Caterpillar cat 160 h motor grader (prefix asd) service repair manual (asd00001 and up)

Service Repair Manual
Models
160H Motor Grader

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 160H MOTOR GRADER ASD
Configuration: 160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Machine Systems
Media Number -RENR4124-06 Publication Date -01/09/2007 Date Updated -24/09/2007
i05508896
Circle Drive - Disassemble
SMCS - 5207-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Forcing Bolt 3/8-16 by 4 inch 2
B 138-7575 Link Bracket 1
C 8H-0663 Bearing Puller Gp 1
D
8B-7554 Bearing Cup Puller Gp 1
8B-7548 Push-Puller Tool Gp 1
Start By:
a. Remove the circle drive. Refer to Disassembly and Assembly, "Circle Drive - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/9160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB...
2019/11/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00937730
1. Remove coupling (1) from housing (3). Remove pin (2) from coupling (1).
2. Remove nuts (4). Remove bracket (5).

3. Remove O-ring seal (7) and shims (8).
4. Remove bearing cup (6) from bracket (5).
5. Remove bolts (9) and cover (10).
6. Remove bolts (11).

7. Install Tooling (A) and remove cover (12).
8. Remove plug (13) and O-ring seal (14) from cover (12).
9. Remove bearing (15) from cover (12).

10. Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B).
The weight of shaft assembly (16) is approximately 32 kg (70 lb).
11. Remove shaft assembly (16). Remove Tooling (B).

12. Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20).
13. Remove spring (21) and spacer (22).

14. Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from
gear (23). Remove spacer (26).

15. Remove thrust washer (27) and remove bearing (28).
16. Remove worm assembly (29) from housing (3).
17. Use Tooling (C) and a suitable press in order to remove bearings (31) from worm assembly
(29).

18. Use Tooling (D) in order to remove bearing cup (32) from housing (3).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 28 11:22:20 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 160H MOTOR GRADER ASD
Configuration: 160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Machine Systems
Media Number -RENR4124-06 Publication Date -01/09/2007 Date Updated -24/09/2007
i07424503
Circle Drive - Assemble
SMCS - 5207-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 439-3940 Bracket As 1
E 8T-5096 Dial Indicator Gp 1
F - Loctite 243 -
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.

1. Lower the temperature of bearing cup (32). Install bearing cup (32) in housing (3). Lower
the temperature of bearing (28). Install bearing (28) to a depth of 2.00 ± 0.50 mm
(0.079 ± 0.020 inch) below the face.
2. Raise the temperature of bearing cones (31). Install bearing cones (31) on worm assembly
(29).

3. Install worm assembly (29) in housing (3).
4. Lower the temperature on bearing cup (6). Install bearing cup (6) in bracket (5).
5. Torque nut (4A) to 20 N·m (15 lb ft) and nut (4B) 40 N·m (30 lb ft). Then Torque nut (4A)
to 80 N·m (60 lb ft) and nut (4B) 80 N·m (60 lb ft). Rotate the worm 3 revolutions then
back off the nuts.
6. Torque nut (4A) to 20 N·m (15 lb ft) and nut (4B) 40 N·m (30 lb ft) then torque nut (4A) to
40 N·m (30 lb ft) rotate the worm 3 revolutions.
7. Torque nut (4A) to 40 N·m (30 lb ft) and nut (4B) 40 N·m (30 lb ft). Measure the average
gap between the housing and adapter at the locations being torqued. Subtract
0.145 ± 0.065 mm (0.006 ± 0.003 inch) to obtain the desire shim pack thickness.

8. Remove nuts (4) and bracket (5).

9. Install gear (23) on shaft assembly (16). Install spacer (26). Install friction discs (24) and
discs (25) in gear (23).

10. Install spacer (22), spring (21), and spacer (19).
11. Install Tooling (B) (not shown) and bolts (17). Attach a suitable lifting device to Tooling
(B). The weight of shaft assembly (16) is approximately 32 kg (70 lb).

12. Install thrust washer (27).
Note: If bolts (17) are M16 bolts, follow Step 13 through Step 19 for the correct shimming
procedure.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

13. Install shaft assembly (16). Remove Tooling (B). Tighten bolts (17) to 150 ± 20N·m
(111 ± 15 lb ft).
14. Wait 45 minutes, then remove bolts (17) and retainer (18) to add shims (20)
15. Determine the required number of shims (20) to obtain 2.30 ± 0.25 mm (0.10 ± 0.01 inch) of
deflection in spring (21). Use a depth micrometer to obtain the distance from the end of
shaft assembly (16) to the flat surface on spacer (19).
16. Subtract 2.30 ± 0.25 mm (0.10 ± 0.01 inch) from the dimension that was measured in Step
15. The calculated dimension is the thickness of shims (20).
17. Install shims (20), retainer (18), and bolts (17).
18. Tighten bolts (17) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
19. Tighten bolts (17) again to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
Note: If bolts (17) are 1/2-13 thd bolts, follow Step 20 through Step 26 for the correct
shimming procedure.
20. Install shaft assembly (16). Remove Tooling (B). Tighten bolts (17) to 130 ± 7 N·m
(96 ± 5 lb ft).
21. Wait 45 minutes, then remove bolts (17) and retainer (18) to add shims (20)
22. Determine the required number of shims (20) to obtain 2.30 ± 0.25 mm (0.10 ± 0.01 inch) of
deflection in spring (21). Use a depth micrometer to obtain the distance from the end of
shaft assembly (16) to the flat surface on spacer (19).
23. Subtract 2.30 ± 0.25 mm (0.10 ± 0.01 inch) from the dimension that was measured in Step
15. The calculated dimension is the thickness of shims (20).
24. Install shims (20), retainer (18), and bolts (17).
25. Tighten bolts (17) to a torque of 130 ± 7 N·m (96 ± 5 lb ft).
26. Tighten bolts (17) again to a torque of 130 ± 7 N·m (96 ± 5 lb ft).

27. Lower the temperature of bearing (15). Install bearing (15) even with the bottom face of
cover (12).
28. Install O-ring seal (14) on cover (12). Lubricate the O-ring seal with the lubricant that is
being sealed. Install plug (13).
29. Install cover (12).

30. Install five bolts (11). Apply Tooling (F) to new bolts (11A). Install new bolts (11A), as
shown.
31. Install cover (10) and bolts (9).
10/12160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(S...

Caterpillar cat 160 h motor grader (prefix asd) service repair manual (asd00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (12)

Similar to Caterpillar cat 160 h motor grader (prefix asd) service repair manual (asd00001 and up)

Similar to Caterpillar cat 160 h motor grader (prefix asd) service repair manual (asd00001 and up) (11)

More from fujsfkkskekmem

More from fujsfkkskekmem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 160 h motor grader (prefix asd) service repair manual (asd00001 and up)