This document provides instructions for removing and installing the lift cylinder on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, disconnecting hoses and removing pins and bolts to detach the cylinder. Reinstallation is the reverse of removal. Torque specifications are provided for reassembly.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...fjjskekfsem
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...ujfjjsjekkmsmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...fjsjefskekfmme
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, loosening clamps, removing pins and bolts to detach the cylinder and lift arm assemblies. The installation procedure specifies lubricating seals before reattaching the components in reverse order. Torque specifications are provided for reinstallation.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...ujfdjdjfkjksk
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...xiapokang564341
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting devices to raise and lower the lift arms for removal and installation of pins and tubes.
4. Ensuring proper lubrication and torque specifications are followed during reinstallation.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...hvy7sbkw8e
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting devices to raise and lower the lift arms for removal and installation of pins and tubes.
4. Ensuring proper lubrication and torque specifications are followed during reinstallation.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...wenxian17880
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting slings and a lifting device to raise and lower the lift arms for removal and installation of pins and tubes.
4. Reattaching the lift cylinder and ensuring proper torque on all fasteners before refilling hydraulic fluid. Safety precautions are provided throughout.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...jfksemmdm3e
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It describes required tools, safety procedures, and step-by-step instructions for disconnecting hydraulic lines and hoses, removing mounting bolts, and disassembling the cylinders. Cleanliness is emphasized during disassembly and assembly to prevent contamination. Torque specifications and lubrication points are provided.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...fjjskekfsem
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...ujfjjsjekkmsmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...fjsjefskekfmme
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, loosening clamps, removing pins and bolts to detach the cylinder and lift arm assemblies. The installation procedure specifies lubricating seals before reattaching the components in reverse order. Torque specifications are provided for reinstallation.
Caterpillar cat 247 multi terrain loader (prefix cml) service repair manual (...ujfdjdjfkjksk
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include releasing hydraulic pressure, removing pins and bolts to detach components, and installing components in the reverse order while torquing bolts to the specified values. Tools required include retaining ring pliers, seal picks, and molybdenum grease. Safety precautions are provided to relieve hydraulic pressure before disassembly and contain fluids properly.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...xiapokang564341
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting devices to raise and lower the lift arms for removal and installation of pins and tubes.
4. Ensuring proper lubrication and torque specifications are followed during reinstallation.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...hvy7sbkw8e
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting devices to raise and lower the lift arms for removal and installation of pins and tubes.
4. Ensuring proper lubrication and torque specifications are followed during reinstallation.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...wenxian17880
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. Key steps include:
1. Relieving hydraulic pressure before removal or disassembly.
2. Removing pins, bolts, and tubes to detach the lift cylinder from the lift arm.
3. Using lifting slings and a lifting device to raise and lower the lift arms for removal and installation of pins and tubes.
4. Reattaching the lift cylinder and ensuring proper torque on all fasteners before refilling hydraulic fluid. Safety precautions are provided throughout.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...jfksemmdm3e
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It describes required tools, safety procedures, and step-by-step instructions for disconnecting hydraulic lines and hoses, removing mounting bolts, and disassembling the cylinders. Cleanliness is emphasized during disassembly and assembly to prevent contamination. Torque specifications and lubrication points are provided.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...f8isekdodkdmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Tools and torque specifications are provided for disassembly and reassembly. Safety precautions are outlined, such as ensuring all pressure is relieved before disassembling cylinders.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...jkdkkdsmmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve trapped pressure before disassembly and ensure cleanliness of components.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...idksmmdmdm
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It describes required tools, safety procedures, and step-by-step instructions for disassembly and assembly. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and caps, and installing new seals and bearings before reversing the removal process. Proper cleanliness and lubrication are emphasized throughout.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...hean57759707
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It includes safety information and outlines the required tools. The removal process involves releasing system pressure, disconnecting hoses, and removing mounting bolts. The installation is the reverse of removal. Disassembly and cleaning of internal parts is also described.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...fuskddmmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Tools and torque specifications are listed to correctly perform the work. Safety precautions are provided regarding relieving pressure, containing fluids, and preventing contamination.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...jfjkskemem
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a Caterpillar 140M motor grader. Key steps include releasing system pressure, disconnecting hydraulic hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve pressure before disassembly and contain fluids properly during maintenance.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...ufdjskeksmemzx
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It details required tools, safety procedures, and step-by-step instructions for disassembly and reassembly. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and caps, and installing new seals and bearings before reversing the removal process. Proper cleanliness and lubrication of parts is emphasized.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...fiksfejjsekkmme
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a Caterpillar 140M motor grader. Key steps include releasing system pressure, disconnecting hydraulic hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve pressure before disassembly and contain fluids properly during maintenance.
Caterpillar Cat 160M Motor Grader (Prefix B9E) Service Repair Manual (B9E0000...jfksemmdm3e
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 160M Motor Grader. It lists the required tools and safety precautions. The procedures include releasing system pressure, disconnecting hoses, removing mounting bolts, and inspecting and reinstalling components with new seals and bearings as needed. Cleanliness and applying the proper lubricants are emphasized during assembly.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
More Related Content
Similar to Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (CML00001 and up).pdf
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...f8isekdodkdmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Tools and torque specifications are provided for disassembly and reassembly. Safety precautions are outlined, such as ensuring all pressure is relieved before disassembling cylinders.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...jkdkkdsmmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve trapped pressure before disassembly and ensure cleanliness of components.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...idksmmdmdm
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It describes required tools, safety procedures, and step-by-step instructions for disassembly and assembly. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and caps, and installing new seals and bearings before reversing the removal process. Proper cleanliness and lubrication are emphasized throughout.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual Instant ...hean57759707
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It includes safety information and outlines the required tools. The removal process involves releasing system pressure, disconnecting hoses, and removing mounting bolts. The installation is the reverse of removal. Disassembly and cleaning of internal parts is also described.
Caterpillar Cat 140M MOTOR GRADER (Prefix B9G) Service Repair Manual (B9G0000...fuskddmmd
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Tools and torque specifications are listed to correctly perform the work. Safety precautions are provided regarding relieving pressure, containing fluids, and preventing contamination.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...jfjkskemem
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a Caterpillar 140M motor grader. Key steps include releasing system pressure, disconnecting hydraulic hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve pressure before disassembly and contain fluids properly during maintenance.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...ufdjskeksmemzx
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 140M Motor Grader. It details required tools, safety procedures, and step-by-step instructions for disassembly and reassembly. Key steps include releasing system pressure, disconnecting hoses, removing mounting bolts and caps, and installing new seals and bearings before reversing the removal process. Proper cleanliness and lubrication of parts is emphasized.
Caterpillar cat 140 m motor grader (prefix b9g) service repair manual (b9g000...fiksfejjsekkmme
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a Caterpillar 140M motor grader. Key steps include releasing system pressure, disconnecting hydraulic hoses, removing mounting bolts and pins, and lifting the cylinders out of position. Reinstallation involves cleaning parts, applying grease, positioning the cylinders, and reconnecting hoses and mounting hardware. Safety precautions are provided to relieve pressure before disassembly and contain fluids properly during maintenance.
Caterpillar Cat 160M Motor Grader (Prefix B9E) Service Repair Manual (B9E0000...jfksemmdm3e
This document provides instructions for removing and installing the blade lift cylinder and sideshift cylinder on a 160M Motor Grader. It lists the required tools and safety precautions. The procedures include releasing system pressure, disconnecting hoses, removing mounting bolts, and inspecting and reinstalling components with new seals and bearings as needed. Cleanliness and applying the proper lubricants are emphasized during assembly.
Similar to Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (CML00001 and up).pdf (9)
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix MAB) Service Repair Manual (MAB00001...f8usjejkdmmd
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows the retaining nut to be safely removed with a hydraulic cylinder, releasing the compressed spring.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 247 MULTI TERRAIN LOADER CML
Configuration: 247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
247 and 257 Multi Terrain Loaders Machine Systems
Media Number -RENR4855-02 Publication Date -01/10/2009 Date Updated -29/10/2009
i01989804
Lift Cylinder - Remove and Install
SMCS - 5102-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
ZZ
6V-6509 Face Seal Plug (13/16 - 16 THD) 4
6V-9830 Cap As (13/16 - 16 THD) 4
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
1/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
2/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00891203
1. Loosen clamp (5). Disconnect tube assemblies (3) and (4). Remove bolt (2). Remove pin
assembly (1) .
Illustration 2 g00891204
The lift arm brace does not exist on the other side of the machine.
2. Remove pin (6). Lower the lift arm brace (7). Use Tooling (A) to remove retaining ring (8).
Remove pin (9). Remove the lift arm brace (7) .
3/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g00891205
3. Remove cylinder assembly (10) .
4. Repeat Steps 1 through 3 for the other side.
Disassembly and Assembly Information
Table 2
Required Tools
Tool Part Number Part Description Qty
A 127-4904 Repair Stand 1
B 195-4609 Seal Pick 1
C 5P-0960 Molybdenum Grease
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
4/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 4 g01030496
(1) Torque for the head ... 265 ± 15 N·m (195 ± 11 lb ft)
(2) Torque for the setscrew ... 22 ± 2 N·m (16 ± 1 lb ft)
(3) Torque for the nut ... 485 ± 15 N·m (358 ± 11 lb ft)
Note: Lubricate seals and sealing lips with Tooling (C) before assembly.
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
5/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 5 g00891205
1. Install cylinder assembly (10) .
6/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 6 g00891204
The lift arm brace does not exist on the other side of the machine.
2. Install the lift arm brace (7). Install pin (9). Use Tooling (A) to install retaining ring (8).
Raise the lift arm brace (7). Install pin (6) .
Illustration 7 g00891294
3. Position spacer (11) to the inside of the machine. Install pin assembly (1) .
7/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 8 g00891203
4. Install bolt (2). Connect tube assemblies (4) and (3). Tighten clamp (5) .
5. Repeat Steps 1 through 4 for the other side.
Note: The lift arm brace does not exist on the other side.
6. Check hydraulic oil level. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 10 08:59:56 UTC+0800 2019
8/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 247 MULTI TERRAIN LOADER CML
Configuration: 247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
247 and 257 Multi Terrain Loaders Machine Systems
Media Number -RENR4855-02 Publication Date -01/10/2009 Date Updated -29/10/2009
i01752020
Lift Arms - Remove and Install
SMCS - 6119-010
Removal Procedure
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B
6V-9510 Face Seal Plug (1 - 14 THD) 4
6V-9831 Cap Assembly (1 - 14 THD) 4
Note: SERVICE DATA: TOOLING (B) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
1/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g00891905
1. If equipped, remove cable strap (2) and disconnect harness assembly (1) .
2/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00891906
2. If equipped, remove bolts (4) and remove bracket (3) with the harness assembly.
Illustration 3 g00897971
The lift arm brace does not exist on the other side.
3. Remove pin (5). Lower lift arm brace (6). Use Tooling (A) to remove retaining ring (7).
Remove pin (8). Remove the lift arm brace (6) .
4. Repeat Step 3 for the other side.
3/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 4 g00908733
5. Use a suitable lifting device, lifting slings, and protective sleeves to raise the lift arms.
Illustration 5 g00897975
6. Loosen bolt (12). Disconnect tube assemblies (11) .
7. Repeat Step 6 for the other side. Lower the lift arms.
Illustration 6 g00908734
4/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 8. Attach lifting slings and protective sleeves to the middle of the lift arms. Remove bolt (10).
Remove the pin assembly (9) .
9. Repeat Step 8 for the other side.
10. Remove lift arms (13). The weight of the lift arms is approximately 314 kg (693 lb).
Installation Procedure
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
5/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 7 g00908734
1. Install lift arms (13). The weight of the lift arms is approximately 314 kg (693 lb).
2. Install pin assembly (9). Install bolt (10). Remove the lifting slings and protective sleeves
from the middle of the lift arms.
3. Repeat Step 2 for the other side. Raise the lift arms.
Illustration 8 g00897975
4. Connect tube assemblies (11). Tighten bolt (12) .
5. Repeat Step 4 for the other side.
6/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 9 g00908733
6. Lower the lift arms. Remove the suitable lifting device, lifting slings, and protective sleeves
from the lift arms.
Illustration 10 g00897971
The lift arm brace does not exist on the other side.
7. Install the lift arm brace (6). Install pin (8). Use Tooling (A) to install retaining ring (7).
Raise lift arm brace (6). Install pin (5) .
8. Repeat Step 7 for the other side.
7/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 11 g00891906
9. If equipped, install bracket (3) with the harness assembly and install bolts (4) .
Illustration 12 g00891905
10. If equipped, connect the harness assembly (1) and install cable strap (2) .
11. Check the hydraulic oil level. Refer to Operation and Maintenance Manual, SEBU7494,
"Hydraulic System Oil Level - Check".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 10 09:00:52 UTC+0800 2019
8/8
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 247 MULTI TERRAIN LOADER CML
Configuration: 247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
247 and 257 Multi Terrain Loaders Machine Systems
Media Number -RENR4855-02 Publication Date -01/10/2009 Date Updated -29/10/2009
i01755726
Pilot Operated Hydraulic Control - Remove
SMCS - 5059-011; 5705-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-9507 Face Seal Plug (9/16 - 18 THD) 12
6V-9828 Cap As (9/16 - 18 THD) 12
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Raise the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Note: SERVICE DATA: TOOLING (A) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
1/5
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g00898322
1. Remove four screws (1). Remove cover (2) .
2/5
247 257 Multi Terrain Loader CML00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...