BUCKLING ANALYSIS

•

1 like•2,423 views

This Haiku Deck presentation contains photos from various sources including NASA's Marshall Space Flight Center, Defence Images, and individuals like sobolevnrm and woodleywonderworks. The presentation encourages the viewer to be inspired by the images and create their own Haiku Deck presentation on SlideShare.

Photo by NASA's Marshall Space Flight Center

This document discusses buckling of columns. It begins by introducing the concept of buckling as a failure mode distinct from stresses exceeding strength or unacceptable deformations. It then uses an example of two rigid bars joined by a pin to model the mechanics of buckling, defining the critical load as the transition between stable and unstable equilibrium. Finally, it derives equations for the critical buckling load of columns based on their end conditions, noting pinned ends buckle at the lowest load.

Buckling Analysis of Plate

Payal Jain

The document discusses using the differential quadrature method to analyze buckling in thin plates. It provides an overview of buckling and introduces the differential quadrature method as an efficient numerical technique. The method transforms differential equations into algebraic equations using sampling points. The document applies the method to analyze buckling in isotropic rectangular plates with different boundary conditions and aspect ratios. Results show the differential quadrature method provides accurate results using fewer grid points compared to other methods like finite element analysis.

Analysis of Functionally Graded Material Plate under Transverse Load for Vari...

IOSR Journals

Functionally gradient materials (FGM) are one of the most widely used materials in various applications because of their adaptability to different situations by changing the material constituents as per the requirement. Most structural components used in the field of engineering can be classified as beams, plates, or shells for analysis purposes. In the present study the power law, sigmoid and exponential distribution is considered for the volume fraction distributions of the functionally graded plates. The work includes parametric studies performed by varying volume fraction distributions and boundary conditions. Also static analysis of functionally gradient material plate is carried out by sigmoid law and verified with the published results. The convergence study of the results is optimized by changing the mesh size and layer size. Power law and exponential law are applied for the same material and set of conditions.

Sirris Smart Coating workshop - Easy-to-clean and Self cleaning Coatings - 19...

Sirris

The use of functional nano-metric easy-clean layers on material surfaces can reduce the dirt adsorption, facilitate dirt removal by rain, avoid dirt concentration /stripes and reduce cleaning efforts (longer intervals between cleaning and easier cleaning). OCAS, a Flemish steel research center has developed cost-competitive easy-clean coating layers that can be applied to a whole range of materials (painted metal, painted wood, plastics, glass, stone, and textile).

Analysis of buckling behaviour of functionally graded plates

Byju Vijayan

1. The document discusses the buckling behavior of functionally graded plates through two case studies. 2. The first case study analyzes the buckling of simply supported functionally graded rectangular plates under non-uniform in-plane compressive loading using classical plate theory. It finds that the critical buckling coefficient increases with the power law index and aspect ratio. 3. The second case study examines the buckling of imperfect functionally graded plates under in-plane compressive loading. It determines that the critical buckling load depends on factors like the load ratio, power law index, and amplitude of imperfection.

Stress Analysis of Functionally Graded Disc Brake Subjected To Mechanical Loa...

IJMER

This document analyzes the stress on functionally graded disc brakes subjected to mechanical loading. It models disc brakes with 40, 50, and 60 holes made of cast iron, FGM 1 (Al2O3-Al), and FGM 2 (Zr-Al). It finds that FGMs experience lower stress than cast iron. FGM 2 experiences lower stress than FGM 1. Stress increases with more holes and higher material variation parameter k. Displacement is highest for cast iron and increases with k for FGM 1 more than FGM 2. Thermal flux also increases with k and is highest for FGM 2 due to its higher conductivity. In conclusion, FGM 2 performs better than FGM 1 and

Thermal analysis of FGM plates using FEM method

Rajani Dalal

The document describes an M. Tech dissertation presentation on using finite element analysis to model the thermal behavior of functionally graded material plates. It discusses the objectives of analyzing FGM plates through literature review, developing a finite element computer code, and determining temperature profiles to compare with conventional materials. The introduction defines FGMs as composites with continuously varying material properties through the thickness to reduce stresses and improve bonding between dissimilar materials like ceramics and metals.

Neha Gupta CV

NIT Raipur

Prep seminar slides

Tejveer Parihar

This document discusses the development and characterization of polymer-ceramic composite materials with continuous fiber reinforcement and functionally graded properties for aerospace applications. Specifically, it examines quartz fabric-reinforced composites with a silicone resin and fused silica powder matrix that is compositionally graded across the thickness. The composites demonstrated improved mechanical and thermal properties over non-graded materials, including high flexural strength, low thermal expansion, and the ability to withstand high heating rates without delamination or charring. The results suggest these functionally graded composites are promising candidates for reusable high-temperature aerospace structures.

2014 bamboo a functionally graded composite material dr. pannipa chaowana

Theerawat Thananthaisong

1. Bamboo is a natural composite material made of long cellulose fibers embedded in a lignin matrix. Bamboo's microstructure and properties vary along its length and thickness, making it a functionally graded composite. 2. The study characterized the microstructure of Dendrocalamus asper bamboo through image analysis. Fiber volume fraction and vascular bundle concentration increased from bottom to top and inner to outer parts of the culm. 3. Specific gravity, bending strength and elasticity also increased from bottom to top due to higher fiber content and density. These properties correlated with fiber volume fraction, making bamboo grading useful for design.

functionally graded material

Er Shambhu Chauhan

This document outlines a student's workplan to study the fracture of functionally graded materials. The plan includes conducting a literature review to identify gaps and objectives, modeling the material and analyzing it using software, performing parametric studies on properties like reinforcement size and volume fractions, and submitting a final report. Experimental results are also presented on a photoelastic model that show stress distributions and crack propagation under loading. Numerical finite element modeling is found to match the experimental photoelastic results to within 5-8 percent.

Fgm sanjay

sanjay singh tomar

This presentation discusses functionally graded materials (FGMs). FGMs are composites with a gradual, continuous transition in composition and structure. They are classified as thin FGMs consisting of thin surface coatings, or bulk FGMs consisting of larger volumes. Common processing techniques for thin FGMs include vapor deposition and plasma spraying, while bulk FGMs can be made using powder metallurgy or centrifugal casting. FGMs have a variety of applications due to properties like resistance to delamination and high impact/abrasion resistance, and are used in industries such as aerospace, defense, energy and medicine.

PhD Dissertation Proposal Presentation

rightcoastrider

Buckling Analysis in ANSYS

Maha Hassan

The document provides an overview of buckling analysis in ANSYS. It discusses buckling of columns with well-defined end conditions, buckling of a special column, and second order analysis of a simple beam. The preprocessing, solution, and postprocessing phases of ANSYS are outlined. Step-by-step instructions are given for modeling each example and obtaining the buckling load using eigenvalue buckling analysis. Manual calculations are also shown for comparison.