Caterpillar Cat 308ECR Mini Hydraulic Excavator (Prefix HAM) Service Repair Manual (HAM00001 and up).pdf

Service Repair Manual
Models
308ECR Mini Hydraulic
Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E CR MINI HYD EXCAVATOR HAM
Configuration: 308E CR Mini Hydraulic Excavator HAM00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
308ECR and 308ESR Mini Hydraulic Excavators Machine Systems
Media Number -UENR3284-03 Publication Date -01/12/2017 Date Updated -05/12/2017
i04808935
Front Idler and Recoil Spring - Remove
SMCS - 4158-011; 4159-011
Removal Procedure
Start By:
a. Remove the rubber track. Refer to Disassembly and Assembly, "Track - Remove and
Install".
Illustration 1 g00551666
1/2
308E CR Mini Hydraulic Excavator HAM00001-UP (MACHINE) POWERED BY C3...
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

1. Pull the front idler and recoil spring assembly (1) partially out of the undercarriage frame.
Attach a suitable lifting device to the front idler. Pull the front idler and recoil spring
assembly out of the undercarriage frame until the recoil spring is exposed.
2. Reposition the lifting device to the front idler and the recoil spring assembly. Remove the
front idler and recoil spring assembly (1) from the undercarriage frame. The weight of the
unit is approximately 81 kg (179 lb).
3. Position the front idler and recoil spring assembly horizontally. Block the unit in position in
order to keep the unit from falling. Attach a suitable lifting device to recoil spring (2).
Remove four bolts (3) and separate recoil spring (2) from front idler (4). The weight of the
recoil spring is approximately 27 kg (60 lb). The weight of the front idler is approximately
54 kg (120 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 14 00:06:09 UTC+0800 2020
2/2
2020/1/14

Shutdown SIS
Previous Screen
i04808945
Front Idler and Recoil Spring - Install
SMCS - 4158-012; 4159-012
Installation Procedure
1. Prior to assembly, ensure that the mating surfaces of the front idler bearings and of the
recoil spring assembly are clean and free of dirt and debris.
2. Attach a suitable lifting device to recoil spring assembly (2). The weight of the recoil spring
assembly is approximately 27 kg (60 lb). Position the recoil spring assembly against the
bearings on front idler (4) and install four bolts (3).
1/2
2020/1/14

3. Attach a suitable lifting device to the front idler and recoil spring assembly (1). The weight
of the front idler and recoil spring assembly is approximately 81 kg (179 lb). Put the front
idler of the unit partially into the undercarriage frame.
4. Use a pry bar to slide the front idler and recoil spring assembly (1) into position in the
undercarriage frame.
End By:
a. Install the rubber track. Refer to Disassembly and Assembly, "Track - Remove and Install".
Tue Jan 14 00:07:05 UTC+0800 2020
2/2
2020/1/14

Shutdown SIS
Previous Screen
i04808991
Recoil Spring - Disassemble
SMCS - 4158-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9540 Recoil Spring Bench 1
(B)
146-2457 Hydraulic Power Supply Gp 1
223-3506 Hydraulic Cylinder and Lines Gp 1
C
8F-0024 Hose Assembly 2
3B-7722 Bushing 2
1P-2376 Coupler Assembly 2
1P-2377 Plug 1
D 8S-9971 Adapter for Ram 1
Start By:
a. Remove front idlers and recoil springs. Refer to Disassembly and Assembly, "Front Idler
and Recoil Spring - Remove".
Note: Adjust the pump relief valve. To avoid damage or injury, the pressure should not
exceed 51366 kPa (7450 psi).
1/5
2020/1/14

Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
1. Thoroughly clean the outside of the recoil spring assembly.
2. Install Tooling (D) on Tooling (B), as shown.
(1) Adjustable support
2/5
2020/1/14

Tooling (A)
( 2) Reaction plate
(3) Movable plate
3. Determine the position for the recoil spring assembly in Tooling (A). Locate adjustable
support (1) of Tooling (A) in this position. Level the adjustable support.
4. Measure the length of the recoil spring assembly. Adjust the space from reaction plate (2) to
movable plate (3) in order to fit the measured length.
5. Remove bolt (5) and lock plate (4) from the end of the retaining rod for the recoil spring
assembly.
3/5
2020/1/14

6. Attach a suitable lifting device to recoil spring assembly (6). The weight of the recoil spring
assembly is approximately 24 kg (53 lb). Position the recoil spring assembly on adjustable
support (1) in Tooling (A). Align the centerline of the recoil spring assembly with the
centerline of Tooling (A) by moving the adjustable support.
7. Use the following procedure to position the recoil spring assembly in Tooling (A).
a. Level the recoil spring assembly by repositioning the adjustable support.
b. Position the recoil spring assembly so that nut (8) is centered in the hole of reaction
plate (2).
c. Install two pins (7) on the back side of reaction plate (2), as shown.
d. Operate Tooling (B) enough to hold the recoil spring assembly in position between
reaction plate (2) and movable plate (3).
e. Be sure that the recoil spring assembly is leveled and centered in Tooling (A).
8. Close covers (9) on Tooling (A). Operate Tooling (B) and slowly compress the recoil spring
assembly until the retaining rod and the nut are free to move.
4/5
2020/1/14

9. Locate nut (8) through the opening in Tooling (A). Remove nut (8) and the washer from the
retaining rod. Use Tooling (B) and slowly release the force on the recoil spring assembly.
10. Open covers (9) on Tooling (A). Attach a suitable lifting device to the disassembled recoil
spring assembly. Remove the recoil spring assembly from Tooling (A).
11. Separate the components of the recoil spring assembly. Remove retaining rod (13), support
assembly (12), and support (10) from recoil spring (11).
Tue Jan 14 00:08:02 UTC+0800 2020
5/5
2020/1/14

Shutdown SIS
Previous Screen
i07524158
Recoil Spring - Assemble
SMCS - 4158-016
Assembly Procedure
Table 1
Required Tools
A 4C-9540 Recoil Spring Bench 1
B
146-2457 Hydraulic Power Supply Gp 1
223-3506 Hydraulic Cylinder and Lines Gp 1
C
8F-0024 Hose Assembly 2
3B-7722 Bushing 2
1P-2376 Coupler Assembly 2
1P-2377 Plug 1
D 8S-9971 Adapter for Ram 1
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
1/6
2020/1/14

1. Check the condition of the threads on retaining rod (13) and nut (8). If the threads are
damaged, use new parts for replacement.
2. Install Tooling (D) on Tooling (B), as shown.
(1) Adjustable support
2/6
2020/1/14

Tooling (A)
( 2) Reaction plate
(3) Movable plate
3. Determine the position for the recoil spring assembly in Tooling (A). Place adjustable
support (1) of Tooling (A) in this position. Level the adjustable support.
4. Assemble the recoil spring assembly loosely. Apply 4C-5592 Anti-Seize Compound to the
threads of the retaining rod. Install retaining rod (13) in support assembly (12). Install recoil
spring (11) on support assembly (12). Put support (10) in position on recoil spring (11).
3/6
2020/1/14

5. Attach a suitable lifting device to the recoil spring assembly. Position the recoil spring
assembly in Tooling (A). The weight of the recoil spring assembly is approximately 24 kg
(53 lb). Use the following procedure to position the recoil spring assembly in Tooling (A).
a. Level the recoil spring assembly by repositioning the adjustable support (1).
b. Position the recoil spring assembly so that nut (8) and the washer can be installed
through the access hole in reaction plate (2).
c. Install two pins (7) on the back side of reaction plate (2), as shown.
d. Operate Tooling (B) enough to hold the recoil spring assembly in position between
reaction plate (2) and movable plate (3).
e. Be sure that the recoil spring assembly is leveled and centered in Tooling (A).
f. Remove the hoist from the recoil spring assembly.
6. Close covers (9) on Tooling (A). Use the following procedure to adjust the preloaded length
of the recoil spring assembly.
4/6
2020/1/14

a. Operate Tooling (B) and slowly compress the recoil spring assembly. Use the access
hole in reaction plate (2) and guide the end of the retaining rod into position in
support (10).
b. Open the covers on Tooling (A). Determine Dimension (X) by measuring the length
of recoil spring (11) and support (12). Dimension (X) must be 361 ± 1 mm
(14.21 ± 0.04 inch).
c. If the compressed length of the recoil spring is not correct, close covers (9) on
Tooling (A). Use Tooling (B) to adjust Dimension (X) to the correct length.
d. If the compressed length of the recoil spring is correct, assembly of the recoil spring
assembly can be completed.
e. Install the washer and nut (8). Be sure that all the threads in nut (8) are engaged with
threads on the retaining rod.
7. Operate Tooling (B) and release the pressure on the recoil spring assembly. Open the covers
on Tooling (A).
8. Attach a suitable lifting device to recoil spring assembly (6). Remove the recoil spring
assembly from Tooling (A).
5/6
2020/1/14

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

9. Apply 9S-3263 Thread Lock Compound on the threads of bolt (5). Install lock plate (4) and
bolt (5) on the retaining rod. Tighten the bolt to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
End By:
a. Install the front idler and recoil spring assembly. Refer to Disassembly and Assembly,
"Front Idler and Recoil Spring - Install".
Tue Jan 14 00:08:59 UTC+0800 2020
6/6
2020/1/14

Shutdown SIS
Previous Screen
i07190579
Hydraulic Track Adjusters - Remove
SMCS - 4157-011
Removal Procedure
Table 1
Required Tools
A 422-8733 Jack Stand 2
Start By:
a. Remove the track.
Note: Adjust the height of Tooling (A) to provide sufficient clearance for the removal of the
hydraulic track adjuster when Tooling (A) is installed under the frame of the machine.
1/3
2020/1/14

Though the above Illustration represents a machine with steel tracks, the procedure is representative of
machines with rubber tracks.
1. Raise the side of the machine, and install Tooling (A) under the frame.
2. Remove the track roller that is located under the hydraulic track adjuster. Refer to
Disassembly and Assembly, "Track Roller - Remove and Install".
3. Use a pry bar to move the front idler and recoil spring assembly forward approximately
152 mm (6.0 inch) in the undercarriage frame.
Note: The front track carrier roller has been removed to provide a better illustration of two
mounting bolts (1) that secure the hydraulic track adjuster to the vertical bulkhead in the
undercarriage frame.
4. Loosen, but do not remove bolts (1) that secure the hydraulic track adjuster to the
undercarriage frame. Access bolts (1) through the opening in the undercarriage frame below
the track carrier roller.
2/3
2020/1/14

5. The weight of hydraulic track adjuster (2) is approximately 10 kg (22 lb). Remove bolts (1)
and remove hydraulic track adjuster (2).
Tue Jan 14 00:09:56 UTC+0800 2020
3/3
2020/1/14

Shutdown SIS
Previous Screen
i07190459
Hydraulic Track Adjusters - Install
SMCS - 4157-012
Installation Procedure
Table 1
Required Tools
A 422-8733 Jack Stand 2
1. Make sure that the hydraulic track adjuster is thoroughly clean. Also, make sure that the
mounting surfaces are thoroughly clean.
2. Push the piston of track adjuster (2) into the cylinder assembly by hand. Push the piston into
the cylinder as far as possible.
1/3
2020/1/14

Caterpillar Cat 308ECR Mini Hydraulic Excavator (Prefix HAM) Service Repair Manual (HAM00001 and up).pdf

Recommended

Recommended

More Related Content

More from itj79143591

More from itj79143591 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 308ECR Mini Hydraulic Excavator (Prefix HAM) Service Repair Manual (HAM00001 and up).pdf