This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 982M WHEEL LOADER F9A
Configuration: 982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
980M and 982M Wheel Loaders Power Train
Media Number -UENR3097-03 Publication Date -01/09/2018 Date Updated -13/09/2018
i06838048
Torque Converter - Disassemble - Lock Up Clutch With
Freewheel Stator
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B
8B-7548 Push-Puller 1
8B-7550 Leg 2
8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
C
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
D
5F-7343 Bearing Puller Attachment 1
1P-0520 Driver Group 1
E 1P-0510 Driver Group 1
1/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. F 6L-7283 Forcing Bolt
3/8 - 16 by 3 in
7
G 417-1324 Adjust Stand 1
Start By:
a. Separate the torque converter from the transmission and from the output transfer gears.
Illustration 1 g02712129
1. Use Tooling (A) and a suitable lifting device to position the torque converter onto Tooling
(G) and suitable blocking. The weight of the torque converter is approximately 260 kg
(573 lb). Support the torque converter, as shown.
2. Remove bolts (1).
Illustration 2 g02730506
3. Remove relief valve assembly (2A).
2/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02711758
4. Use Tooling (F) to loosen housing assembly (2) from the torque converter.
5. Use the suitable lifting device and Tooling (A) to remove torque converter housing
assembly (2). The weight of torque converter housing assembly (2) is approximately 144 kg
(317 lb).
Illustration 4 g00871317
6. Remove O-ring seal (3) from torque converter housing assembly (2).
Illustration 5 g00871318
3/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Remove bolts (4) from pump adapter (5) and torque converter housing assembly (2).
Illustration 6 g00871264
8. Use Tooling (F) to remove pump adapter (5) from torque converter housing assembly (2).
Illustration 7 g00871319
9. Use Tooling (B) to remove bearing cup (6). Remove bearing cup (6), O-ring seal (8), and
shims (7) from pump adapter (5). See illustration 14 for Tooling (C).
Illustration 8 g00871326
10. Remove pump drive gear (9) from torque converter housing assembly (2).
4/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00871451
11. Use Tooling (C) to remove bearing cones (10) from each side of pump drive gear (9).
Remove bearing cones (10).
Illustration 10 g00871333
12. Use Tooling (C) to remove bearing cup (11) from torque converter housing assembly (2).
See illustration 14 for Tooling (C).
Illustration 11 g01112900
13. Remove bolt (12) and the washer from torque converter housing assembly (2).
5/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (F) to push shaft assembly (14) out of torque converter housing assembly (2).
15. Remove idler gear (13) from torque converter housing assembly (2).
Illustration 12 g01112903
16. Remove O-ring seal (15) from shaft assembly (14).
Illustration 13 g00871365
17. Remove bearing cone (16), bearing cone spacer (17), and bearing cone (18) from idler gear
(13).
6/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00871366
18. Use Tooling (C) to remove bearing cup (19) from idler gear (13). Remove bearing cup (19).
Illustration 15 g00871367
19. Remove bearing cup spacer (20) from idler gear (13).
Illustration 16 g00871368
7/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Remove retaining ring (21) from idler gear (13).
Illustration 17 g00871369
21. Use Tooling (C) to remove bearing cup (22) from idler gear (13). Remove bearing cup (22).
Illustration 18 g00871370
22. Remove studs (23) from torque converter housing assembly (2).
8/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g02729366
23. Remove bolts (24) and gear (25).
Illustration 20 g02735357
24. Use the driver group from Tooling (D) and a suitable press to remove race (25A) from gear
(25).
Illustration 21 g02730012
25. Use a suitable lifting device to reposition the torque converter, as shown. The weight of the
torque converter is approximately 122 kg (269 lb). Remove bolts (26).
9/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g02730687
26. Use Tooling (F) to separate housing (27) from the torque converter.
Illustration 23 g02730689
27. Use two people to remove housing (27). The weight of housing (27) is approximately 26 kg
(57 lb). Remove housing (27), piston (28), and plate (30). Remove seals (29) from piston
(28).
Illustration 24 g02731059
28. Remove bushing (31) from housing (27).
10/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 25 g02731623
29. Remove plate (32), disk (33), races (34), and bearing (35).
Note: Note the orientation of the bearing and races for assembly purposes.
Illustration 26 g02731644
30. Remove bolts (36), coupling assembly (37), and plate (38).
11/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 27 g02731651
31. Use suitable blocking to support the bottom of shaft assembly (39). Remove retaining ring
(40) and plate (41). Shaft assembly (39) can be lowered to the work bench.
Illustration 28 g02731711
Illustration 29 g02732048
12/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 32. Install two of bolts (36) and remove turbine (42).
33. Remove bolts (36) and remove hub (43) from turbine (42).
Illustration 30 g02731732
Illustration 31 g02731802
34. Remove race (44) and bearing (45).
Note: Note the orientation of the race and bearing for assembly purposes.
35. Remove stator assembly (46).
13/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 32 g02731806
36. Remove retaining ring (47), plate (48), freewheel springs (49), freewheel rollers (50), and
freewheel cam (51). Remove plate (52) and retaining ring (53) (not shown) from stator (46).
Illustration 33 g02732255
37. Attach Tooling (A) and a suitable lifting device to impeller (54). The weightof impeller (54)
is approximately 27 kg (60 lb).
38. Remove impeller (54) from shaft assembly (39).
Illustration 34 g02735333
39. Position impeller (54) onto suitable blocking, as shown.
14/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 35 g02734776
40. Remove retaining ring (56) and hub (55).
Illustration 36 g02735372
41. Remove seal ring (56).
Illustration 37 g02734816
42. Use Tooling (D) and a suitable press to remove bearing (57).
Illustration 38 g02735374
15/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 43. Remove retaining ring (59) and carrier assembly (58) from impeller (54).
Illustration 39 g02735380
44. Remove bearing (60).
Note: Note the orientation of the bearing (60) for assembly purposes.
Illustration 40 g02735387
45. Remove bolts (61), hub (62), and adapter (63) from impeller (54).
16/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 41 g02752296
46. Remove seals (64).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 11 09:35:12 UTC+0800 2021
17/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 982M WHEEL LOADER F9A
Configuration: 982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
980M and 982M Wheel Loaders Power Train
Media Number -UENR3097-03 Publication Date -01/09/2018 Date Updated -13/09/2018
i06838485
Torque Converter - Assemble - Lock Up Clutch with
Freewheel Stator
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
G
8T-5096 Dial Indicator Test Group 1
5P-2390 Gauge Tool Group 1
H 1P-0520 Driver Group 1
J -
Guide Stud
(3/8 - 16 by 8 in)
2
K -
Guide Stud
(1/2 - 13 by 3 in)
3
L 2P-8312 Retaining Ring Pliers 1
1/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g02735374
4. Install carrier assembly (58) and retaining ring (59) onto impeller (54).
Illustration 5 g02744677
5. Raise the temperature of bearing (57). Install bearing (57) onto hub (55).
6. Install seal ring (56).
Illustration 6 g02734776
3/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g02735333
7. Install hub (55) and retaining ring (56) onto impeller (54).
Illustration 8 g02732255
8. Attach Tooling (A) and a suitable lifting device to impeller (54). The weight of impeller
(54) is approximately 27 kg (60 lb).
9. Position impeller (54) onto shaft assembly (39).
Illustration 9 g02731806
10. Install retaining ring (53) (not shown) and plate (52) onto stator (46).
4/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 11. Install freewheel cam (51), freewheel rollers (50), and springs (49).
Note: Springs (49) must be installed with the maximum number or loops to the outside.
12. Install plate (48) and retaining ring (47).
Illustration 10 g02731802
Illustration 11 g02731732
13. Install stator assembly (46).
14. Install bearing (45) and race (44).
5/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 12 g02744699
Illustration 13 g02731651
15. Install hub (43) and turbine (42).
16. Use two of bolts (36) to align the holes.
17. Use suitable blocking to support the bottom of shaft assembly (39). Install plate (41) and
retaining ring (40).
Illustration 14 g02731644
18. Install plate (38), coupling assembly (37), and bolts (36). Tighten bolts (36) to a torque of
60 ± 7 N·m (44 ± 5 lb ft).
6/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 15 g02731623
19. Install plate (32), disk (33), races (34), and bearing (35).
Illustration 16 g02731059
20. Lower the temperature of bushing (31). Install bushing (31) into housing (27).
7/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 23. Lower the temperature of race (25A). If necessary, use the driver group from Tooling (D)
and a suitable press to install race (25A) into gear (25).
Illustration 20 g02729366
24. Use a suitable lifting device to reposition the torque converter, as shown. The weight of the
torque converter is approximately 122 kg (269 lb).
25. Install drive gear (25) and bolts (24). Tighten the bolts to a torque of 50 ± 7 N·m
(37 ± 5 lb ft).
Illustration 21 g00872709
26. Install studs (23) in torque converter housing assembly (2). Tighten the studs to a torque of
100 ± 15 N·m (74 ± 11 lb ft).
9/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 22 g00872711
27. Install retaining ring (21) in the groove of idler gear (13).
Illustration 23 g00872713
28. Use the proper equipment to handle bearing cup (22). Lower the temperature of bearing cup
(22). Install bearing cup (22) in idler gear (13).
Illustration 24 g00872715
29. Flip idler gear (13) to the opposite side. Install bearing cup spacer (20) in idler gear (13).
The notch in bearing cup spacer (20) must be aligned with retaining ring (21).
10/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 25 g00872716
30. Use the proper equipment to handle bearing cup (19). Lower the temperature of bearing cup
(19). Install bearing cup (19) in idler gear (13).
Illustration 26 g00872718
31. Install bearing cone (16), bearing cone spacer (17), and bearing cone (18) in idler gear (13).
Illustration 27 g01112903
32. Apply clean hydraulic oil on O-ring seal (15). Install O-ring seal (15) on shaft assembly
(14).
11/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Illustration 28 g01112954
33. Install Tooling (K) in shaft assembly (14).
34. Hold idler gear (13) in position in torque converter housing assembly (2). Install shaft
assembly (14).
35. Remove Tooling (K) from shaft assembly (14).
Illustration 29 g01112970
36. Install bolt (12) that holds shaft assembly (14) in place in torque converter housing
assembly (2). Tighten bolt (12) to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
Illustration 30 g00872724
37. Use the proper equipment to handle bearing cones (10). Heat bearing cones to a maximum
temperature of 135 °C (275 °F). Install bearing cone (10) on each side of pump drive gear
(9).
12/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 31 g00872801
38. Use the proper equipment to handle bearing cup (11). Lower the temperature of bearing cup
(11). Install bearing cup (11) in torque converter housing assembly (2).
Illustration 32 g00872727
39. Install pump drive gear (9) in torque converter housing assembly (2).
Illustration 33 g00872729
40. Use the proper equipment to handle bearing cup (6). Lower the temperature of bearing cup
(6).
13/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 34 g00871319
41. Apply clean hydraulic oil on O-ring seal (8).
42. Install bearing cup (6), O-ring seal (8), and shims (7) on pump adapter (5).
Illustration 35 g01112978
43. Install Tooling (J) in torque converter housing assembly (2).
44. Install pump adapter (5) on torque converter housing assembly (2).
Illustration 36 g01112982
14/17
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...