1. To, 1ST
December 2023
RANGERS
BADIN
ATTN MR. SHARAFAT
Subject: OGO BrandReverse Osmosis Plant 5000 GPD under 3000 TDS
Dear Sir,
Reference your sales enquiry for reverse osmosis system 5,000 GPD Capacity.
We are pleased to quote for the same as follows the proposal or R.O based on
your water provided water analysis 3000 TDS.
1.0 Multimedia/ Sand Filter & Carbon Filter 02 Set.
To remove the total suspended solids, dirt, iron and reduce silt and to provide TSS free water
1.1 Vessel
a. Make: European
b. MOC: MS/FRP Lined
c. Diameter: 16 inch
d. Height: 65 inch
e. Piping UPVC/ Hydro seal/Canada
f. Valve 1”
g. Sand Filter or Carbon Filter =02 Sets
1.2 Media
Mixed bed sand media Filter.
a. Gravel 300mm
b. Quartz Sand 600mm
c. Total Bed depth: 900 mm
d. Working Pressure: 03~05 bars
e. Test pressure: 07 bars
f. Activated Carbon (China)
2.0 RO Feed Pump 01 Set
a. Material; Stainless steel
b. Manufacturer: CNP BRAND NEW CHINIA.
c. 3 Phase/50Htz
d Position Horizontal.
3.0 Chemical Injections SYSTEM
For dosing System Antiscalant.
2. 3.1 Dosing Pump 02 Nos.
a. MOC: PP
b. Capacity: 5 LPH,
c. Pressure: 5 Bar
d. Make: New Etatron, Italy/Equivalent
3.2 Dosing tank 02 Nos.
a. Capacity: 80 liters
b. MOC: HDPE
c. Make: Super Tuff (Pakistan)
4.0 PVC CARTRIDGE FILTER Housing / MICRON FILTER 01 No.
To remove the fine particles up to 05 microns and reduce silt density index levels to acceptable level.
4.1PVC Cartridge Filter Housing 02No.
a. Size 20”-05.
b. MOC UPVC/SS
c. In & Out Size 1”
d. Threaded
e. Flow Rate 100 GPM
f. Make European/Equivalent
4.2 Cartridge
a. Filters Size 4”X 20”
b. Qty of Filters 02 Nos.
c. MOC PPF
d. Micron Rating 05 micron Nominal.
5.0 HIGH PRESSURE PUMP 01No. .
Heavy-duty corrosion resistant with heavy –duty industrial motor
(Totally enclosed air cooled)
h. Type Multistage Centrifugal
i. Material Stainless steel
j. Manufacturer cnp brand new china.
3 Phase/50Htz
m. Position Vertical
n. Electrical 220 V, 1 phase, 50 Hz
6.0 RO MEMBRANE 01 No’s
To remove the majorpart of TDS 95% up to 98% by Reverse Osmosis Membranes arranged and designed to give
adequate flow and recovery.
a. Type: Spiral Wounded
b. Diameter of Membrane: 8.0 inch each
c. Length of Membranes: 40 inch each
d. Salt Rejection: 95-98%
e. Make: USA.
3. 7.0 RO PRESSURE VESSELS 01 No’s 8X40
To pack Reverse Osmosis Membranes and operate at high pressure up to 300 psi reverse osmosis
pressure vessel housings are made of fiberglass tested and certified by the American Society of
Mechanical Engineers (ASME) and the boiler association of the USA, End cap retainers are aluminum alloy
& Enamel coated white.
a. MOC FRP Composite
b. Make ROPV/Equivalent
c. Position Horizontal, Series
d. Type Side Port/1 Element
8.0 MEMBRANE CLEANING SYSTEMS (CIP)
We provide a flushing system, which shall help to clean the membrane & get rid of the flatulent that get
deposited on the membranes.
9.0 ELECTRICAL PANEL
b. Microprocessor RO Controller (Create)
c. Control & Safety voltage 24 volts DC.
e. Motor operate through, Magnetic Contactor, Over Load Relay Phase Falier Relay.
f. On/Off push button & Indication light & Tripping light & Safety Alarm.
g. with auto manual switch.
h. with auto level controller switch
i. With Analog Amp/Volt meter.
j. Body material MS oven baked painted
k. Control Auto & Manual
10. INSTRUMENTS
10.1 Flow Meter: 02 Nos.
a. Type Rota Glass
b. Material Acrylic
c. Make Zyia
d. size 10-20 GPM
11. Quality meter 01No.
a. Type Digital/Panel mounted.
b. Make Create/Eq
12. Pressure Gauges 04 Nos.
a. Make Wikal/ Equivalent
b. Filled Liquid
c. Dial size 2.5”
4. 13= Pressure Switches 02 No.
a. High-Pressure switch SS Bellow SIKO/ Equivalent
b. Low Pressure Switch SS Bellow SIKO/ Equivalent
14. Piping
a. High Pressure 80 Sch. UPVC, Hydro seal, (Canada/Eq)
b. Low Pressure 80 Sch. UPVC, Hydro seal, (Canada/Eq)
15. Valves
a. High Pressure UPVC Hydro seal, 80 Sch. Canada/Eq.)
b. Low Pressure UPVC Hydro seal, 80 Sch. Canada/Eq.)
16. System Skid
This system is fully mounted on heavy-duty Mild steel box pipe.
Deco painted with iron protective under coat.
17. Sample permeates ports: 01
Sample permeate ports will be installed for each reverse osmosis
Pressure vessel to allow evaluation of membrane function and permeate.
Manufacturer: Hydro seal (Canada)
Size: ½”
Material: UPVC
Type: ball valve
18. Totaling hour meter: 01
Will keep count of total hours the plant is in operation.
Panel mounted and high quality
Qty One
Manufacturer: Panasonic
Size 45mm x 45 mm
Type panel mounted
19. High pressure Regulator Concentrate valve:
Heavy-duty high pressure regulator valve can be adjusted to maintain the desired high pressures out
Of the high pressure pump. And into the reverse osmosis membrane:
Qty One
Material SS Dia. 1”
Specification: Heavy duty pressure
Valve up to 300 to 316 PSI
20. Tagging and Labels:
All components and sub-assemblies will be tagged and
Numbered accordingly, for easy of operation and identification.
5. 21. Testing and quality assurance:
The equipment is fully factory tested and sterilized
For a period of one week.
22. Reverse Osmosis System
R/O shipping weight 4000 KGS approx
Min. Inlet Pressure 3~5 Bar
Feed Water TDS Less than 7000PPM
Feed water type 20 ºC ~ 27 ºC
Product water quality 95 to 98% Rejection
Permeate Water Recovery 45 ~ 55 %
Permeate pH 6.5 ~ 8
24. Ultra Violet System 33”
a. Uv Lamp 33” : 1 No
b. Radiation Chamber : SS316
c. Brand Name : Philips
d. Complete Box : 01 No
26. Boosting Pump 01 Set
a. Material; Stainless steel
b. Manufacturer: Grund Foss Refurnished.
c. 3 Phase/50Htz
d Position Vertical.
e. Electrical: 380/440 V, 3 phase, 50 Hz
27. Absolute Cartridge Filter Housing 02 No.
a. Size 20” Slim
b. MOC UPVC/SS
c. In & Out Size 1”
d. Threaded
e. Flow Rate 20 GPM
f. Make European/Equivalent
27.1 Cartridge
a. Filters Size 2.5”X 20”
b. Qty of Filters 02 Nos.
c. MOC PPF
d. Micron Rating 05 micron Nominal.
6. 26. Terms & Conditions
Buyers Responsibility
i. To provide electric power into the plant room.
ii. To provide drain line near plant room.
iii. To provide feed line near plant room.
iv. All civil work.
v. Site clearance.
Rs.10,75,000 WITHOUT INSTALLATON AND
TRANSPOTATION KARACHI TO BADIN.
Delivery : 10 days After Receiving Advance Payment.
Payment : 100% Advance
If you have any queries please do not hesitate to contact us.
Thanks and best regards
IRFAN AZAM
DIRECTOR
03002734871
OUR NEW ADDRESS. OUTLET NO.1. BUILDING 13-C, 15TH COMMERCIAL STREET PHASE 2
EXTENSION D.H.A KARACHI NEAR KAMAL MOTORS AND HAFIZ AYAZ MASJID
03111646666(MR YASIR)
SEE PLANT PICTURE BELOW