The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Case ih stx450 steiger tractor service repair manual pin jee0102001 and afteruujjfjkkkdmme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Case ih stx440 tractor service repair manualuujjfjkkkdmme
This document provides safety warnings and instructions for removing and installing an engine. It contains 51 steps to remove the engine, which include disconnecting batteries, draining coolant, removing hoses, wires, and other components. It then lists 40 steps to reinstall the engine, reversing the removal process and reconnecting all components. The purpose is to provide a detailed procedure for safely removing and installing an engine.
Case ih stx375 steiger tractor service repair manual pin jee0102001 and afterfujsekfkksemm
This document provides instructions for removing the engine from STX Steiger tractors. It is the first book in a 12-book service manual. The removal process involves 21 steps, including draining fluids, disconnecting wiring harnesses, removing hoses and tubes, and detaching mounting hardware. The radiator, air cleaner, exhaust system, air conditioning components, fuel lines, and wiring must all be disconnected before an overhead hoist can be used to lift the engine out of the tractor.
New holland l225 tier 4 skid steer loader service repair manual [ndm461085 ]ujfjjkskkemmd
This service manual provides instructions for servicing the engine and other components of 200 Series Skid Steer Loaders and Compact Track Loaders, including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and fans, and then fully removing the engine from the machine. Specific models and applicable component sections are listed at the beginning. Safety warnings are provided throughout regarding personal safety and handling fluids and heavy components.
New holland cx5090 hillside combine harvesters service repair manualujfjjkskkemmd
This document is a service manual for CNH Industrial combine harvesters and provides technical information on the machines' systems and components. It contains over 55 chapters organized into sections covering the engine, transmission, axles, hydraulics, brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, and unloading systems. Each chapter provides technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical and hydraulic components.
New holland cx840 combine harvesters service repair manualujfjjkskkemmd
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland cx6.90 laterale fpt cursor 9 tier 4 b (final) combine harvester s...ujfjjkskkemmd
This service manual provides technical information for maintenance and repair of several combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains sections covering the engine, transmission, axles, hydraulic and electrical systems, attachments/headers, and other major components. Technical data, functional descriptions, diagnostics, and service procedures are provided for each system.
New holland c232 tier 4 compact track loader service repair manual [ndm451672...ujfjjkskkemmd
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
Case ih stx450 steiger tractor service repair manual pin jee0102001 and afteruujjfjkkkdmme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Case ih stx440 tractor service repair manualuujjfjkkkdmme
This document provides safety warnings and instructions for removing and installing an engine. It contains 51 steps to remove the engine, which include disconnecting batteries, draining coolant, removing hoses, wires, and other components. It then lists 40 steps to reinstall the engine, reversing the removal process and reconnecting all components. The purpose is to provide a detailed procedure for safely removing and installing an engine.
Case ih stx375 steiger tractor service repair manual pin jee0102001 and afterfujsekfkksemm
This document provides instructions for removing the engine from STX Steiger tractors. It is the first book in a 12-book service manual. The removal process involves 21 steps, including draining fluids, disconnecting wiring harnesses, removing hoses and tubes, and detaching mounting hardware. The radiator, air cleaner, exhaust system, air conditioning components, fuel lines, and wiring must all be disconnected before an overhead hoist can be used to lift the engine out of the tractor.
New holland l225 tier 4 skid steer loader service repair manual [ndm461085 ]ujfjjkskkemmd
This service manual provides instructions for servicing the engine and other components of 200 Series Skid Steer Loaders and Compact Track Loaders, including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and fans, and then fully removing the engine from the machine. Specific models and applicable component sections are listed at the beginning. Safety warnings are provided throughout regarding personal safety and handling fluids and heavy components.
New holland cx5090 hillside combine harvesters service repair manualujfjjkskkemmd
This document is a service manual for CNH Industrial combine harvesters and provides technical information on the machines' systems and components. It contains over 55 chapters organized into sections covering the engine, transmission, axles, hydraulics, brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, and unloading systems. Each chapter provides technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical and hydraulic components.
New holland cx840 combine harvesters service repair manualujfjjkskkemmd
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland cx6.90 laterale fpt cursor 9 tier 4 b (final) combine harvester s...ujfjjkskkemmd
This service manual provides technical information for maintenance and repair of several combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains sections covering the engine, transmission, axles, hydraulic and electrical systems, attachments/headers, and other major components. Technical data, functional descriptions, diagnostics, and service procedures are provided for each system.
New holland c232 tier 4 compact track loader service repair manual [ndm451672...ujfjjkskkemmd
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland br6080 round balers service repair manualujfjjkskkemmd
This service manual provides instructions for repairing and maintaining a baler. It includes sections covering the baler's hydraulic, electrical, electronic and pneumatic systems, power systems, transmission, axles, brakes, wheels, and crop processing functions. Safety information is also included, emphasizing the importance of following proper safety procedures when servicing equipment.
New holland b100 c stage iv tractor loader backhoe service repair manualujfjjkskkemmd
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all systems of the machines from the engine and transmission to hydraulics, electrical systems, and safety information. The manual provides repair and maintenance instructions for qualified service personnel and is intended to ensure safe and proper operation of the equipment.
New holland b95 tc backhoe loader service repair manualujfjjkskkemmd
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h018...ujfjjkskkemmd
This document provides instructions for servicing a 951B track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and more. It also provides details on specific service tools, pressing parts, bolts and torque, bearing types, seals, and other components. The goal is to ensure proper procedures are followed for repairing and reassembling the machine.
Caterpillar cat 951 b track loader (prefix 86j) service repair manual (86j000...ujfjjkskkemmd
This document provides instructions for disassembling and assembling starting motors for a 951B track loader. It describes the parts and tools needed and steps to:
1. Disassemble a 42-MT starting motor by removing housing bolts, brushes, field windings, and pinion drive.
2. Inspect and clean all parts.
3. Assemble the starting motor by reversing the disassembly steps, applying grease or thread lock as needed.
Caterpillar cat 931 b track loader (prefix 30y) service repair manual (30y000...ujfjjkskkemmd
This service repair manual provides instructions for removing and installing various components of a Caterpillar 931B track loader, including:
1) Track roller frames, which are removed by taking off guards, yokes, and bolts, and lifted with straps and a hoist.
2) Pivot shafts, by removing seals, bearings, and support assemblies after draining oil and using straps and hoists.
3) Equalizer bars, which are removed by taking off guards and pins after jacking up the machine.
Caterpillar cat 931 b track loader (prefix 26y) service repair manual (26y000...ujfjjkskkemmd
This document provides instructions for removing and installing steering clutches on a 931B track loader. It begins by listing the necessary preparatory steps of removing the hydraulic tank, fuel tank, battery, brake linkage, and disconnecting hoses and wiring. It then details removing each individual component of the steering clutch assembly, including the cylinder, plates, springs, housing, and linkages. The instructions conclude by describing how to reinstall each part in reverse order and providing final checks and replacements of the tanks.
Caterpillar cat 931 b track loader (prefix 4sc) service repair manual (4sc000...ujfjjkskkemmd
This document provides instructions for removing and installing track carrier rollers, track roller guards, and track rollers on a Caterpillar 931B track loader. It describes loosening the track, removing covers and guards, and then removing rollers by taking off bolts and locks. Reinstallation involves cleaning surfaces, applying lubricant, pressing in bearings, and installing seals before reattaching components using bolts. Precautions are given regarding hydraulic pressure in the track and ensuring paint is removed from contact surfaces.
Caterpillar cat 432 d backhoe loader (prefix bld) service repair manual (bld0...ujfjjkskkemmd
This document provides instructions for disassembling the transmission of a 432D Backhoe Loader. It lists the required tools and begins by having the transmission removed per the specified procedure. The transmission is then disassembled into its major components which are further disassembled. Steps include removing the front and rear drive shafts, piston pump, draining the oil, and separating the case from the transmission using bolts and lifting devices. The front output shaft and various internal components like bearings, gears, and seals are then removed from the transmission.
Caterpillar cat 432 d backhoe loader (prefix bld) service repair manual (bld0...ujfjjkskkemmd
This document provides instructions for removing and installing exhaust manifolds and air inlet manifolds on Caterpillar 3054 engines. It includes detailed removal and installation procedures with illustrations. The procedures describe removing components like nuts, bolts, manifolds, and gaskets, and installing new gaskets, manifolds, and related components. Special notices are provided regarding keeping parts clean and containing fluids.
Caterpillar cat 430 e backhoe loader (prefix swc) service repair manual (swc0...ujfjjkskkemmd
This document provides instructions for disassembling and assembling the transmission of a 430E backhoe loader. It lists required tools and outlines 43 steps to disassemble parts like the transmission case, direct drive shaft, and input shaft. It also outlines 13 steps to assemble parts back into the transmission case like installing O-rings, seals, bearings, and valves. The summary aims to concisely convey the high-level goal of providing transmission disassembly and assembly instructions in under 3 sentences.
Caterpillar cat 428 e backhoe loader (prefix snl) service repair manual (snl0...ujfjjkskkemmd
The document provides instructions for removing a hydraulic tank from a 428E backhoe loader. It involves draining the hydraulic oil, removing various panels and covers, disconnecting hoses and harness assemblies, and removing bolts to detach the tank. Twenty-six steps are outlined detailing how to remove the floor plates, side panels, ducting, and other components to access and detach the hydraulic tank.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...ujfjjkskkemmd
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...ujfjjkskkemmd
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new gaskets and seals. Safety notices are included to warn technicians to contain fluids and wear protective equipment when working on the engine.
Caterpillar cat 322 c l 322cl excavator (prefix fed) service repair manual (f...ujfjjkskkemmd
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators powered by a 3126 engine. The summary is:
1. The pilot valve must first be removed from the machine by disconnecting hoses, wires, switches, and removing mounting bolts.
2. To disassemble the pilot valve, over 30 individual parts must be removed including fittings, seals, covers, springs, bushings, and spools.
3. Cleanliness is important during disassembly to prevent contamination, and identification marks should be made on parts.
Caterpillar cat 322 c l 322cl excavator (prefix daa) service repair manual (d...ujfjjkskkemmd
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It consists of 20 steps for disassembly and 23 steps for assembly. Key parts of the pilot valve that are disassembled include the spool assembly, springs, seals, plugs and various plates. Cleanliness is emphasized throughout the process. The assembly section provides detailed instructions on installing replacement parts and adjusting components to the proper dimensions.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...ujfjjkskkemmd
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
New holland br6080 round balers service repair manualujfjjkskkemmd
This service manual provides instructions for repairing and maintaining a baler. It includes sections covering the baler's hydraulic, electrical, electronic and pneumatic systems, power systems, transmission, axles, brakes, wheels, and crop processing functions. Safety information is also included, emphasizing the importance of following proper safety procedures when servicing equipment.
New holland b100 c stage iv tractor loader backhoe service repair manualujfjjkskkemmd
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all systems of the machines from the engine and transmission to hydraulics, electrical systems, and safety information. The manual provides repair and maintenance instructions for qualified service personnel and is intended to ensure safe and proper operation of the equipment.
New holland b95 tc backhoe loader service repair manualujfjjkskkemmd
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h018...ujfjjkskkemmd
This document provides instructions for servicing a 951B track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and more. It also provides details on specific service tools, pressing parts, bolts and torque, bearing types, seals, and other components. The goal is to ensure proper procedures are followed for repairing and reassembling the machine.
Caterpillar cat 951 b track loader (prefix 86j) service repair manual (86j000...ujfjjkskkemmd
This document provides instructions for disassembling and assembling starting motors for a 951B track loader. It describes the parts and tools needed and steps to:
1. Disassemble a 42-MT starting motor by removing housing bolts, brushes, field windings, and pinion drive.
2. Inspect and clean all parts.
3. Assemble the starting motor by reversing the disassembly steps, applying grease or thread lock as needed.
Caterpillar cat 931 b track loader (prefix 30y) service repair manual (30y000...ujfjjkskkemmd
This service repair manual provides instructions for removing and installing various components of a Caterpillar 931B track loader, including:
1) Track roller frames, which are removed by taking off guards, yokes, and bolts, and lifted with straps and a hoist.
2) Pivot shafts, by removing seals, bearings, and support assemblies after draining oil and using straps and hoists.
3) Equalizer bars, which are removed by taking off guards and pins after jacking up the machine.
Caterpillar cat 931 b track loader (prefix 26y) service repair manual (26y000...ujfjjkskkemmd
This document provides instructions for removing and installing steering clutches on a 931B track loader. It begins by listing the necessary preparatory steps of removing the hydraulic tank, fuel tank, battery, brake linkage, and disconnecting hoses and wiring. It then details removing each individual component of the steering clutch assembly, including the cylinder, plates, springs, housing, and linkages. The instructions conclude by describing how to reinstall each part in reverse order and providing final checks and replacements of the tanks.
Caterpillar cat 931 b track loader (prefix 4sc) service repair manual (4sc000...ujfjjkskkemmd
This document provides instructions for removing and installing track carrier rollers, track roller guards, and track rollers on a Caterpillar 931B track loader. It describes loosening the track, removing covers and guards, and then removing rollers by taking off bolts and locks. Reinstallation involves cleaning surfaces, applying lubricant, pressing in bearings, and installing seals before reattaching components using bolts. Precautions are given regarding hydraulic pressure in the track and ensuring paint is removed from contact surfaces.
Caterpillar cat 432 d backhoe loader (prefix bld) service repair manual (bld0...ujfjjkskkemmd
This document provides instructions for disassembling the transmission of a 432D Backhoe Loader. It lists the required tools and begins by having the transmission removed per the specified procedure. The transmission is then disassembled into its major components which are further disassembled. Steps include removing the front and rear drive shafts, piston pump, draining the oil, and separating the case from the transmission using bolts and lifting devices. The front output shaft and various internal components like bearings, gears, and seals are then removed from the transmission.
Caterpillar cat 432 d backhoe loader (prefix bld) service repair manual (bld0...ujfjjkskkemmd
This document provides instructions for removing and installing exhaust manifolds and air inlet manifolds on Caterpillar 3054 engines. It includes detailed removal and installation procedures with illustrations. The procedures describe removing components like nuts, bolts, manifolds, and gaskets, and installing new gaskets, manifolds, and related components. Special notices are provided regarding keeping parts clean and containing fluids.
Caterpillar cat 430 e backhoe loader (prefix swc) service repair manual (swc0...ujfjjkskkemmd
This document provides instructions for disassembling and assembling the transmission of a 430E backhoe loader. It lists required tools and outlines 43 steps to disassemble parts like the transmission case, direct drive shaft, and input shaft. It also outlines 13 steps to assemble parts back into the transmission case like installing O-rings, seals, bearings, and valves. The summary aims to concisely convey the high-level goal of providing transmission disassembly and assembly instructions in under 3 sentences.
Caterpillar cat 428 e backhoe loader (prefix snl) service repair manual (snl0...ujfjjkskkemmd
The document provides instructions for removing a hydraulic tank from a 428E backhoe loader. It involves draining the hydraulic oil, removing various panels and covers, disconnecting hoses and harness assemblies, and removing bolts to detach the tank. Twenty-six steps are outlined detailing how to remove the floor plates, side panels, ducting, and other components to access and detach the hydraulic tank.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...ujfjjkskkemmd
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 428 d backhoe loader (prefix dsx) service repair manual (dsx0...ujfjjkskkemmd
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new gaskets and seals. Safety notices are included to warn technicians to contain fluids and wear protective equipment when working on the engine.
Caterpillar cat 322 c l 322cl excavator (prefix fed) service repair manual (f...ujfjjkskkemmd
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators powered by a 3126 engine. The summary is:
1. The pilot valve must first be removed from the machine by disconnecting hoses, wires, switches, and removing mounting bolts.
2. To disassemble the pilot valve, over 30 individual parts must be removed including fittings, seals, covers, springs, bushings, and spools.
3. Cleanliness is important during disassembly to prevent contamination, and identification marks should be made on parts.
Caterpillar cat 322 c l 322cl excavator (prefix daa) service repair manual (d...ujfjjkskkemmd
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It consists of 20 steps for disassembly and 23 steps for assembly. Key parts of the pilot valve that are disassembled include the spool assembly, springs, seals, plugs and various plates. Cleanliness is emphasized throughout the process. The assembly section provides detailed instructions on installing replacement parts and adjusting components to the proper dimensions.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...ujfjjkskkemmd
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Case ih stx375 steiger tractor service repair manual pin jee0102001 and after
1. STX275, STX325, STX375, STX425,
STX450 Steiger Tractors
P.I.N. JEE0102001 and After
Service Manual
Book 1 of 12
General
Engine
Rac 6-14470
2. Service Manual Number 6-14440
Book 1 - Publication 6-14470
General
Engine
Book 2- Publication 6-14480
Electrical
Book 3- Publication 6-14490
Steering
Book 4- Publication 6-14500
Power Train
Books 5- Publication 6-14510
Power Train (Continued)
Book 6- Publication 6-14520
Power Train (Continued)
Brakes
Book 7- Publication 6-14530
Hydraulics
Book 8 - Publication 6-14540
Chassis
Book 9 - Publication 6-14550
Chassis (Continued)
Book 10 - Publication 6-14560
Controller Systems
Book 11 - Publication 6-14570
Controller Systems (Continued)
Book 12- Publication 6-14580
Controller Systems (Continued)
You can order Service Manual Books separately (see publication
numbers above) or you can order a complete STX Steiger Service
Manual for P.I.N. JEE0102001 and After (Publication Number 6-14440).
4. 1001-2
Rac 7-90470 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
SAFETY
WARNING: THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT
SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS
SYMBOL, CAREFULLY READ THE MESSAGE THAT FOLLOWS AND
BE ALERT TO THE POSSIBILITY OF PERSONAL INJURY OR
DEATH.** M171B
!
To prevent injury always follow the Warning, Caution
and Danger notes in this section and throughout the
manual.
Put the “Do Not Operate” tag shown below on the key
for the key switch when keys are removed for
servicing or repairing the machine. Tags are available
from your service parts supplier.
Before servicing a machine, park the machine on
hard level ground. Turn off the engine, apply the
parking brake and remove the key from the key
switch. Put blocks in front of and behind either the
front or rear wheels.
MS99B001
WARNING: Read the operators manual to
familiarize yourself with the correct control
functions. M489
WARNING: Operate the machine and
equipment controls from the seat position
only. Any other method could result in
serious injury. M490
WARNING: This is one man machine, no
riders allowed. M491
!
!
!
WARNING: Before starting engine study
Operators Manual safety messages. Read
all safety signs on machine. Clear the area of
other persons. Learn and practice safe use
of controls before operating. It is your
responsibility to understand and follow
manufacturers instructions on machine
operation, service, and to observe pertinent
laws and regulations. Operator and Service
Manuals may be obtained from your
equipment dealer. M103A
WARNING: If you wear clothing that is too
loose or do not use the correct safety
equipment for your job, you can be injured.
Always wear clothing that will not catch on
objects. Extra safety equipment that can be
required includes hard hat, safety shoes, ear
protection, eye or face protection, heavy
gloves and reflector clothing. M492
WARNING: When working in the area of the
fan belt with the engine running, avoid loose
clothing if possible, and use extreme caution.
M493
WARNING: When doing checks and tests
on the equipment hydraulics, follow the
procedures as they are written. DO NOT
change the procedure. M494
WARNING: When putting the hydraulic
cylinders on this machine through the
necessary cycles to check operation or to
remove air from a circuit, make sure all
people are out of the way. M495
WARNING: Always wear heat protective
gloves to prevent burning your hands when
handling heated parts. SM121A
!
!
!
!
!
!
5. 1001-3
Rac 7-90470 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ROLL OVER PROTECTIVE
STRUCTURE (ROPS)
ROPS, the operators seat, the seat belts and all
mounting, accessories and wiring inside the
operators protective system must be carefully
checked after a tractor accident and all parts with
damage must be replaced immediately. DO NOT
TRY TO MAKE REPAIRS OR WELD THE ROPS.
Safety Rules:
1. Do not make modifications to the ROPS.
Example, welding an accessory to the ROPS or
drilling a hole in the ROPS.
2. Special fasteners are used to install the operator
protective parts. Replacement parts must be the
same as given in the Parts Catalog.
WARNING: Lower all attachments to the
ground or use stands to safely support the
attachments before you do any maintenance
or service. M496
WARNING: Hydraulic oil or diesel fuel
leaking under pressure can penetrate the
skin and cause infection or other injury.
To Prevent Personal Injury:
Relieve all pressure, before disconnecting
fluid lines. Before applying pressure, make
sure all connections are tight and
components are in good condition.
Never use your hand to check for suspected
leaks under pressure.
Use a piece of cardboard or wood for this
purpose. If injured by leaking fluid, see your
doctor immediately. SM171A
WARNING: When removing hardened pins
such as a pivot pin, or a hardened shaft, use
a soft head (brass or bronze) hammer or use
a driver made from brass or bronze and a
steel head hammer. M497
WARNING: When using a hammer to
remove and install pivot pins or separate
parts using compressed air or using a
grinder, wear eye protection that completely
encloses the eyes (approved goggles or
other approved eye protectors). M498
WARNING: Use suitable floor (service)
jacks or chain hoist to raise wheels or tracks
off the floor. Always block machine in place
with suitable safety stands M499
WARNING: When servicing or repairing the
machine. Keep the shop floor and operators
compartment and steps free of oil, water,
grease, tools, etc. Use an oil absorbing
material and or shop cloths as required. Use
safe practices at all times. M500
WARNING: Some components of this
machine are very heavy. Use suitable lifting
equipment or additional help as instructed in
the Service Manual. M501
!
!
!
!
!
!
!
WARNING: Engine exhaust fumes can
cause death. If it is necessary to start the
engine in a closed place, remove the exhaust
fumes from the area with an exhaust pipe
extension. Open the door and get outside air
into the area. M502
WARNING: When the battery electrolyte is
frozen, the battery can explode if (1), you try
to charge the battery, or (2), you try to jump
start and run the engine. To prevent the
battery electrolyte from freezing, try to keep
the battery at full charge. If you do not follow
these instructions, you or others in the area
can be injured. M503
WARNING: Batteries contain acid and
explosive gas. Explosions can result from
sparks, flames or wrong cable connections.
To connect the jumper cables correctly to the
battery of this machine see the Operators
Manual. Failure to follow these instructions
can cause serious injury or death. M504
!
!
!
7. 2001-3
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ENGINE REMOVAL
STEP 1
MK98C099
1. Park the tractor on solid, level surface.
2. Place the shift lever in PARK.
3. Shut off the engine and remove the key from the
switch.
STEP 2
MK99J135
See Section 9001 A/C System - Recovery,
Evacuation, Charging for instructions to discharge
the air conditioning system.
STEP 3
MK99K032
Open the battery access door and disconnect the
negative battery cables from the two batteries.
STEP 4
MK99H256
See Section 9007 Hood Removal for instructions to
remove the hood and support bar from the tractor.
8. 2001-4
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 5
MK99J073
See Section 9008 Radiator Removal for instructions
to drain the coolant and remove the radiator and
cooler assembly from the front frame.
STEP 6
MK99J008
Remove the wire connector from the air restrictor
switch on the air cleaner outlet tube.
STEP 7
MK99J007
Loosen the clamps on the air cleaner outlet tube and
remove the tube.
STEP 8
MK99J049
Loosen the clamp and remove the exhaust aspirator
hose from the air cleaner inlet.
STEP 9
MK99J051
Remove the aspirator tube P-clamp mounting bolt.
9. 2001-5
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 10
MK99J050
Loosen the clamp and remove the aspirator tube and
hose from the muffler.
STEP 11
MK99J004
Attach an overhead hoist to the hood support
assembly and remove the two right side mounting
bolts.
STEP 12
MK99J024
Remove the two left side hood support mounting
bolts.
STEP 13
MK99J010
Remove the rear hood support mounting assembly
and remove the assembly from the tractor.
STEP 14
MK99J023
Remove the wire connector from the A/C system high
pressure switch.
STEP 15
MK99J020
Remove the suction and discharge hoses from the
A/C compressor. Install caps on the compressor
fittings and plugs in the hoses. Discard the O-rings.
10. 2001-6
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 16
MK99J018
Remove the mounting bolt and nut. Remove the A/C
suction and dryer hoses from the hose bracket.
STEP 17
MK98G023
Turn the valve lever clockwise to shut off the fuel
valve on the tank.
STEP 18
MK99J017
Install clamps on the fuel supply and return hoses.
Loosen the hose clamps and remove the hoses from
the engine. Cap the fuel pump fittings and plug the
hose ends.
STEP 19
MK99J028
Remove the engine front frame wire harness
connector from the engine wire harness.
STEP 20
MK99J022
Open the cover plug (1) and remove the Phillips head
screw to remove the starter switch wire (2) from the
starter solenoid.
STEP 21
MK99J021
Remove the battery cable, alternator cable and
starter switch power supply wire from the starter
solenoid.
1
2
11. 2001-7
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 22
MK99J025
Remove the battery cable clamp mounting bolt.
STEP 23
MK99J027
Remove the alternator to battery cable from the
alternator.
STEP 24
MK99J026
Remove the alternator exciter wire.
STEP 25
MK99J034
Remove the alternator wire harness from the engine
clamp.
STEP 26
MK99J016
Remove the ground strap from the engine.
STEP 27
MK99J177
Mark the hoses for location. Loosen the hose clamps
and remove the heater hoses from the engine.
12. 2001-8
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 28
MK99J031
Loosen the hose clamp and remove the lower
radiator hose from the engine.
STEP 29
MK99J035
Loosen the band clamps on the exhaust flex tube.
STEP 30
MK99J029
Remove the channel clamp (1) from the turbo
exhaust port. Remove the exhaust pipe (2) and flex
tube from between the turbo and the frame mounted
exhaust pipe.
STEP 31
MK99J033
Remove the four mounting bolts and slide the drive
shaft rearward away from the engine drive coupler.
STEP 32
MK99J041
Install the OEM 4130 Load Rotor on the two engine
lifting brackets. Attach the load rotor to an overhead
hoist.
IMPORTANT: The engine lifting brackets are for
vertical lifting only. Any lifting device that is not
vertically in-line with the lifting brackets can damage
the engine rocker arm cover or cause bracket failure.
1
2
13. 2001-9
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 33
MK99J013
Remove the lock nut, bolt and washers from the front
engine mount.
STEP 34
MK99J030
Remove the lock nut, large flat washer, bolt and small
flat washer from the left side (shown) and right side
rear engine mounts.
STEP 35
MK99J040
To remove the engine, lift the engine until the oil pan
will clear the front frame engine mount crossmember.
Move the engine forward out of the tractor.
14. 2001-10
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ENGINE INSTALLATION
STEP 36
MK99J036
Install the OEM 4130 Load Rotor on the two engine
lifting brackets. Attach the load rotor to an overhead
hoist.
IMPORTANT: The engine lifting brackets are for
vertical lifting only. Any lifting device that is not
vertically in-line with the lifting brackets can damage
the engine rocker arm cover or cause bracket failure.
STEP 37
MK99J037
If removed after the engine was removed, install the
three large flat washers on the front and rear (shown)
rubber isolators.
STEP 38
MK99J039
Install the bolts and small flat washers in the rear
engine mounts. Lift the engine until the oil pan will
clear the front frame and engine mount
crossmember. Move the engine rearward into the
tractor until it is positioned above the engine
mounting brackets.
STEP 39
MK99J038
Use the rear mounting bolts as guides and slowly
lower the engine on the front frame engine mounting
brackets.
15. 2001-11
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 40
MK99J013
Install the bolt, flat washers and lock nut through the
front motor mount. Tighten the bolt and lock nut to
specifications.
STEP 41
MK99J030
Install the large flat washers and lock nuts on the rear
engine mount bolts. Tighten the bolts and lock nuts to
specifications. Remove the hoist and load rotor.
STEP 42
MK99J015
Move the driveshaft forward and install the four M12 x
20 bolts to secure the driveshaft to the engine drive
coupler. Tighten the bolt and lock nut to
specifications.
STEP 43
MK99J031
Install the lower radiator hose on the engine and
tighten the hose clamp.
STEP 44
MK99J016
Install the right side ground strap on the engine.
16. 2001-12
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 45
MK99J177
Install the heater supply hose (1) and return hose (2)
on the engine and tighten the hose clamps.
STEP 46
MK99J025
Use the M8 x 20 bolt and flat washer to install the
heater hose and battery cable bracket on the right
side motor mount. Tighten the bolt to specifications.
STEP 47
MK99J021
Install the battery cable, starter switch power supply
wire and alternator cable on the starter solenoid.
STEP 48
MK99J022
Install the starter switch wire on the starter solenoid.
STEP 49
MK99J026
Install the exciter wire on the alternator.
STEP 50
MK99J027
Install the battery wire on the alternator.
1
2
17. 2001-13
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 51
MK99J034
Install the alternator wire harness in the harness
clamp on the engine.
STEP 52
MK99J035
Install the flex tube and exhaust pipe assembly on
the frame mounted exhaust pipe. Do not tighten the
band clamp.
STEP 53
MK99J029
Use the channel clamp to install the exhaust pipe on
turbo exhaust outlet. Tighten the channel clamp to
specifications.
STEP 54
MK99J035
Tighten the flex tube band clamp to specifications.
STEP 55
MK99J028
Install the front frame wire harness connector on the
engine wire harness.
STEP 56
MK99J176
Install the fuel supply hose (1) and the fuel return
hose (2) on the fuel pump. Tighten the hose clamps
and remove the clamps from the hoses.
2
1
18. 2001-14
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 57
MK98G023
Turn the valve lever counterclockwise to open the fuel
shut-off valve on the tank.
STEP 58
MK99J018
Use the M8 x 20 bolt, washer and nut to install the
A/C suction and dryer hoses on the hose bracket.
STEP 59
MK99J020
Lubricate new o-rings with clean A/C compressor oil
and install the o-rings on the hose ends. Install and
tighten the suction (1) and discharge (2) hoses on
the A/C compressor.
STEP 60
MK99J023
Install the high pressure switch wire connector on the
engine wire harness.
STEP 61
MK99J011
Install the hood support/air cleaner bracket over the
top of the engine.
2
1
19. 2001-15
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 62
MK99J004
Use two M10 x 30 bolts to install the right side hood
support bracket mount on the frame. Do not tighten
the bolts.
STEP 63
MK99J024
Use two M10 x 30 bolts to install the left side bracket
mount on the frame. Do not tighten the bolts.
STEP 64
MK99J010
Use one M10 x 30 bolt to install the rear bracket
mount on the frame. Tighten the five M10 x 30
mounting bolts to specifications.
STEP 65
MK99J050
Install the exhaust aspirator tube on the muffler. Do
not tighten the clamp.
STEP 66
MK99J051
Use the M12 x 30 bolt, two flat washers and nut to
install the aspirator tube P-clamp on the exhaust pipe
mounting flange. Tighten the bolt and nut to
specifications.
STEP 67
MK99J050
Tighten the aspirator tube clamp to specifications.
20. 2001-16
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 68
MK99J049
Install the aspirator hose on the air cleaner inlet and
tighten the hose clamp.
STEP 69
MK99J007
Install the turbo air inlet tube between the air cleaner
elbow adapter and turbo inlet elbow adapter. Tighten
the clamps to specifications.
STEP 70
MK99J008
Install the wire harness connector on the air restrictor
switch.
STEP 71
MK99J073
See Section 9008 Radiator Removal and Installation
for instructions to install the radiator and cooler
assembly. Fill the engine and radiator with the
specified coolant.
21. 2001-17
Rac 7-92900 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 72
MK99J135
See Section 9001 A/C System - Recovery,
Evacuation, Charging for instruction to evacuate,
charge and add oil to the air conditioning system.
STEP 73
MK99K032
Open the battery access door and install the negative
battery cable on both batteries.
STEP 74
MK99J198
Fill the engine crankcase to the correct level with the
specified oil.
Start the engine and run at low idle for five minutes
with the deaeration tank cap off.
Check the fuel lines, hydraulic hoses and engine
coolant hoses for leaks. Check the operation of the A/
C system. Shut off the engine and if necessary, add
coolant to the deaeration tank. Check the engine oil
level (1).
IMPORTANT: After the engine has been run at the
normal operating temperature and allowed to cool,
check the coolant level at the recovery reservoir (2)
only. Do not remove the deaeration tank cap. If
necessary, add coolant solution to the coolant
recovery reservoir.
STEP 75
MK99H256
See Section 9007 Hood Removal and Installation for
instructions to install the support bar and hood.
2
1
22. 2002-4
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
AIR INDUCTION SYSTEM
MK99K132
When the air filter service monitor on the ROPS
instrument cluster illuminates, the primary filter
element needs service.
If the air filter service monitor illuminates with
frequency, or after the primary filter has been
serviced, check the following items for service:
1. Secondary filter element.
2. Restriction indicator switch.
3. Aspirated strata tube.
4. Aspirator safety valve.
5. Grille screen.
AIR FILTER ELEMENTS
The tractor is equipped with a two-stage air filter
system consisting of a primary (outer) filter and a
secondary (inner) filter.
MK99K083
The primary filter (1) is a high capacity filter designed
to provide optimum protection to the engine. The
primary filter can be cleaned as required between
filter changes. See the Operators Manual for
regularly scheduled filter servicing or replacement
intervals.
The secondary (inner) filter (2) gives extra protection
to the engine if there is damage to the primary filter.
The secondary filter cannot be cleaned and must be
replaced if dirty. See the Operators manual for
regularly scheduled replacement intervals.
12
23. 2002-5
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ENGINE AIR INDUCTION SYSTEM
Primary And Secondary Filter Element Removal
STEP 1
MK98C099
Shut off the engine and remove the key from the
switch.
STEP 2
MK98N142
Open the hood.
STEP 3
MK99K072
Release the four air cleaner cover latches.
STEP 4
MK99K073
Remove the air cleaner cover.
STEP 5
MK99K069
Pull the primary filter from the air cleaner.
STEP 6
MK99K070
Clean or vacuum any dirt or debri from the air cleaner
housing.
24. 2002-6
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 7
MK99K071
Pull the secondary filter from the air cleaner.
STEP 8
MK99K083
Inspect the rubber gaskets (1), the metal cover (2)
and filter material for damage. Replace the damaged
element.
STEP 9
MK99K087
To check the filter elements for dirt or holes use a
lamp inside the element and turn the element.
If the secondary filter is dirty, damaged or plugged,
replace the filter and proceed to Step 42.
If both filters are clean and not damaged proceed to
Step 12.
If the primary filter is damaged or plugged with oily
dirt replace the filter and proceed to Step 42.
If the dirt on the primary filter is dry proceed to the
next step.
2
1
2
1
25. 2002-7
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
PRIMARY FILTER ELEMENT SERVICE
STEP 10
MK99K088
Use compressed air from inside the element to
dislodge the dirt on the outside. Move the nozzle up
and down the length of the element while turning the
element.
IMPORTANT: The nozzle pressure must not be
more than 35 PSI (242 kPa).
STEP 11
MK99K087
Repeat Step 9 to check the clean filter for damage or
holes. Replace the filter if damaged.
RESTRICTION INDICATOR SWITCH REMOVAL AND TEST
STEP 12
MK00D308
Remove the wire harness connector from the switch.
STEP 13
MK00D305
Turn the switch counterclockwise to remove from the
air cleaner outlet tube.
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 2002-8
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 14
MK00D303
Install the test leads of a multimeter to the switch
terminals. Set the multimeter to ohms or continuity
testing. The multimeter should show an open circuit.
If the multimeter shows a closed circuit, replace the
switch and proceed to Step 40.
STEP 15
MK00D304
Connect the switch to a vacuum hand pump as
shown. Use the hand pump to slowly and carefully
apply vacuum to the switch. The multimeter should
show a closed circuit at approximately 690 kg/m2
(2
in Hg) of vacuum.
If the switch does not close at 690 kg/m2 (2 in Hg) of
vacuum or closes before 460 Kg/m2
(1.5 in Hg) of
vacuum replace the switch and proceed to Step 40.
If the switch closes at approximately 690 Kg/m2
(2 in
Hg) of vacuum proceed to Step 16.
AIR CLEANER HOUSING REMOVAL
STEP 16
MK00D309
Loosen the turbo inlet elbow clamp.
STEP 17
MK00D310
Loosen the air cleaner outlet elbow clamp.
Remove the air cleaner outlet elbow from the air
cleaner.
28. 2002-9
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 18
MK00D311
Loosen the air cleaner inlet duct clamp.
STEP 19
MK00D313
Loosen the aspirator hose clamp and remove the
hose clamp from the air cleaner.
STEP 20
MK00D312
Remove the four air cleaner mounting bolts.
STEP 21
MK00D280
Move the air cleaner housing rearward and out of the
inlet duct. Remove the air cleaner housing from the
tractor.
29. 2002-10
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
Aspirator Strata Tube Cleaning
STEP 22
MK00D322
If the dirt or debris in the air passages of the strata
tubes is wet, heavy, oily or soot is present, proceed to
Step 26.
If the dirt or debri in the air passages is dry, clean the
tube with compressed air directed into the inlet ends
of the tubes. Move the nozzle in a circular motion on
the vanes of each tube.
IMPORTANT: The air nozzle pressure must not be
more than 242 kPa (35 psi) or the vanes in the tubes
could be damaged.
STEP 23
MK00D270
MK00D323
Vacuum or wipe the dirt from inside the air cleaner
housing.
STEP 24
MK00D361
Place the aspirated strata tube in a solution of Case
IH Filter Element Cleaner (P/N A40910) and water.
Mix 57 grams (2 ounces) of cleaner for each 4 liters
(1 gallon) of water. The water temperature should be
38 to 66° C(100 to 150° F).
30. 2002-11
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
STEP 25
MS00D044
Keep the tubes in the solution for 30 minutes, then
turn the tubes over for about 2 minutes. Rinse the
tubes with clean water and dry completely.
NOTE: If there was soot or oil in the strata tubes
proceed to Step 26.
31. 2002-12
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ASPIRATOR SAFETY CHECK VALVE REMOVAL AND TEST
STEP 26
MK00D272
Loosen the hose clamp and remove the air cleaner
hose from the aspirator safety check valve.
STEP 27
MK00D273
Loosen the hose clamp and remove the valve from
the aspirator tube.
STEP 28
MK00D274
Loosen the hose clamp and remove the coupler from
the valve.
STEP 29
MK00D275
To check the aspirator safety valve for correct
operation, turn the valve outlet 180° up and down
several times. The gate inside the valve should move
freely from open to closed and back to open.
STEP 30
To clean the valve follow the same procedure as in
Steps 24 and 25. Repeat Step 29 after cleaning.
32. 2002-13
Rac 6-10120 Printed in U.S.A.
Template Name: SM_2_col
Template Date: 1997_01_13
Alt= to hide template information
Alt+ to display template information
ASPIRATOR SAFETY CHECK VALVE INSTALLATION
STEP 31
MK00D274
Install the coupler on the valve and tighten the hose
clamp.
STEP 32
MK00D273
Install the valve and coupler on the aspirator tube.
Turn the valve so that the arrow on the valve seam is
on top and points towards the muffler. Tighten the
hose clamp.
STEP 33
MK00D272
Install the aspirator hose on the valve and tighten the
hose clamp.