the best service repair manual

1. Original InstructionsCopyright DOOSAN 2014
Serial Number 10001 and Up
Shop Manual
DL300-5/DL350-5
Wheel Loader
950106-01256E
April 2014
DOOSAN and the DOOSAN logo are registered
trademarks of DOOSAN Corporation in the United
States and various other countries around the
world.

2. Table of Contents
Page I
1Table of Contents
1 Safety 1 Wheel Loader Safety
2 Specifications 1 Specifications
3 General Maintenance 1 General Maintenance Instructions
2 Standard Torques
4 Engine 1 Engine
5 Drivetrain 1 Transmission and Torque Converter (4WG)
2 Transmission and Torque Converter (5WG) (Option)
3 Front Axle
4 Rear Axle
5 Driveshaft
6 Steering 1 Power Steering System
2 Steering Unit
3 Steering Pump
4 Flow Amplifier
5 Jerk Softener & Accumulator
7 Brake 1 Service Brake
2 Brake & Pilot Supply Valve
3 Charging Block
4 Parking Brake
5 Brake Pedal Valve
6 Accumulator
7 Brake Filter

3. Table of Contents
Page II
8 Cooling System 1 Cooling System
2 Fan & Brake Pump
3 Fan Motor
4 Fan Control Valve
9 Hydraulic System 1 Main Pump
2 Main Control Valve
3 Pilot System
4 Hydraulic System
5 Hydraulic System Troubleshooting
10 Frame 1 Articulation Center
2 Cabin
3 Counterweight
4 Oil Tank
5 Fuel Tank
6 Cylinders
11 Electrical System 1 Electrical System
2 Air Conditioner
12 Options 1 Emergency Steering
2 Load Isolation System
3 Auto Grease System
13 Schematic 1 Hydraulic Schematic/Electrical Schematic

4. Wheel Loader Safety
1-1-1
DL300-5/DL350-5
Wheel Loader
Safety
Edition 1

5. Wheel Loader Safety
1-1-3
DL300-5/DL350-5
Table of Contents
Wheel Loader Safety
Safety Instructions ..........................................1-1-5
Safety Messages ............................................1-1-5
General...........................................................1-1-7
Operation......................................................1-1-18
Maintenance .................................................1-1-31
Transportation ..............................................1-1-46
Environment and Circumstances..................1-1-48

6. Wheel Loader Safety
1-1-5
DL300-5/DL350-5
SAFETY INSTRUCTIONS
SAFETY MESSAGES
Safety messages and safety decals included in this manual and
on the machine provide instructions how to operate, service and
maintain the machine. Safety messages and safety decals
indicate potential hazards and describe safety precautions
required to avoid hazards. Operator and maintenance personnel
should read and understand these safety messages and decals
before beginning operation or maintenance.
Signal Words
The signal words "DANGER", "WARNING", "CAUTION" are
used throughout safety messages and safety decals in this
manual or on the machine. They indicate an existence of, and
the relative seriousness of, a hazard. All three indicate that a
safety risk is involved. Observe the precautions indicated
whenever a Safety Alert Symbol is present, no matter which
signal word appears next to it.
WARNING
AVOID DEATH OR SERIOUS INJURY
Instructions are necessary before operating or servicing
machine. Read and understand the Operation &
Maintenance Manual and signs (decals) on machine. Follow
warnings and instructions in the manuals when making
repairs, adjustments or servicing. Check for correct
function after adjustments repairs or service. Untrained
operators and failure to follow instructions can cause death
or serious injury.
SAFETY ALERT SYMBOL
Be Prepared - Get to Know All Operating and Safety
Instructions.
This is a Safety Alert Symbol. Wherever it appears in this
manual or on safety decals on the machine, you must be
alert to the potential for personal injury or accidents.
Always observe safety precautions and follow
recommended procedures.

7. DL300-5/DL350-5Wheel Loader Safety
1-1-6
Other Signal Words
In addition to safety signal words, the following signal words are
used to indicate proper and effective use of machine.
NOTE: The word "NOTE" identifies information for effective
use.
1. Turn battery disconnect switch to "ON" position.
2. Close battery compartment door.
DANGER
DANGER - This signal word is used on safety messages and
safety labels and indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING
WARNING - This signal word is used on safety messages and
safety labels and indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION - This signal word is used on safety messages
and safety labels and indicates a potentially hazardous
situation which, if not avoided, could result in minor or
moderate injury.
IMPORTANT
This signal word identifies procedures which must be
followed to avoid damage to machine.

8. 1Engine

9. Engine
4-1-7
DL300-5/DL350-5
SAFETY INSTRUCTIONS
WARNING
AVOID DEATH OR SERIOUS INJURY
Instructions are necessary before operating or servicing
machine. Read and understand the Operation &
Maintenance Manual and signs (decals) on machine. Follow
warnings and instructions in the manuals when making
repairs, adjustments or servicing. Check for correct
function after adjustments repairs or service. Untrained
operators and failure to follow instructions can cause death
or serious injury.

10. DL300-5/DL350-5Engine
4-1-8
OVERVIEW
FRONT
WL1400224
Figure 1

11. Engine
4-1-19
DL300-5/DL350-5
Mounting the Engine in a Universal Stand
Preparations before commencing work:
• Remove engine from the machine.
1. Mount the engine in the universal stand.
1 4
3
2
FG020231
Figure 3
Reference
Number
Description
1 Engine Control Unit
2 Fuel Filter
3
High-pressure Pump and Feed
Pump
4 Starter Motor
Reference
Number
Description
1
2 3
99 331
FG020232
Figure 4
Reference
Number
Description
1 Bolt M10 x 30 (8 off)
2 Nut M16 (4 off)
3 Bolt M16 x 50 (4 off)

12. DL300-5/DL350-5Engine
4-1-20
ENGINE IDENTIFICATION
Engine Data Plate
A
B
C FG020225
Figure 5
Reference
Number
Description
A Smoke Value
B Engine Type
C Engine Serial Number
Figure 6
2
1
4
5
6
7
3
Figure 7
Reference
Number
Description
1 Warning! Only for Lifting Engines
2
Warning! Draining the Fuel Housing.
Warning! High Fuel Pressure
3 Engine Power
4 Important! Warranty Registration
5 Valve Clearance
6 Assistance
7 Information on Emissions

13. Engine
4-1-21
DL300-5/DL350-5
ENGINE SPECIFICATION
Items Specification
Engine
Type
4-Cycle Water Cooled, Waste Gate
Turbocharge, Air to Air Intercooled Direct
Injection
Emission US EPA Tier 4 Final (EU Stage IV)
Model DC 9
Injection System Extra High-pressure Fuel Injection System
Rated Net Power 202 kW (271 HP) @ 1,800 rpm (SAE J1995)
Valve Clearance
Intake Valve 0.45 mm
Exhaust valve 0.70 mm
Number of Cylinders and Configuration 5, Straight
Rotating Direction (from Flywheel) Counterclockwise
Oil Pressure
Normal with the Engine at
Operating Temperature,
Operating Speed
3.1 - 6.1 kg/cm2 (3 - 6 bar, 43.5 - 87 psi)
Min. Permitted at Idling
Speed
0.71 kg/cm2 (0.7 bar, 10.2 psi)
Crankcase Pressure with Closed
Crankcase Ventilation
-5.4 - 2.0 bar
Using Lubrication Oil
ACEA-E5 or E7
(for Fuel with Ultra Low Sulfur Content)
Oil Filter Paper Filter
Interval Between Oil Changes 500 h
Working Principle 4 Stoke Engine
Cylinder Diameter 130 mm
Piston Stroke 140 mm
Displacement 9,300 cc
Compression Ratio 17:1
Number of Teeth on the Flywheel 158
Low Idle Speed 600 - 750 rpm
Max. Full Load Speed 2,100 rpm
Weight, without Coolant and Oil 1,035 kg
Cooling System
Volume,
Excluding Radiator
16,000 cc
Coolant Temperature 90 - 95°C
Number of Thermostats 1
Thermostat,
Opening Temperature
80°C
Electrical System Type 1-pin, 24V, DC
Starter Motor
(Standard Equipment)
1-pin, 24V, 6 kW
Alternator
(Standard Equipment)
1-pin, 28V, 100 A

14. DL300-5/DL350-5Engine
4-1-30
Tightening Torques for Engines
IMPORTANT
Tightening torques for threaded joints in engines.
If the tightening torque is not available in the table for each
engine, refer to the special and normal tightening torques
tables.
Engine Assembly
Cylinder Block
• Piston cooling nozzle: 23 Nm
Main Bearing Cap
NOTE: The screws can only be reused 3 times. Mark the
screws each time before installing.
• Torx screw (M19): 110 Nm + 90°
• Hexagon screw (M19): 110 Nm + 90°
Connecting Rod Cap
NOTE: The screws can only be reused 3 times. Mark the
screws each time before installing.
1 2 3 4
EX1301810
EX1301811
1 2 3 4
EX1301810

15. Engine
4-1-31
DL300-5/DL350-5
• Torx screw: 50 Nm + 90°
• Check torque: 170 Nm
Flywheel Housing
• Lead-in union: 40 Nm ±6
Cylinder Head and Valve Package
Cylinder Head
NOTE: The screws can only be reused 3 times. Mark the
screws each time before fitting.
Cylinder head bolt, tightened in four stages
• First stage: 60 Nm
• Second stage: 150 Nm
• Third stage: 250 Nm
• Fourth stage: 90°
EX1302070
1 2 3 4
EX1301810
1
2
3
4
5
6
FG020253

16. DL300-5/DL350-5Engine
4-1-32
Rocker Cover
• Rocker cover, upper: 18 Nm
• Rocker cover, lower: 18 Nm
Valve Mechanism
• Adjusting screw nut on rocker arm: 35 Nm

17. Engine
4-1-33
DL300-5/DL350-5
• Screw for rocker arm shaft bearing retainer:
90 Nm + 60°
Roller Tappet Shaft
• Banjo screw for roller tappet shaft (engines produced
earlier): 33 Nm
• Slotted screw for roller tappet shaft (engines produced
later): 40 Nm

18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. DL300-5/DL350-5Engine
4-1-34
Crank Mechanism
Flywheel
• M18 flange screw: 180 Nm + 120°
Torsion Damper
• Torsion damper hub: 90 Nm + 30°
Timing Gear
• Intermediate gear: 50 Nm + 60°
• Camshaft gear: 20 Nm + 40°
Lubrication System
Oil sump
• Cylinder block, 8.8 screw: 26 Nm
• Cylinder block, 10.9 screw: 32 Nm
• Against cylinder block, 8.8 screw with spacer: 26 Nm
Oil Sump, Plastic
• Oil sump, spring screw: 20 Nm
EX1301830

20. Engine
4-1-35
DL300-5/DL350-5
Oil Plug
• Thread insert for oil plug: 320 Nm
• Magnetic oil plug, oiled seal: 80 Nm
• Magnetic oil plug, dry seal: 115 Nm
• Oil plug for filler connection in oil sump: 60 Nm
• Oil pump, 10.9 screw: 32 Nm
• Oil pump, 8.8 screw: 26 Nm
• Hose connection for cooling system: 85 Nm
• Oil fill pipe, retaining screw: 20 Nm
Oil Filter
• Element type filter, cover: 25 Nm
• Oil filter unit without loose filter: Hand tighten

21. DL300-5/DL350-5Engine
4-1-36
Oil Cooler
• Oil cooler core: 26 Nm
Centrifugal Oil Cleaner
• Nut for outer cover: 15 Nm
Oil Mist Separator
• Nut (M18 x 1.5): 35 ±5 Nm
Exhaust System
Exhaust Manifold
• Cylinder head hexagon screw: 40 Nm + 60°
• Cylinder head Torx screw: 60 Nm + 60°
• Turbocharger: 50 Nm
Exhaust pipe from Turbocharger
• Turbocharger (V-clamp): 20 Nm
Turbocharger Oil Pipe
• Turbocharger lubrication pipe: 40 ±1.2 Nm (±3 %)
• Nut for turbocharger lubrication pipe: 35 ±5 Nm
Turbocharger Coolant Pipe
• Water inlet, turbocharger: 40 Nm
• Water inlet, variable geometry turbocharger electric motor: 10 Nm
EX1301840