containing fluids and releasing spring pressure.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C32 Industrial Engine BT4, including:
- The fuel priming pump, fuel filter base, fuel lines, fuel transfer pump, and fuel pressure regulator.
- Detailed steps are given for each component's removal and installation, including required tools. Safety precautions are provided, such as containing fluids and ensuring fuel system is shut off.
- Illustrations supplement the text instructions to show part locations and orientations. Torque specifications are listed for reinstallation.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the vibration damper and pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front gear group.
- Removing and installing the front housing.
- Removing and installing brackets and pulleys for the accessory drive.
- Removing and installing the fumes disposal filter.
- Removing and installing the valve mechanism cover.
Step-by-step instructions are provided for each procedure, including any required tools and tightening specifications.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are accompanied by illustrations and require the use of various tools.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the cylinder block using a lifting device.
2. Inspecting the crankshaft rear seal for leaks and cleaning the housing before installation.
3. Installing the housing onto the cylinder block using guide studs, bolts, and checking alignment with a dial indicator.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of the removal steps.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...itj79143591
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the housing to access the internal components.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1) Draining the engine coolant below the level of the regulator.
2) Disconnecting the hose from the regulator cover and removing mounting bolts.
3) Cleaning and installing a new O-ring, then reversing the removal steps to reinstall the regulator.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...itj79143591
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...itj79143591
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting lines. Disassembly separates housing components. Assembly reconnects parts and installation bolts the turbocharger back into place.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...itj79143591
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...itj79143591
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure instructs to drill holes in the existing seal and use a slide hammer puller to remove it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning of parts and use of retaining compound is emphasized.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...itj79143591
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the flywheel. Precautions are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 249D COMPACT TRACK LOADER AH9
Configuration: 249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i07360106
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
a. If the engine is equipped with a turbocharger, remove the turbocharger. Refer to
Disassembly and Assembly, "Turbocharger - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The three cylinder and the four cylinder engines have different exhaust manifolds. The
removal procedure is similar for all models.
1/3
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01326567
Typical example
1. Loosen nuts (5) and bolts (6).
Note: To prevent distortion of the exhaust manifold, loosen the outer fasteners first.
2. Remove nuts (5) and bolts (6).
Note: Identify bolts of different lengths so that the bolts can be installed in the correct
positions.
3. Remove exhaust manifold (4) from cylinder head (1). Note the orientation of the exhaust
manifold for installation.
4. Remove gasket (3) from cylinder head (1).
5. If necessary, remove exhaust manifold studs (2) from cylinder head (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The three cylinder and the four cylinder engines have different exhaust manifolds. The
installation procedure is similar for all models.
2/3
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Ensure that the mating surfaces of the cylinder head and the exhaust manifold are clean and
free from damage.
Illustration 2 g01326567
Typical example
2. If necessary, install exhaust manifold studs (2) to cylinder head (1).
3. Install a new exhaust manifold gasket (3) to cylinder head (1).
4. Align exhaust manifold (4) with studs (2) and install the exhaust manifold to cylinder head
(1).
Note: Ensure that the exhaust manifold is installed in the correct orientation.
5. Install nuts (5) and bolts (6) finger tight.
Note: Ensure that bolts of different lengths are installed in the correct positions.
6. For the C1.1 and C1.5 engines, tighten nuts (5) and bolts (6) to a torque of 10 N·m
(89 lb in).
For the C2.2 engine, tighten nuts (5) and bolts (6) to a torque of 25 N·m (18 lb ft).
Note: Tighten the inner bolts first.
End By:
a. If the engine is equipped with a turbocharger, install the turbocharger. Refer to Disassembly
and Assembly, "Turbocharger - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 19 22:58:33 UTC+0800 2019
3/3
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 249D COMPACT TRACK LOADER AH9
Configuration: 249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i07360109
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B(1)
268-1969 Adapter 1
B(2)
9U-6194 Adapter 1
(1)
C1.1 engine
(2)
C1.5 and C2.2 engines
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Install suitable plugs to the inlet ports of the cylinder head in order to
prevent the entry of loose parts into the engine.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Note: The removal procedure is similar for the three cylinder and the four cylinder engines. The
following procedure should be adopted to remove the valve springs when the cylinder head is
installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove
and Install" for the procedure to remove the valve springs from a cylinder head that has been
removed from the engine.
Note: Ensure that the appropriate piston is at the top center position before the valve spring is
removed. Failure to ensure that the piston is at the top center position may allow the valve to drop
into the cylinder bore.
2/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01304583
Typical example
1. Follow Steps 1.a through 1.d to position the appropriate piston at top center.
a. Install Tooling (A) and (B) in position on the cylinder head to compress a valve
spring for the appropriate piston.
b. Use Tooling (A) to compress valve spring (3) and open the valve slightly.
Note: Do not compress the spring so that the valve spring retainer (2) touches the
valve stem seal.
c. Carefully rotate the crankshaft until the piston touches the valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in
bent valve stems.
d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A)
until the piston is at the top center position. The valve is now held in a position that
allows the valve spring to be safely removed.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2. Use tool (A) to compress valve spring (3). Remove valve keepers (1).
Note: For four cylinder engines, if all valve springs require replacement the procedure can
be carried out on two cylinders at the same time. The procedure can be carried out on the
3/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all the valve springs are
installed before changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
3. Apply sufficient pressure to Tooling (A) to allow removal of the valve keepers (1).
Note: Do not compress the spring so that the valve spring retainer (2) touches the valve
stem seal.
Remove valve keepers (1).
4. Slowly release the pressure on Tooling (A).
5. Remove valve spring retainer (2) and remove valve spring (3).
6. Remove Tooling (A) and (B).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B(1)
268-1969 Adapter 1
B(2)
9U-6194 Adapter 1
(1)
C1.1 engine
(2)
C1.5 and C2.2 engines
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
4/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
NOTICE
Install suitable plugs to the inlet ports of the cylinder head in order to
prevent the entry of loose parts into the engine.
1. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder Head
Valves".
Illustration 2 g01304583
Typical example
2. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) onto valve
spring (3).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
3. Install Tooling (A) and (B) in the appropriate position on the cylinder head to compress the
valve spring.
4. Apply sufficient pressure to Tooling (A) to install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches the valve stem
seal.
Install the valve spring keepers.
5. Carefully release the pressure on Tooling (A).
Note: Ensure that the valve keepers are correctly seated.
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
6. Remove Tooling (A). Ensure that all the valves are secured in place by a valve spring and
valve keepers. Rotate the crankshaft through about 45 degrees to clear the piston from the
valve. Lightly strike the top of the valve with a soft hammer to ensure that the valve keepers
are properly installed.
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 19 22:59:28 UTC+0800 2019
6/6
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 249D COMPACT TRACK LOADER AH9
Configuration: 249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i06720078
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The removal procedure is identical for the three cylinder and the four cylinder engines. The
Illustrations show a four cylinder engine.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Place a temporary identification mark on the heads of the valves to identify the correct
position.
Note: Do not stamp the heads of the valves. Stamping or punching the heads of the valves
could cause the valves to fracture.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01315963
Typical example
3/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01325840
Typical example
3. Use Tooling (A) to compress the appropriate valve spring (3). Remove valve keepers (1).
Note: Do not compress the valve spring so that valve spring retainer (2) touches valve stem
seal (4).
4. Remove Tooling (A).
5. Remove valve spring retainer (2). Remove valve spring (3).
6. Remove valve (5).
7. Remove valve stem seal (4).
8. Repeat Steps 3 to 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
4/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. B 256-4865 Valve Stem Seal Replacer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The installation procedure is identical for the three cylinder and the four cylinder engines.
The Illustrations show a four cylinder engine.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.e to inspect the components of the cylinder head assembly. Replace any
components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Systems Operation,
Testing and Adjusting, "Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Systems Operation, Testing and Adjusting, "Valve Guide -
Inspect" for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves".
e. Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder
Head Valves".
5/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g01315893
Typical example
2. Use Tooling (B) to install new valve stem seals (4) onto each of the valve guides.
Note: The outer face of the valve guides must be clean and dry before installing the valve
stem seals.
6/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01325840
Typical example
3. Lubricate the stem of valve (5) with clean engine oil. Install valve (5) in the appropriate
position in the cylinder head. Check the depth of the valve below the face of the cylinder
head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
4. Install valve spring (3) to the cylinder head. Position valve spring retainer (2) onto valve
spring (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
Illustration 5 g01315963
Typical example
5. Use Tooling (A) to compress valve spring (3). Install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
8/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 6. Remove Tooling (A).
7. Repeat Steps 4 to 6 for the remaining valves.
8. Place the cylinder head on a suitable support. Ensure that the heads of the valves are not
obstructed. Gently strike the top of the valves with a soft hammer to ensure that valve
keepers (1) are properly installed.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 19 23:00:24 UTC+0800 2019
9/9
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 249D COMPACT TRACK LOADER AH9
Configuration: 249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i07360118
Engine Oil Line - Remove and Install
SMCS - 1307-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/5
249D Compact Track Loader AH900001-UP (MACHINE) POWERED BY C2.2 Engi...
2019/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...