54645 01 vsp_vs300_fh5_dcah

VS300FH5 Hot Sheet

System Model # VSP-VS300FH5-DCAH
Software Version # 41
EPN # 2668

Base PCBA - PN 54646-01
PCB VS500Z - PN 22972 Rev D

Base Panels
VL401 (LCD Lite Duplex) – PN 54665
VL403 (LED Lite Duplex) – PN 54664
VL406U – PN 55350

Optional Base Panels
VL200 (Mini) – PN 55123
VL240 (MVP240) – PN 55080
VL260 (MVP260) – PN 55081

Template used: 40732_C.pdf 11/08/2007
54645-01_97_B.pdf 11/29/2007

http://www.MyPoolSpas.com Wholesale Pool and Spa Parts
Page 1 920-925-3094
54645-01_97_B

System Revision History
System PN EPN Date Requested By Changes Made
54645 1710 02.14.2007 Balboa New system
54645-01 2668 11.21.2007 Balboa Software update to v41, model now VS300FH5
54645-01 2668 11.29.2007 Balboa Correction to Power Requirements

Page 2 920-925-3094
54645-01_97_B

Basic System Features and Functions

Power Requirements

System Outputs
Setup 1 (As Manufactured)

Optional Panels

Additional Options

Page 3 920-925-3094
54645-01_97_B

Basic System Features and Functions
Any time you change a DIP Switch, other than A1, you must reset Persistent Power Up Display Sequence
Memory for your new DIP Switch Settings changes to take effect. If you do Upon power up, you should see the following on the display:
not reset Persistent Memory, your system may function improperly. Three numbers in a row, which are the SSID (the System Software
ID). The third display of these numbers is the Software Version,
To reset Persistent Memory: which should match the version of your system. For example, if these
Power down by disconnecting power source from spa. three numbers are , that is a VS511SZ at version 38.
Put a jumper across J43, covering both pins. (See illustration below) Displayed next is: “ ” (indicating the system is configured for
Power up by connecting power source to spa. a heater between 3 and 6 kW) or “ ” (indicating the system is
Wait until “ ” is displayed on your panel. configured for a heater effectively* between 1 and 3 kW).
Power down again. “ ” should appear for all VS models running at 240VAC.
Remove jumper from J43 (May also move to cover 1 pin only) “ ” should appear for all VS models running at 120VAC, as well
as all GS models. (*A heater which is rated at 4 kW at 240VAC will
Power up again.
function as a 1 kW heater at 120VAC.)
“ ” will appear to signal the start of Priming Mode.
About Persistent Memory and Time of Day Retention:
This system uses memory that doesn’t require a battery to store a variety of
At this point, the power up sequence is complete. Refer to the Reference
settings. What we refer to as Persistent Memory stores the filter settings,
Card for the VS or GS System model of your spa for information about how
the set temperature, and the heat mode.
the spa operates from this point on, including how to adjust the Time of
Day if using a Serial Deluxe style panel.
Persistent Memory is not used for Time of Day. Only models with a
Serial Deluxe panel installed (VS5xxDZ and GS5xxDZ) can display the
time. However, during power loss to the spa, the system will lose the
correct time, and reset to 12:00 PM when power is restored.

J43

TST RST
FUSE 20A 250V J47 J6 J43
J46

F7 J29
K6 J23 J50 PUMP OZONE
K1 J23 J29
F1 F5, F3A 250V J20
J20
J17/26

J6
E.GND

G

G

K5
J90

G C
C

C
FUSE 3A 250V
C
C

C
C

C
C

S1 TST
G

G
G

J50

W7
W4
G

G
G

J12
W1 K8 K5
F4 FUSE .3A 250V
SWITCHBANK A
T1 K9 W3
W2 K4 K1
SWITCHBANK A
J1 J1A
J10
J18
F2 U4
J13

J2A T0.25A 250V
NEUTRAL
WHT AC J1
J18

W1 J58 J57
1 2 3
K3 K3
U4 J12
K2
J2
VS100
P/N 22964_B MADE IN U.S.A.

J26 F4
Balboa

J43
© 2006

F2 LINE
K2

J13 TST RST
BLK AC
BALBOA INSTRUMENTS, INC. 2-SPD S1 J6 J43
J60 J22 J44 VS500Z EXT RLY
J6 J7 J8 J7 J8
E.GND

P/N 22972 REV D
J9

S1 TST EXT.
T AUX. F VAC MADE IN U.S.A
V
SWITCHBANK A RLY
L SEN. A SEN. B COPYRIGHT 2005 HEATER
A
SWITCHBANK A SEN. A SEN. B

J43 on VS5xxZ and VS300 Series Main Board Shown. J43 on VS100/GS100 Series Main Board Shown.
J43 on GS5xxZ Series is located in approximately the same position.

Page 4 920-925-3094
54645-01_97_B

Wiring Configuration and DIP Settings
Setup 1 (As Manufactured)

Black jumper required. Ozone must be same voltage as Pump 1.
Do not remove. Ozone runs with Pump 1 low-speed.
FUSE 3A 250V J29
CLASS G FUSE 30A K6 J23 K1
F5
J73 W10 F1
2-Spd P1
J20

Ozone

FUSE 3A 250V
WHT AC
T

C
Light
12V
C
C

G
G
G

J11 J15 J25 J63

W1 K5
W2
T1
NEUTRAL

F4 FUSE .3A 250V
WHITE

J1
BLACK
HOT

J18
TORQUE
RANGE
RED
HOT

FOR TB1: K3
K4 27-30 IN. LBS. U4
K2
TB1
J32 J33
J43

F2
RED AC
BALBOA INSTRUMENTS, INC.
J7 J8 VS500Z

Balboa HTR2 HTR1 J6
E.GND

P/N 22972 REV D

S1 TST MADE IN U.S.A
SWITCHBANK A SEN. A SEN. B COPYRIGHT 2005

Heater rated @ 240V
5.5 kW (Approx. 1.4kW @ 120V)

WARNING: Main Power to system should be turned OFF BEFORE adjusting DIP switches.
WARNING: Persistent Memory (J43) must be RESET to allow new DIP switch settings to take effect. (See Persistent Memory page)

SSID # Wiring Color Key
120 Volt Connections
100 240 Volt Connections
59 Black AC Jumpers
41 12 Volt Connections
A1, Test Mode OFF
A2, Un, LT, TD, TU Relay Control Wires
P1, P1, TE, LT A7, Mode changes allowed J43
Memory Board Connector Key
A4, N/A (must be OFF) A9, P1-low timeout, Table 1 Reset
A5, P1-high timeout, Table 1 A10, High Amp mode 1 Typically Line voltage
2 Typically Line voltage for 2-speed pumps
Panel Button Assignments Panel Button Positions
3 Neutral (Common)
1=Unused
1=Pump 1 3=Temp Down 1
4
2=Light 1
2=Pump 4=Light
4=Temp Up 1 2 3 4 3 Ground
4 2
Note flat sides in connector

Page 5 920-925-3094
54645-01_97_B

DIP Switches and Jumpers Definitions
SSID 100 59 41 Base Model VS300F
DIP Switch Key
A1 Test Mode (normally OFF)
A2 “ON” position: Button layout will be: Pump 1, Light, Temp Down, Temp Up *
“OFF” position: Button layout will be: Unused, Pump 1, Temp, Light
A3 “ON” position: use Mini Panel *
“OFF” position: use Lite Duplex or Digital Duplex panel
A4 N/A (must be OFF)
A5 Pump 1 high-speed timeout, see Table 1 Table 1 Pump 1 Timeouts
A6 “ON” position: 50Hz operation
“OFF” position: 60Hz operation A5 A9 Low-spd Hi-spd
A7 “ON” position: Standard mode only
OFF OFF 2 hours 15 min
“OFF” position: Std/Ecn/Sleep mode changes allowed
ON OFF 2 hours 30 min
A8 “ON” position: temperature is displayed in degrees Celsius
OFF ON 15 min 15 min
“OFF” position: temperature is displayed in degrees Fahrenheit
ON ON 30 min 30 min
A9 Pump 1 low-speed timeout, see Table 1
A10 “ON” position: heater is disabled while the high-speed pump is running (low amperage mode)
“OFF” position: heater can run while the high-speed pump is running (high amperage mode)
* Panels with button layout are not compatible when A2 or A3 is ON.
Note: No blower or second pump available.

Jumper Key
J43 When jumper is placed on 2 pins during power-up, system will reset persistent memory.
Leave on 1 pin only to enable persistent memory feature.

WARNING:
Setting DIP switches incorrectly may cause abnormal system behavior and/or damage to system components.
Refer to Switchbank illustration on Wiring Configuration page for correct settings for this system.
Contact Balboa if you require additional configuration pages added to this hot sheet.

Panel Button Positions
1
A3: OFF 1 2 3 4 3
4 2

A3:ON 1 2 3 4

Panel Button Assignments
1=Unused 3=Temp
A2: OFF 2=Pump 1 4=Light

A2:ON 1=Pump 1 3=Temp Down
2=Light 4=Temp Up
Page 6 920-925-3094
54645-01_97_B

Ozone Connections
Ozone voltage must be wired to same voltage as Pump 1.

Ozone Connector Voltage: The VS300/VS300F circuit board is factory configured to deliver a preset voltage
(120V or 240V) to the on-board ozone connector (J29). See the ratings table on the wiring diagram attached to
the cover of the enclosure for the configured voltage. For 240V output W2 connects to Red AC and for 120V
output W2 connects to White AC.

The voltage to the ozone connector can be changed in the field if required. W2 just needs to be set for the
required voltage. Reminder: Ozone voltage must be set to match Pump 1 voltage.

Balboa Ozone Generator: If the board is set up to operate a 120V ozone generator, the connector on the ozone
generator is likely to be configured correctly, but should be compared to the illustration below.

If a 240V ozone generator is required, be sure the red wire in the ozone cord is positioned in the connector next
to the green ground wire as described below.

Note: A special tool is required to remove the pins from the connector body once they are snapped in place.
Check with your Balboa Account Manager for information on purchasing a pin-removal tool.

Balboa Ozone connector configuration for 120V 60Hz B
Line - Black conductor
Use this slot for the leftover Red conductor
Common - Install the White conductor here for 120V ozone
G
Ground (Green) conductor

Flat sides of sockets as shown
Balboa Ozone connector configuration for 240V 60Hz B
Use this slot for the leftover White conductor
Common - Install the Red conductor here for 240V ozone
G

USE 3A 250V J29
J20 F1 Use this slot for the leftover conductor
Common - Red for 240V or White for 120V ozone (See W2 wire)
FUSE 3A 250V
W
Light
12V

W2 wire determines voltage
W

K5
W2

J1
J10

Page 7 920-925-3094
54645-01_97_B

Duplex Panel Configurations

Jets Warm

DIP switch A3 must be OFF
Light Heat Cool
SETUP (AS MANUFACTURED)

VL406U
PN 55350 with Overlay PN 11947
Heat
Connects to Main Board terminal J1
Cannot convert to VL406T by changing overlay
Jets Light Cool Warm

Heat

VL403 (Lite Digital)
Connects to Main Panel terminal J1

VL401 (Lite Digital)


DIP switch A3 must be ON
VL260 (MVP260)
OPTIONAL PANELS



VL200 (Mini Panel)

VL240 (MVP240)
MVP240)
Page 8 920-925-3094
54645-01_97_B

54645 01 vsp_vs300_fh5_dcah

Recommended

Recommended

More Related Content

What's hot

What's hot (7)

Viewers also liked

Viewers also liked (17)

Similar to 54645 01 vsp_vs300_fh5_dcah

Similar to 54645 01 vsp_vs300_fh5_dcah (20)

More from Accurate Pool & Spa Services, llc

More from Accurate Pool & Spa Services, llc (20)

54645 01 vsp_vs300_fh5_dcah