This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly instructions for a 980H wheel loader torque converter in 3 sentences:
It outlines 56 steps to disassemble the individual components of the torque converter like removing bolts, gears, bearings, seals, and other parts using various tools like push-pullers, bearing pullers, and presses. The purpose is to take the torque converter fully apart in order to service or replace components like bearings, seals, and other wear items. Detailed illustrations accompany each step to show how to remove each part from the torque converter.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting the importance of cleanliness and applying oil to bearings during assembly. Required tools are listed for specific disassembly and assembly steps.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a freewheel stator in the torque converter of a 980H wheel loader. It lists over 50 steps and required tools to disassemble all components of the torque converter. These include removing housing assemblies, gears, seals, bearings, and other internal parts. The assembly section provides the reverse steps and notes on cleanliness and lubrication to reassemble the torque converter.
This document provides disassembly instructions for a 980H wheel loader torque converter in 3 sentences:
It outlines 56 steps to disassemble the individual components of the torque converter like removing bolts, gears, bearings, seals, and other parts using various tools like push-pullers, bearing pullers, and presses. The purpose is to take the torque converter fully apart in order to service or replace components like bearings, seals, and other wear items. Detailed illustrations accompany each step to show how to remove each part from the torque converter.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting the importance of cleanliness during assembly. Required tools are listed for each step.
This document provides disassembly instructions for a 980H wheel loader torque converter in 3 sentences:
It outlines 56 steps to disassemble the individual components of the torque converter like removing bolts, gears, bearings, seals, and other parts using various tools like push-pullers, bearing pullers, and presses. The purpose is to take the torque converter fully apart in order to service or replace components like bearings, seals, and other wear items. Detailed illustrations accompany each step to show how to remove each part from the torque converter.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting the importance of cleanliness and applying oil to bearings during assembly. Required tools are listed for specific disassembly and assembly steps.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a freewheel stator in the torque converter of a 980H wheel loader. It lists over 50 steps and required tools to disassemble all components of the torque converter. These include removing housing assemblies, gears, seals, bearings, and other internal parts. The assembly section provides the reverse steps and notes on cleanliness and lubrication to reassemble the torque converter.
This document provides disassembly instructions for a 980H wheel loader torque converter in 3 sentences:
It outlines 56 steps to disassemble the individual components of the torque converter like removing bolts, gears, bearings, seals, and other parts using various tools like push-pullers, bearing pullers, and presses. The purpose is to take the torque converter fully apart in order to service or replace components like bearings, seals, and other wear items. Detailed illustrations accompany each step to show how to remove each part from the torque converter.
This document provides instructions for disassembling and assembling the freewheel stator component of a 980H wheel loader torque converter. It lists over 50 individual steps to remove parts like bearings, gears, seals, and housings. Tools required include various pullers, drivers, and pins. Cleanliness is emphasized during assembly, with parts cleaned and oiled before being pressed or installed in the specified order.
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting the importance of cleanliness during assembly. Required tools are listed for each step.
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting that cleanliness and applying oil to bearings is important. Required tools are listed for specific removal and installation steps.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader. The disassembly section describes 55 steps to fully disassemble the torque converter into individual components. These include removing bolts, gears, seals, bearings and other parts. The assembly section then describes 11 steps to reassemble components such as installing bearings, seals, gears and housing pieces using various tools.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader model 9CM powered by a 3406C engine. It describes 55 steps to disassemble the torque converter and its components like gears, bearings, seals, housing, and provides diagrams. It also describes required tools and cleaning/inspection instructions for reassembly.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 17 tools required. The assembly procedure lists the same tools and provides instructions to reassemble the components in reverse order.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, providing illustrations and required tools for each step.
3. The components include housing, gears, seals, bearings, plates, disks, and an impeller that must be carefully disassembled and reassembled.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It includes 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. The assembly section includes 52 steps to install these components in reverse order, noting orientation and torque specifications. Tools required include link brackets, push-pullers, driver groups and retaining ring pliers.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble the various components of the torque converter using specialized tools. These include removing housing assemblies, gears, seals, bearings and other parts. The assembly process is described in reverse order over multiple illustrations with notes on orientation of specific parts. Special tools are listed that are required for tasks like removing races and bearings.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It lists 46 steps to disassemble the various components of the torque converter using various tools. These components include housing, gears, bearings, seals, plates, and more. The assembly procedure is then described in reverse order over multiple illustrations.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...jmgj942263
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and disassembling and assembling pistons and connecting rods on a Caterpillar 3056E engine. The procedures include using various tools to remove components like piston cooling jets, piston rings, retaining rings, and pins. Detailed steps are provided for cleaning, lubricating, and correctly installing each part in the proper sequence. Safety notices are included to keep parts clean and contain fluids.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists 57 steps to fully disassemble the torque converter and its components. The steps include removing pumps, gears, seals, housings, and other internal parts. Special tools are required for separating some components. Precautions are given to handle parts carefully due to their weights ranging from 25 to 680 kg. Cleanliness is stressed to prevent contaminating precision parts during disassembly.
More Related Content
Similar to Caterpillar Cat 980H Wheel Loader (Prefix MHG) Service Repair Manual (MHG00001 and up).pdf
This document provides disassembly and assembly instructions for a 980H wheel loader torque converter. It includes 56 steps to disassemble the various components of the torque converter such as removing bearings, gears, seals, and housings. The assembly section provides instructions to reassemble the components in the reverse order, noting that cleanliness and applying oil to bearings is important. Required tools are listed for specific removal and installation steps.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader. The disassembly section describes 55 steps to fully disassemble the torque converter into individual components. These include removing bolts, gears, seals, bearings and other parts. The assembly section then describes 11 steps to reassemble components such as installing bearings, seals, gears and housing pieces using various tools.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader model 9CM powered by a 3406C engine. It describes 55 steps to disassemble the torque converter and its components like gears, bearings, seals, housing, and provides diagrams. It also describes required tools and cleaning/inspection instructions for reassembly.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 17 tools required. The assembly procedure lists the same tools and provides instructions to reassemble the components in reverse order.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, providing illustrations and required tools for each step.
3. The components include housing, gears, seals, bearings, plates, disks, and an impeller that must be carefully disassembled and reassembled.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It includes 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. The assembly section includes 52 steps to install these components in reverse order, noting orientation and torque specifications. Tools required include link brackets, push-pullers, driver groups and retaining ring pliers.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble the various components of the torque converter using specialized tools. These include removing housing assemblies, gears, seals, bearings and other parts. The assembly process is described in reverse order over multiple illustrations with notes on orientation of specific parts. Special tools are listed that are required for tasks like removing races and bearings.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It lists 46 steps to disassemble the various components of the torque converter using various tools. These components include housing, gears, bearings, seals, plates, and more. The assembly procedure is then described in reverse order over multiple illustrations.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
Similar to Caterpillar Cat 980H Wheel Loader (Prefix MHG) Service Repair Manual (MHG00001 and up).pdf (20)
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...jmgj942263
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and disassembling and assembling pistons and connecting rods on a Caterpillar 3056E engine. The procedures include using various tools to remove components like piston cooling jets, piston rings, retaining rings, and pins. Detailed steps are provided for cleaning, lubricating, and correctly installing each part in the proper sequence. Safety notices are included to keep parts clean and contain fluids.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists 57 steps to fully disassemble the torque converter and its components. The steps include removing pumps, gears, seals, housings, and other internal parts. Special tools are required for separating some components. Precautions are given to handle parts carefully due to their weights ranging from 25 to 680 kg. Cleanliness is stressed to prevent contaminating precision parts during disassembly.
This service repair manual provides instructions for disassembling and assembling the torque converter of a 992K Wheel Loader. It lists over 60 steps to remove components such as the torque converter, transmission pump, gears, housing, and more. Detailed illustrations accompany each step to show how to position parts and what tools are required. The document provides specifications to safely handle heavy components weighing up to 2850 pounds during the repair process.
This document provides instructions for removing and installing the front gear group on a Caterpillar 3412E engine. It describes:
1. Aligning timing marks and removing the idler gear, bearing, thrust washer, and shaft.
2. Cleaning and installing the shaft, washer, bearing, and idler gear while aligning timing marks.
3. The procedure is accompanied by illustrations and notes on required tools.
This service repair manual provides instructions for assembling the torque converter for a 988K wheel loader. It outlines 92 steps to install various components like seals, bearings, gears, and housing parts. Precision and cleanliness are important during assembly. Tools are required to measure clearances and set components. The manual includes illustrations pointing to each part mentioned in the assembly process.
This document provides instructions for assembling and disassembling parts of a 982M wheel loader transmission. It describes 51 steps to assemble the torque converter. It then describes 5 steps to separate the transmission from the output transfer gears, including using lifting equipment to position components and removing bolts, harnesses, and tubes. The document includes illustrations and lists required tools for each procedure.
This document provides disassembly and assembly instructions for the lock up clutch with freewheel stator on a 980K wheel loader power train. It includes 46 steps to disassemble components such as the torque converter housing, pump adapter, idler gear, shaft assembly, impeller, and stator. It also includes 18 steps for assembly, including installing seals, bearings, plates, rings, and other components in the reverse order of disassembly. Required tools including link brackets, driver groups, and retaining ring pliers are listed. Cleanliness during assembly is emphasized.
This document provides instructions for disassembling and assembling a torque converter for a 972H wheel loader. The disassembly procedure involves removing over 30 individual parts from the torque converter housing in a specific sequence. The assembly procedure instructs technicians to thoroughly clean all parts and install components in the reverse order of disassembly while following torque specifications. Special care must be taken when handling internal components such as bearings and seals.
This document provides instructions for disassembling and assembling the torque converter and its components for a 972H Wheel Loader. It begins with required tools and safety notices. The disassembly steps include removing the torque converter housing, impeller, stator, carrier shaft, and other internal parts. The assembly section instructs installing the components in reverse order and notes that cleanliness is important. Torque specifications and the use of new replacement parts for any that are worn or damaged are also specified.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER MHG
Configuration: 980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i05903287
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B
8B-7548 Push-Puller 1
8B-7550 Leg 2
8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
C
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
D
5F-7343 Bearing Puller Attachment 1
1P-0520 Driver Group 1
E 1P-0510 Driver Group 1
F 7
1/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Forcing Screw
3/8 - 16 x 3 in
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate" for the machine that is being serviced.
1. Place the torque converter housing assembly (2) on wood blocks.
Illustration 1 g00503225
2. Remove bolts (1) and the washers from torque converter housing assembly (2) .
Illustration 2 g01111329
3. Install Tooling (A) to torque converter housing assembly (2) , as shown. Attach a suitable
lifting device to Tooling (A) . The weight of housing assembly (2) is approximately 120 kg
(265 lb).
4. Use Tooling (F) to loosen housing assembly (2) from the torque converter.
2/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove housing assembly (2) from the torque converter.
Illustration 3 g00871317
6. Remove O-ring seal (3) from torque converter housing assembly (2) .
Illustration 4 g00871318
7. Remove bolts (4) and the washers from pump adapter (5) and torque converter housing
assembly (2) .
3/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00871264
8. Use Tooling (F) to remove pump adapter (5) from torque converter housing assembly (2) .
Illustration 6 g00871319
9. Use tooling (C) to remove bearing cup (6) , O-ring seal (8) , and shims (7) from pump
adapter (5) . See illustration 13 for Tooling (C) .
Illustration 7 g00871326
4/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 10. Remove pump drive gear (9) from torque converter housing assembly (2) .
Illustration 8 g00871451
11. Use Tooling (B) to remove bearing cones (10) from each side to pump drive gear (9) .
Illustration 9 g00871333
12. Use Tooling (C) to remove bearing cup (11) from torque converter housing assembly (2) .
See illustration 13 for Tooling (C) .
5/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 10 g01112900
13. Remove bolt (12) and the washer from torque converter housing assembly (2) .
14. Use Tooling (F) to push shaft assembly (14) out of torque converter housing assembly (2) .
15. Remove idler gear (13) from torque converter housing assembly (2) .
Illustration 11 g01112903
16. Remove O-ring seal (15) from shaft assembly (14) .
6/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 12 g00871365
17. Remove bearing cone (16) , bearing cone spacer (17) , and bearing cone (18) from idler gear
(13) .
Illustration 13 g00871366
18. Use Tooling (C) to remove bearing cup (19) from idler gear (13) .
Illustration 14 g00871367
19. Remove bearing cup spacer (20) from idler gear (13) .
7/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 15 g00871368
20. Remove retaining ring (21) from idler gear (13) .
Illustration 16 g00871369
21. Use Tooling (C) to remove bearing cups (22) from idler gear (13) .
8/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 17 g00871370
22. Remove studs (23) from torque converter housing assembly (2) .
Illustration 18 g00871267
23. Remove retaining ring (24) and bearing carrier (25) from the carrier assembly.
Illustration 19 g01112906
24. Remove bearing carrier (25) .
9/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 20 g00871269
25. Remove O-ring seal (26) from bearing carrier (25) .
26. Remove seal ring (27) from ring carrier (28) .
Illustration 21 g00871273
27. Use Tooling (D) and a press to remove ring carrier (28) from bearing carrier (25) .
10/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 22 g00871274
28. Remove retaining ring (29) from bearing carrier (25) .
Illustration 23 g00871275
29. Use Tooling (D) and a press to remove inner bearing (30) from bearing carrier (25) .
Illustration 24 g01112907
30. Remove bolts (31) and the washers from drive gear (32) .
31. Remove drive gear (32) .
11/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 25 g01112910
32. Use Tooling (E) and a press to remove the outer bearing race (32A) (not shown) from drive
gear (32) .
Illustration 26 g00871278
33. Remove retaining ring (33) from drive gear (32) .
Illustration 27 g00871279
12/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 34. Remove bolts (34) and the washers from drive flange (35) and rotating housing (36) .
Illustration 28 g00871281
35. Use bolts (34) as forcing screws to remove drive flange (35) from rotating housing (36) .
The weight of drive flange (35) is 23 kg (51 lb).
Illustration 29 g00871282
36. Remove bolts (37) from drive flange (35) .
13/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 30 g00871283
37. Remove drive flange (35) from impeller (38) .
Illustration 31 g00871284
38. Position impeller hub (39) on wood blocks.
39. Remove impeller (38) from impeller hub (39) .
Illustration 32 g00870210
14/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 40. Remove thrust bearing (40) and race (40A) (not shown) from carrier assembly (41) .
Illustration 33 g00870211
41. Remove carrier assembly (41) and stator (42) as a unit from rotating housing (36) .
Illustration 34 g00870212
42. Remove snap ring (43) from stator (42) . Remove plate (44) from stator (42) .
15/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 35 g01112913
43. Remove 11 freewheel rollers (45) and 11 freewheel springs (46) from freewheel cam (47) .
Remove stator (42) from carrier assembly (41) .
Illustration 36 g01112915
44. Remove retaining ring (48) . Remove plate (49) .
45. Use Tooling (E) and a hydraulic press in order to remove freewheel cam (47) from stator
(42) .
Note: If necessary, heat the stator to a maximum temperature of 135 °C (275 °F) for
approximately 15 minutes.
Illustration 37 g01112917
46. Remove thrust bearing (50) from carrier assembly (41) . Remove sleeve bearing (51) from
carrier assembly (41) .
16/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 38 g01112919
47. Remove thrust bearing race (52) and the thrust bearing.
Illustration 39 g00870286
48. Remove turbine (53) and turbine hub (54) as a unit from rotating housing (36) .
Illustration 40 g01112920
49. Remove bolts (55) and the washers that hold turbine (53) to hub (54) .
17/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 41 g00870755
50. Remove hub (54) from turbine (53) .
Illustration 42 g00870288
51. Remove retaining ring (56) from turbine hub (54) .
18/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 43 g01112924
52. Remove two races (57) and thrust bearing (58) .
Illustration 44 g00870291
53. Remove bolts (59) and the washers from cover assembly (60) .
54. Remove cover assembly (60) from rotating housing (36) .
55. Remove ring seal (61) from rotating housing (36) .
Illustration 45 g00870294
56. Remove sleeve bearing (62) from cover assembly (60) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 22 10:17:08 UTC+0800 2021
19/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER MHG
Configuration: 980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i05903427
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
G
8T-5096 Dial Indicator Test Group 1
5P-2390 Gauge Tool Group 1
H 1P-0520 Driver Group 1
J -
Guide Pin
(3/8 - 16 by 8 in)
2
K -
Guide Pin
(1/2 - 13 by 3 in)
3
L 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, thoroughly cleaned in cleaning fluid.
Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement.
Note: Apply oil to all of the bearings before assembly.
1/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01112937
1. Use Tooling (H) to install sleeve bearing (62) in cover assembly (60) . Sleeve bearing (62)
must be even with the outside surface of cover assembly (60) .
Illustration 2 g03337064
2. Install ring seal (61) to rotating housing (36) .
3. Install cover assembly (60) to rotating housing (36) .
4. Install bolts (59) and the washers to cover assembly (60) . Tighten the bolts to a torque of 30
± 5 N·m (22 ± 4 lb ft).
2/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00870744
5. Install races (57) and thrust bearing (58) to cover assembly (60) .
Illustration 4 g00870748
6. Install retaining ring (56) in turbine hub (54) .
Illustration 5 g00870755
7. Install turbine (53) on hub (54) .
3/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 6 g00870757
8. Install bolts (55) and the washers to turbine (53) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 7 g00870759
9. Install hub (54) and turbine (53) as a unit to rotating housing (36) .
4/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 8 g00870760
10. Install thrust bearing race (52) and the bearing to the turbine hub (54) .
Illustration 9 g01112941
11. Use Tooling (H) and a hydraulic press in order to install sleeve bearing (51) to carrier
assembly (41) . Install thrust bearing (50) to carrier assembly (41) .
Illustration 10 g01112915
5/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 11 g01112913
12. Use Tooling (H) and a hydraulic press in order to install freewheel cam (47) to stator (42) .
13. Install plate (49) to stator (42) . Install retaining ring (48) to stator (42) .
Note: If necessary, heat stator (42) to a maximum temperature of 135 °C (275 °F). Install
the cam with the IMPELLER SIDE facing downward. Continue with the installation until
freewheel cam (47) contacts the retaining ring (not shown).
14. Install stator (42) to carrier assembly (41) . Install freewheel springs (46) and freewheel
rollers (45) to freewheel cam (47) . Always install new freewheel springs (46) and
freewheel rollers (45) . Install freewheel springs (46) with the maximum number of loops in
freewheel springs (46) to the outside of freewheel cam (47) . Use the orientation of stator
(42) in Illustration 11 in reference to the following statement: Stator (42) should turn freely
in the clockwise direction. Stator (42) should not turn freely in the counterclockwise
direction.
Illustration 12 g00870421
15. Install plate (44) to stator (42) . Install snap ring (43) to stator (42) .
6/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 13 g00870422
16. Install carrier assembly (41) and stator (42) as a unit to rotating housing (36) .
Illustration 14 g00870762
17. Install thrust bearing (40) and race (40A) (not shown) to the carrier assembly (41) .
Illustration 15 g00870994
18. Position impeller hub (39) on a wood block.
7/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 19. Install impeller (38) on impeller hub (39) .
Illustration 16 g00870995
20. Install drive flange (35) on impeller (38) .
Illustration 17 g00871000
21. Install bolts (37) on drive flange (35) . Tighten the bolts to a torque of 80 ± 10 N·m (60 ± 7
lb ft).
8/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 18 g00871001
22. Install drive flange (35) on rotating housing (36) . The weight of drive flange (35) is
approximately 23 kg (51 lb).
23. Install bolts (34) and the washers to drive flange (35) . Tighten the bolts to a torque of 30 ±
5 N·m (22 ± 4 lb ft).
Illustration 19 g00871003
24. Install retaining ring (33) in the groove of drive gear (32) .
9/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 20 g00870829
25. Use the proper equipment to handle outer bearing race (32A) . Lower the temperature of
outer bearing race (32A) .
26. Install outer bearing race (32A) in drive gear (32) . Make sure that outer bearing race (32A)
contact retaining ring (33) .
Illustration 21 g00870763
27. Install drive gear (32) on drive flange (35) .
28. Install bolts (31) and the washers on drive gear (32) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 22 g00871006
29. Use the proper equipment to handle inner bearing (30) . Heat inner bearing (30) to a
maximum temperature of 135 °C (275 °F). Install inner bearing (30) on bearing carrier
(25) .
10/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 23 g00871007
30. Install retaining ring (29) in the groove of bearing carrier (25) .
Illustration 24 g00871009
31. Use the proper equipment to handle ring carrier (28) . Heat ring carrier (28) to a maximum
temperature of 135 °C (275 °F). Install ring carrier (28) on bearing carrier (25) .
Illustration 25 g00871012
11/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
34. 32. Install seal ring (27) on ring carrier (28) .
33. Install O-ring seal (26) on bearing carrier (25) .
Illustration 26 g00871014
34. Install bearing carrier (25) in drive flange (35) .
Illustration 27 g00871015
35. Install retaining ring (24) and bearing carrier (25) on carrier assembly (28) .
12/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. Illustration 28 g00872709
36. Install studs (23) in torque converter housing assembly (2) . Tighten the studs to a torque of
100 ± 15 N·m (74 ± 11 lb ft).
Illustration 29 g00872711
37. Install retaining ring (21) in the groove of idler gear (13) .
Illustration 30 g00872713
13/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. 38. Use the proper equipment to handle bearing cup (22) . Lower the temperature of bearing cup
(22) . Install bearing cup (22) in idler gear (13) .
Illustration 31 g00872715
39. Flip idler gear (13) to the opposite side. Install bearing cup spacer (20) in idler gear (13) .
The notch in bearing cup spacer (20) must be aligned with retaining ring (21) .
Illustration 32 g00872716
40. Use the proper equipment to handle bearing cup (19) . Lower the temperature of bearing cup
(19) . Install bearing cup (19) in idler gear (13) .
14/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...