This document provides step-by-step instructions for constructing a bamboo fishing rod. It describes selecting bamboo culms, flaming the bamboo to change its color, splitting the bamboo into strips, filling and pressing nodes, creating tapers, binding sections together, and final finishing steps like sanding and applying ferrules. The creator emphasizes patience, using simple tools, and taking time for sharpening throughout the building process.
Colagem de strain gages em célula de cargaKarine Silva
O strain gage é um extensômetro de resistência elétrica muito usado para medições que exigem grande sensibilidade a pequenas variações, como é especialmente o caso de células de carga. Neste trabalho será detalhado um processo de colagem dos strain gages em uma peça usinada de alumínio que será usada em uma célula de carga para medição de esforços de tensão e compressão de um eixo automotivo.
Colagem de strain gages em célula de cargaKarine Silva
O strain gage é um extensômetro de resistência elétrica muito usado para medições que exigem grande sensibilidade a pequenas variações, como é especialmente o caso de células de carga. Neste trabalho será detalhado um processo de colagem dos strain gages em uma peça usinada de alumínio que será usada em uma célula de carga para medição de esforços de tensão e compressão de um eixo automotivo.
Intro: How to turn a wooden pen on a lathe
Have you ever wondered how to make those awesome wooden pens? Well here is how you do it. At first the making of a American pen (that is this kind) will take you
about a hour and a half but once you have made a bunch you can make them in 15 minutes.
Image Notes
1. American style pen with Yellow Heart wood
Step 1: Supplies
For this Instructable you need these supplies. Most of these tools you can substitute for something else cheaper.
Lathe
Skew (the tool that you turn the wood with)
Wood ( i'm using yellow heart one of my favorites)
CA glue or Super Glue (thick and thin if possible)
Mandrel to hold the pen on with 3 bushings
Sand paper
Pen Kit or you could use pieces from a old pen that you don't use anymore
Paper towels
BLO (boiled linseed oil)
Drill press or equivalent
Clamp
Optional:
Micromesh to get the super shine
Beall buffing system to put on an awesome finish
Pen press
Intro: Homemade tobacco pipe
This Instructable is about how to make your own tobacco pipes at home. I didn't want to spend a lot of money for a tobacco pipe, so I decided to make one myself. Here
is how I did just that.
Step 1: You will need...
What you will need to make your own tobacco pipe:
- 1 Block of Bruyere wood
- 1 ferule
- different kind of grater
- a saw
- pencil
- a drill with different gimlets (Hand auger)
- one circle
- a Dremel like tool
- sand paper
- milling cutter min. 18 mm
- time (you will need a lot of it)
- a idea
For More information click below
https://bit.ly/36cFshF
After examining many, many workbench designs and almost settling on a German-style bench, I came across the 17th century French workbench of Andre Roubo. This design seemed to have surpassing versatility and an aesthetic superiority to every other design. In the construction process I learned of the trade-off between functionality, design, and ease of construction. I have made awkward-looking workbenches in one day which function perfectly. I've also made beautiful tables quickly and easily which are only useful as buffet tables. To make this workbench functional and attractive required that every surface be planed properly, and every corner be a perfect 90 degrees.
Building giant articulated hands carved from woodjessica30251
So I know we’re all going through a lot right now. This whole distancing thing is really starting to wear on us and that’ll never be truer than during this holiday season. That’s why I invented these. Stay 6’ away from your friends and family while doing all the activities just like you used to. It’s almost like they’re not even there!
The build all starts by planing down a bunch of basswood lumber that was reclaimed from a friend of mine. I chose basswood specifically for this project because of it's light weight and also because the grain is very even and straight, which makes it easier to carve. Each of these boards gets planed down and then sanded with the drum sander to exactly an inch thick.
I've had a Roubo-style workbench at the top of my
wish-list for quite a while after reading through
Christopher Schwarz's Workbenches: From Design &
Theory to Construction & Use. And, as luck would
have it, three years ago I helped a friend mill several
large trees that they had taken down and, in return,
he was nice enough to give me a bunch of really nice,
thick lumber to use for a workbench. So while that
finishes drying, I thought I'd build a bench from
common construction-grade lumber and experiment
with some design and construction ideas that I've
come across over the years.
Design and Build a Woodworking Workbench: Page 1
Intermediate Level Project
Start
Despite the reported average reply time, the conversation with COSJJ can take days or weeks. But one of our experts can stay on it and take care of it for you:
While we try to find every shortcut we can for reaching COSJJ customer service by email, we also recommend looking up the tips we have for your specific issue. Whether you're about to email info@cosjj.com or already have, it's worth checking for precise instructions.
How to sand and refinish hardwood floors yourself NajiyaAkhtar
Here is the best and most easiest answer for, how to sand and refinish hardwood floors yourself. step by step solution for, get a professional refinishing.
This is the tutorial for make the wheelchair wheel dryer by yourself. This is designed in function of the cocreation project with a person in a wheelchair..
TRADITIONAL BAMBOO PRESERVATION METHODS IN LATIN AMERICA - PRESERVACIÓN DEL B...Anibal Ruben Reyes
Guía bilingue (Inglés/Español) producida por la organización con sede en China, Red Internacional de Bambú y de Ratán – INBAR que refiere a los métodos tradicionales en América Latina para la selección, cosechado y curado del bambú.
Turkey vs Georgia Tickets: Turkey's Road to Glory and Building Momentum for U...Eticketing.co
Euro Cup Germany fans worldwide can book Euro 2024 Tickets from our online platform www.eticketing.co.Fans can book Euro Cup 2024 Tickets on our website at discounted prices.
Euro Cup international supporters can book Euro 2024 Tickets from our online platform Worldwideticketsandhospitality.com. Followers can book Portugal Vs Czechia Tickets on our website at sale prices.
Euro Cup fans worldwide can book Euro 2024 Tickets from our online platform www.worldwideticketsandhospitality. Fans can book Slovenia Vs Denmark Tickets on our website at discounted prices.
Euro Cup fans worldwide can book Euro 2024 Tickets from our online platform www.worldwideticketsandhospitality. Fans can book Ukraine Vs Belgium Tickets on our website at discounted prices.
Belgium vs Slovakia Belgium announce provisional squad for Euro Cup 2024 Thib...Eticketing.co
Euro 2024 fans worldwide can book Belgium vs Slovakia Tickets from our online platform www.eticketing.co. Fans can book Euro Cup Germany Tickets on our website at discounted prices.
Narrated Business Proposal for the Philadelphia Eaglescamrynascott12
Slide 1:
Welcome, and thank you for joining me today. We will explore a strategic proposal to enhance parking and traffic management at Lincoln Financial Field, aiming to improve the overall fan experience and operational efficiency. This comprehensive plan addresses existing challenges and leverages innovative solutions to create a smoother and more enjoyable experience for our fans.
Slide 2:
Picture this: It’s a crisp fall afternoon, driving towards Lincoln Financial Field. The atmosphere is electric—tailgaters grilling, fans in Eagles jerseys creating a sea of green and white. The air buzzes with camaraderie and anticipation. You park, join the throng, and make your way to your seat. The stadium roars as the Eagles take the field, sending chills down your spine. Each play is a thrilling dance of strategy and skill. This is what being an Eagles fan is all about—the joy, the pride, and the shared experience.
Slide 3:
But now, the day is marred by frustration. The excitement wanes as you struggle to find a parking spot. The congestion is overwhelming, and tempers flare. The delays mean you miss the pre-game excitement, the tailgate camaraderie, and even the opening kick-off. After the game, the joy of victory or the shared solace of defeat is overshadowed by the stress of navigating out of the parking lot. The gridlock, honking horns, and endless waiting drain the energy and joy from what should have been an unforgettable experience.
Our proposal aims to eliminate these frustrations, ensuring that from arrival to departure, your experience is extraordinary. Efficient parking and smooth traffic flow are key to maintaining the high spirits and excitement that make game days special.
Slide 4:
The Philadelphia Eagles are not just a premier NFL team; they are an integral part of the community, hosting games, concerts, and various events at Lincoln Financial Field. Our state-of-the-art stadium is designed to provide a world-class experience for every attendee. Whether it's the thrill of game day, the excitement of a live concert, or the camaraderie of community events, we pride ourselves on delivering a fan-first experience and maintaining operational excellence across all our activities. Our commitment to our fans and community is unwavering, and we continuously strive to enhance every aspect of their experience, ensuring they leave with unforgettable memories.
Slide 5:
Recent trends show an increasing demand for efficient event logistics. Our customer feedback has consistently highlighted frustrations with parking and traffic. Surveys indicate that a significant number of fans are dissatisfied with the current parking situation. Comparisons with other venues like Citizens Bank Park and Wells Fargo Center reveal that we lag in terms of parking efficiency and convenience. These insights underscore the urgent need for innovation to meet and exceed fan expectations.
Slide 6:
As we delve into the intricacies of our operations, one glaring issue emer
Denmark vs England England Euro Cup squad guide Fixtures, predictions and bes...Eticketing.co
We offer UEFA Euro 2024 Tickets to admirers who can get Denmark vs England Tickets through our trusted online ticketing marketplace. Eticketing. co is the most reliable source for booking Euro Cup Final Tickets. Sign up for the latest Euro Cup Germany Ticket alert.
Albania vs Spain Euro Cup 2024 Very Close Armando Broja Optimistic Albania Wi...Eticketing.co
Euro Cup 2024 fans worldwide can book Albania vs Spain Tickets from our online platform www.eticketing.co. Fans can book Euro Cup Germany Tickets on our website at discounted prices.
Euro Cup fans worldwide can book Euro 2024 Tickets from our online platform www.worldwideticketsandhospitality. Fans can book Denmark Vs England Tickets on our website at discounted prices.
Euro Cup fans worldwide can book Euro 2024 Tickets from our online platform www.worldwideticketsandhospitality. Fans can book Poland Vs Austria Tickets on our website at discounted prices.
Spain's Euro Cup 2024 Selections and Croatia's Group of Death Challenge.docxEuro Cup 2024 Tickets
Chelsea's Marc Cucurella is one of only three Premier League players included in Spain's preliminary Euro Cup 2024 squad as the Tottenham star with 11 goal contributions is overlooked
Akshay Ram on Adobe's Creative Strategy and Execution, the Present and Future...Neil Horowitz
On episode 271 of the Digital and Social Media Sports Podcast, Neil chatted with Akshay Ram, Product Manager for Adobe, who also has a lot of knowledge and insight into sports creative.
What follows is a collection of snippets from the podcast. To hear the full interview and more, check out the podcast on all podcast platforms and at www.dsmsports.net
Spain vs Italy Spain at Euro Cup 2024 Group, Fixtures, Players to Watch and M...Eticketing.co
Euro Cup 2024 fans worldwide can book Spain vs Italy Tickets from our online platform www.eticketing.co. Fans can book Euro Cup Germany Tickets on our website at discounted prices.
Euro Cup fans worldwide can book Euro 2024 Tickets from our online platform www.worldwideticketsandhospitality. Fans can book Spain Vs Croatia Tickets on our website at discounted prices.
Results for LtCol Thomas Jasper, Marine, for the 2010 Marine Corps Marathon held October 31, 2010, marking the 35th annual marathon known as "The People's Marathon."
An impressive finishing time of 3:46:39, placing 324th in the Male division ages 40-44.
Turkey's Euro 2024 Squad Overview and Transfer Speculation.docxEuro Cup 2024 Tickets
Vincenzo Montella has announced a preliminary 35-man squad for Turkey ahead of the UEFA Euro 2024, which includes three Serie A players, Hakan Calhanoglu, Kenan Yildiz, and Zeki Celik
Turkey's Euro 2024 Squad Overview and Transfer Speculation.docx
Bamboo rods marcelo calviello
1. Well I decide to share with all the ones
who want it, the complete construction of
one of my rods. For this purpose I leave
the blank that I had made for another
rod order and begin the new Guru from
zero.
1 Selecting the culm
When I talked with Marty he told me that
he like's full flamed rods, so I have to
look for a special culm to do the job. I will
look for a medium culm with dense walls
for the butt and the medium pieces and
the 2 tips will be done from the same
culm with low wall measure.
I select this type of culm because if I
work with a big one, when I flamed, the
cane will get deformed into an oval form
with the heat treatment.
I will use the 3 / 3 nodes staggering in
this rod so I need two full culm pieces to
the whole rod. The dense one for but &
medium and the other for the 2 tips. I cut
this pieces to measure and mark the
down side Green for Butt, Black for Mid
and Red for Tips. This allows me in
coming steps to plane strips always in
the same direction.
Important: Made a full spliting check
along the two culm pieces.
2. 2 Flaming the culm
Time and patience. Remember this. With the
same process we can turn the cane into a full
flamed tone or get it burned. This is only a
matter of time and care. I always think in this
step that cane and grass are the same thing,
so I slow all my process. When to stop? the
cane or many canes will tell you. But remember
that cane have many layers. The first one will
go with the heat treatment but the second is in
the one we want to change the color. This
changing will take place in many different
stages and colors.
a. first layer goes out with heat.
b. very light flamed
c. light flamed
d. flamed
e. medium flamed
f. full flamed
g. dark flamed (I never try this one)
I do this work outside and with a heat gun
with a trigger that let's me stop fire instantly.
This gun is connected to gas and I used always
full power blue flame and work at about 12/15
inches from the cane.
The whole process take's me about one
morning.
To get this stage finished I take out all
diaphragm at each culm.
3. Splitting
This where real connect with cane begins. In the
whole process you can appreciate the special
particularities of the rod you had selected.
After many search for this fundamental stage I
arrived after many different test to what I called
"My split Machine". Trying to avoid any
commentaries I must say that I called "my"
because I own it...
Perhaps is an obvious stuff but is great to take
care of my splitting work. In the zoom picture you
can appreciate how simple it is, just wood and
two steel nails. The head of the nail will hetp
turning down the strips along the splitting of
each one. The only thing to do is match the main
split. I always make my strips over measured
and them with a knife I take them to real
measure.
Here you can see how my machine work, in the
full process. The half culm in two parts, them two
in other two, and this ones in other two. Eight
perfect strips, 6 for the rod and two for spares
Here you can see how my machine work, in the
full process. The half culm in two parts, them two
in other two, and this ones in other two. Eight
perfect strips, 6 for the rod and two for spares
4. Filling & straightening nodes is one of the most
important job involved in making a rod. All the work,
time and patience that we spend in this stage will be
recovered in the Planing job.
Filling the nodes
Simple tools, our eyes, our hands, two limes in two
different thickness and shapes and two C clamps.
Another important thing that you have to take care is
the place to work. Personally I like to do it outside,
where mi mind is more suitable to make a relaxed
work. I found into my house gallery a handrail that
give me a firmly ground and a nice garden looking. Also
"the boss" (wife) don't get angry because of the dirt
involved with this work.
5. I support the strip with the C clamps and start working with the big file in the pit side of the
node. I liked that this job finish with a plane surface.
Them I attack the upside of the node. I work first with the big file and them I get the work
finished with the little one, at the point that I get a polish surface. In the upside of the nodes I'll
try to continue the round form of the strip and leave any node a little over-measure. This will
disappear whit the pressing stage.
6. Pressing the nodes
Tools involved, again eyes, hands, a
variable heat gun and a vice.
From those tools that I was able to
choose I had tested many, and
selected the Metabo Heat Gun and
the Record Vice (mod. 50 / 51) no
commercial interest just the ones I
think are the best.
I bought the two models of vices, one
is fixed on my workbench and the
other one follows me wherever I go.
Steps in the pressing nodes stage.
a. heat the node sides.
b. press the node sides.
c. heat the node faces.
d. press the node faces.
When I heat the nodes I always take
care that they don't get burned time
and patience will tell us when it is too
much.
7. This is like the nodes are in their different stages: before & after
The first 30 angle
After pressing nodes I must get perfect straight strips, so with the heat gun I turn all the
strips to a fine straight shape. To make the first angle I have developed a great machine, I
called the "Angle machine". This tool turns a difficult work into a very easy step.
(Rodmakers, specially hand planers take a look at this tool
8. As you can see the machine
consist in two forms with it's
30 angles inverted, so when
I place a strip and get it
tight, it turns into a 30
angle and all my planing will
go with that attack. Also
because the strip is firmly
holded we can work only
with one hand
Here you can see a zoom
view and how the strips are
placed into the machine.
To make this job I use a
Record Plane 60 1/2
sharpened at 45 angle This
plane because of it's wide is
more comfortable and easy
to control.
Press on picture to play video
9. Triangulation 60 angle
After I got my 24 strips with the first 30 angle from the Angle
Machine I work in a form I'd made for triangulation, with 4
fixed 60 angle different measures, that are the most used by
me in all my tapers
Here, you can see the strip in his 30 angle stage and
finished at 60 angle.
10. An advice about sharpening
Another day is finishing and as Jeff (Ghome) told me a
big glass of wine is near my computer. Sharpening is
one of the most important things to take care in the
whole process of making a rod.
I read many, many advices talking about the best way
to do this job, and I found that as always the simple is
the best.
I use a square glass and place over sand paper of
different grits starting at 220 and them 360, 500, 800
and finishing at 1.000 this gives a mirror finish that
looks & work great for me.
Many times along the hole rodmaking process you get
tired so you must take a time for you. Sharpening is
really a good investment, you can do it in any place,
with a glass of wine near you and really this time will
pay for it self.
I helped my sharpening with two tools, a Veritas
Precision Honing Guide and a right angle square that I
marked at 30, 35 and 45 angle.
Don't forget this advice, sharpening is one of the must
important jobs to be done, you will listen along the
planing when your blades need to be sharped.
11. It's binder time
My binder was the first machine that I made. I
remember that I'd take parts from here and from there,
please don't tell my boss, but the wooden handle is from
our Thomson table, she will kill me if she knows. Many,
many wars we fought together and he show his scars
proudly, many rods and many dreams were tied there. I
love this machine, because he is faithful and help me to
get great rods. Many times when customers visit my
shop tell me that it's time to make a new one, but with
him I made my first rod and with him I will made my last
one.
Well this stage is simple the only thing to take care is
about learning the knots and work with a great machine.
The more straight you obtain the rod pieces, with the
oven treatment the will be copied and the planing stage
will be better.
Press on picture to play video
12. Oven treatment
I'd made two different types of oven along the years. One is an
electric one that give's me about 400 degrees Fahrenheit and
another, that is the one I prefer, a Gun Oven that gives me
about 400 degrees Fahrenheit with the heat gun set in max.,
200 F in medium, and 100 at low.
Why I select the Heat Gun Oven?
With a rod flamed like this one, I prefer a very slow treatment,
so I do it at 150 F for about 40 minutes in one side and
another 40 m for the other side. I liked this way, because I
think that a slow process is better than an aggressive one. The
heat treatment is done by heat air circulating along the cane,
that for sure will not cook it. Also, because the only reason for
this is to drive moisture from the cane, why more? After this,
the project rod always will be keep into my drying cabinet, that
also is at 80/100 F
13. Ferrules impregnation BOBFS I
Here we start with the BOBFS, so to give some protection to this part of
the rod I impregnate the sections where the ferrules will be made.
To do this job I impregnate by immersion the three parts where the
ferrules are, the two tips and the mid section. I leave there for about one
day, and they will cure in the drying cabinet along the rod process
continues
Preparing for Planing: Removing the enamel
Involved tools:
3M sandpapers blocks, 1 little block, sandpaper in 220
and 600 grit, rough form and scraper.
I like to take out the enamel sanding each strip first
with the 220 and them with the 600 sandpaper. This
must be a careful job because I don't want to take
out any powerfiber. For that I use my rough form little
60 angle and carefully sand each strip. Only if I find
any problem to solve I use my LN scraper.
14. With the little block loaded with 600g
sand paper I light sand each strip to
get a clear finish.
It's planing time
Tools involved:
For my planing I like to use the same block planes for each
piece of the cane, so when I got them sharpened I begun
with the Record 9 1/2 with his blade sharped at 30
degrees. Follows my Old Stanley 9 1/2 sharped at 45
degrees. Along the planing I like to verify measures so I
do it with the caliper in this stage.
Them begun the final planing for what I use 2 different LN
9 1/2 with different blade exposure. In this stage I verify
with my micrometer.
For what I use 4 different blocks planes?
1. This force me to do the job in four stages. (Time &
patience)
2. I don't like to sharp any blade in the middle of a piece.
So when I get finished a piece I sharp all my blades again.
3. I use my R to take the first shape. Them with my S I do
the real work. I like it because is very light. And with my
LN's only the fine finish work
15. One thing before planing
I was thinking to do something new for me with this rod, so I
just made some flamed marks only for looking. And I really like
them.
I used a jewelery torch that gives me a real blue flame, so this
would allow me to draw if it wanted.
Look that I care in the butt piece the number three (up to
down), the space for the grip and for the sign mark.
Planing Form & Digital Depth Gauge
I made my planing form and really after that I
can take any challenge.
It's 70 inches long with 30 stations placed 2,5
inch one to the other. As I told sometime ago,
it take's me a month of full work to get it
ready and working.
My depth gauge is a digital one that allows
me to see mesures in mm and in inches. It is
placed always in his steel bed with a plastic
protection for the sharp 60 angle point
16. Planing (BOBFS II)
Well guys I just got the butt finished. I suppose that this piece was not the one you are interested,
so take a look and we will go over the first BOBFS in the medium piece.
The most difficult part of the job is setting the forms, them you must go just ike with any planing
situation.
Also in this case I added a little movie just to show my
forms in an up view with a strip into it.
Press on picture to play video
17. Planing (BOBFS III)
When I got finished the 6 strips of each piece, I put them together, been carefully that nodes
match the 3 x 3 staggered system and them will be tapered with paper tape
Planing (BOBFS IV)
There you can see a sequence of how BOBFS are made. I had designed a special form that make's the
job easy and accuracy. The form was made in steel with a hard temper to allow that always will keep in
shape. The depth of the form bed is 1.8 mm (0.071 in)
18. Planing (BOBFS V)
Two tools are involved in the BOBFS making process. The ferrule form and a Finishing Sander loaded
with 120 grit sandpaper first and 400 grit sandpaper for finish. The FS works just like a plane over the
form.
19. Gluing (BOBFS VI)
To got my rods glued I use an ureafolmaldehyde glue that closely match the color of the cane. This
glue, works with a hardener that must be weighted to exactly proportions that are advised in it's
packaging. This proportions, are related with room's temperature. So when I get the correct
temperature, the measure table will indicate the correct proportion of hardener to use. To weight it I
use a jewellery scale. The glue allows me 40 minutes to complete all the job. Another tool's that must
be used are a tooth brush and the binder
20. This is very important stage in the BOBFS making process. I
must align perfectly the six strips to get a perfect hex ferrule,
so here is where I have to put all my attention because any
imperfection here could not be corrected later when the glue
dry. That's the reason why I love my binder. I know that it
will work perfectly and all my caring are with the ferrules
This is the finished glued rod
21. The little BOBFS story
For the ones who ask about how we
arrived to our BOBFS, here in the story in
pictures. From top to down.
1- The first design with a truncated bamboo
ferrule
2- The broken ferrule of my son's SAGE.
Here
is when my point of view about bamboo
ferrules was changed.
3- Our first swelled bamboo ferrules.
4- My 2MBFS (Mini metal bamboo Ferrule
system). This ferrules own inside a little
metal females and a metal tip in the male
At last with Jorge when the design of new tapers were made the new concept of the BOBFS was born.
22. Removing thread and glue
Well because I want to do this job under the sun, for
better looking, and tomorrow will rain here, I accelerate
the drying process in the drying cabinet so the rod is
ready to work. For this job I use three blocks with sand
paper 220, 400 and 800 for the finish.
The finish will be the result of a hard polishing work, it's
take about 6 hour to get the job completed.
Wrapping (BOBFS VII)
Thank you very much for the ones who help me with the
colors decision. Classic Chestnut wraps with Violets tips was
the winner option in the poll 12 votes over a total of 34 (33
%).
The wrapping section that I always made is 20mm more than
the BOBFS female hole (in this case 70 mm) so the wrapping
area will be 90 mm
23. For wrapping the BOBFS I like to use Pearsall's Naples and
doing the 3 ferrules is just like wrapping a complete rod, just
be prepared for that.
I use for the job my Golden Witch Wrapping Machine with
some modifications of my own
This would result in a complete wrap of 90 mm.
24. Varnishing (BOBFS VIII)
For varnish I like to first made two coats of Alchemist using a fine brush and waiting
aprox. 1 or 1 1/2 hour in between.
After 1 1/2 hour later, I varnish the ferrule (female) section, in this case using my
varnish I do it by dipping for a total of 9 times including the ones (3 times) when the
hole section rod will be varnished. Each time with the help of paper towells I take out
any excess of varnish out and into the BOBFS female hole
25. Signing
Not much to say about this stage. I use black indian ink and a fine pen. I have to find the correct
splines for the tips before sign them.
26. BOBFS IX (Ferrule male Tips)
As I told you I like to protect the butt tips with a little metal tip. I use aluminum but could be
made with any metal. For this job I use my Sherline lathe an aluminum bar. I take two measures
of the butt tip, one over the angles and the other over the flat. For example if the first measure
is 6.05 mm and the other 5.60 mm I use 5.85 mm to made tip
When I made the hole of the tip I always leave a 1 mm wall at the
tip.
27.
28. The grip
Argentina is a very difficult place to find finish stuff but a really good one to find quality materials. This
happens at the time when I was looking for cork. Finally I found a fine quality, they call "grade AAA"
Portuguese cork. The cork came in pieces of 13 in x 2.8 in and 1/4 inch of depth. So I was in the
necessity of a good tool to make the job from the beginning. In the picture sequence that follows you
can take a look to the complete process
29. Them the rouged grip will stay in the drying cabinet for a day and then will be ready for shaping.
I don't like to use any mould or shape plane I have the wanted grip in my mind, so I go for it.
Finally I cover all the grip section with plastic
tape to protect it in the coming work.
30. Wrapping time
Well the rod was sleeping in a warm place for about 24
hours and it's ready for some wrapping. My drying
cabinet maintains a constancy temperature of 90/100
Fahrenheit degrees and 20 % of humidity.
I had to move all my shop to get some pictures, because
I like to show you in the better way.
This is my wrapping machine from GW. I'd made some
modifications that allow me to work more comfortably.
Two wire thread tensors make's possible to go back
about 10/15 threads rounds if something don't satisfy
me.
Also some tool's that I always use
31. One of the first things I do to test my day, is the grip wrap. Really I have days that I had to change
my plans and make something else. That's the reason I like to work always with three or four
different rods in different stages.
After I got finished the grip wrap, the first coat of Alchemist will be done to avoid it to move
Selecting Guides
Snake Brand is our first choice for our
new line of rods, that's because of it's
quality and the great service that
Michael and Susan give to us.
All our rods take's an Agate striping
guide and black nickel guides
32. Placing the guides
Every time we made a taper we also design where the guides must be placed to get the best
action, so we had make a special wood piece with all our tapers and guides display "formulas”. To
place the guides we use paper taper.
Some wrapping
Wrapping is something like flyfishing or golf you never stop to learn. I'd tied many rods along my
rodmaking, but a new one is really a new challenge. One thinking that I learn with many rods
wrapped in my life and I'll never forget is that "rush is the best enemy of perfection"
33. When I got all the rod wrapped I like to take time between
varnish to start tuning the BOBFS. If I done the correct job
when planing the ferrules taper of the male may goes into
the female ferrule comfortably not loose just comfortably.
Because is difficult to explain this sensation I made a little
movie that tries to shows this to all of you.
Well the first thing to do is cleaning all the
female hole with alcohol with the help of a Q-
Tip. Then we made the 2 ton. Epoxy coat with
the help of an extended Q-tip that allows to
get into the bottom of the hole. When I'm
completely sure that all the hole surface was
coated I take out any excess from the borders
and put the rod piece to roll in the wrapping
machine. I made a rotary tool that can be
attached to the machine so while the epoxy
dries I can make another wrap varnish. When
the female is finished I dip the male up the
ferrule wrap.
Press on picture to play video
34. BOBFS (Pining ferrules males)
To make this job I use a Dremel tool, steel wire and a little hammer. This is very simply but
must be done with extreme careful because we can lost all the work here. After getting the
little cups pinned I just polish to return to the good looking cup.
Making the Reel Seat
For making the reel seat I'd selected a native hard
wood called Guayabira, this trees grows at the rivers
banks in our state of Misiones where the famous
Iguazu Falls are placed. Also I made all the silver
hardware but I avoid to show all this process because
it will take's me another thread. I made all the Job at
my Sherline lathe with the help of common tools and
specific ones that I'd made for this purpose. When I
got the reel seat shape finished I polish it with a "doll"
with nuts.
35.
36. Well 21 days of full work. This is the finished second Guru
Rod: Guru764 3/2 specially made for Mr. Martin J. Keane