This document provides the disassembly and assembly procedures for a travel motor on a 336D LN excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and bearings. The 28 steps for assembly install these components in reverse order and include notes about cleaning parts, applying thread lock compound and oil, and ensuring parts are returned to their original positions. Tools required include an adapter, nuts, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...cdfxssw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of marked components. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...cdfxssw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...cdsasw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...fhsjekdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...fjskekdmjekm
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...fhsjekdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...fjskekdmjekm
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for the procedures are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...cdsasw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...cdfxssw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of marked components. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...cdfxssw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...cdsasw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...fhsjekdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...fjskekdmjekm
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...fhsjekdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d l excavator (prefix pgw) service repair manual (pgw0000...fjskekdmjekm
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for the procedures are also listed.
Caterpillar cat 336 d excavator (prefix pgw) service repair manual (pgw00001 ...cdsasw
This document provides the disassembly and assembly procedures for a travel motor on excavator models 336D and 336D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that were marked during disassembly. Tools required for disassembly and assembly are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...fjsekkdmeik
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...fjsekdmmeed
This document provides the disassembly and assembly procedures for a 325D L excavator travel motor. Key steps include:
1. Removing the travel motor and marking components for reassembly.
2. Dismantling internal components like the head, plates, seals, springs, and bearing races.
3. Cleaning all parts thoroughly before inspection and assembly.
4. Reassembling components in reverse order, taking care to return parts to their original positions and applying thread lock compound as needed. Proper tooling is required for pressing and installing retaining rings.
Caterpillar cat 324 d l excavator (prefix jzr) service repair manual (jzr0000...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 324 d excavator (prefix jzr) service repair manual (jzr00001 ...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsejdkemmn
This document provides the disassembly procedure for a 325D L excavator travel motor. Key steps include:
1. Removing the travel motor and cleaning/marking components for reassembly.
2. Disassembling the travel motor housing and removing internal components like seals, springs, plates, and shafts.
3. Cleaning all parts thoroughly before reassembly and reinstalling components in reverse order, taking care to align marks and apply threadlocker as needed.
Caterpillar cat 324 d excavator (prefix tsn) service repair manual (tsn00001 ...fjskekazswdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper tooling and torque specifications are listed for selected assembly steps.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
More Related Content
Similar to Caterpillar Cat 336D LN Excavator (Prefix MYP) Service Repair Manual (MYP00001 and up).pdf
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...fjsekkdmeik
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...fjsekdmmeed
This document provides the disassembly and assembly procedures for a 325D L excavator travel motor. Key steps include:
1. Removing the travel motor and marking components for reassembly.
2. Dismantling internal components like the head, plates, seals, springs, and bearing races.
3. Cleaning all parts thoroughly before inspection and assembly.
4. Reassembling components in reverse order, taking care to return parts to their original positions and applying thread lock compound as needed. Proper tooling is required for pressing and installing retaining rings.
Caterpillar cat 324 d l excavator (prefix jzr) service repair manual (jzr0000...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 324 d excavator (prefix jzr) service repair manual (jzr00001 ...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsejdkemmn
This document provides the disassembly procedure for a 325D L excavator travel motor. Key steps include:
1. Removing the travel motor and cleaning/marking components for reassembly.
2. Disassembling the travel motor housing and removing internal components like seals, springs, plates, and shafts.
3. Cleaning all parts thoroughly before reassembly and reinstalling components in reverse order, taking care to align marks and apply threadlocker as needed.
Caterpillar cat 324 d excavator (prefix tsn) service repair manual (tsn00001 ...fjskekazswdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper tooling and torque specifications are listed for selected assembly steps.
Similar to Caterpillar Cat 336D LN Excavator (Prefix MYP) Service Repair Manual (MYP00001 and up).pdf (7)
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
3/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
4/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
Illustration 4 g00887331
5/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
6/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
7/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
8/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
9/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
10/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
11/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
12/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYP
Configuration: 336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
S/N - B6H1-UP
S/N - DTS1-UP
S/N - EAH1-UP
S/N - EDX1-UP
S/N - EFT1-UP
S/N - ERN1-UP
S/N - FAR1-UP
S/N - FFK1-UP
S/N - GGE1-UP
S/N - GGH1-UP
S/N - HAS1-UP
S/N - HHK1-UP
S/N - J2F1-UP
S/N - JBT1-UP
S/N - JLP1-UP
S/N - JTN1-UP
1/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. S/N - WRK1-UP
S/N - XBH1-UP
S/N - YCF1-UP
S/N - ZCT1-UP
S/N - ZML1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
3/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
4/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
5/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
6/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
7/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
8/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
Illustration 15 g00887501
9/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
10/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
11/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
12/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 00:40:54 UTC+0800 2020
13/13
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 E...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYP
Configuration: 336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00878123
2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
336D L & 336D LN Excavator MYP00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...