This document provides instructions for removing and installing the fuel filter, fuel filter base, engine oil filter, and engine oil filter base on a 307D Mini Hydraulic Excavator. It lists the required tools and safety precautions and provides detailed step-by-step procedures with illustrations for removing, disassembling, assembling, and installing each component. Special attention is paid to cleanliness, containment of fluids, and proper tightening of bolts and connectors.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...hvy7sbkw8e
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of parts. Safety notices are
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...xiapokang564341
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of key components. Safety notices
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...wenxian17880
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of key components. Safety notices
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...tuzhiyou2
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the fuel injection pump
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
- Removing and installing the exhaust gas recirculation valve
The instructions include safety warnings and step-by-step procedures for each component.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...qfyc504378
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
- Removing and installing the exhaust gas recirculation valve
The procedures provide illustrations and specify torque values for fasteners. Safety notices are included regarding working with high pressure fuel and draining coolant.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...lituo39419496
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
The procedures provide illustrations and step-by-step instructions and include safety warnings for working on high pressure fuel systems and draining hot coolant. Torque specifications are provided for reinstalling components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fjskekfseik
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR Mini Hydraulic Excavator including:
- Fuel injection lines
- Exhaust gas recirculation cooler
- Fuel injection pump
- Electronic unit injector
- Turbocharger
- Exhaust gas recirculation valve
The procedures describe removing parts like hoses, brackets, and mounting hardware and reinstalling components in the reverse order, taking safety precautions for high pressure fuel lines and hot engine components.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...hvy7sbkw8e
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of parts. Safety notices are
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...xiapokang564341
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of key components. Safety notices
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...wenxian17880
This service repair manual provides instructions for removing and installing various components on a 307D Mini Hydraulic Excavator including:
1) The fuel filter and water separator base, including draining the fuel and removing/installing the filter and base.
2) The engine oil filter and oil filter base, including removing hoses and bolts to access the filter and base.
3) Procedures for disassembling and assembling the engine oil filter base.
4) Removing and installing the air cleaner housing and primary/secondary air filter elements.
The document provides detailed step-by-step instructions and illustrations for maintenance technicians to perform repairs and replacements of key components. Safety notices
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...tuzhiyou2
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the fuel injection pump
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
- Removing and installing the exhaust gas recirculation valve
The instructions include safety warnings and step-by-step procedures for each component.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...qfyc504378
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
- Removing and installing the exhaust gas recirculation valve
The procedures provide illustrations and specify torque values for fasteners. Safety notices are included regarding working with high pressure fuel and draining coolant.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...lituo39419496
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 powered by a C2.4 engine, including:
- Removing and installing the fuel manifold (rail)
- Removing and installing the fuel injection lines
- Removing and installing the electronic unit injector
- Removing and installing the turbocharger
The procedures provide illustrations and step-by-step instructions and include safety warnings for working on high pressure fuel systems and draining hot coolant. Torque specifications are provided for reinstalling components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fjskekfseik
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR Mini Hydraulic Excavator including:
- Fuel injection lines
- Exhaust gas recirculation cooler
- Fuel injection pump
- Electronic unit injector
- Turbocharger
- Exhaust gas recirculation valve
The procedures describe removing parts like hoses, brackets, and mounting hardware and reinstalling components in the reverse order, taking safety precautions for high pressure fuel lines and hot engine components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...f7djidksmd3e
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...uddksemd8ud
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and other fasteners, and reversing the steps for installation. Safety notices are included regarding handling of fuels and working on high pressure fuel systems.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...f8usiedkdmm
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and other fasteners, and reversing the steps to install components. Safety notices warn of hazards such as high pressure fuel, sulfuric acid, and hot coolant.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...jdjkskmikdkmd
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while following safety precautions for high pressure fuel and hot coolant.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...cdfvvv1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...yan77xunhao
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while following safety precautions for high pressure fuel systems.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix bz5) service repai...fjskekfseik
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing fuel injection lines by disconnecting hose assemblies and removing bolts, clamps and tubes.
- Removing the exhaust gas recirculation cooler by draining coolant, removing hoses and brackets, and bolts.
- Removing the fuel injection pump by disconnecting harnesses and hoses, and removing nuts, bolts and the pump.
- Removing electronic unit injectors by disconnecting hoses after draining fuel and removing clips and hoses.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...hvy7sbkw8e
1. The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, electronic unit injector, turbocharger, and exhaust gas recirculation valve.
2. Safety precautions are outlined that must be followed when working on fuel, coolant, and exhaust systems due to risks of burns, fires, and toxic fumes.
3. The procedures provide illustrated steps for loosening bolts and disconnecting hoses to remove each part, then reversing the process for installation. Torque specifications are given for reinstalling bolts.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...xiapokang564341
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. The procedures note safety hazards and provide illustrations showing the components and installation/removal steps, which include disconnecting hoses and lines, removing bolts and nuts, and installing components in reverse order. Precautions are described such as capping open ports to prevent contamination.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...wenxian17880
1. The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, electronic unit injector, turbocharger, and exhaust gas recirculation valve.
2. Safety precautions are outlined that must be followed when working on fuel, coolant, and exhaust systems due to risks of burns, fires, and toxic fumes.
3. The procedures provide illustrated steps for draining fluids, loosening bolts and connections, removing parts, and installing parts in the reverse order of removal while following torque specifications.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...paws21610697
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe removing mounting hardware and disconnecting fluid lines before removing each component, then installing in the reverse order. Safety notices warn of burn hazards from hot coolant and high pressure fuel.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...f7djidksmd3e
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and lines, taking care not to damage sensors.
- Removing fuel injection lines by disconnecting hoses and tubes after capping lines to prevent contamination.
- Removing the exhaust gas recirculation cooler by draining coolant and removing hoses and mounting brackets.
- Removing the fuel injection pump by disconnecting lines and hoses after removing mounting nuts and bolts.
- Removing electronic unit injectors by disconnecting hoses after draining and capping fuel lines to prevent contamination or injury from high pressure fuel.
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
More Related Content
Similar to Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Manual (DSG00001 and up).pdf
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...f7djidksmd3e
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...uddksemd8ud
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and other fasteners, and reversing the steps for installation. Safety notices are included regarding handling of fuels and working on high pressure fuel systems.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...f8usiedkdmm
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and other fasteners, and reversing the steps to install components. Safety notices warn of hazards such as high pressure fuel, sulfuric acid, and hot coolant.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...jdjkskmikdkmd
The document provides instructions for removing and installing various engine components of a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while following safety precautions for high pressure fuel and hot coolant.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...cdfvvv1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix DF5) Service Repair...yan77xunhao
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR Mini Hydraulic Excavator, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while following safety precautions for high pressure fuel systems.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix bz5) service repai...fjskekfseik
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing fuel injection lines by disconnecting hose assemblies and removing bolts, clamps and tubes.
- Removing the exhaust gas recirculation cooler by draining coolant, removing hoses and brackets, and bolts.
- Removing the fuel injection pump by disconnecting harnesses and hoses, and removing nuts, bolts and the pump.
- Removing electronic unit injectors by disconnecting hoses after draining fuel and removing clips and hoses.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...hvy7sbkw8e
1. The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, electronic unit injector, turbocharger, and exhaust gas recirculation valve.
2. Safety precautions are outlined that must be followed when working on fuel, coolant, and exhaust systems due to risks of burns, fires, and toxic fumes.
3. The procedures provide illustrated steps for loosening bolts and disconnecting hoses to remove each part, then reversing the process for installation. Torque specifications are given for reinstalling bolts.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...xiapokang564341
The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. The procedures note safety hazards and provide illustrations showing the components and installation/removal steps, which include disconnecting hoses and lines, removing bolts and nuts, and installing components in reverse order. Precautions are described such as capping open ports to prevent contamination.
Caterpillar Cat 307E2 Mini Hydraulic Excavator (Prefix KC9) Service Repair Ma...wenxian17880
1. The document provides instructions for removing and installing various components of a 307E2 Mini Hydraulic Excavator engine, including the fuel manifold, fuel injection lines, electronic unit injector, turbocharger, and exhaust gas recirculation valve.
2. Safety precautions are outlined that must be followed when working on fuel, coolant, and exhaust systems due to risks of burns, fires, and toxic fumes.
3. The procedures provide illustrated steps for draining fluids, loosening bolts and connections, removing parts, and installing parts in the reverse order of removal while following torque specifications.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...paws21610697
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator BZ5 engine, including the fuel manifold, fuel injection lines, fuel injection pump, electronic unit injector, turbocharger, and exhaust gas recirculation valve. The procedures describe removing mounting hardware and disconnecting fluid lines before removing each component, then installing in the reverse order. Safety notices warn of burn hazards from hot coolant and high pressure fuel.
Caterpillar Cat 305E2 CR Mini Hydraulic Excavator (Prefix BZ5) Service Repair...f7djidksmd3e
This document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including:
- Removing the fuel manifold by removing bolts and lines, taking care not to damage sensors.
- Removing fuel injection lines by disconnecting hoses and tubes after capping lines to prevent contamination.
- Removing the exhaust gas recirculation cooler by draining coolant and removing hoses and mounting brackets.
- Removing the fuel injection pump by disconnecting lines and hoses after removing mounting nuts and bolts.
- Removing electronic unit injectors by disconnecting hoses after draining and capping fuel lines to prevent contamination or injury from high pressure fuel.
Similar to Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Manual (DSG00001 and up).pdf (13)
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
This document provides instructions for removing and installing various components of a 3054C engine, including:
1) The crankshaft pulley, which is removed by taking out setscrews and the thrust block.
2) The crankshaft front seal, which is pulled out using a suitable puller to avoid damaging the housing.
3) The front cover, which is secured by setscrews and gasket and must be cleaned before installation.
This document provides assembly instructions for the transmission of a 416D Backhoe Loader. It includes notes on cleaning and preparation, lists required tools, and provides detailed step-by-step instructions and illustrations for assembling the transmission components in the following order: reverse shaft assembly, input shaft assembly, and shaft assembly. Precautions are given for lubrication, seals, and bearing installation temperatures.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the removal and installation steps. The removal process involves using a lifting device to remove the flywheel and housing, while installation requires heating the flywheel ring gear and using a press and alignment tool to correctly position the rear seal and housing. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires loosening bolts and using a lifting device due to its weight of 53 kg. Installation of the crankshaft rear seal involves cleaning, lubricating, and pressing the seal into place using the proper tool. Proper torque values are also provided for reinstalling components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It describes:
1. Removing the electric starting motor and flywheel first.
2. Using link brackets as required tools to support the flywheel housing during removal and installation.
3. Removing bolts to separate the flywheel housing from the engine, and installing new bolts to secure the housing during reinstallation.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and gives step-by-step procedures for both removing and installing the seal. For engines with a 14-bolt housing, the instructions explain how to remove the housing, seal, and gasket before installing the new gasket and seal and reattaching the housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed and installed as a unit.
The document provides instructions for removing and disassembling the valve mechanism cover, rocker shaft, and associated components of a Caterpillar C4.4 engine. It describes removing the valve mechanism cover and brackets. It then details using a tool to rotate the crankshaft and position the valves, loosening threaded inserts on the rocker arms, and removing the rocker shaft assembly and pushrods while marking their positions. Finally, it explains disassembling the rocker shaft assembly by removing screws, retaining clips, springs, and separating the rocker arm assemblies.
John Deere XUV 620i Gator Utility Vehicle Service Repair Manual.pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere Gator XUV 620i utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, maintenance, and repairs. It is intended as a resource for experienced technicians working with this product. Safety notices and procedures are highlighted throughout to warn of hazards during service.
John Deere XUV 850D Gator Utility Vehicle Service Repair Manual (tm1737).pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It aims to keep all information for a particular system together to aid technicians in servicing this vehicle. Safety is the first section and warns of dangers of fuel and working around heaters or other fire hazards.
This document provides instructions for removing and installing an engine in a 420F2 backhoe loader. It outlines 17 steps for removing the engine, which include disconnecting wiring harnesses, hoses, and other components. It then outlines 17 steps for installing the new engine, which involve connecting all the removed components in reverse order. Tools required include a hydraulic jack and load leveling beam to lift the heavy engine. Safety notices are provided to keep components clean and contain fluids.
The document provides instructions for removing and installing various components of the rear drive and steering axle assembly of a 420D backhoe loader, including:
- Removing the rear tires, drive shaft brackets, parking brake assembly, hydraulic hoses, manifold brackets, rear steer sensor wire, and axle mounting nuts and plates.
- Positioning a hydraulic jack under the axle and using a lifting device to remove the axle from the vehicle.
- Removing additional components from the axle including a parking brake bracket, cover, retaining clip, pin and washer.
The procedures include illustrations of each step and require tools such as a puller, wrench, heat gun and hydraulic jack. Safety notices
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03021635
Fuel Filter and Water Separator Base - Remove and Install
SMCS - 1262-010; 1263-010-BA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the fuel supply to the OFF position.
1/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01527554
2. Open door assembly (1) .
Illustration 2 g01527555
3. Drain the fuel from sediment bowl (6) into a suitable container for storage or for disposal.
Remove sediment bowl (6) .
4. Use Tooling (A) in order to remove fuel filter (5) .
5. Disconnect hose assemblies (2). Plug and cap all open ports and hose assemblies (2). This
helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
6. Remove bolts (3) and remove filter base (4) .
Installation Procedure
2/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01527555
1. Position filter base (4) and install bolts (3) .
2. Connect hose assemblies (2) .
3. Install fuel filter (5). Install sediment bowl (6) .
Illustration 4 g01527554
4. Close door assembly (1) .
5. Turn the fuel supply back to the ON position.
6. Prime the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime"
for instruction.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 22:58:15 UTC+0800 2020
3/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03012380
Engine Oil Filter and Oil Filter Base - Remove
SMCS - 1306-011; 1308-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact the skin.
Be sure that the engine and components are cool enough to touch with
your bare hand prior to performing any service work.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hose assemblies for installation purposes. Plug all hose
assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep
contaminants from entering the system.
Illustration 1 g01525027
1. Raise the hood and disconnect hose assemblies (3) .
2. Use Tooling (A) in order to remove oil filter (4). Remove bolts (1) and the nuts. Remove
filter base (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 22:59:12 UTC+0800 2020
2/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i01694637
Engine Oil Filter Base - Disassemble
SMCS - 1306-015; 1306
Disassembly Procedure
Start By:
A. Remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter and Oil Filter
Base - Remove" for the proper procedure.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Put orientation and location marks on all fittings for installation purposes.
Illustration 1 g00872494
1/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Remove fittings (1), fittings (2), and washers (3).
2. Remove plug (4) .
Illustration 2 g00872502
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (5), washer (6), spring (7), and piston (8).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 23:00:09 UTC+0800 2020
2/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i01694716
Engine Oil Filter Base - Assemble
SMCS - 1306-016; 1306
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Perform assembly procedures on a clean work surface.
Keep components covered and protected at all times.
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00872502
1. Install piston (8), spring (7), washer (6), and plug (5) .
Illustration 2 g00872494
2. Install plug (4) .
3. Install washers (3), fittings (2), and fittings (1) .
End By: Install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter and Oil Filter
Base - Install" for the proper procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 23:01:06 UTC+0800 2020
2/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03012381
Engine Oil Filter and Oil Filter Base - Install
SMCS - 1306-012; 1308-012; 1318-012
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01525027
1. Position filter base (2) and install bolts (1) and the nuts. Tighten the bolts to a torque of 44 ±
10 N·m (32 ± 7 lb ft).
2. Install hose assemblies (3). Tighten the connectors to a torque of 78 ± 10 N·m (58 ± 7 lb ft).
3. Apply clean engine oil to the seal of oil filter (4). Install oil filter (4). Refer to Operation and
Maintenance Manual, "Maintenance Interval Schedule" for the service interval for the
engine oil filter.
4. Lower the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 23:02:02 UTC+0800 2020
2/2
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03007176
Air Cleaner - Remove and Install
SMCS - 1051-010; 1054-010
Removal Procedure
Illustration 1 g01523578
1. Open door assembly (2). Raise hood assembly (1) .
1/4
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01524975
2. Remove cover assembly (3) .
Illustration 3 g01524990
Illustration 4 g01524993
3. Remove primary air filter element (4). Remove secondary air filter element (5) .
4. Remove hose (7). Remove bolts (8) and remove air cleaner (6) .
2/4
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Installation Procedure
Note: Refer to Operation and Maintenance Manual, SEBU8340, "Engine Air Filter Element -
Clean/Replace" for information on servicing the filter elements.
Illustration 5 g01524993
Illustration 6 g01524990
1. Position air cleaner (6) and install bolts (8). Install hose (7) .
2. Install secondary air filter element (5). Install primary air filter element (4) .
3/4
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g01524975
3. Install cover assembly (3) .
Illustration 8 g01523578
4. Lower hood assembly (1). Close door assembly (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 23:02:59 UTC+0800 2020
4/4
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03007177
Aftercooler - Remove and Install
SMCS - 1063-010
Removal Procedure
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of
the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism.
Illustration 1 g01523578
1. Open door assembly (2). Raise hood assembly (1) .
1/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01524953
2. Remove hoses (3). Remove bolts (4) and remove aftercooler (5) .
Installation Procedure
Note: Cleanliness is an important factor. Before you begin the installation procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism.
Illustration 3 g01524953
1. Position aftercooler (5) and install bolts (4). Install hoses (3) .
2/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01523578
2. Lower hood assembly (1). Close door assembly (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 23:03:56 UTC+0800 2020
3/3
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307D MINI HYD EXCAVATOR DSG
Configuration: 307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307D Excavator Engine Supplement
Media Number -RENR9743-01 Publication Date -01/11/2011 Date Updated -08/11/2011
i03016745
Muffler - Remove and Install
SMCS - 1062-010
Removal Procedure
1. Open the engine hood.
Illustration 1 g01526036
2. Remove exhaust stack (1). Remove clamp (3) and cover (2) .
1/5
307D Mini Hydraulic Excavator DSG00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...