This document provides maintenance schedules and lubricant recommendations for equipment used on offshore rigs, jack-ups, lay barges, and dredges. It lists various pieces of equipment and recommends lubricants and maintenance intervals. Lubricants recommended include molybdenum disulfide greases, gear oils, and chain lubricants from Transol's product lines. Maintenance is generally recommended every 150 hours of operation or during equipment movement. Proper lubricant selection depends on the operating temperature range.
(Best) ENJOY Call Girls in Faridabad Ex | 8377087607
Ts moly marine & offshore applications
1. Products for Offshore Rigs, Jack-Ups, and Others
Equipment Interval
Blower Assembly Each 150 hours of operation
Exciter Generator Bearings Each 150 hours of operation
AC Generator Each 150 hours of operation
Spud Racks and Pinions During elevation or lowering operation
Spud Guides and Ways During elevation or lowering operation
Final Drive In-board Bearings During elevation or lowering operation
Final Drive Out-board Bearings During elevation or lowering operation
Final Drive Gear Teeth2 During elevation or lowering operation
Intermediate Out-board Bearings During elevation or lowering operation
Spud Motor Bearings As needed or at 150 hours
Intermediate Gear Unit During elevation or lowering operation. Change at overhaul.
Skidder Ways During skidder movement
Spud Primary Gear Box Prior to elevation or lowering operation
Note: The SAE number of gear oil is determined by the temperature where the rig will be working. Always follow the manufacturers specifications. Where an SAE 90
SAE 80W90 Gear Oil or TS-301 Moly SAE 85W140 Gear Oil. For temperatures above 100°F, use TS-302 Moly SAE 140 Gear Oil.
1
Do not overlubricate. Use the 150 hour as a starting point. Remember, lubricate only as needed; twice monthly may be often enough.
2 When oil pans are used on final drive gear, use TS-302 Moly SAE 140 Gear Oil
Products for Lay & Derrick Barges & Dredges
Equipment Application System
Air Compressors (Piston Type) Forced or Splash Circulation
Anchor Lines & Cables Hand, Brushed, Spray or Vat
Antiseize Compound
Bearings (Oil Type) Splash or Forced Circulation
Bearings, Plain or Anti-friction (Grease Type) Hand Applied or Central System
Crankcase Add to Motor Oil
Drive Chains:
Enclosed Splash or Forced Circulation
Open Hand Applied
Flex Couplings:
Oil Type: NOTE: DO NOT USE WITH Splash or Circulation Pump
INTERNAL CLUTCHES OR FRICTIONS
Grease Type Hand Applied or Central System
Friction Pins, Nuts, Bolts, Valve Stems, Anchor Hand Applied Aerosol Cans
Pins
General Greasing:
Bronze Bushings Hand Applied or Central System
General Cleaning:
Galley, Deck, All Floors, Walls, Engine Room, Spray, Brush or Dip
Gas Free Tank, Etc.
Heel Pins, Fair Leaders & Bearings
Hydraulic Systems Add to Hydraulic Oil
Motors, Gearhead Ring or Circulation
Open Gears Hand Applied
Reduction Gears (Open) Splash or Circulation Pump
Speed Reducers Splash Circulation
2. Jack-Ups, and Others
Product
1
TS-65 M.P. Moly Grease
TS-65 M.P. Moly Grease1
TS-65 M.P. Moly Grease1
Swab teeth with TS-209 O.G.L.or TS-210
Swab teeth with TS-209 O.G.L.or TS-210
TS-65 M.P. Moly Grease. Use hand gun.
TS-65 M.P. Moly Grease. Use hand gun.
Swab teeth with TS-209 O.G.L.or TS-210
TS-65 M.P. Moly Grease. Use hand gun.
TS-65 M.P. Moly Grease1. Use hand gun.
Check oil level (see note). Add when necessary.
TS-65 M.P. Moly Grease, TS-209, or TS-264 Skidding Grease.
Check oil level (see note). Add when necessary.
orking. Always follow the manufacturers specifications. Where an SAE 90 is required, use TS-313 Moly
F, use TS-302 Moly SAE 140 Gear Oil.
eeded; twice monthly may be often enough.
Barges & Dredges
Product
TS-304 Moly 20/40 Oil 0°F. to 425°F.
TS-203 B&R Cable Lube or TS-210 SeaSafe L.D. & Cable Lb.
TS-70 Moly Paste
TS-304 Moly 20/40 Oil 0°F. to +400°F.
TS-65 M.P. Moly Grease 0°F to +400°F
TS Moly Motor Eze
TS-304 Moly 20/40 Oil 0°F. to 425°F.
TS-804 Chain & Cable Lube
TS-301 Moly 0°F. to 450°F.
TS-65 M.P. Moly Grease 0°F. to 400°F.
TS-801 Dry Film Moly
TS-65 M.P. Moly Grease 0°F. to 400°F.
TS-Blue Lightning
TS-333 Heavy Grind
TS-Moly Motor Eze
TS-304 Moly 20/40 Oil 0°F. to 425°F.
TS-201 Walking Cam or TS-209 O.G.L.
TS-301 Moly Gear Lube 0°F. to 450°F.
TS-304 Moly 20/40 Oil 0°F. to 425°F.