The document provides instructions for removing and installing fuel system components on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the fuel priming pump by disconnecting tubes and removing mounting bolts. It also details removing the fuel filter base by disconnecting fuel lines and removing mounting bolts. Finally, it explains removing the fuel transfer pump by disconnecting tubes and removing mounting bolts.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures describe draining fuel, removing bolts and tubes, and installing replacement parts like gaskets and seals. Safety notices recommend keeping parts clean and containing fluids during maintenance.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, checking for worn gaskets, applying new seals and gaskets, and reinstalling components along with reconnecting fuel lines. Detailed illustrations are provided to identify the specific components and correct installation order. Safety notices recommend keeping parts clean and containing fluids during maintenance work.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures describe draining fuel, removing bolts and tubes, and installing replacement parts like gaskets and seals. Safety notices recommend keeping parts clean and containing fluids during maintenance.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, checking for worn gaskets, applying new seals and gaskets, and reinstalling components along with reconnecting fuel lines. Detailed illustrations are provided to identify the specific components and correct installation order. Safety notices recommend keeping parts clean and containing fluids during maintenance work.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and disassembling components of the fuel transfer pump for a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing the fuel transfer pump by disconnecting tubes and removing bolts.
- Disassembling the pump housing by removing the cover, spring, seals, valve assemblies, piston, sleeve, seals and bolts.
- Instructions specify cleaning parts and containing fluids during maintenance.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...xiapokang564341
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include illustrations showing the component locations and parts, and provide notices about cleaning parts and containing fluids. Removal and installation procedures are provided in step-by-step format.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...hvy7sbkw8e
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean all parts and contain fluids during repair or maintenance following the manufacturer's guidelines.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...wenxian17880
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean all parts and contain fluids during repair or maintenance following the manufacturer's guidelines.
This service manual document provides instructions for repairing and assembling components of a 225 excavator powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The document provides detailed step-by-step instructions and illustrations for each procedure, with notices about keeping parts clean and containing fluids.
This service manual document provides instructions for repairing and assembling components of a 225 excavator powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The document provides detailed step-by-step instructions and illustrations for each procedure, as well as safety notices to properly contain fluids and prevent contamination.
The document provides instructions for removing and installing components of the fuel system for a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump into its individual components
The instructions include safety notices and illustrations showing the component locations and removal/installation steps.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...uujjfjjkskmme
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235B Excavator. It describes:
1) Removing the fuel transfer pump by disconnecting tubes and removing bolts.
2) Disassembling the pump by removing covers, springs, seals, pistons, sleeves, and valves.
3) The document emphasizes cleanliness and containing fluids during maintenance.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...fujsefjfkksekem
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235B Excavator. It describes:
1) Removing the fuel transfer pump by disconnecting tubes and removing bolts.
2) Disassembling the pump by removing covers, springs, seals, pistons, sleeves, and valves.
3) The document emphasizes cleanliness and containing fluids during maintenance.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...yhfhjjkdksmme
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by disconnecting hoses and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting lines and removing mounting bolts. It is installed by reversing the removal steps and replacing any worn gaskets.
- The fuel transfer pump, which is removed by disconnecting inlet and outlet lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...fujsjefskekmm
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps after checking and replacing gaskets if needed.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Detailed steps are provided to disassemble and reassemble the fuel transfer pump components.
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components.
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
More Related Content
Similar to Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03764).pdf
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump, fuel filter base, and fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. The procedures include draining fuel, removing bolts and connections, installing new gaskets if needed, reconnecting lines and bolting components back into place. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and disassembling components of the fuel transfer pump for a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing the fuel transfer pump by disconnecting tubes and removing bolts.
- Disassembling the pump housing by removing the cover, spring, seals, valve assemblies, piston, sleeve, seals and bolts.
- Instructions specify cleaning parts and containing fluids during maintenance.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...xiapokang564341
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include illustrations showing the component locations and parts, and provide notices about cleaning parts and containing fluids. Removal and installation procedures are provided in step-by-step format.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...hvy7sbkw8e
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean all parts and contain fluids during repair or maintenance following the manufacturer's guidelines.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03...wenxian17880
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean all parts and contain fluids during repair or maintenance following the manufacturer's guidelines.
This service manual document provides instructions for repairing and assembling components of a 225 excavator powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The document provides detailed step-by-step instructions and illustrations for each procedure, with notices about keeping parts clean and containing fluids.
This service manual document provides instructions for repairing and assembling components of a 225 excavator powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The document provides detailed step-by-step instructions and illustrations for each procedure, as well as safety notices to properly contain fluids and prevent contamination.
The document provides instructions for removing and installing components of the fuel system for a Caterpillar 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling the fuel transfer pump into its individual components
The instructions include safety notices and illustrations showing the component locations and removal/installation steps.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...uujjfjjkskmme
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235B Excavator. It describes:
1) Removing the fuel transfer pump by disconnecting tubes and removing bolts.
2) Disassembling the pump by removing covers, springs, seals, pistons, sleeves, and valves.
3) The document emphasizes cleanliness and containing fluids during maintenance.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...fujsefjfkksekem
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235B Excavator. It describes:
1) Removing the fuel transfer pump by disconnecting tubes and removing bolts.
2) Disassembling the pump by removing covers, springs, seals, pistons, sleeves, and valves.
3) The document emphasizes cleanliness and containing fluids during maintenance.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...yhfhjjkdksmme
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by disconnecting hoses and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting lines and removing mounting bolts. It is installed by reversing the removal steps and replacing any worn gaskets.
- The fuel transfer pump, which is removed by disconnecting inlet and outlet lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 235 b excavator (prefix 4ed) service repair manual (4ed00001 ...fujsjefskekmm
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3306 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps after checking and replacing gaskets if needed.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Detailed steps are provided to disassemble and reassemble the fuel transfer pump components.
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components.
The document provides instructions for removing and disassembling fuel system components on a Caterpillar 3306 engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing securing bolts and disconnecting tubes.
- Removing the fuel filter base by turning off the fuel supply, disconnecting lines, and removing bolts and washers.
- Removing the fuel transfer pump by turning off the fuel supply, disconnecting tubes, and removing securing bolts.
- Disassembling the fuel transfer pump by removing covers, springs, seals, valves, pistons, sleeves, and other internal components.
Similar to Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U02729-03764).pdf (20)
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix MAB) Service Repair Manual (MAB00001...f8usjejkdmmd
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows the retaining nut to be safely removed with a hydraulic cylinder, releasing the compressed spring.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00984196
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00500957
1. Turn the fuel supply line valve to the OFF position.
2. Remove the bolts and the washers that secure fuel priming pump (1) to base (5). Remove
gasket (4) .
3. Disconnect tube assembly (3) .
4. Remove two bolts (2), the washers and base (5) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00500957
2/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Install base (5), the washers and two bolts (2) .
2. Connect tube assembly (3) to base (5) .
Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
3. Install gasket (4). Install fuel priming pump (1) and the bolts that secure the fuel priming
pump to base (5) .
4. Turn the fuel supply line valve to the ON position.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:42:46 UTC+0800 2019
3/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00917143
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
1/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00468389
1. Use Tool (A) to remove fuel filter (4) .
2. Disconnect fuel line (1) from fuel filter base (2) .
3. Remove two bolts (3), the washers, fuel filter base (2) and the gasket from the fuel injection
pump housing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g00468389
Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
1. Install the gasket, fuel filter base (2), the washers and two bolts (3) on the fuel injection
pump housing.
2. Connect fuel line (1) to fuel filter base (2) .
3. Use Tool (A) to install fuel filter (4) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:43:42 UTC+0800 2019
3/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00905874
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00462112
1. Turn the fuel supply line valve to the OFF position.
2. Remove tube assembly (2) and tube assembly (4) from fuel transfer pump (3) .
3. Remove bolts (1) and (5) from fuel transfer pump (3). Remove fuel transfer pump (3) and
the O-ring seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:44:38 UTC+0800 2019
2/2
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01003268
Fuel Transfer Pump - Disassemble
SMCS - 1256-015
Disassembly Procedure
Start By:
A. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00498289
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1. Remove bolts (2) and cover (1) from the fuel transfer pump housing.
Illustration 2 g00499040
2. Remove spring (4) from housing (3) .
2/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00498980
3. Remove O-ring seals (5) and (6) from cover (1) .
4. Remove valve assembly (7) from cover (1) .
Illustration 4 g00498334
5. Remove piston (12) from sleeve (10). Remove washer (15), valve assembly (14) and seal
(13) from piston (12) .
6. Remove sleeve (10) from housing (3). Remove O-ring seal (11) from sleeve (10) .
7. Remove guide and tappet assembly (9) and seal (8) from housing (3) .
3/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 5 g00498367
8. Remove two bolts (16), cover (17) and the seal from housing (3) .
Illustration 6 g00498470
9. Remove valve assembly (18) from housing (3) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:45:33 UTC+0800 2019
4/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01003269
Fuel Transfer Pump - Assemble
SMCS - 1256-016
Assembly Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00498470
1. Install valve assembly (18) in housing (3) .
Illustration 2 g00498687
2. Put clean diesel fuel on seal (16). Install seal (16) on cover (17), as shown. Install the two
bolts that hold cover (17) to housing (3) .
Illustration 3 g00498334
2/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. NOTICE
The tappet and guide assembly must be serviced as a unit.
3. Put clean diesel fuel on seal (8). Install seal (8) on guide and tappet assembly (9). Install
guide and tappet assembly (9) in housing (3) .
4. Put clean diesel fuel on O-ring seal (11). Put O-ring seal (11) in position on sleeve (10).
Install sleeve (10) in housing (3) .
5. Install piston (12) in sleeve (10) .
6. Put clean diesel fuel on seal (13). Put seal (13), valve assembly (14) and washer (15) in
position in piston (12) .
Illustration 4 g00498980
7. Put clean diesel fuel on O-ring seals (5) and (6). Install O-ring seals (5) and (6) in cover (1).
Install valve assembly (7) in cover (1) .
3/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g00499040
8. Install spring (4) in housing (3) .
Illustration 6 g00498289
9. Put cover (1) in position on the housing and install bolts (2) that hold the cover in position.
End By: Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:46:29 UTC+0800 2019
4/4
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00906240
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00462112
1. Install the O-ring seal and fuel transfer pump (3). Install bolts (1) and (5) .
2. Install tube assembly (2) and tube assembly (4) .
1/2
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 3. Turn the fuel supply line valve to the ON position.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:47:25 UTC+0800 2019
2/2
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/5
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00448807
1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
Illustration 2 g00448808
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g00448809
3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
Illustration 4 g00448810
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 5 g00475542
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 6 g00475546
4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 12 19:48:20 UTC+0800 2019
5/5
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
225 EXCAVATOR 76U02729-03764 (MACHINE) POWERED BY 3304 ENGINE(H...
2019/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...