This document provides instructions for disassembling and assembling the governor of a Caterpillar 225 EXCAVATOR model. It outlines 34 steps to disassemble parts like the fuel ratio control, housing, springs, pins and levers. It then outlines 23 steps for reassembling parts like the carrier, flyweights, races, bearings, riser, dashpot and governor servo. Tools including retaining ring pliers and drivers are required. Cleanliness is emphasized to prevent contaminant issues.
This document provides instructions for disassembling and assembling the governor of a Caterpillar 225 EXCAVATOR model. It outlines 34 steps to disassemble parts like the fuel ratio control, housing, springs, pins and levers. It then outlines 23 steps for reassembling parts like the carrier, flyweights, races, bearings, dashpot assembly, valve, sleeves and pistons. Precautions are given to keep parts clean and ensure passages are clear during assembly.
Caterpillar cat 966 h wheel loader (prefix a6g) service repair manual (a6g000...fisjejfskemmd
The document provides instructions for disassembling and assembling the piston pump of a 966H wheel loader. It lists 37 steps for disassembly that involve removing components like bolts, seals, springs, pistons, and covers. It then lists 15 steps for assembly that involve installing these same components in the reverse order of disassembly. The instructions include illustrations to clarify the procedure and notes about using specific tools.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 950 h wheel loader (prefix j5j) service repair manual (j5j015...ufjkskemfseol
1. The document provides disassembly and assembly instructions for a piston pump used in a wheel loader.
2. It details 41 steps to disassemble the pump by removing components like the head assembly, piston assemblies, springs, seals, and bearings.
3. Reassembly requires properly installing those same components in reverse order, and includes procedures to set the proper bearing preload using shims and feeler gauges.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The installation procedure specifies applying lubricant to new seals before reconnecting the governor components using the same special tools. Proper tightening torque is listed for bolts reinstalling the fuel injection control linkage.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
This document provides instructions for disassembling and assembling the governor of a Caterpillar 225 EXCAVATOR model. It outlines 34 steps to disassemble parts like the fuel ratio control, housing, springs, pins and levers. It then outlines 23 steps for reassembling parts like the carrier, flyweights, races, bearings, dashpot assembly, valve, sleeves and pistons. Precautions are given to keep parts clean and ensure passages are clear during assembly.
Caterpillar cat 966 h wheel loader (prefix a6g) service repair manual (a6g000...fisjejfskemmd
The document provides instructions for disassembling and assembling the piston pump of a 966H wheel loader. It lists 37 steps for disassembly that involve removing components like bolts, seals, springs, pistons, and covers. It then lists 15 steps for assembly that involve installing these same components in the reverse order of disassembly. The instructions include illustrations to clarify the procedure and notes about using specific tools.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 950 h wheel loader (prefix j5j) service repair manual (j5j015...ufjkskemfseol
1. The document provides disassembly and assembly instructions for a piston pump used in a wheel loader.
2. It details 41 steps to disassemble the pump by removing components like the head assembly, piston assemblies, springs, seals, and bearings.
3. Reassembly requires properly installing those same components in reverse order, and includes procedures to set the proper bearing preload using shims and feeler gauges.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The installation procedure specifies applying lubricant to new seals before reconnecting the governor components using the same special tools. Proper tightening torque is listed for bolts reinstalling the fuel injection control linkage.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...xiapokang564341
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It describes 34 steps to disassemble the governor and 28 steps to reassemble it. The disassembly process involves removing housing components, springs, levers, pins, and other internal parts. The assembly process describes installing these parts in reverse order and adjusting components like collars and stop screws. Precise tools are required and cleanliness is emphasized throughout to prevent contaminants from causing wear.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...hvy7sbkw8e
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It outlines 34 steps to disassemble the governor and its components. This includes removing housing, springs, pins, plates, screws, seals, and other parts. It then outlines 31 steps for reassembling the governor, reversing the disassembly process and ensuring all parts are clean and lubricated before reinstalling. Precise positioning and proper tool usage is required for assembly.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...wenxian17880
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly, removing parts like the fuel ratio control, housing, springs, levers, pins, and more. It then lists 23 steps for assembly, installing parts like races, bearings, springs, sleeves, pins, and torque control components in the reverse order of disassembly. Tools required include various drivers, pliers, and clamps. Cautions are provided to keep parts clean and check seals and gaskets when reassembling.
This document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It includes 44 steps to disassemble the travel motor along with illustrations showing how to remove components like covers, seals, valves, plates, and assemblies. The assembly section includes matching steps and illustrations for reinstalling components in the reverse order. Tools required are also listed.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil before reinstalling components.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjsjjefskekkme
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, involving removing housing components, valves, seals, springs, pins, and other internal parts. It then lists 26 steps for reassembly, putting the components back in reverse order, and noting the importance of cleanliness. Tools required include retaining ring pliers, a slide hammer puller, bearing puller, and link brackets for lifting components.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjsekdemmd
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It begins with a list of required tools and safety notes. The disassembly procedure has 48 steps that remove components like valves, springs, seals, pistons, and shafts. The assembly procedure reverses these steps and provides additional safety warnings. It aims to fully disassemble and then reassemble the travel motor while maintaining cleanliness.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...udfjjdjkkmds
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, involving removing housing components, valves, seals, springs, pins, and other internal parts. It then lists 26 steps for reassembly, putting the components back in reverse order, ensuring proper installation of seals, springs, and other precision parts. Tools required include retaining ring pliers, a slide hammer puller, bearing puller, and link brackets for lifting components. Cleanliness is emphasized to prevent dirt contamination of internal parts.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fusjjefjskekemm
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, which include removing housing components, valves, seals, springs, pistons, and the rotor assembly. It then lists 26 steps for assembly, which involve installing these same components in reverse order. Precautions are provided regarding cleaning parts and maintaining clean work areas to prevent damage from contaminants. Required tools are also listed.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjksekmdme
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It begins with a list of required tools and safety notes. The disassembly procedure has 48 steps that remove components like valves, springs, seals, pistons, and shafts. The assembly section then lists 29 steps to reinstall these components in the reverse order, also providing safety notes and instructions to clean parts and control temperatures. Precise procedures and illustrations are provided to take the travel motor apart and rebuild it piece-by-piece.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...cfvdssd
This document provides instructions for disassembling and assembling the front axle of an M315C wheeled excavator. It includes 27 steps to disassemble components like the carrier housing, planetary gears, ring gear assembly, hub and bearings. It also includes 18 steps to reassemble these components, providing details on cleaning, inspecting and installing seals, bearings, springs and other parts. Tools required are listed. Safety warnings are provided regarding hydraulic pressure, heavy components and spring forces.
This document provides instructions for disassembling and assembling the front axle of an M315C wheeled excavator. It includes 27 steps to disassemble components like the carrier housing, planetary gears, ring gear assembly, hub and bearings. It also includes 18 steps to reassemble these components, providing details on cleaning, inspecting and installing seals, bearings, springs and other parts. Tools required are listed. Safety warnings are provided regarding hydraulic pressure, heavy components and spring forces.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjkskedmme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components, providing details on cleaning, lubricating and torque specifications. Precise assembly is needed to properly rebuild the front axle.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
The document provides instructions for disassembling and assembling various components of the final drive, carriers, hubs, and brakes on the front and rear axles of a M316D Wheeled Excavator. The disassembly process involves removing 22 components from the front axle and 23 components from the rear axle. The assembly instructions list applying anti-seize compound and installing bearings, seals, gears, carriers, and other parts in the reverse order of disassembly. Tools including retaining ring pliers, drivers, spanners, and pullers are required. Safety notices remind technicians to contain fluids and release spring forces carefully.
Caterpillar cat m316 d wheeled excavator (prefix p6k) service repair manual (...ufusejkksemm
This document provides disassembly instructions for the final drive carriers, hubs, and brakes of the front and rear axles of a M316D Wheeled Excavator. It lists the required tools and presents a step-by-step process for disassembling components such as the carrier housing, planetary gears, ring gear housing, pistons, discs, gears, bearings, seals, and other parts. Safety notices are included to handle fluids and release spring forces properly during disassembly. Detailed illustrations supplement each step in the procedures.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...uuudfjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 320 excavator, including:
1) The turbocharger, exhaust manifold, air inlet heater, and inlet manifold. Detailed steps are given to remove each part, inspect gaskets, and reinstall the parts in reverse order.
2) Specific torque specifications and notes are provided about checking gasket conditions and using replacement gaskets if needed.
3) References to other removal and installation documents are listed to complete related component work.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...uuudfjjskkemmd
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
More Related Content
Similar to Caterpillar cat 225 excavator (prefix 76 u) service repair manual (76u00694 01199)
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...xiapokang564341
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It describes 34 steps to disassemble the governor and 28 steps to reassemble it. The disassembly process involves removing housing components, springs, levers, pins, and other internal parts. The assembly process describes installing these parts in reverse order and adjusting components like collars and stop screws. Precise tools are required and cleanliness is emphasized throughout to prevent contaminants from causing wear.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...hvy7sbkw8e
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It outlines 34 steps to disassemble the governor and its components. This includes removing housing, springs, pins, plates, screws, seals, and other parts. It then outlines 31 steps for reassembling the governor, reversing the disassembly process and ensuring all parts are clean and lubricated before reinstalling. Precise positioning and proper tool usage is required for assembly.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00694-01...wenxian17880
This document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly, removing parts like the fuel ratio control, housing, springs, levers, pins, and more. It then lists 23 steps for assembly, installing parts like races, bearings, springs, sleeves, pins, and torque control components in the reverse order of disassembly. Tools required include various drivers, pliers, and clamps. Cautions are provided to keep parts clean and check seals and gaskets when reassembling.
This document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It includes 44 steps to disassemble the travel motor along with illustrations showing how to remove components like covers, seals, valves, plates, and assemblies. The assembly section includes matching steps and illustrations for reinstalling components in the reverse order. Tools required are also listed.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil before reinstalling components.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjsjjefskekkme
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, involving removing housing components, valves, seals, springs, pins, and other internal parts. It then lists 26 steps for reassembly, putting the components back in reverse order, and noting the importance of cleanliness. Tools required include retaining ring pliers, a slide hammer puller, bearing puller, and link brackets for lifting components.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjsekdemmd
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It begins with a list of required tools and safety notes. The disassembly procedure has 48 steps that remove components like valves, springs, seals, pistons, and shafts. The assembly procedure reverses these steps and provides additional safety warnings. It aims to fully disassemble and then reassemble the travel motor while maintaining cleanliness.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...udfjjdjkkmds
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, involving removing housing components, valves, seals, springs, pins, and other internal parts. It then lists 26 steps for reassembly, putting the components back in reverse order, ensuring proper installation of seals, springs, and other precision parts. Tools required include retaining ring pliers, a slide hammer puller, bearing puller, and link brackets for lifting components. Cleanliness is emphasized to prevent dirt contamination of internal parts.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fusjjefjskekemm
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps for disassembly, which include removing housing components, valves, seals, springs, pistons, and the rotor assembly. It then lists 26 steps for assembly, which involve installing these same components in reverse order. Precautions are provided regarding cleaning parts and maintaining clean work areas to prevent damage from contaminants. Required tools are also listed.
Caterpillar cat m318 c wheeled excavator (prefix h2d) service repair manual (...fjksekmdme
The document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It begins with a list of required tools and safety notes. The disassembly procedure has 48 steps that remove components like valves, springs, seals, pistons, and shafts. The assembly section then lists 29 steps to reinstall these components in the reverse order, also providing safety notes and instructions to clean parts and control temperatures. Precise procedures and illustrations are provided to take the travel motor apart and rebuild it piece-by-piece.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...cfvdssd
This document provides instructions for disassembling and assembling the front axle of an M315C wheeled excavator. It includes 27 steps to disassemble components like the carrier housing, planetary gears, ring gear assembly, hub and bearings. It also includes 18 steps to reassemble these components, providing details on cleaning, inspecting and installing seals, bearings, springs and other parts. Tools required are listed. Safety warnings are provided regarding hydraulic pressure, heavy components and spring forces.
This document provides instructions for disassembling and assembling the front axle of an M315C wheeled excavator. It includes 27 steps to disassemble components like the carrier housing, planetary gears, ring gear assembly, hub and bearings. It also includes 18 steps to reassemble these components, providing details on cleaning, inspecting and installing seals, bearings, springs and other parts. Tools required are listed. Safety warnings are provided regarding hydraulic pressure, heavy components and spring forces.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjkskedmme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components, providing details on cleaning, lubricating and torque specifications. Precise assembly is needed to properly rebuild the front axle.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
The document provides instructions for disassembling and assembling various components of the final drive, carriers, hubs, and brakes on the front and rear axles of a M316D Wheeled Excavator. The disassembly process involves removing 22 components from the front axle and 23 components from the rear axle. The assembly instructions list applying anti-seize compound and installing bearings, seals, gears, carriers, and other parts in the reverse order of disassembly. Tools including retaining ring pliers, drivers, spanners, and pullers are required. Safety notices remind technicians to contain fluids and release spring forces carefully.
Caterpillar cat m316 d wheeled excavator (prefix p6k) service repair manual (...ufusejkksemm
This document provides disassembly instructions for the final drive carriers, hubs, and brakes of the front and rear axles of a M316D Wheeled Excavator. It lists the required tools and presents a step-by-step process for disassembling components such as the carrier housing, planetary gears, ring gear housing, pistons, discs, gears, bearings, seals, and other parts. Safety notices are included to handle fluids and release spring forces properly during disassembly. Detailed illustrations supplement each step in the procedures.
Similar to Caterpillar cat 225 excavator (prefix 76 u) service repair manual (76u00694 01199) (20)
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...uuudfjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 320 excavator, including:
1) The turbocharger, exhaust manifold, air inlet heater, and inlet manifold. Detailed steps are given to remove each part, inspect gaskets, and reinstall the parts in reverse order.
2) Specific torque specifications and notes are provided about checking gasket conditions and using replacement gaskets if needed.
3) References to other removal and installation documents are listed to complete related component work.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...uuudfjjskkemmd
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...uuudfjjskkemmd
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uuudfjjskkemmd
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Reinstalling covers and connecting remaining hoses after installation is complete.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...uuudfjjskkemmd
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B or 3306B engine. The removal procedure involves removing various lines, bolts, tubes and the housing itself from the engine. The disassembly of the housing includes removing the cover, fuel rack, lifters, camshaft and bearings. The assembly procedure outlines installing new or original bearings, camshaft, washer, snap ring, lifters and fuel rack back into the housing.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)uuudfjjskkemmd
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and lists the steps to remove components like the rear housing, brushes, field windings, and more. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualuuudfjjskkemmd
The document provides instructions for disassembling three types of starting motors used in Caterpillar excavators:
1) The 42-MT starting motor can be disassembled by removing wiring, housing bolts, brushes, and internal components like the armature and field windings.
2) The 37-MT and 41-MT motors are disassembled similarly, by removing wiring, housings, brushes, and internal parts.
3) Detailed steps and illustrations guide the removal of over 30 individual parts in sequential order.
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. The removal process involves disconnecting nuts and brackets to remove the lines and using special tools to pull nozzles while preventing them from turning. Installation requires cleaning parts, adding new seals, and reconnecting lines and brackets while applying specified torques. Proper alignment of notches and tabs is important when reinstalling nozzles.
This document provides instructions for disassembling the piston motor of a 216B3 skid steer loader. It outlines 25 steps to disassemble the various components of the piston motor, including removing nuts, valves, springs, seals, housings, pistons, bearings, and other parts. Precautions are provided to wear protective equipment when removing parts with spring forces. Various specialized tools are listed that are required for the disassembly process.
Case ih puma 220 tier 4 b (final) tractor service repair manualuuudfjjskkemmd
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 921 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document is a service manual for a 921E wheel loader. It contains sections covering general information, engines, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment. Each section provides removal and installation instructions for components, specifications, troubleshooting information, and other repair details. The manual also includes torque specifications, fluid and lubricant information, and electrical and hydraulic schematic foldouts in the rear.
Case 821 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 33 steps for removing components to separate the engine from the rest of the machine, including draining fluids, disconnecting wiring harnesses, hoses and other connections, and removing mounting hardware. The overall process removes parts and accessories to fully separate the engine for removal while tagging components and connections for reinstallation.
Case 721 g xt eh, new cab tier2 wheel loader service repair manual [fnh0721...uuudfjjskkemmd
This document is a service manual for wheel loaders models 621G and 721G. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for technicians, and stresses the importance of following all safety precautions when working on the equipment.
Case 721 f xt wheel loader service repair manualuuudfjjskkemmd
This document is a service manual for a wheel loader model 721F. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork, and decals. Safety precautions are provided, noting hazards that could result in death, serious injury, or machine/property damage. Only authorized personnel should perform repairs or maintenance.
Case 721 f tier 4 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a 721F wheel loader. The main steps include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting bolts. Safety precautions are described such as releasing pressure from hydraulic and brake systems. Key components removed are the radiator, hood, air intake components, exhaust, and belt cover. Proper lifting and support equipment is required.
Case 721 e eu wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing and installing the engine and radiator on a 721E wheel loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an engine lift to remove the engine from the loader. Engine installation is the reverse of removal. Radiator removal requires draining the coolant and removing mounting bolts, hoses and fans. Radiator installation is the reverse of removal.
Case 721 e tier 3 wheel loader service repair manualuuudfjjskkemmd
This document provides instructions for removing the engine from a wheel loader. It is a service manual section that lists 33 steps for disconnecting all electrical, cooling, air, and structural components that connect the engine to the rest of the machine. These include draining fluids, removing hoses, belts, wiring harnesses, and mounting hardware to fully separate the engine for removal.
Case 621 f tier 4 wheel loader service repair manualuuudfjjskkemmd
This document provides a service manual for Case 621F and 721F wheel loaders with Tier 4 engines. It includes torque specifications for various components of the engine, transmission, axles, chassis, cooling, hydraulic, and electrical systems. The document is copyrighted and published by CNH America LLC.
Case 521 g xt new cab tier2 wheel loader service repair manual [fnh0521gnghe0...uuudfjjskkemmd
This service manual provides information on servicing a 521G wheel loader. It covers maintenance and repair procedures for the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, electrical systems, front loader, bucket, and bodywork. Safety precautions are outlined to prevent personal injury when working on the machine.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00694-01199 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 6 g00453011
6. Remove shaft assembly (15) and levers (14) and (13) .
Illustration 7 g00453012
7. Remove two snap rings (19) from two pins (17). Remove two pins (17). Remove plates (16)
and stop (18) .
Illustration 8 g00453014
8. Remove pins (21) and (22) and remove spring (20) .
4/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 9 g00453015
9. Remove two bolts (23), and the washers, and remove adapter (24), the coupling, and the O-
ring seal.
10. Remove contact (27) and body (28) with an O-ring seal.
11. Remove two bolts (29) and the washers and remove cover (30) and the gasket.
12. Remove two nuts and washers (26) and remove shutoff solenoid (25) and the gasket.
Illustration 10 g00453016
13. Remove shaft (31) and lever (32) .
5/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 11 g00453017
Note: The check valve will be damaged during removal. Remove check valve (33) only if a
replacement is necessary.
14. Remove check valve (33) only if a replacement is necessary.
Illustration 12 g00453018
15. Remove seal (34) and adjustment screw (35) .
6/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 13 g00453019
16. Remove bolt (36), housing (37) and the gasket from the fuel injection pump housing.
Illustration 14 g00453557
Typical example
17. Remove bolts (38) and remove torque control (39) .
18. Disassemble torque control (39) and inspect the spacer, the spring, and the insulator for
damage or wear. Replace parts that are worn or damaged with new parts.
Illustration 15 g00453558
19. Remove two bolts (40) and block (41) .
7/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 16 g00453559
20. Remove the bolt that holds collar (42) to bolt (44). Remove collar (42), spring (43) and bolt
(44) .
21. Remove the stop screws from collar (42) if the collar needs to be replaced.
Illustration 17 g00453560
22. Remove three bolts (46) and remove governor servo (45). The governor servo must be
rotated in order to be released from the rack's regulator.
8/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 18 g00453632
23. Remove lockring (50), seat (53), link spring (52) and sleeve (51). Remove the other
lockring (50) from the groove in the center of valve (47). Remove valve (47), sleeve (48)
and piston (49). The piston must be pushed down in order to be removed. Remove the O-
ring seal from sleeve (48). Remove pin (55) and lever (56) .
Illustration 19 g00453633
Illustration 20 g00453634
24. Use Tool (A) in order to hold spring (58) compressed for the removal of ring (57). Spring
(58) is used in order to put a preload on the thrust bearing for the camshaft in the fuel
injection pump housing.
25. Remove ring (57) and slowly release Tool (A) .
9/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 21 g00453635
26. Remove bearing (60), sleeves (59) and spring (58) .
Illustration 22 g00453636
27. Remove ring (61) and dashpot assembly (62) .
Illustration 23 g00453637
28. Use Tool (C) in order to remove snap ring (68). Remove ring (67) and spool (66) .
10/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. 29. Remove seat (65) from spring (64) and remove spring (64) from seat (63) .
Illustration 24 g00453665
30. Remove riser (69) .
Illustration 25 g00453667
31. Remove ring (70), races (71) and bearing (72) .
11/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 26 g00453668
32. Remove four bolts (73) and carrier (74) .
Illustration 27 g00453669
33. Remove dowels (77) and flyweights (76). Remove governor shaft (75) and the dowel that is
not shown from shaft (75) .
Illustration 28 g00453670
34. Remove races (78) and bearing (79) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 7 20:06:36 UTC+0800 2019
12/12(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00694-01199 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111261
Governor - Assemble
SMCS - 1264-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
B 6V-2163 Spring Clamp 1
C 1P-0510 Driver Group 1
D 6V-2054 Shield Driver 1
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets, the seals, or any
parts are worn or damaged, use new parts for replacement.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 1 g00453799
1. Install one race (1), bearing (2) and the other race (1) on the camshaft in the fuel injection
pump housing.
Illustration 2 g00453801
2. Put flyweights (4) in position on carrier (3) and install the dowels in order to hold the
flyweights in place. The flyweights must move freely on the dowels.
Illustration 3 g00453802
2/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. 3. Install dowel (5) in governor shaft (6) and install the governor shaft in the carrier (3) .
Illustration 4 g00459340
4. Put carrier (3) in position and install bolts (7) .
Illustration 5 g00459410
5. Install race (9), bearing (10) and race (9). Use Tool (A) in order to install ring (8) on riser
(11) .
3/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. Illustration 6 g00459411
6. Install riser (11) .
Illustration 7 g00459414
7. Assemble the dashpot, as follows:
a. Install spring (13) on seat (12) and install seat (14) in spring (13) .
b. Put spool (15) and ring (16) in position on seat (14) and use Tool (A) in order to
install snap ring (17) .
4/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Illustration 8 g00459416
8. Install dashpot assembly (19). Install ring (18) in the lower groove in the governor shaft.
Illustration 9 g00459419
9. Install sleeve (20), spring (22), sleeve (20) and bearing (21) .
Note: Spring (22) is used in order to put a preload on the thrust bearing on the camshaft in
the fuel injection pump housing.
5/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 10 g00459421
10. Use Tool (B) in order to hold spring (22) compressed and install ring (23) in the groove in
the governor shaft. Remove Tool (B) .
Illustration 11 g00459423
11. Put lever (33) in position on the governor servo and install pin (32) in order to hold the lever
in place. Use a hammer and a chisel in order to move the metal (stake) at four places that are
spread apart 90 degrees. Perform this procedure on the outside surface on both legs of the
governor servo. This helps to hold pin (32) in place.
12. Install the O-ring seal on sleeve (25). Install piston (26) and sleeve (25) .
13. Install valve (24) .
14. Install one lockring (27) in the groove near the center of valve (24). Put sleeve (28), link
spring (29) and seat (30) in position on valve (24) and install second lockring (31) .
Illustration 12 g00454273
15. Put the governor servo in position on the fuel injection pump housing with piston (34) that
is engaged over rack control sleeve (35) and install the bolts that hold the rack control
sleeve in place.
6/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 13 g00591527
3304B engine
Note: The 3304B engine has one stop screw (36) and one locknut (38).
Illustration 14 g00454274
3306B
16. If the stop screws were removed, install two stop screws (36) in collar (37), as shown.
Install locknuts (38) .
7/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 15 g00454275
17. Install bolt (41) in block (42), as shown. Install spring (40) on bolt (41), as shown. Put collar
(37) in position on bolt (41) with the hole in the collar in alignment with the notch in bolt
(41) and install bolt (39) in order to hold the collar in place.
Illustration 16 g00454428
Illustration 17 g00459548
8/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. 18. Put block (42) in position on housing (43). Align the holes in block (42) with the dowels.
Tighten two bolts (44) .
Illustration 18 g00590080
3304B torque control
19. Assemble the torque control on the 3304B engine. Install retainer (51), two bars (49), spacer
(50), contact (46), and insulator (45) in position on bolts (52) .
9/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Illustration 19 g00454429
20. Assemble the torque control on the 3306B, as follows:
a. Install spring (48), spacer (47), contact (46) and spacer (50) on insulator (45), as
shown.
b. Install retainer (51) and bar (49) on bolts (52) .
10/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 20 g00459552
21. Put torque control (53) in position on block (40). Install bolts (54) .
Illustration 21 g00454442
Note: When housing (43) is installed on the fuel injection pump housing, the flange on bolt
(38) must be behind the dashpot. If housing (43) is installed with the flange on bolt (38) on
the wrong side of the dashpot, the riser in the governor will be held in the maximum fuel
delivery position.
22. Install gasket (56) on the fuel injection pump housing. Put housing (43) in position on the
fuel injection pump housing with bolt (38) behind the dashpot, as shown. Install bolts (55)
that hold housing (43) in place.
11/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 22 g00459558
23. Use Tool (C) in order to install lip type seal (57) in the outer governor housing with the lip
inward.
24. Install adjustment screw (58) and the locknut for the high idle adjustment.
Illustration 23 g00459560
25. Install check valve (59) .
12/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. Illustration 24 g00459562
26. Put lever (60) in position, as shown. Install shaft (61) .
Illustration 25 g00459564
27. Put the gasket and shutoff solenoid (62) in position and install two bolts (63) .
28. Put the gasket and cover (64) in position and install two bolts (65) .
29. Install body (66) and contact (67) .
30. Put the O-ring seal on adapter (68) and put the coupling and adapter (68) in position. Install
two bolts (69) .
Illustration 26 g00459590
31. Install spring (70) in shaft assembly (71). Install pin (72) in shaft assembly (71). The tip of
pin (72) should be engaged in the hole in spring (70). Install pin (73) in shaft assembly (71)
in order to hold pin (72) in place.
13/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Illustration 27 g00459593
32. Put stop (76) and plates (74) in position on shaft assembly (71) and install pins (75). Install
snap rings (77) .
Illustration 28 g00459595
33. Put levers (79) and (78) in position in the housing, as shown. Install shaft assembly (71) .
Illustration 29 g00459596
14/17(W)w
2019/9/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...