This document provides instructions for removing and installing inlet and exhaust valve guides on a 213B excavator. The removal procedure involves using a valve guide driver tool to remove the guides from the cylinder head. For installation, the guides are tapped into position in the cylinder head and driven in using the driver tool along with a guide collar until fully seated. Proper cleaning and lubrication of parts is emphasized to prevent premature wear during reassembly.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8usejkdmmd8i
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process including inserting an extractor tool into the valve seat, expanding the tool to remove the seat, and installing a new seat by tapping it into place in the cylinder head. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...tengtui535
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...ze6074xunong
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...hdjsjndndnd
This document provides instructions for removing and installing inlet and exhaust valve seats in a Caterpillar 3116 engine. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Proper cleaning and lubrication of parts is emphasized to prevent premature wear and failure of components. Relevant guidelines for determining if removed parts can be reused are also referenced.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8seodkdmdmed3
This document provides instructions for installing an inlet manifold on a 214B FT excavator engine. It describes:
1) Cleaning and positioning a new gasket on the cylinder head and installing the air inlet manifold with bolts.
2) Installing air inlet elbows and connecting the air inlet heater solenoid.
3) Completing the installation by reattaching the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8usejkdmmd8i
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process including inserting an extractor tool into the valve seat, expanding the tool to remove the seat, and installing a new seat by tapping it into place in the cylinder head. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...tengtui535
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...ze6074xunong
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...hdjsjndndnd
This document provides instructions for removing and installing inlet and exhaust valve seats in a Caterpillar 3116 engine. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Proper cleaning and lubrication of parts is emphasized to prevent premature wear and failure of components. Relevant guidelines for determining if removed parts can be reused are also referenced.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8seodkdmdmed3
This document provides instructions for installing an inlet manifold on a 214B FT excavator engine. It describes:
1) Cleaning and positioning a new gasket on the cylinder head and installing the air inlet manifold with bolts.
2) Installing air inlet elbows and connecting the air inlet heater solenoid.
3) Completing the installation by reattaching the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for specifications on reusable components. The document is from a service repair manual for excavator and engine models.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts. The process includes removing any remaining valves first before pressing new guides into place and ensuring they are flush with the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety notices are provided to keep parts clean and contain fluids during repair work.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
1) The document provides disassembly and assembly instructions for the final drive of a 318C excavator.
2) It lists required tools and parts and gives step-by-step instructions to disassemble components like the cover, planetary assembly, ring gear, and carrier.
3) The assembly section instructs to clean all parts thoroughly and replace all seals before reinstalling components like the support ring, planetary gears, and retainer nut in the reverse order of disassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
More Related Content
Similar to Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for specifications on reusable components. The document is from a service repair manual for excavator and engine models.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts. The process includes removing any remaining valves first before pressing new guides into place and ensuring they are flush with the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety notices are provided to keep parts clean and contain fluids during repair work.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Similar to Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf (20)
1) The document provides disassembly and assembly instructions for the final drive of a 318C excavator.
2) It lists required tools and parts and gives step-by-step instructions to disassemble components like the cover, planetary assembly, ring gear, and carrier.
3) The assembly section instructs to clean all parts thoroughly and replace all seals before reinstalling components like the support ring, planetary gears, and retainer nut in the reverse order of disassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix MDY) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and housing. It then lists 7 notes and 28 steps to reassemble the final drive by installing components like seals, bearings, shims, and housing pieces in the reverse order of disassembly. The goal is to carefully disassemble and reassemble the final drive while cleaning parts and applying sealant or anti-seize compound where needed.
Caterpillar Cat 318D L Excavator (Prefix ZKJ) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists notes on cleanliness and provides 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
This document provides instructions for removing and installing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses, removing mounting bolts, and installing replacement parts in the reverse order of removal, taking safety precautions for hot components. Tools required include goggles, gloves, a respirator, and specialty tools for compressing valve springs.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix EZW) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a piston pump on a 257D Multi Terrain Loader. It lists required tools and outlines a step-by-step process including disconnecting hoses and harnesses, using lifting tools to support the pump, and removing bolts. The reassembly process is described in reverse order, noting steps like applying thread lock compound and centering the swashplate.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix R9M) Service Repair Manual Instan...ze6074xunong
This document provides instructions for removing and installing the engine on a Caterpillar 140M 2 motor grader. Key steps include draining fluids, disconnecting tubes, hoses and wiring harnesses, and removing mounting bolts. Special tools may be required to remove some components. The engine should be attached to a lifting device and removed, then the installation process follows the removal steps in reverse order. Safety precautions are provided regarding contained fluids, pressurized systems, and ensuring parts are kept clean to prevent damage.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...ze6074xunong
This document provides disassembly and assembly instructions for a piston motor (hydrostatic) on a Caterpillar 257B3 Multi Terrain Loader. It lists 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then lists 13 steps to assemble the piston motor by installing those same components in reverse order. The document includes illustrations and lists required tools for each step.
Caterpillar Cat 257 Multi Terrain Loader (Prefix CMM) Service Repair Manual I...ze6074xunong
This document provides instructions for removing and installing a flywheel housing on a 257 Multi Terrain Loader with a 3034 engine. It describes using link brackets and a lifting device to remove the flywheel housing by removing its bolts. For installation, it instructs cleaning the cylinder block face, placing the housing over dowels on the block, and reinstalling the bolts while using link brackets for support. Precautions are given to keep parts clean and not damage surfaces.
Caterpillar Cat 143H Motor Grader (Prefix APN) Service Repair Manual Instant ...ze6074xunong
The document provides instructions for disassembling and assembling the final drive of a 143H motor grader. It describes removing the final drive unit and then disassembling it by removing gears, shafts, bearings and seals. The assembly section describes installing these components in reverse order and adjusting shims to set proper end play. Precautions are given to clean parts thoroughly and use new parts if worn.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M Motor Grader (Prefix B9M) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for removing the drawbar from a 140M Motor Grader. It lists the required tools, gives safety warnings about hydraulic pressure, and outlines a 26-step procedure involving lowering the blade, removing bolts and pins, and using lifting equipment to remove the drawbar. Proper identification and plugging of hoses is noted to prevent fluid loss and contamination during the process.
The document provides instructions for removing and installing various engine components on a 299D XHP Compact Track Loader, including the water pump, water temperature regulator, flywheel, and crankshaft rear seal. The procedures describe draining coolant, removing guards and belts, and installing replacement parts in the reverse order of removal while taking safety precautions. Tools required include Three Bond 1217H adhesive and guide bolts for installing the flywheel.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual Instan...ze6074xunong
This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides 44 steps and illustrations to assemble the transmission components which include installing bearings, gears, seals, pistons, clutches, and housing components. Proper cleaning, heating/cooling of parts, and torque specifications are noted throughout the assembly process.
Caterpillar Cat 315B L Excavator (Prefix 5SW) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the travel motor of a 315B L excavator. The disassembly process involves removing 23 separate components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional details to ensure proper reinstallation of components, such as applying sealant and lubricant, and using strings to hold parts in place temporarily.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions with accompanying illustrations. Safety and installation notes are provided throughout.
This document provides instructions for disassembling and assembling the travel motor on a 315C Excavator. The disassembly process involves removing 27 individual parts in 28 steps, including removing bolts, seals, bearings, pistons, and other internal components. The assembly process reverses the disassembly steps and includes applying lubricant to parts and ensuring proper installation of springs, seals, and other components. Cleanliness is emphasized throughout to prevent contamination.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:20:07 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:21:03 UTC+0800 2021
5/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:21:58 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:22:54 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:23:50 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:24:46 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:25:41 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:26:37 UTC+0800 2021
3/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943853
Engine Oil Filter Bypass Valve - Remove and Install
SMCS - 1308-010-BV
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g00630032
Illustration 2 g00629985
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and the O-ring seal from the engine oil filter base.
2. Remove valve spring (2) and bypass valve (3) from the engine oil filter base.
Installation Procedure
NOTICE
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00630032
Illustration 4 g00629985
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil filter base.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. 3. Install plug (1) in the engine oil filter base.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:27:33 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01944039
Engine Oil Cooler Bypass Valve - Remove and Install
SMCS - 1314-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 1 g00629979
Illustration 2 g00629985
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and the O-ring seal from the engine oil cooler.
2. Remove valve spring (2) and bypass valve (3) from the engine oil cooler.
Installation Procedure
NOTICE
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00629985
Illustration 4 g00629979
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil cooler.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...