The document provides instructions for disassembling and assembling the final drive of a 140H Motor Grader. It lists 24 steps for disassembly, removing components like the sun gear shaft, planetary carrier, gear assemblies, ring gear, drive shaft, and seals. It then lists 30 steps for assembly, installing these components in reverse order, noting specifics like torque specifications and tool requirements.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 126
Configuration: 140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i02186165
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Brackets 2
B 5P-4204 Wrench Assembly 1
Start By:
a. Remove the final drives. Refer to Disassembly and Assembly, "Final Drive - Remove"for
the correct procedure.
Illustration 1 g00621106
1/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Remove sun gear shaft (1) from housing (2).
2. Remove planetary carrier (3) from housing (2).
Illustration 2 g00621108
Illustration 3 g00621109
3. Remove locking bolts (5), the washers, and retainers (6) from planetary carrier (3).
4. Remove planetary shafts (4) to remove gear assemblies (7) from planetary carrier (3).
Note: Each gear assembly (7) consists of two washers (8), two roller assemblies (9), gear
(10) and planetary shaft (4).
Note: Mark the location of the components of the gear assemblies for assembly purposes.
2/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00621111
5. Remove retaining ring (11) and washer (12) from planetary carrier (3).
Illustration 5 g00621112
6. Remove locking bolts (13), the washers, and plates (14) to remove ring gear (15).
7. Remove ring gear (15) from the housing (2).
Illustration 6 g00621113
8. Remove locking bolt (18), the washer, and lock (16) which holds nut (17) to drive shaft
(19).
3/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: Notice that the lubrication holes (X) in sprockets (20) are in alignment. This will help
in assembly procedures.
9. Use Tooling (B) (not shown) to remove nut (17) from the drive shaft (19).
Illustration 7 g00621114
10. Remove two sprockets (20) from drive shaft (19).
Illustration 8 g00621116
11. Remove drive shaft (19) and two roller bearing cones from housing (2). One of the roller
bearing cones will be removed with drive shaft (19). The remaining roller bearing cone
must be removed from the other end of housing (2). This will be completed during Step 12.
4/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00621118
12. Remove roller bearing cone (21) from drive shaft (19).
Illustration 10 g00621119
13. Remove bolts (22), the hard washers, retainer (23), the shim pack (not shown), and 10 shims
(not shown) from housing (2).
Illustration 11 g00621120
14. Attach Tooling (A) to housing (25). Secure Tooling (A) to a suitable lifting device.
15. Remove thrust washer (24) from housing (25).
16. Remove the housing (26) from housing (25).
5/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00621123
17. Remove lip seal (27) from housing (25).
Note: Secure the pipe plug on housing (25) for assembly purposes.
Illustration 13 g00621125
18. Remove wear rings (28) from housing (26).
19. Remove thrust washer (29) from housing (26).
20. Remove lip seal (30) from housing (26).
6/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00621127
21. Remove roller bearing cup (30) from housing (26).
22. Remove lip seal (31) from housing (26).
Illustration 15 g00621128
23. Remove inner roller bearing cup (32) from housing (26).
24. Repeat Steps 1 through 23 to disassemble the remaining final drive.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 20 09:13:49 UTC+0800 2020
7/7140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 126
Configuration: 140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i05371526
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B 5P-4204 Wrench Assembly 1
C 6V-4876 Lubricant 1
D 8T-5096 Dial Indicator Gp 1
Note: Use a suitable press to install the cones on the drive shafts and the cups. If necessary, only preheat
the cones to 135 °C (275 °F) for no more than 1 hour. It is important to reseat the cone or the cup with a
suitable driver after the bearing and adjacent parts have reached a uniform temperature.
1/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01060675
Illustration 2 g01060676
1. Lower the temperature of bearing cup (32) and install bearing cup (32) in housing (29). Check for
full seating of the bearing cup with a Feeler Gauge.
Illustration 3 g01060678
2/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 2. Place housing (29) in a vertical position with the flange downward.
3. Install lip seal (31) in housing (29). The lip of the seal must face outward. Lubricate the lip seal (31)
with the lubricant which is being sealed.
4. Lower the temperature of bearing cup (30) and install bearing cup (30) in housing (29). Check for
full seating of the bearing cup with a Feeler Gauge.
Illustration 4 g02782189
5. Apply Tooling (C) onto thrust washer (28). Apply Tooling (C) onto surface (X) and surface (Y).
Install thrust washer (18).
Illustration 5 g02782206
6. Install lip seal (25) into housing (26).
Illustration 6 g02783199
3/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 7. Turn over housing (26). Install wear sleeves (27). The diagonal cuts that are in wear sleeves (27) are
separated by 90°. Apply Tooling (C) onto thrust washer (24). Install thrust washer (24).
Illustration 7 g02783245
8. Use Tooling (A) and a suitable lifting device to install housing (26). The weight of housing (26) is
approximately 54 kg (120 lb). Install shims (23A). Use a suitable soft hammer to drive the wear
sleeves into housing (26) until the sleeves are flush with the top of the bore surface. Do not install
the shims at this time.
Illustration 8 g02783255
9. Drill three equally spaced 8 mm (5/16 inch) holes in retainer (23) if necessary. The holes must be
centered on the existing bolt hole pattern and perpendicular to each surface.
10. Measure the thickness of retainer (23) at the three hole locations. Average the three measurements
and record the result as Dimension (A).
4/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 9 g02783265
11. Install retainer (23). Install three of bolts (22). Tighten bolts (22) to a torque of 50 ± 7 N·m
(37 ± 5 lb ft). Completely loosen bolts (22). Finger tighten bolts (22). Use Tooling (D) to measure
the gap between the top surface of retainer (23) and the final drive housing at the three 8 mm
(5/16 inch) hole locations. Record the measurement from each of the three locations as the nominal
gap or Dimension (B).
12. Calculate the shim pack thickness for the three measurement locations by subtracting Dimension (A)
from the Dimension (B) giving you Dimension (C). Remove bolts (22) and retainer (23).
Illustration 10 g02783317
13. Install various shims (23A) that is equal to Dimension (C) plus + 0.075 - 0.025 mm
(+ 0.003 - 0.001 inch). Install retainer (23). Install bolts (22). Tighten bolts (22) to a torque of
270 ± 40 N·m (199 ± 30 lb ft).
Illustration 11 g01060689
5/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 12 g01060690
14. Preheat and install bearing cone (21) on drive shaft (20). Check for full seating of the cone with a
Feeler Gauge. With the drive shaft in a vertical position, set the housing on bearing cone (21).
15. Start bearing cone (33) (not shown) on the top of drive shaft (20). Do not preheat this bearing cone.
The bearing cone can be seated in position by using the sprocket during Step 17. Make sure that the
bearing cone is seated in the cup.
16. Install drive shaft (20) in housing assembly (2).
Illustration 13 g01060692
Illustration 14 g01060693
17. Place the first sprocket (19) on drive shaft (20). The large diameter must face downward.
18. Place the second sprocket (19) on drive shaft (20). The hub must face downward and the large
diameter must face upward. Ensure that the lubrication holes (X) for the spline are aligned.
6/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 19. Install nut (17) to the drive shaft (20). Rotate drive shaft (20) and hit the hub of sprockets (19) while
nut (17) is being tightened to a torque of 11 ± 1 N·m (100 ± 10 lb in) above seal drag.
20. Loosen nut (17) by one locking position. Hit the hub of sprockets (19) again.
21. The final torque that is needed to rotate shaft (20) should be 2 ± 1 N·m (20 ± 10 lb in) or
3.95 ± 1.13 N·m (35 ± 10 lb in)above the seal drag depending on machine model.
Table 2
Model Rolling Torque
120H, 120K, 135H 2.95 ± 1.13 N·m (26 ± 10 lb in)
12H, 12K, 140H, 140K, 143H, 160H, 160K, 163H 3.95 ± 1.13 N·m (35 ± 10 lb in)
Note: Refer to Testing and Adjusting, "Final Drive Bearings - Adjust" for bearing adjustments when
the final drive is in chassis.
22. Install bolt (18), the washer, and lock (16) which holds nut (17) to the drive shaft (20). Tighten bolt
(18) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
Illustration 15 g00621112
23. Position ring gear (15) to housing assembly (2).
24. Install bolts (13), the washers, and plates (14) to hold ring gear (15) to housing assembly (2). Tighten
locking bolts (13) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
Illustration 16 g00621111
25. Install washer (12) and retaining ring (11) in planetary carrier (3).
7/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 17 g00621108
Illustration 18 g00621109
26. Install gear assemblies (7) and planetary shafts (4) in planetary carrier (3).
Note: Each gear assembly (7) consists of two washers (8), two roller assemblies (9), planetary gear
(10), and planetary shaft (4).
27. Install retainers (6), the washers, and locking bolts (5) to planetary carrier (3) to hold planetary shafts
(4) and gear assemblies (7) in planetary carrier (3). Tighten locking bolts (5) to a torque of
50 ± 10 N·m (37 ± 7 lb ft).
Illustration 19 g00621106
28. Install planetary carrier (3) in housing assembly (2).
29. Install sun gear shaft (1) in housing assembly (2).
8/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 30. Repeat Steps 21 through 29 to assemble the remaining final drive.
End By:
a. Install the final drives.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 20 09:14:45 UTC+0800 2020
9/9140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 126
Configuration: 140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i01920768
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/2140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 1 g00999500
1. Attach a suitable lifting device to final drive (1). The weight of final drive (1) is
approximately 272 kg (600 lb).
2. Use pry bars (3) in order to balance final drive (1). Install final drive (1). Install nuts (2).
Tighten nuts (2) to a torque of 430 ± 60 N·m (317 ± 44 lb ft).
3. Fill the power train oil system. The capacity of the power train system is 47 L (12 US gal).
End By:
a. Install the tandem housing. Refer to Disassembly and Assembly, "Tandem Housing -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 20 09:15:40 UTC+0800 2020
2/2140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 126
Configuration: 140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i01924681
Transmission Oil Filter Base - Remove
SMCS - 3068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ
6V-9511 Face Seal Plug 1
6V-9512 Face Seal Plug 1
6V-9832 Cap As 1
6V-9833 Cap As 1
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g01001711
1. Disconnect harness assembly (1).
2. Disconnect hose (2) from the rear chassis support. Disconnect hose assemblies (3).
3. Remove bolts (4). Remove filter (5) and the base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 20 09:16:36 UTC+0800 2020
2/2140H Motor Grader 12600001-UP (MACHINE) POWERED BY 3176C Engine(SEBP...
2020/2/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...