This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes over 30 steps to disassemble the motors by removing components like the shuttle valve, pump head, body, barrel, pistons, and more. It then describes over 20 steps for reassembling the motors, providing details on cleaning parts, applying oil, pressing components, setting bearings, and checking clearance. The goal is to properly disassemble and reassemble the swing and track motors while identifying parts to ensure correct alignment during reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate, bearings and seals. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, inserting the joint assembly and drive plate pins, and applying specified forces during assembly. Precise part identification and placement is required to correctly reassemble the motors.
Caterpillar cat 315 f l excavator (prefix tdy) service repair manual (tdy0000...fjskekdmjekm
This document provides disassembly instructions for the final drive and travel motor of a 315F LCR excavator. It outlines 14 steps to disassemble the final drive which includes removing covers, gears, bearings, and other components. It also details 23 steps to disassemble the travel motor, counterbalance valve, and other internal parts. Safety precautions are provided throughout to warn of potential hazards like released spring forces during disassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and provides a step-by-step process to disassemble each component. Safety notices are included to warn technicians of potential hazards like parts propelled by springs or remaining hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for maintenance or repair.
Caterpillar cat 312 d l excavator (prefix tgy) service repair manual (tgy0000...pfiskdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D L excavator. It lists the required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, plates, seals, springs, and other parts. Safety notices are included to warn technicians about potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor on a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 13 steps like installing seals, the shaft assembly, cam plate, and reassembling the barrel assembly components in their original positions and orientations. Precise alignment marks and tooling are required to properly reinstall parts in the travel motor.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate, bearings and seals. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, inserting the joint assembly and drive plate pins, and applying specified forces during assembly. Precise part identification and placement is required to correctly reassemble the motors.
Caterpillar cat 315 f l excavator (prefix tdy) service repair manual (tdy0000...fjskekdmjekm
This document provides disassembly instructions for the final drive and travel motor of a 315F LCR excavator. It outlines 14 steps to disassemble the final drive which includes removing covers, gears, bearings, and other components. It also details 23 steps to disassemble the travel motor, counterbalance valve, and other internal parts. Safety precautions are provided throughout to warn of potential hazards like released spring forces during disassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and provides a step-by-step process to disassemble each component. Safety notices are included to warn technicians of potential hazards like parts propelled by springs or remaining hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for maintenance or repair.
Caterpillar cat 312 d l excavator (prefix tgy) service repair manual (tgy0000...pfiskdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D L excavator. It lists the required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, plates, seals, springs, and other parts. Safety notices are included to warn technicians about potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor on a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 13 steps like installing seals, the shaft assembly, cam plate, and reassembling the barrel assembly components in their original positions and orientations. Precise alignment marks and tooling are required to properly reinstall parts in the travel motor.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake, then disassembling the swing drive into individual components. These include removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including any special tools needed and component weights. The purpose is to repair or replace parts within the swing drive assembly.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
The document provides instructions for disassembling and removing various components of an axle housing, including the brake cylinder assembly, differential and bevel gear assembly, planetary gears, pinion shaft, and solenoid valve. Specific tools are listed and steps include removing bolts, plates, seals, springs, and other parts using tools like spanner wrenches, pullers, and hammers. Detailed illustrations accompany each step.
This document provides disassembly instructions for the final drive, travel motor, and other components of excavator models 312D2 and 312D2 L. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using various tools. It then details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and other parts. Safety notices are included throughout to warn of potential injuries from springs, fluids and heavy components.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and fasteners, using pullers to remove bearings, and noting part locations and orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy lifting, and released spring forces.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to ensure correct reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to facilitate correct reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to ensure correct reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor, swing drive, and brake before disassembling the swing drive components. These include removing bearing cages, seals, gears, and shafts. Precautions are described for releasing hydraulic pressure and preventing parts from falling during disassembly. The assembly instructions reverse the disassembly steps and provide torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key steps include releasing oil pressure, removing the swing drive motor and brake, and taking apart the case assembly housing to access internal gears, seals, bearings and other components. Proper cleaning and application of anti-seize compound is emphasized during reassembly to ensure correct functioning of the swing drive.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake, then disassembling the swing drive into individual components. These include removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including any special tools needed and component weights. The purpose is to repair or replace parts within the swing drive assembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake before disassembling the swing drive itself. Key steps include removing bearing cages, seals, gears, and the pinion shaft. Precautions are outlined such as using eyebolts and hoists to safely remove heavy components. The assembly process reverses these steps and includes applying anti-seize compound and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various oil lines and tubes, bearings, gears, and other internal components. Proper cleaning and application of anti-seize compound is emphasized during reassembly to ensure correct functioning of the swing drive.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various oil lines and tubes, bearings, gears, and casing components. Proper cleaning and application of anti-seize compound to specific areas is emphasized. Torque specifications and special tools are referenced throughout the process.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including necessary tools. The purpose is to repair or replace components while maintaining proper assembly procedures.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
This document provides instructions for disassembling and assembling various components of a 215 Excavator powered by a 3402 engine, including the fuel pump drive, governor, and fuel injection pumps. It describes removing and installing parts like the fuel block, fuel pump drive, governor housing, torque control, weight assembly, and fuel injection pumps. Detailed steps are provided for disassembling and assembling the fuel pump drive, governor, and ensuring proper measurements and alignments during assembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake, then disassembling the swing drive into individual components. These include removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including any special tools needed and component weights. The purpose is to repair or replace parts within the swing drive assembly.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
The document provides instructions for disassembling and removing various components of an axle housing, including the brake cylinder assembly, differential and bevel gear assembly, planetary gears, pinion shaft, and solenoid valve. Specific tools are listed and steps include removing bolts, plates, seals, springs, and other parts using tools like spanner wrenches, pullers, and hammers. Detailed illustrations accompany each step.
This document provides disassembly instructions for the final drive, travel motor, and other components of excavator models 312D2 and 312D2 L. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using various tools. It then details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and other parts. Safety notices are included throughout to warn of potential injuries from springs, fluids and heavy components.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and fasteners, using pullers to remove bearings, and noting part locations and orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy lifting, and released spring forces.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to ensure correct reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to facilitate correct reassembly.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes in detail removing over 30 individual parts including the swing motor, track motors, pump head, body, barrel, pistons, drive plate and various seals and bearings. Reassembly requires cleaning all parts, applying oil, pressing in bearing cups, heating and installing bearing cones, and reinstalling over 30 parts in reverse order. Precise identification of matching parts and careful handling is emphasized to ensure correct reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor, swing drive, and brake before disassembling the swing drive components. These include removing bearing cages, seals, gears, and shafts. Precautions are described for releasing hydraulic pressure and preventing parts from falling during disassembly. The assembly instructions reverse the disassembly steps and provide torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key steps include releasing oil pressure, removing the swing drive motor and brake, and taking apart the case assembly housing to access internal gears, seals, bearings and other components. Proper cleaning and application of anti-seize compound is emphasized during reassembly to ensure correct functioning of the swing drive.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake, then disassembling the swing drive into individual components. These include removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including any special tools needed and component weights. The purpose is to repair or replace parts within the swing drive assembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive motor and brake before disassembling the swing drive itself. Key steps include removing bearing cages, seals, gears, and the pinion shaft. Precautions are outlined such as using eyebolts and hoists to safely remove heavy components. The assembly process reverses these steps and includes applying anti-seize compound and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various oil lines and tubes, bearings, gears, and other internal components. Proper cleaning and application of anti-seize compound is emphasized during reassembly to ensure correct functioning of the swing drive.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various oil lines and tubes, bearings, gears, and casing components. Proper cleaning and application of anti-seize compound to specific areas is emphasized. Torque specifications and special tools are referenced throughout the process.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part, including necessary tools. The purpose is to repair or replace components while maintaining proper assembly procedures.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing the swing drive from the excavator frame, then disassembling the individual components of the swing drive including removing bearings, seals, gears, and the pinion shaft. Detailed steps are provided for each part along with notes about specific components. The overall process is broken into sections for removing the assembled swing drive, then disassembling the internal components.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
This document provides instructions for disassembling and assembling various components of a 215 Excavator powered by a 3402 engine, including the fuel pump drive, governor, and fuel injection pumps. It describes removing and installing parts like the fuel block, fuel pump drive, governor housing, torque control, weight assembly, and fuel injection pumps. Detailed steps are provided for disassembling and assembling the fuel pump drive, governor, and ensuring proper measurements and alignments during assembly.
This document provides instructions for disassembling and assembling various components of a 215 Excavator powered by a 3402 engine, including the fuel pump drive, governor, and fuel injection pumps. It describes removing and installing parts like the fuel block, fuel pump drive, governor housing, torque control, weight assembly, and fuel injection pumps. Detailed steps are provided for disassembling and assembling the fuel pump drive, governor, and ensuring proper measurements and alignments during assembly.
This document provides disassembly instructions for the transmission of a 970F wheel loader model. It outlines 52 steps to fully disassemble the transmission. These include removing various housings, pistons, gears, seals, and other components. Special tools are required for some removal steps. Weights are provided for major transmission components to aid in disassembly and handling.
This document provides disassembly and assembly instructions for the transmission of a 970F wheel loader. It describes removing over 60 individual components of the transmission in detailed steps. The highest level components disassembled include the transmission case, clutch housings, carrier assemblies, planetary gears, shafts, seals, and friction discs. Reassembly follows the reverse order of disassembly.
This document provides disassembly and assembly instructions for the transmission of a 970F wheel loader. It describes removing and disassembling the various transmission components in 62 numbered steps. These include separating the transmission from other components, removing clutch housings, planetary gear carriers, ring gears, shafts, pistons and other internal parts. Detailed instructions are given for disassembling each component.
Similar to Caterpillar cat 245 excavator (prefix 82 x) service repair manual (82x00001 and up) (20)
This document is a parts catalog for a 60Z7 wheel loader powered by a DEUTZ TCD3.6L4 engine. It lists the serial number range for the equipment as 60D1-8001 to 60D1-8001. The catalog then provides an index of parts listed by name and corresponding page numbers.
This document is the parts catalog for a Kubota 30ZV-2 wheel loader. It lists various parts for the loader's engine, electrical system, fuel system, radiator, muffler system, power train, and other components. The parts are organized into numbered sections with descriptions. The document also includes information about the loader's engine, chassis number, serial number, and parts name index.
This document is a parts catalog for a 30ZV-2 wheel loader powered by a Kubota D1803-M-D1-E3B-WLTC1 engine. It lists parts for equipment components, pumps, motors, controls, cylinders, differentials, final drives, propeller shafts, and other parts. The parts are organized by assembly, item number, part number, name, quantity, and serial number range. Notes provide information on applicable models and replacing parts.
This document is a parts catalog for equipment model 30ZV-2 that lists over 90 individual parts. It includes the serial number range for the model and outlines the chassis number and manufacturer's serial number labeling convention. The second page provides a parts name index to allow cross-referencing of part names and page numbers.
Isuzu 4 hk1 diesel engine service repair manualfujsekfksmemer
This document provides instructions for disassembling and removing components from an Isuzu 4HK1 diesel engine used in Kawasaki wheel loaders. The summary includes:
1) The document outlines procedures for removing components like the cylinder head assembly, turbocharger assembly, fuel injection system, valves and guides from the engine.
2) Key steps include draining coolant, removing exhaust and intake components, disconnecting fuel lines and electrical connections.
3) Precautions are provided to avoid damaging parts and properly organize removed components to prevent mixing up parts between cylinders.
Hyster u005 (h120 ft) forklift service repair manualfujsekfksmemer
This document provides specifications for various lift truck models including:
1) Lifting capacities and weights for the H80FT-H120FT and S80FT-S120FT models ranging from 3,629 to 5,443 kg.
2) Tire sizes, engine specifications, fuel capacities, fluid capacities, and electrical specifications for the different models.
3) Transmission oil pressures and hydraulic system relief pressures at various temperatures and engine speeds.
4) Steering system specifications including cylinder stroke, turning angle, radius and number of turns to lock for each model.
Hyster u005 (h110 ft) forklift service repair manualfujsekfksmemer
This document provides specifications for various lift truck models including:
1) Lifting capacities and weights for the H80FT-H120FT and S80FT-S120FT models ranging from 3,629 to 5,443 kg.
2) Tire sizes, engine specifications, fuel capacities, fluid capacities, and electrical systems specs for the different models.
3) Transmission oil pressures and hydraulic system relief pressures at various temperatures and engine speeds.
4) Steering system specifications like cylinder stroke, turning radius, and turns to lock for each model.
Hyster u005 (h100 ft) forklift service repair manualfujsekfksmemer
This document provides specifications for various lift truck models including:
1) Lifting capacities and weights for the H80FT-H120FT and S80FT-S120FT models ranging from 3,629 to 5,443 kg.
2) Tire sizes, engine specifications, fuel capacities, fluid capacities, and electrical specifications for the different models.
3) Transmission oil pressures and hydraulic system relief pressures at various temperatures and engine speeds.
4) Steering system specifications including cylinder stroke, turning angle, radius and number of turns to lock for each model.
Hyster u005 (h90 ft) forklift service repair manualfujsekfksmemer
This document provides specifications for various lift truck models including:
1) Lifting capacities and weights for the H80FT-H120FT and S80FT-S120FT models ranging from 3,629 to 5,443 kg.
2) Tire sizes, engine specifications, fuel capacities, fluid capacities, and electrical systems specs for the different models.
3) Transmission oil pressures and hydraulic system relief pressures at various temperatures and engine speeds.
4) Steering system specifications like cylinder stroke, turning radius, and turns to lock for each model.
Hyster u005 (h80 ft) forklift service repair manualfujsekfksmemer
This document provides specifications for various lift truck models including:
1) Lifting capacities and weights for the H80FT-H120FT and S80FT-S120FT models ranging from 3,629 to 5,443 kg.
2) Tire sizes, engine specifications, fuel capacities, fluid capacities, and electrical specifications for the different models.
3) Transmission oil pressures and hydraulic system relief pressures at various temperatures and engine speeds.
4) Steering system specifications including cylinder stroke, turning angle, radius and number of turns to lock for each model.
Hyster u005 (h5.5 ft europe) forklift service repair manualfujsekfksmemer
This document provides specifications and service information for Hyster lift truck models including:
- Lift capacities and weights for various models
- Tire sizes for drive and steer tires
- Fuel, oil, and fluid capacities
- Instructions for removing the drive axle which include draining fluids, disconnecting lines, and lowering the axle assembly.
Hyster u005 (h5.0 ft europe) forklift service repair manualfujsekfksmemer
This document provides specifications and service information for Hyster lift truck models including:
- Lift capacities and weights for various models
- Tire sizes for drive and steer tires
- Fuel, oil, and fluid capacities
- Instructions for removing the drive axle which include draining fluids, disconnecting lines, and lowering the axle assembly.
Hyster u005 (h4.5 fts5 europe) forklift service repair manualfujsekfksmemer
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes for drive and steer tires
- Fuel, oil, coolant, and hydraulic tank capacities
- Procedures for removing the drive axle, which involves draining fluids, disconnecting brake and drive lines, and removing mounting bolts.
Hyster u005 (h4.0 ft6 europe) forklift service repair manualfujsekfksmemer
This document provides specifications and service information for Hyster lift truck models including:
- Lift capacities and weights for various models
- Tire sizes for drive and steer tires
- Fuel, oil, and fluid capacities
- Instructions for removing the drive axle which include draining fluids, disconnecting lines, and lowering the axle assembly.
Hyster u005 (h4.0 ft5 europe) forklift service repair manualfujsekfksmemer
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes for drive and steer tires
- Fuel, oil, coolant, and hydraulic tank capacities
- Procedures for removing the drive axle, which involves draining fluids, disconnecting brake and drive lines, and removing mounting bolts.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 82X
Configuration: 245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
245 EXCAVATOR VEHICLE SYSTEMS
Media Number -SENR7339-02 Publication Date -01/01/1983 Date Updated -12/10/2001
Swing And Track Motors
SMCS - 5058-16; 5058-15
Disassemble Swing And Track Motors
start by:
a) remove swing motor
b) remove track motors
1/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Fasten adapter and bracket (1), part of tooling (A), to the track motor as shown with three 3/4"-10
NC bolts 21/4 inches long. Fasten a hoist and put the track motor in position on the engine stand of
tooling (A). Weight of the track motor is 210 lb. (95 kg).
2. Loosen plugs (2) in the shuttle valve. Remove bolts (3) and shuttle valve (4) from the pump head.
NOTE: On earlier machines the shuttle valve location is on the upper body.
3. Remove plugs (2), O-ring seals (5), balls (6) and pin (7) from the shuttle valve. Remove O-ring
seals (8) and (9) from the shuttle valve.
NOTE: On earlier machines there are stops behind plugs (2) with a ring and seal on each stop Use
an 8-32 screw to pull the stops from the shuttle valve.
4. Bend the lock back and remove bolt (10), the lock and retainer from the shaft.
2/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Put identification on the pump head as to its location on the body for correct alignment at
assembly. Remove bolts (11) and pump head (12) from the body.
6. Remove O-ring seal (13) from body (14).
7. Put identification on body (14) as to its location on the lower body.
NOTICE
Do not let the pump barrel fall when body (14) is removed. Install
protective plate (B) on the pump barrel. Keep protective plate (B) on
the pump barrel at all times to prevent damage to the face of the pump
barrel.
8. Remove bolts (15) and body (14) from the lower body.
3/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Remove O-ring seal (17) from the lower body.
NOTE: It is not necessary to install the barrel over the same pistons at assembly so identification on
the barrel and pistons is not necessary.
10. Carefully remove barrel (16) from the pistons.
NOTE: It is necessary to remove tool (B) from the barrel to remove the snap ring and shaft (18).
Install tool (B) on the barrel again as soon as shaft (18) is removed.
11. Use tool (C) to remove the snap ring that holds shaft (18) in place. Remove shaft (18) from the
barrel.
12. Remove spring (20) and tube (19) from shaft (18). Earlier motors do not have spring (20).
The spring on shaft (18) can cause injury if all the tension in the spring
is not released before tool (D) is remove. To prevent injury be sure all
the tension in the spring is released before tool (D) is removed from the
shaft.
4/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 13. Use tool (D) and a 5/16" bolt at least 61/2 inches long with a nut and washers to put the spring in
compression so the snap ring can be removed from the groove in shaft (18). Use tool (E) to remove
the snap ring from the groove. Carefully loosen the bolt in tool (D) to release all the tension in the
spring. Remove tool (D) after the tension in the spring is released.
14. Remove snap ring (23), retainer (22), races (21) and bearing (26), spring (24) and race (25) from
shaft (18).
15. Use tool (F) to remove the snap ring that holds the bearing race on shaft (18).
16. Use tooling (G) as shown to remove race (27) from the end of shaft (18).
5/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 17. Use tool (H) to remove snap ring (28) from the barrel.
18. Use tooling (J) and a press to remove the bearing from the barrel (16).
NOTICE
Links (30) must be installed in the same inserts in drive plate (31) they
are removed from so put identification on links (30) as to their location
in drive plate (31). Be extra careful not to damage the highly finished
surfaces of the pistons.
19. Use tool (C) to remove snap rings (29) that hold links (30) in position on drive plate (31).
Remove the piston assemblies from the drive plate.
NOTICE
Pistons (32) must be installed on the same links they are removed from
so put identification on the pistons and links.
6/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 20. Use tool (K) to remove snap ring (34) from piston (32). Remove piston (32), retainer (33), snap
rings (34), (29) and retainer (35) from the link. Disassemble the remainder of the piston assemblies.
21. Remove the bolts that hold retainer (36) to the body and use screwdrivers in notches (37) to
remove the retainer from the body. On earlier motors, two 5/16"-18 NC forcing screws can be used
to remove the retainer.
22. Remove seal (38) and O-ring seal (39) from the retainer.
23. Fasten tool (L) to a work bench, over a hole that is 2.50 in. (63.5 mm) in diameter.
24. Use two 3/4"-10 NC forged eyebolts and fasten a hoist to body (42). Remove the body from the
bracket of tooling (A). The weight of the body is 80 lb. (36 kg).
25. Put body (42) in position on tool (L) as shown. Make sure pin (40) is engaged with the notch
(groove) on the outside diameter of drive plate (31).
7/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 26. Bend the tab of the lock from spanner nut (41).
NOTICE
When tool (M) is used to loosen the spanner nut, be sure the teeth on
the spanner socket do not engage in the teeth of the lock.
27. Use tool (M) to remove the spanner nut from the drive plate.
28. Remove shims (43) from the drive plate.
8/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 29. Put body (42) in a press with a support under the body so drive plate (31) can be pushed out the
bottom of the body. Put tool (N) on the end of drive plate (31) and push the drive plate out of the
body. Do not let the drive plate fall when it is free of the smaller bearing cone in body (42).
30. Remove the smaller bearing cone from body (42).
31. Use tooling (O) to remove the smaller bearing cup from body (42).
32. Use tooling (O) to remove the larger bearing cup from body (42).
33. Use a hammer and punch to push the roll pin in drive plate (31) into the joint assembly inside the
drive plate.
34. Use tool group (J) and a press to push joint assembly (44) out of drive plate (31). Do not let the
joint assembly fall when it is free of the drive plate.
35. Remove the roll pin from joint assembly (44).
9/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 36. Use tooling (P) and a press to push drive plate (31) out of bearing cone (45). The pins of tooling
(P) are installed through the holes in drive plate (31) as support for bearing cone (45).
37. If necessary, use a press to push inserts (46) out of the drive plate.
Assemble Swing And Track Motors
1. Thoroughly clean all parts before assembly. Put a small amount of hydraulic oil on all parts
before assembly.
10/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Lower the temperature of (chill) the two bearing cups for body (1) for two hours minimum.
3. Install the two bearing cups in the body.
NOTICE
Do not turn the body over to install the second bearing cup until the
first bearing cup is warm.
4. After the bearing cups are at ambient (atmospheric) temperature, put body (1) in a press. Use tool
(A) and the press to put a force of 7 ton (63 kN) on the small bearing cup to push the bearing cup
against its seat.
5. Turn the body over and use tool (B) and the press to put a force of 9 ton (81 kN) on the large
bearing cup to push the bearing cup against its seat.
6. Lower the temperature of inserts (2) and use a press to install the inserts in drive plate (3).
11/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 7. Heat bearing cone (4) to a maximum temperature of 275°F (135°C) for a minimum of one hour.
Install the bearing cone on drive plate (3).
NOTICE
Push on only the inner race of bearing cone (4).
8. After bearing cone (4) has become cool use tool (C), spacer (5) and a press to put a force of 9 ton
(81 kN) on the bearing cone to push the bearing cone against its seat on drive plate (3).
NOTE: The bearing cups and cone must be installed correctly to get a correct bearing adjustment
when assembled.
9. Put joint assembly (6) in position inside the drive plate with pin hole (7) in alignment with the
hole in the drive plate. Use tooling (D) and a 5/8"-11 NC bolt 5 1/2 in. long to pull the joint
assembly into position.
12/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 10. Install pin (8) to hold joint assembly (6) in place.
11. Heat small bearing cone (9) to a maximum temperature of 275°F (135°C) for a minimum of one
hour. Install the small bearing cone on the drive plate.
12. Install a 1"-14 NF bolt six inches long with a nut and washer on tooling (E). Use tooling (E) to
make sure the small bearing cone is installed all of the way on the drive plate.
13. Fasten tool (F) to a work bench, over a hole that is 2.50 in. (63.5 mm) in diameter.
14. Put body (1) in position on tool (F). Make sure pin (10) is engaged with the notch (groove) on
the outside diameter of the drive plate.
13/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 15. Install the spanner nut on the drive plate with the finished face down. Install a 5/16"-18 NC bolt
1/2 in. long in body (1). The bolt is used with tool (G) to turn the body. Install tool (G) with the
correct socket on the 5/16 in. bolt so the centerline of tool (G) is toward the center of the body as
shown.
16. Use tool (H) to tighten the spanner nut while body (1) is turned with tool (G). Tighten the
spanner nut until the torque needed to keep body (1) in rotation is 4 to 9 lb.in. (0.4 to 1 N·m).
NOTE: Tool (G) is a lb.in. (N·m) torque wrench that is 8 in. (20.3 cm) long. For other lb.in. torque
wrenches, the correct torque indication can be found with this formula:
C = A x T / A + B
"C" is the torque wrench reading.
"A" is the length of the torque wrench.
"B" is the distance from the center of the wheel to the wheel stud.
"T" is torque on bearings [T = 5 to 12 lb.in. (0.6 to 1.3 N·m)].
17. Hit the end of the drive plate with a soft faced hammer to push the bearing cone against the
spanner nut.
18. Put the body in a vise with the drive plate in a horizontal position.
19. Install tooling (J) as shown to check the end clearance in the bearings.
20. Push on the handle of tooling (J) and turn the drive plate backward and forward in each
direction. Put the indicator on zero.
21. Pull on the handle of tooling (J) and turn the drive plate backward and forward in each direction.
The indicator will show the total end clearance. The end clearance must be .0005 to .002 in. (0.013
to 0.050 mm).
NOTE: Steps 17 through 21 are done to check the bearing setting made in Step 16.
14/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 22. Find the thickness of the shim pack as follows:
a) Use tool (K) to measure the distance from the end of drive plate (3) to the face of the inner race of
bearing cone (9).
b) Use tool (K) to measure the distance from the end of drive plate (3) to step (11) on the drive plate.
c) Subtract the distance found in Step (a) from the distance found in Step (b). The difference will be
the thickness of the shim pack. Measure the thickness of the shim pack with a micrometer.
23. Install shim pack (12) on the drive plate.
24. Install lock (13) on the drive plate.
15/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 25. Install spanner nut (14) on drive plate (3) with the finished face down. Use tool (H) to tighten the
spanner nut to a torque of 400 lb.ft. (540 N·m).
26. Check the torque needed to turn the body again as in Step 16. The torque must be the same.
27. When the correct values of end play and rotation torque are found, bend one ear of lock (13) to
hold the spanner nut tight.
28. Fasten adapter and bracket (15), part of tooling (L), to body (1) as shown, with three 3/4"-10 NC
bolts 2 1/4 inches long. Fasten a hoist and put the body in position on the engine stand of tooling
(L). Weight of the body is 80 lb. (36 kg).
29. Install the lip type seal in retainer (17) with tool (D) and a 1"-14 NF bolt six inches long with a
nut and washer. Install the seal with the lip up as shown. Install O-ring seal (16) on the retainer. Put
clean oil on the seals.
16/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 30. Install retainer (17) in body (1) as shown.
31. Install retainer (23), snap ring (22), snap ring (21) and retainer (19) on link (20). Install piston
(18) on the same link it was removed from and install retainer (19) and snap ring (21) to hold the
piston on the link. Assemble the remainder of the piston assemblies.
32. Install the piston assemblies in their original position on the drive plate. Install the retainers and
use tool (M) to install snap rings (22) in the drive plate that holds the piston assemblies in place.
NOTE: Make sure the protective plate (P) is put in position on the barrel face when work on or near
the barrel is done.
33. Put barrel (25) under a press. Push bearing (24) into the barrel with tool group (N).
34. Use tool (O) to install the snap ring in the barrel to hold the bearing in place.
17/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 35. Use a press and two 3/4" flat washers (26) to push race (27) on shaft (28).
36. Use tool (Q) to install snap ring (29) to hold the bearing race on shaft (28).
37. Install one race (30), spring (34), another race (30), bearing (33), the last race (30), retainer (32)
and snap ring (31) on shaft (28). Snap ring (31) can not be installed in its groove until tooling (R) is
used to put spring (34) in compression.
NOTICE
When the bolt in tooling (R) is tightened to put the spring in
compression, be sure the ear on retainer (32) is in alignment with the
groove in the shaft.
18/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 38. Use tool (R) and a 5/16" bolt at least 6 1/2 inches long with a nut and washers to put the spring
in compression so snap ring (31) can be installed in the groove in shaft (28). Use tool (S) to install
the snap ring in the groove.
Spring (34) on the shaft can cause injury if snap ring (31) is not
completely engaged in the groove in the shaft before tool (S) is removed.
To prevent injury be sure the snap ring is completely engaged in the
groove and carefully remove tool (R).
39. Carefully loosen the bolt in tool (R) until snap ring (31) holds the spring in compression.
Remove tool (R).
40. Install shaft (28) in the barrel (25).
41. Use tool (O) to install the snap ring in barrel (25) to hold shaft (28) in place.
42. Install the barrel over the joint assembly with wide tooth (36) in the barrel in alignment with
wide groove (35) in the joint assembly.
43. Install the barrel the remainder of the way over the pistons.
19/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 44. Install O-ring seal (38) on the lower body and put clean oil on it.
45. Install upper body (37) in its original position on the lower body. Tighten the bolts that hold the
upper body to the lower body to a torque of 65 ± 5 lb.ft. (90 ± 7 N·m).
46. Install O-ring seal (40) on the body and put clean oil on it. Remove tool (P) from the barrel and
put clean oil on the face of the barrel.
47. Install two 1/2" - 13 NC guide bolts in the upper body. Install pump head (39) in its original
position on the upper body and install the bolts that hold it in place. Tighten the bolts to a torque of
65 ± 5 lb.ft. (90 ± 7 N·m).
48. Install tube (42) and spring (41) in the shaft. Be sure the tube is against its seat in the shaft.
When the tube is correctly against its seat, the spring will be approximately .625 in. (15.88 mm)
down from the top of the shaft.
NOTE: Earlier motors do not have spring (41) and tube (42) is longer.
20/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 49. Turn shaft (28) so the groove in the shaft is in alignment with the groove in the pump head.
50. Install retainer (43) with the pin in the retainer in alignment with the hole made by shaft (28) and
the groove in the pump head. Install the lock and bolt that hold retainer (43) in place.
51. Assemble the shuttle valve for earlier motors as follows:
a) Install a ring (44) and seal (45) on each of stops (47).
b) Install pin (48) and a ball (46) on each side of the pin in the valve body.
c) Install stops (47) in each end of the valve body.
d) Install the plugs and locks to hold stops (47) in place.
e) Install O-ring seal (49) in the valve body.
52. Assemble the shuttle valve for later motors as follows:
a) Install O-ring seals (51) on plugs (50).
b) Install a ball (52) and plug (50) in one side of the valve body.
c) Install pin (53), a ball (52) and plug (50) in the other side of the valve body.
d) Install O-ring seals (54) and (55) on the valve body.
53. Put shuttle valve (56) in position on the motor and install the bolts that hold it in place.
21/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 54. Remove the plug from the side of the upper body and fill the track motor with clean oil. Install
the plug.
55. Fasten a hoist to the bracket and remove the bracket and track motor from the engine repair
stand. Weight of the track motor is 210 lb. (95 kg).
56. Remove the bracket from the track motor.
end by:
a) install track motors
b) install swing motor
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 8 11:32:21 UTC+0800 2019
22/22
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 82X
Configuration: 245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
245 EXCAVATOR VEHICLE SYSTEMS
Media Number -SENR7339-02 Publication Date -01/01/1983 Date Updated -12/10/2001
Swing Brake
SMCS - 5460-16; 5460-15
Disassemble Swing Brake
start by:
a) remove swing motor
1. Remove bolts from swing brake housing.
2. Remove the swing brake housing (1).
3. Remove brake drum (2).
NOTE: The control lever for the swing brake must be in the "OFF" position to remove the brake
drum.
4. Disconnect the brake linkage from lever (3).
1/2
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 5. Remove bolts (4) that hold plate to bearing cage.
6. Remove plate, linings and lever as a unit.
7. Remove springs and linings from plate.
Assemble Swing Brake
1. Install linings (1) and springs (3) on plate (2).
2. Put lever in position and install plate and linings.
3. Install bolts that hold plate (2) to bearing cage.
4. Install brake drum (5).
5. Connect the brake linkage to lever (4).
6. Install swing brake housing.
end by:
a) install swing motor
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 8 11:33:17 UTC+0800 2019
2/2
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...