This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjsjkseikdmme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The steps include disconnecting the fuel line, removing the sight cover and solenoid. Nuts and bolts are removed to take off the pump which is spring loaded. Gasket shims and studs if needed are installed before reinstalling the pump, lever, spring and sight cover. Cleanliness of fuel system components is emphasized.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkksemm
The document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. It describes:
1) Disconnecting the fuel line and removing the sight cover from the fuel injection pump.
2) Using a special tool to hold the governor control arm while removing the spring and nut.
3) Positioning the lever and removing additional parts from the pump.
4) Reversing the removal steps for installation, ensuring proper torque of fasteners.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader. The disassembly process involves removing 17 parts from the fuel injection pump and governor assembly including bolts, seals, shafts, springs, levers and gears. The assembly process describes installing these 17 parts in reverse order and provides torque specifications for certain bolts and nuts. Tools including an injection pump gear puller and bearing puller are required.
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader.
2) The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and fuel camshaft.
3) The assembly procedure instructs installing the parts in reverse order and provides torque specifications for tightening bolts and nuts.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjsjkseikdmme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The steps include disconnecting the fuel line, removing the sight cover and solenoid. Nuts and bolts are removed to take off the pump which is spring loaded. Gasket shims and studs if needed are installed before reinstalling the pump, lever, spring and sight cover. Cleanliness of fuel system components is emphasized.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkksemm
The document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. It describes:
1) Disconnecting the fuel line and removing the sight cover from the fuel injection pump.
2) Using a special tool to hold the governor control arm while removing the spring and nut.
3) Positioning the lever and removing additional parts from the pump.
4) Reversing the removal steps for installation, ensuring proper torque of fasteners.
Caterpillar cat 246 d skid steer loader (prefix hmr) service repair manual (h...fjjsefkkertsemme
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting bolts and nuts, and cleaning components. When installing, new gasket shims are used and bolts are tightened to the specified torques. Special care must be taken when removing the spring-loaded fuel injection pump.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
The document provides instructions for disassembling and assembling a fuel injection pump and governor for a 246D Skid Steer Loader. The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, spring, and fuel camshaft. The assembly procedure instructs installing these 17 parts in reverse order and provides torque specifications for nuts and bolts. Additionally, the document describes removing and installing the entire fuel injection pump, removing fuel lines, and cleaning parts.
This document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader. The disassembly process involves removing 17 parts from the fuel injection pump and governor assembly including bolts, seals, shafts, springs, levers and gears. The assembly process describes installing these 17 parts in reverse order and provides torque specifications for certain bolts and nuts. Tools including an injection pump gear puller and bearing puller are required.
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor for a 242D Skid Steer Loader.
2) The disassembly procedure involves removing 17 parts including the governor housing assembly, shaft, springs, and fuel camshaft.
3) The assembly procedure instructs installing the parts in reverse order and provides torque specifications for tightening bolts and nuts.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. Detailed illustrations supplement the text to show the component locations and installation/removal procedures.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using a soft hammer if needed to separate the housing from the cylinder block. The installation procedure specifies cleaning the mating surfaces and inserting a new felt seal if needed before reversing the removal steps. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts. For engines with a 14-bolt housing, the instructions are to remove the flywheel, housing bolts, seal and gasket, and housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening the bolts in sequence. Installation involves cleaning, lubricating, placing the seal and gasket in position, and tightening the bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and installing the new pulley by aligning dowel pins and tightening bolts to the specified torque. Safety notices are included to keep parts clean and contain fluids during disassembly.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. It describes removing mounting bolts and lifting the housing off dowels using linking brackets. For installation, it details cleaning mating surfaces, positioning the housing on dowels using linking brackets, and tightening mounting bolts to the specified torques. Tools required include linking brackets and a lifting device.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fusekddmm3e
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing mounting brackets and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fusekddmm3e
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing bolts, and removing the pump. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts to detach it from the exhaust manifold. Disassembly separates the housing components. Assembly reconnects the parts.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fusekddmm3e
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fusekddmm3e
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting linkages, tubes, and clips connecting the governor. Individual parts like O-rings and seals must also be removed. Installation is the reverse, applying lubricant to new seals and using tools to connect linkages and pins. Proper adjustment of the fuel setting is required after installation.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fusekddmm3e
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure instructs to drill holes in the existing seal and use a slide hammer puller to remove it. For installation, a front seal installer tool is used to push the new seal onto the crankshaft flange. Proper cleaning of parts and use of retaining compound is emphasized.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also details removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The removal procedure involves using a link bracket and forcing bolts to remove the flywheel from the housing. The installation procedure specifies cleaning and applying compounds before pressing the ring gear and wear sleeve onto the crankshaft and flywheel. Torque specifications are provided for reinstalling components like the flywheel housing bolts.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. Detailed illustrations supplement the text to show the component locations and installation/removal procedures.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using a soft hammer if needed to separate the housing from the cylinder block. The installation procedure specifies cleaning the mating surfaces and inserting a new felt seal if needed before reversing the removal steps. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts. For engines with a 14-bolt housing, the instructions are to remove the flywheel, housing bolts, seal and gasket, and housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening the bolts in sequence. Installation involves cleaning, lubricating, placing the seal and gasket in position, and tightening the bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and installing the new pulley by aligning dowel pins and tightening bolts to the specified torque. Safety notices are included to keep parts clean and contain fluids during disassembly.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. It describes removing mounting bolts and lifting the housing off dowels using linking brackets. For installation, it details cleaning mating surfaces, positioning the housing on dowels using linking brackets, and tightening mounting bolts to the specified torques. Tools required include linking brackets and a lifting device.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fusekddmm3e
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing mounting brackets and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fusekddmm3e
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing bolts, and removing the pump. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts to detach it from the exhaust manifold. Disassembly separates the housing components. Assembly reconnects the parts.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fusekddmm3e
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fusekddmm3e
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting linkages, tubes, and clips connecting the governor. Individual parts like O-rings and seals must also be removed. Installation is the reverse, applying lubricant to new seals and using tools to connect linkages and pins. Proper adjustment of the fuel setting is required after installation.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fusekddmm3e
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure instructs to drill holes in the existing seal and use a slide hammer puller to remove it. For installation, a front seal installer tool is used to push the new seal onto the crankshaft flange. Proper cleaning of parts and use of retaining compound is emphasized.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also details removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The removal procedure involves using a link bracket and forcing bolts to remove the flywheel from the housing. The installation procedure specifies cleaning and applying compounds before pressing the ring gear and wear sleeve onto the crankshaft and flywheel. Torque specifications are provided for reinstalling components like the flywheel housing bolts.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242439
Fuel Injection Pump and Governor - Disassemble
SMCS - 1286-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Start By:
a. Remove fuel injection pump and governor.
Illustration 1 g02805638
1/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Inspect fuel injection pump and governor (1).
2. Remove tube (2).
Illustration 2 g02805639
3. Use suitable blocking and position the fuel injection pump and governor. Remove bolts (4)
and remove governor housing assembly (3).
4. Remove two bolts (4B) and remove stop solenoid (4A). Replace o-ring if necessary.
Illustration 3 g02805640
5. Remove and inspect O-ring seal (5) from governor housing assembly (3). If necessary,
replace O-ring seal (5) with new.
6. Remove shaft (6) and spring (7) from governor housing assembly (3). Remove governor
lever (8).
2/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g02805641
7. Remove pin (10) from governor lever assembly (12).
8. Remove speed control lever (9) and spring (11) from governor lever assembly (12).
9. Remove spring (13) and remove governor lever assembly (12) with the O-ring seals.
Illustration 5 g02805656
Illustration 6 g02805658
10. Remove governor sleeve (13) and nut (16). Remove governor weights (15).
3/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g02805660
Illustration 8 g02805696
11. Remove nut (17) from gear (18).
Note: Nut (17) has reverse threads.
12. Use Tooling (A) to remove gear (18).
Illustration 9 g02805716
13. Remove bolts (19) and retaining plate (20).
14. Remove fuel camshaft (24) from the housing assembly.
4/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 15. Remove screws (21) and retaining plate (22). If necessary, replace key (23) with new.
Illustration 10 g02805762
Illustration 11 g02805764
Illustration 12 g02805765
16. Use a suitable press and Tooling (B) to remove bearing (25) from fuel camshaft (24) and
ring (27).
17. Use a suitable press and Tooling (B) to remove bearing (26) from fuel camshaft (24).
5/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242445
Fuel Injection Pump and Governor - Assemble
SMCS - 1286-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1150 Injection Pump Gear Puller 1
154-6360 Bolt 1
B 8H-0663 Bearing Puller 1
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g02805765
1/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g02807019
Illustration 3 g02807020
1. Use Tooling (B) and a suitable press to install bearings (26) onto fuel camshaft (24).
2. Position ring (27). Use Tooling (B) and a suitable press to install bearings (25) onto fuel
camshaft (24).
Illustration 4 g02805716
3. If necessary, replace key (23) with new. Position retaining plate (22) and install screws (21).
Tighten screws (21) to a torque of 3.9 to 4.2 N·m (34.5 to 37.4 lb in).
2/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Position fuel camshaft (24) in the housing assembly.
5. Position retaining plate (20) and install bolts (19). Tighten bolts (19) to a torque of
10 to 11 N·m (87 to 100 lb in).
Illustration 5 g02805660
6. Install gear (18).
7. Install nut (17) to gear (18).
8. For the C3.3B Tighten nut (17) to a torque of 138 to 156 N·m (102 to 115 lb ft).
9. For the C2.6 Tighten nut (17) to a torque of 93 to 102 N·m (69 to 75 lb ft).
Illustration 6 g02805658
3/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g02805656
10. Position governor weights (15) and install nut (16). Tighten nut (16) to a torque of
63 to 72 N·m (47 to 53 lb ft). Install governor sleeve (14).
Illustration 8 g02805641
Note: Apply engine oil to all internal parts of governor.
11. Install O-ring seals on governor lever assembly (13). Position governor lever assembly (13)
into the governor housing and install spring (12).
12. Install spring (11) and speed control lever (9) on governor lever assembly (13).
13. Install pin (10) into governor lever assembly (13).
4/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 9 g02805640
14. Position governor lever (8). Install shaft (6) and spring (7) in governor housing assembly
(3).
15. If necessary, replace O-ring seal (5) with new. Install O-ring seal (5) in governor housing
assembly (3).
Illustration 10 g02805639
16. Use a suitable blocking to support the fuel injection pump and governor. Position governor
housing assembly (3) and install bolts (4). Tighten bolts (4) to a torque of 10 to 11 N·m
(87 to 100 lb in).
Illustration 11 g02805638
17. Inspect fuel injection pump and governor (1) for installation.
18. Install tube (2).
End By:
a. Install fuel injection pump and governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Mon Nov 11 23:39:45 UTC+0800 2019
5/6
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g03177762
1. If necessary, install studs (10) and remove cover (11).
Illustration 2 g03177759
2. Install the O-ring seal on fuel injection pump and governor (9). Position fuel injection pump
and governor (9) onto the flywheel housing.
3. Install three nuts (8) to fuel injection pump and governor (9). Tighten nuts (8) to a torque of
18 to 20 N·m (159 ± 177 lb in).
Illustration 3 g03177783
3/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Apply engine oil to threads and torque fitting (7) to a torque of 16 to 19 N·m (12 to 14 lb ft).
5. Install engine oil pressure sensor (6) and connect the wiring harness assembly. Tighten the
engine oil pressure sensor (6) to a torque of 15 to 19 N·m (11 to 14 lb ft).
Illustration 4 g02804519
6. Position bracket (3) and install two nuts (4) and two bolts (5).
Illustration 5 g02804516
7. Check the timing marks and install the O-ring seal and oil plug cap (1). Install the O-ring
seal and cover (2) on flywheel housing (3).
End By:
a. Install the fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:40:41 UTC+0800 2019
4/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242455
Fuel Injection Pump - Remove and Install
SMCS - 1251-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1150 Injection Pump Gear Puller 1
Start By:
a. Remove fuel injection line.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
1/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02781037
3. Disconnect hose assembly (2) from fuel injection pump (1).
4. Remove sight cover (3) from fuel injection pump (1).
Illustration 2 g02874459
5. Remove the shutoff solenoid and cover (1A). Install Tooling (A) to hold back the governor
control arm and assist removing the spring (5) and nut (4).
Illustration 3 g02781105
6. Disconnect spring (5) and attach a thin wire to spring (5). Remove nut (4). Position the lever
off the stud.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Remove two nuts (6) and four bolts (7) from fuel injection pump (1). The fuel injection
pump (1) is spring loaded.
8. Carefully remove fuel injection pump (1) from the fuel injection pump housing.
Illustration 4 g02781040
9. Remove gasket shims (8).
10. If necessary, remove studs (9) from the fuel injection pump housing.
11. To secure the spring from falling inside the housing use wire (10).
12. Clean fuel injection pump (1) and the area around the fuel injection pump. Ensure that the
area is free from contamination before beginning installation.
Installation Procedure
NOTICE
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
3/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g02781040
1. Keep wire (10) secure to the spring to prevent falling into the housing.
2. If necessary, install studs (9) into the fuel injection pump housing.
3. Position new gasket shims (8) onto the fuel injection pump housing.
Note: When you disassemble or replace, make sure that you use the same number of new
gasket shims with the same thickness.
Illustration 6 g02781105
4. Carefully install fuel injection pump (1) into the fuel injection pump housing .
5. Install four new bolts (7) into fuel injection pump (1). Install two nuts (6) into fuel injection
pump (1). Tighten bolts (7) to a torque of 24 to 27 N·m (214 to 240 lb in). Tighten nuts (6)
to a torque of 18 to 20 N·m (159 to 178 lb in).
4/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g02781722
6. Position the lever on the stud. Install nut (4) to hold the lever in place. Tighten nut (4) to a
torque of 3 to 4 N·m (26 to 36 lb in).
7. Connect spring (5) with the thin wire.
Illustration 8 g02781037
8. Install sight cover (3).
9. Connect hose assembly (2) to fuel injection pump (1).
10. Turn the fuel supply to the ON position.
11. Turn the battery disconnect switch to the ON position.
12. After replacement of the fuel injection pump, the fuel injection pump must be calibrated.
Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check".
End By:
a. Install fuel injection lines.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:41:37 UTC+0800 2019
5/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02782212
1. Disconnect hose assembly (2) from turbocharger (1).
2. Remove tube assembly (3) from turbocharger (1).
3. Remove bolt (4) and the four lower bolts. Remove tube assemblies (5) and the gasket and
the O-ring seal.
Illustration 2 g02782214
4. Remove five bolts (7) and housing (8) and the gasket.
5. Remove four nuts (6) and turbocharger (1) and the gasket.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite C5A 1
3/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g02782214
1. If necessary, install new gaskets.
2. Position the gasket and install turbocharger (1) on the exhaust manifold.
3. Position the gasket and install housing (8) on the turbocharger (1) and install three bolts (7)
to align turbocharger (1).
4. Apply Tooling (A) to three nuts (6) and install three nuts (6) on turbocharger (1). Tighten
three nuts (6) and remove three bolts (7) and housing (8).
5. Apply Tooling (A) to one nut (6) and install one nut (6) on turbocharger (1). Tighten one
nut (6).
6. Position the gasket and housing (8). Apply Tooling (A) on bolts (7) and install five bolts (7)
and tighten.
Illustration 4 g02782212
7. Position tube assemblies (5) and the gasket and the O-ring seal and install four lower bolts
and bolt (4). Tighten bolt (4) to a torque of 16.0 ± 19.0 N·m (11.80 ± 14.01 lb ft).
8. Position tube assembly (3) on turbocharger (1) and install the clamps.
9. Connect hose assembly (2) on turbocharger (1).
Mon Nov 11 23:42:32 UTC+0800 2019
4/5
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242491
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
7F-4292 Valve Spring Compressor 1
9U-6144 Adapter 1
Start By:
a. Remove the rocker shaft and push rod.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head
that has been removed from the engine.
Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
1/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02799356
Illustration 2 g02725099
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 1. Follow Step 1.a through Step 1.d in order to position the appropriate piston at top dead
center.
a. Install Tooling (A) in position on the cylinder head in order to compress a valve
spring (4) for the appropriate piston.
b. Use Tooling (A) in order to compress valve spring (4) and open the valve slightly.
Note: Do not compress the spring so that valve spring retainer (3) touches the valve
stem seal.
c. Rotate the crankshaft carefully, until the piston touches the valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in
bent valve stems.
d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A)
until the piston is at the top dead center position. The valve is now held in a position
that allows the valve spring to be safely removed.
Note: If all valve springs require replacement, the procedure can be carried out on two
cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
2. Remove valve cap (1). Apply sufficient pressure to Tooling (A) in order to allow removal of
valve keepers (2).
Note: Do not compress the spring so that valve spring retainer (3) touches the valve stem
seal.
3. Slowly release pressure on Tooling (A).
4. Remove valve spring retainer (3) and remove valve spring (4).
3/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g02725101
5. Remove Tooling (A).
6. Remove valve stem seals (5).
7. Repeat Step 2 through Step 5 in order to remove the remaining valve springs from the
appropriate cylinder.
Installation Procedure
1. Install the inlet and exhaust valve springs (4) in the reverse order of removal.
Illustration 4 g02862476
a. Install valve springs with the smaller pitch end (6) downward on cylinder head side.
b. Inspect valve springs (4) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves " for further information.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 11 23:45:20 UTC+0800 2019
4/4
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246D SKID STEER LOADER HMR
Configuration: 246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242493
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove cylinder head.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below
the face of the cylinder head before the valve springs are removed. Refer to Specifications,
"Cylinder Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 23 kg (51 lb).
1/3
246D Skid Steer Loader HMR00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...