The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The removal procedure involves using a link bracket and forcing bolts to remove the flywheel from the housing. The installation procedure specifies cleaning and applying compounds before pressing the ring gear and wear sleeve onto the crankshaft and flywheel. Torque specifications are provided for reinstalling components like the flywheel housing bolts.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. Detailed illustrations supplement the text to show the component locations and installation/removal procedures.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using a soft hammer if needed to separate the housing from the cylinder block. The installation procedure specifies cleaning the mating surfaces and inserting a new felt seal if needed before reversing the removal steps. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts. For engines with a 14-bolt housing, the instructions are to remove the flywheel, housing bolts, seal and gasket, and housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening the bolts in sequence. Installation involves cleaning, lubricating, placing the seal and gasket in position, and tightening the bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and installing the new pulley by aligning dowel pins and tightening bolts to the specified torque. Safety notices are included to keep parts clean and contain fluids during disassembly.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. It describes removing mounting bolts and lifting the housing off dowels using linking brackets. For installation, it details cleaning mating surfaces, positioning the housing on dowels using linking brackets, and tightening mounting bolts to the specified torques. Tools required include linking brackets and a lifting device.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fusekddmm3e
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing mounting brackets and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fusekddmm3e
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing bolts, and removing the pump. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts to detach it from the exhaust manifold. Disassembly separates the housing components. Assembly reconnects the parts.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fusekddmm3e
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fusekddmm3e
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting linkages, tubes, and clips connecting the governor. Individual parts like O-rings and seals must also be removed. Installation is the reverse, applying lubricant to new seals and using tools to connect linkages and pins. Proper adjustment of the fuel setting is required after installation.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fusekddmm3e
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure instructs to drill holes in the existing seal and use a slide hammer puller to remove it. For installation, a front seal installer tool is used to push the new seal onto the crankshaft flange. Proper cleaning of parts and use of retaining compound is emphasized.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also details removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the flywheel. Precautions are provided to keep parts clean and contain fluids.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and using lifting tools to detach the housing from the cylinder block. The installation procedure specifies cleaning parts, placing the housing in position, and tightening mounting bolts to secure the housing. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. Detailed illustrations supplement the text to show the component locations and installation/removal procedures.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using a soft hammer if needed to separate the housing from the cylinder block. The installation procedure specifies cleaning the mating surfaces and inserting a new felt seal if needed before reversing the removal steps. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing using lifting tools. The installation procedure specifies cleaning mating surfaces, placing the housing on dowels in the cylinder block, and tightening mounting bolts to specified torques. Tools, safety precautions, and references to other repair procedures are also listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts. For engines with a 14-bolt housing, the instructions are to remove the flywheel, housing bolts, seal and gasket, and housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening the bolts in sequence. Installation involves cleaning, lubricating, placing the seal and gasket in position, and tightening the bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and installing the new pulley by aligning dowel pins and tightening bolts to the specified torque. Safety notices are included to keep parts clean and contain fluids during disassembly.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. It describes removing mounting bolts and lifting the housing off dowels using linking brackets. For installation, it details cleaning mating surfaces, positioning the housing on dowels using linking brackets, and tightening mounting bolts to the specified torques. Tools required include linking brackets and a lifting device.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fusekddmm3e
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing mounting brackets and disconnecting various components to remove the cylinder head.
3. Installing a new gasket and torquing bolts to the specified values to install the cylinder head. Reconnecting components and filling the cooling system.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fusekddmm3e
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing bolts, and removing the pump. Installation is the reverse.
3. Turbocharger removal requires removing bolts and nuts to detach it from the exhaust manifold. Disassembly separates the housing components. Assembly reconnects the parts.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fusekddmm3e
This document provides instructions for removing and installing inlet and exhaust valve seats in a 322C FM excavator engine. It outlines the required tools and gives step-by-step procedures for removal and installation. Removal involves using a valve seat extractor tool to pull each seat from the cylinder head. Installation requires tapping new seats into place and ensuring they are flush with the head. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fusekddmm3e
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting linkages, tubes, and clips connecting the governor. Individual parts like O-rings and seals must also be removed. Installation is the reverse, applying lubricant to new seals and using tools to connect linkages and pins. Proper adjustment of the fuel setting is required after installation.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The flywheel removal procedure involves using a link bracket and forcing bolts to lift the 50 kg flywheel out of the housing. Reinstallation follows the reverse process, and technicians are advised to clean parts and check for proper installation.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fusekddmm3e
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure instructs to drill holes in the existing seal and use a slide hammer puller to remove it. For installation, a front seal installer tool is used to push the new seal onto the crankshaft flange. Proper cleaning of parts and use of retaining compound is emphasized.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fusekddmm3e
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also details removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D excavator engine. It describes using various tools to remove components like the muffler, flywheel, flywheel bolts, and flywheel housing bolts. Detailed illustrations show each step, like installing a lifting bracket and bolts to remove the flywheel. Precautions are provided to keep parts clean and contain fluids.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:18:23 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:19:19 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:21:11 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:22:06 UTC+0800 2020
4/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...