Looking for Roller Blinds in Australia? Perth Blinds manufactures wide choice of custom- made Wired Motorised Roller blind. With us, you find some inspiration for the perfect design for your home or workspace. Our employees are skilled and backed with years of experience in the window coverings field.

1. PLEASE READ THESE INSTRUCTIONS ALL
THE WAY THROUGH BEFORE COMMENCING
INSTALLATION.
INSPECTALLPARTSFORDAMAGEORMISSING
COMPONENTS.
INSTALLATIONWORKANDELECTRICALWIRING
MUST BE DONE BY QUALIFIED PERSON (S) IN
ACCORDANCE WITH ALL APPLICABLE CODES
AND STANDARDS.
GETTING STARTED
© Copyright 2011 Hunter Douglas Limited [ABN 98 009 675 709]
® Registered Trade Marks of Hunter Douglas Limited
TYCO®
is a registered Trade Mark of Tyco International
Services Gmbh.
REF: 2010-26lmccii.indd 18.611.003 03/2011
LUXAFLEX®
MOTORISATION
INSTALLATION & SAFETY
INSTRUCTIONS
IMPORTANT
SINGLE BUTTON SWITCH (ZERO VOLTAGE)
OPTIONAL
3. Assemble Motor Plug (MPU 230) to the end of the 2.5
metre (supplied) motor lead with the TYCO®
Connector
on the other end, according to the supplied install
instructions that come with each Intelligent motor controller.
Then plug assembled motor plug into the Intelligent motor
control.
4. Mount the Intelligent motor control in an available roof/floor
space or electrical cabinet.
IMPORTANT: Never mount Intelligent Motor Controls on or
next to any device that radiates heat or in a damp environment.
Avoid mounting to High powered AC components. Never mount
Intelligent Motor Control so that the motor plug or AC cord is
stretched or causing tension on the box or cord.
5. The Motor controller is supplied with an IEC3 plug. In order
to allow easy isolation of the controller from mains power,
install a GPO at or near the location where the controller
will be located. This will allow the Blind installed to isolate
the power to the motor before connecting the inline
connector between the controller and the blind motor.
6. Insert supplied AC power cord to the RP60ABMH AU240
marked “AC Input”.
If an optional single or double button switch is to be used to
operate the blind as well as the remote control, the switch will
be supplied with the intelligent motor control.
Switches are to be wired into the DRY contact closures included
on the side of the Intelligent Motor Control.
WARNING - NO Voltage or AC power source is required
when the switch is wired to the dry contact closures on the
Intelligent Motor Control.
1. Install the switch at the wall location required.
2. Use any small gauge wire (only 2 wires are required) from
the back of the switch to the COMMON and OPEN contacts
on the Intelligent motor control. There are two sets of dry
contact closures on the DUAL intelligent motors control,
and one set on the SINGLE intelligent motor control.
3. From the back of the switch to be used, run the COMMON/
OPEN from the two contacts indicated on the right.
4. The Intelligent Motor Control is able to interpret a SPST
Maintained switch to open/close and stop the shade. A
single press of the switch will open the shade, a second
press with change the direction of the shade, and two quick
presses of the switch will send a stop to command to the
blind.
Common
Open

2. SAA Approval Number SAA100223, SAA090975,
C-Tick N19673
The Model RP60ABMH AU240 and RP60ABMH2 AU240 Motor
Controls are designed to be used with any standard 240V
bi-directional motor that has built-in travel limits. The motor must
have power, direction 1, direction 2, and ground connection
wires. This system is designed for INTERIOR USE ONLY.
WARNING - Never install this product with power connected.
DISCONNECT FROM POWER SUPPLY before installing or
adding accessories to this device.
WARNING - EVALUATED FOR FIRE AND SHOCK ONLY, NOT
ENTRAPMENT. READTHESEINSTALLATIONINSTRUCTIONS
FOR LISTED APPLICATIONS AND LOCATION.
WARNING - Prior to installation inspect all parts for damage or
missing components.
WARNING - To Reduce the Risk Of Fire, Electric Shock, Or
Injury To Persons, Installation Work And Electrical Wiring
Must Be Done By Qualified Person(s) In Accordance With All
Applicable Codes And Standards.
WARNING - To Reduce the Risk of Fire and Electric Shock,
Install This Controller Only With Listed Window Shade, Projection
Screen or Projector Lift Operator(s) Rated Maximum 2.0 amps
at 240V Each.
WARNING -
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Young children should be supervised to ensure that they do
not play with the appliance.
This Document will outline installation guidelines for installation
of:
• 2-Button Switch Control (240Volt supply and switching)
• Remote Control with Intelligent Motor control (Single or Dual)
• Remote Control with Intelligent Motor control and optional
switch, one button or two button (zero voltage dry contact
switching)
Overview
When the installation package contains a motor tail and 2 button
Clipsal Saturn Series Switch, the blind will be controlled via
simple two button operation.
Button 1 (The lower button) will supply power to the blind motor.
(240V AC).
When the blind motor has power supplied the (optional) LED
light can be wired to illuminate, indicating that power has been
supplied.
Button 2 (the top button) acts as a direction change, and
switches the UP/DOWN wire from the motor.
1. The supplied Flex cable with TYCO®
Plug should be
installed so that the PLUG is located where the blind will be
installed in the window reveal.
2. Depending on the required finish, the diameter of the hole
can be large enough to allow only the Flex cable to be run
through the hole into the roof space, or the hole diameter
can be made large enough to allow the entire TYCO®
Plug
to be pushed back up into the reveal to conceal the plug
completely.
3. The rubber stopper must be left on the end of the exposed
cable and the power isolated until the blind installer has
connected the blind to the system and secured the in-line
connectors together.
WARNING - DO NOT parallel wire motors together. Doing so
will cause damage to the motor.
WARNING - The Inline connector must have power disconnected
before connecting the blind motor. Please observe the safety
warning on the supplied cable.
Overview
When the installation package supplied is for remote control
operation of the motorised blind, the following items will be
supplied:
1 (or more) x intelligent motor control
(single or dual)
1 x IEC3 power cord for Intelligent Motor Control.
(1 per intelligent motor control)
1 x Flex cable tail with TYCO®
Plug
(1 per motorised blind)
1 x RF Receiver
(always connected in the EYE socket of the intelligent motor
control)
1 x RF Remote control
(pre programmed)
OPTIONAL
1. One or Two button switch for optional Dry Contact control of
the blind.
2. 5m, 10m or 20m 4cc BUS cable for linking Intelligent Motor
controls together.
The following diagram illustrates an overview of the connected
system.
It is important to make note of the number that has been
indicated on the Intelligent Motor control.
The number (1, 2, 3 or 4) corresponds to the channel number
on the remote control.
If you are unsure of the controller location, please contact the
local LUXAFLEX®
Dealer.
The controller must be installed and cabled (with the supplied
flex cable and Tyco®
Connector) to the blind that will be
controlled from the channel number indicated on the controller.
Two Button Switch Control Wiring Diagram
Configuration layout for a DUAL intelligent motor control
Configuration layout for 2 x DUAL intelligent motor
controls bussed together.
DESCRIPTION
SAFETY
INSTALLATION
MOTOR WITH TWO BUTTON SWITCH
INTELLIGENT MOTOR CONTROL
(SINGLE OR DUAL)
GUIDELINES FOR CERTIFIED ELECTRICIANS
INSTALLATION
Button 2
Direction
Button 1
Supply Power
Overview
1. Identify the assigned channel number of the intelligent
motor control (indicated with black marker on the side of
the controller).
2. Install supplied Flex cable with TYCO®
Connector at each
window location.