This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes the removal and installation procedures for both Type 1/9RM and Type 2/7BJ engines. The procedures involve removing bolts and nuts, inspecting and replacing gaskets if needed, and reinstalling components in the reverse order of removal while keeping parts clean from contaminants. Diagrams illustrate the components and numbered steps in the procedures.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01598347
Exhaust Manifold - Remove and Install - Type 2 Engines and
7BJ Engines
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
B. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove and Install".
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00557287
Typical example
Illustration 2 g00557337
1. Remove exhaust manifold nuts or bolts (1) in reverse order of the numbered sequence.
2. Remove exhaust manifold (2) from the engine.
2/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00557351
Typical example
3. Remove exhaust manifold gaskets (3) from the engine.
4. Remove old sealant from stud threads.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00557351
Typical example
3/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Inspect the condition of the gaskets. If the gaskets are damaged, use new parts for
replacement. Install exhaust manifold gaskets (3) on the cylinder head. Apply 4C-9507
Retaining Compound to the stud threads.
Illustration 5 g00557287
Typical example
Illustration 6 g00557337
NOTICE
Damage to the exhaust manifold can occur if the exhaust manifold is
not aligned and tightened correctly.
4/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 2. Install exhaust manifold (2) on the cylinder head.
Note: Some of the exhaust manifolds have large clearance holes for the bolts. If a new
exhaust manifold is installed ensure that the 148-7132 Ferrule mountings that are supplied
with the exhaust manifold are installed.
3. Install exhaust manifold nuts or bolts (1). Tighten the exhaust manifold nuts or bolts in the
numerical sequence to a torque of 44 N·m (33 lb ft).
End By:
a. Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove and Install".
b. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:42:57 UTC+0800 2019
5/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01068659
Exhaust Manifold - Remove and Install - Type 1 Engines and
9RM Engines
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00542541
Typical example
1. Remove exhaust manifold nuts (1) .
2. Remove exhaust manifold (2) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00542541
Typical example
2/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket and exhaust manifold (2) .
3. Install exhaust manifold nuts (1). Tighten the plated nuts to a torque of 44 N·m (32 lb ft).
Tighten the nuts that are not plated to a torque of 50 N·m (37 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:43:52 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870246
Inlet Manifold - Remove - Type 2 Engines and 7BJ Engines
SMCS - 1058-011
Removal Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00557838
Typical example
1. Disconnect tube (1) from the air inlet heater.
2. Loosen hose clamps (3) and slide the hose toward the turbocharger.
3. Remove four bolts (2) and remove elbow (4) from the air inlet manifold.
Illustration 2 g00558245
Typical example
4. Remove bolts (5) that fasten air inlet manifold (6) to the engine.
5. Remove air inlet manifold (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:44:48 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870245
Inlet Manifold - Remove - Type 1 Engines and 9RM Engines
SMCS - 1058-011
Removal Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00545513
Typical example
Illustration 2 g00545514
Typical example
1. Disconnect electrical connector (5) for the air inlet heater.
2. Disconnect fuel line (6) to the air inlet heater.
3. Remove two bolts (7) that hold the bracket for fuel line (6) in position.
4. Loosen two hose clamps (8) and slide hose (9) toward the turbocharger.
5. Remove four bolts (3) in order to remove elbow (2) and gasket (4) .
6. Disconnect boost pressure hose (10) .
7. Remove bolts (12) that hold the turbocharger support to air inlet manifold (14) .
8. Remove bolts (13) that hold air inlet manifold (14) to the cylinder head.
2/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 9. Remove air inlet manifold (14) and gaskets (11) .
10. Remove seal (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:45:44 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870254
Inlet Manifold - Install - Type 1 Engines and 9RM Engines
SMCS - 1058-012
Installation Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the gaskets for wear or damage. If the gaskets are worn or damaged, use new parts
for replacement.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 1 g00545514
Typical example
Illustration 2 g00545513
Typical example
2. Install seal (1) on the engine.
3. Position gaskets (11) and air inlet manifold (14) on the engine.
Note: Ensure that the front gaskets and the rear gaskets are installed with the notch at the
top left side. The center gasket can be installed in either direction.
4. Install bolts (13) .
5. Position the turbocharger support on air inlet manifold (14) and install bolts (12) .
6. Connect boost pressure hose (10) .
7. Install gasket (4) and elbow (2) with four bolts (3) .
8. Slide hose (9) in position and tighten hose clamps (8) .
9. Place the bracket for fuel line (6) in position and install two bolts (7) .
10. Connect fuel line (6) to the air inlet heater.
11. Connect electrical connector (5) for the air inlet heater.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:46:40 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870255
Inlet Manifold - Install - Type 2 Engines and 7BJ Engines
SMCS - 1058-012
Installation Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the gaskets for wear or damage. If the gaskets are worn or damaged, use new parts
for replacement.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00558245
Typical example
2. Install the gasket and air inlet manifold (6) with bolts (5) . Tighten bolts (5) to a torque of 33
N·m (24 lb ft).
Illustration 2 g00557838
Typical example
3. Put the gasket and elbow (4) in position on the air inlet manifold.
4. Install four bolts (2) .
5. Slide the hose into position and tighten hose clamps (3) .
6. Connect tube (1) to the air inlet heater.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:47:35 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...