Published patent and design registration information january 30th, 2015

The Patent Office Journal 30/01/2015 22188
पेटेंट कायालय
शासक य जनल
OFFICIAL JOURNAL
OF
THE PATENT OFFICE
िनगमन सं. 05/2015 शुबवार दनांक: 30/01/2015
ISSUE NO. 05/2015 FRIDAY DATE: 30/01/2015
पेटेंट कायालय का एक ूकाशन
PUBLICATION OF THE PATENT OFFICE

INTRODUCTION
In view of the recent amendment made in the Patents Act, 1970 by the Patents (Amendment) Act, 2005
effective from 01st
January 2005, the Official Journal of The Patent Office is required to be published under
the Statute. This Journal is being published on weekly basis on every Friday covering the various proceedings
on Patents as required according to the provision of Section 145 of the Patents Act 1970. All the enquiries on
this Official Journal and other information as required by the public should be addressed to the Controller
General of Patents, Designs & Trade Marks. Suggestions and comments are requested from all quarters so that
the content can be enriched.
(Chaitanya Prasad)
CONTROLLER GENERAL OF PATENTS, DESIGNS & TRADE MARKS
30th
JANUARY, 2015

CONTENTS
SUBJECT PAGE NUMBER
JURISDICTION : 22191 – 22192
SPECIAL NOTICE : 22193 – 22194
EARLY PUBLICATION (DELHI) : 22195 – 22199
EARLY PUBLICATION (MUMBAI) : 22200 – 22208
EARLY PUBLICATION (CHENNAI) : 22209 – 22222
PUBLICATION AFTER 18 MONTHS (DELHI) : 22223 – 22872
PUBLICATION AFTER 18 MONTHS (MUMBAI) : 22873 – 22941
PUBLICATION AFTER 18 MONTHS (CHENNAI) : 22942 – 23039
PUBLICATION AFTER 18 MONTHS (KOLKATA) : 23040 – 23065
PUBLICATION UNDER SECTION 43(2) IN RESPECT OF
THE GRANT (DELHI) : 23066 – 23068
THE GRANT (MUMBAI) : 23069 – 23070
THE GRANT (CHENNAI)
: 23071 – 23073
THE GRANT (KOLKATA)
: 23074 – 23077
INTRODUCTION TO DESIGN PUBLICATION : 23078
THE DESIGNS ACT 2000 SECTION 30 DESIGN
ASSIGNMENT : 23079
COPYRIGHT PUBLICATION : 23080
RESTORATION OF LAPSED DESIGNS UNDER SECTION
12 (2) OF THE DESIGNS ACT, 2000 : 23081
REGISTRATION OF DESIGNS : 23082 - 23137

THE PATENT OFFICE
KOLKATA, 30/01/2015
Address of the Patent Offices/Jurisdictions
The following are addresses of all the Patent Offices located at different places having their Territorial
Jurisdiction on a Zonal basis as shown below:-
1 Office of the Controller General of Patents,
Designs & Trade Marks,
Boudhik Sampada Bhavan,
Near Antop Hill Post Office,S.M.Road,Antop Hill,
Mumbai – 400 037
Phone: (91)(22) 24123311,
Fax : (91)(22) 24123322
E-mail: cgpdtm@nic.in
4 The Patent Office,
Government of India,
Intellectual Property Rights Building,
G.S.T. Road, Guindy,
Chennai – 600 032.
Phone: (91)(44) 2250 2081-84
Fax : (91)(44) 2250 2066
E-mail: chennai-patent@nic.in
The States of Andhra Pradesh, Karnataka,
Kerala, Tamil Nadu and the Union
Territories of Puducherry and Lakshadweep.
Near Antop Hill Post Office,S.M.Road,Antop Hill,
Mumbai – 400 037
Phone: (91)(22) 24137701
Fax: (91)(22) 24130387
E-mail: mumbai-patent@nic.in
The States of Gujarat, Maharashtra, Madhya
Pradesh, Goa and Chhattisgarh and the Union
Territories of Daman and Diu & Dadra and Nagar
Haveli
Plot No. 32., Sector-14, Dwarka,
New Delhi – 110075
Phone: (91)(11) 2808 1921 – 25
Fax: (91)(11) 2808 1920 & 2808 1940
E.mail: delhi-patent@nic.in
The States of Haryana, Himachal Pradesh, Jammu
and Kashmir, Punjab, Rajasthan, Uttar Pradesh,
Uttaranchal, Delhi and the Union Territory of
Chandigarh.
5 The Patent Office (Head Office),
CP-2, Sector –V, Salt Lake City,
Kolkata- 700 091
Phone: (91)(33) 2367 1943/44/45/46/87
Fax: (91)(33) 2367 1988
E-Mail: kolkata-patent@nic.in
Rest of India
Website: www.ipindia.nic.in
www.patentoffice.nic.in
All applications, notices, statements or other documents or any fees required by the Patents Act, 1970
and The Patents (Amendment) Act, 2005 or by the Patents (Amendment) Rules, 2006 will be received
only at the appropriate offices of the Patent Office.
Fees: The Fees may either be paid in cash or may be sent by Bank Draft or Cheques payable to the Controller of
Patents drawn on a scheduled Bank at the place where the appropriate office is situated.

पेटेंट कायालय
कोलकाता, दनांक 30/01/2015
कायालय के ेऽािधकार के पतेê
विभ न जगह पर ःथत पेटेंट कायालय के पते आंचिलक आधार पर दिशत उनके ूादेिशक अिधकार ेऽ के
साथ नीचे दए गए है:-
1 कायालय : महािनयंऽक, एकःव, अिभक प
तथा यापार िचहन,
एंटोप हल डाकघर के समीप,
एस. एम. रोड, एंटोप हल, मु बई- 400 037, भारत,
फोन: (91) (22) 24123311
फ़ै स: (91) (22) 24123322
ई. मेल: cgpdtm@nic.in
4 पेटेंट कायालय, भारत सरकार
इंटेले चुअल ूॉपट राइ स ब डंग, इंड ःशयल इःटेट
एसआईड सीओ आरएमड गोडाउन ए रया
एडजसे ट टु ईगल लाःक, जी. एस. ट . रोड, गाय ड
चे नई - 600 032.
फोन: (91)(44) 2250 2081-84
फ़ै स: (91)(44) 2250-2066
ई. मेल: chennai-patent@nic.in
आ ी ूदेश, कनाटक, के रल, तिमलनाडु तथा
पुडचेरु रा य ेऽ एवं संघ शािसत ेऽ, ल द प
बौ क संपदा भवन,
एंटोप हल डाकघर के समीप,
एस. एम. रोड, एंटोप हल, मु बई- 400 037,
फोन: (91) (22) 24137701
फ़ै स: (91) (22) 24130387
ई. मेल: Mumbai-patent@nic.in
गुजरात, महारा , म य ूदेश, गोवा तथा छ ीसगढ़
रा य ेऽ एवं संघ शािसत ेऽ, दमन तथा द व,
दादर और नगर हवेली.
लॉट सं. 32, से टर- 14, ारका, नई द ली- 110 075.
फोन: (91)(11) 2808 1921-25
फ़ै स: (91)(11) 2808 1920, 2808 1940
ई. मेल: delhi-patent@nic.in
ह रयाणा, हमाचल ूदेश, ज मू तथा कँमीर,
पंजाब,राजःथान, उ र ूदेश, द ली तथा उ रांचल रा य
ेऽ , एवं संघ शािसत ेऽ चंड गढ़
कोलकाता, (ूधान कायालय)
सीपी-2, से टर- V, सा ट लेक िसट ,
कोलकाता-700 091, भारत.
फोन: (91)(33) 2367 1943/44/45/46/87
फ़ै स:/Fax: (91)(33) 2367 1988
ई. मेल: kolkata-patent@nic.in
भारत का अवशेष ेऽ
वेबसाइट: http://www.ipindia.nic.in
www.patentoffice.nic.in
पेटेंट अिधिनयम, 1970 तथा पेटेंट (संशोधन) अिधिनयम, 2005 अथवा पेटेंट (संशोधन) िनयम, 2006 ारा वांिछत सभी आवेदन,
सूचनाए, ववरण या अ य दःतावेज़ या कोई शु क पेटेंट कायालय के के वल उपयु कायालय में ःवीकृ त ह गे।
शु क: शु क या तो नगद प में या Controller of Patents के नाम में देय बक सा ट या चेक के ारा भेजी जा सकती है जो उसी ःथान के
कसी अनुसूिचत बक में ूद हो जहाँ उपयु कायालय ःथत है ।

SPECIAL NOTICE
18 Months publication as required under Section 11A of the Patents Act, 1970
as amended by the Patents (Amendment) Act, 2005.
Notice is hereby given that any person at any time before the grant of Patent may give representation by way of
opposition to the Controller of Patents at appropriate office on the ground and in a manner specified under
section 25(1) of the Patents (Amendment) Act, 2005 read with Rule 55 of the Patents (Amendment) Rules,
2006.
Notice is also given that if any interested person requests for copies of the complete specification, drawing and
abstract of any application already published, the photocopy of the same can be supplied by the Patent Office as
per the jurisdiction on payment of prescribed fees of Rs.8/- per page. If any further details are required to be
obtained, the same can be provided by the respective Patent Offices on request.
(Chaitanya Prasad)
CONTROLLER GENERAL OF PATENTS, DESIGNS & TRADE MARKS

SPECIAL NOTICE
Under the new provision of the Patents Act, 1970 as amended by the Patents (Amendment) Act, 2005
and Rules there under, Publication of the matter relating to Patents in the Official Gazette of India Part III,
Section 2 has been discontinued and instead The Official Journal of the Patent Office is being published
containing all the activities of The Patent Office such as publication of all the patent applications after 18th
months , grant of patents & all other information in respect of the proceedings as required under the provisions
of the Patents (Amendment) Act, 2005 and Rules thereunder on weekly basis on every Friday.
The Journal is uploaded in the website every Friday. So Paper form and CD-ROM form of the Journal are
discontinued from 01/01/2009.
SPECIAL NOTICE
Every effort is being taken to publish all the patent applications under section 11(A) of the Patents Act.
However, if duplication of publication of any application is found, then earlier date of publication will be taken
for the purpose of provisional protection for applicant and Patent Office will grant Patent not before six months
from the date of second publication, provided that there is there is no third party representation.

Early Publication:
The following patent applications have been published under section 11A (2) of The Patents (Amendment) Act 2005 and rule
24A of The Patents (Amendment) Rules, 2006. Any person may file representation by way of opposition to the Controller of
Patents at the appropriate office against the grant of the patent in the prescribed manner under section 25(1) of the Patents
(Amendment) Act 2005 read with the rule 55 of The Patents (Amendment) Rules, 2006:
(12) PATENT APPLICATION PUBLICATION (21) Application No.2717/DEL/2013 A
(19) INDIA
(22) Date of filing of Application :17/09/2013 (43) Publication Date : 30/01/2015
(54) Title of the invention : UNIVERSAL BLOCK INSTRUMENT (FOR RAILWAY ABSOLUTE BLOCK SYSTEM)
(51) International classification
:B61L,
B61F
(31) Priority Document No :NA
(32) Priority Date :NA
(33) Name of priority country :NA
(86) International Application No
Filing Date
:NA
:NA
(87) International Publication No : NA
(61) Patent of Addition to Application Number
Filing Date
:NA
:NA
(62) Divisional to Application Number
Filing Date
:NA
:NA
(71)Name of Applicant :
1)JAGDISH CHANDER PANERI
Address of Applicant :215-GANESH COLONY, RAOJI-KA
HATA, UDAIPUR-313001. Rajasthan India
(72)Name of Inventor :
1)JAGDISH CHANDER PANERI
(57) Abstract :
Universal block instrument is Railway Electrification clear means this Universal Block Instrument will prevent from induce effect of
AC high voltage.
No. of Pages : 14 No. of Claims : 10

(19) INDIA
(54) Title of the invention : SYSTEM AND METHOD FOR FACILITATING DIAGNOSTIC AND MAINTENANCE OF A
MEDICAL DEVICE
(51) International classification :A61B6/00
Filing Date
:PCT//
:01/01/1900
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)HCL Technologies Ltd.
Address of Applicant :B-39, Sector 1, Noida 201301, Uttar
Pradesh, India
1)BARUAH, Shantanu
2)SETHI, Rohit
(57) Abstract :
Disclosed is a system for facilitating diagnostic and maintenance of a medical device used for treatment of a patient. The system
comprises a data capturing module for capturing data pertaining to a medical device. The data may be captured from one or more data
sources comprising Picture Archiving and Communication System (PACS), Electronic Medical Record (EMR) systems, and Device
Monitoring System. Further, the system comprises an analysis module for deriving meaningful information from the data by
performing data analytics on the data. Further, the system comprises a prediction module for predicting insights associated to the
medical device based on the meaningful information, wherein the insights facilitate in diagnosis and maintenance of the medical
device.

(12) PATENT APPLICATION PUBLICATION (21) Application No.311/DELNP/2015 A
(19) INDIA
(54) Title of the invention : METHOD AND DEVICE FOR MEASURING LEVELS OF CAST IRON AND SLAG IN A BLAST
FURNACE
(51) International
classification
:B22D 2/00,
G01F23/22,G01F23/14,B22D11/18
(31) Priority Document No :2012/0493
(32) Priority Date :13/07/2012
(33) Name of priority country :Belgium
(86) International Application
No
Filing Date
:PCT/EP2013/064482
:09/07/2013
(87) International Publication
No
:WO 2014/009367
(61) Patent of Addition to
Application Number
Filing Date
:NA
:NA
(62) Divisional to Application
Number
Filing Date
:NA
:NA
1)CENTRE DE RECHERCHES M‰TALLURGIQUES
ASBL CENTRUM VOOR RESEARCH IN DE
METALLURGIE VZW
Address of Applicant :Boulevard de la Plaine 5 B 1050
Bruxelles Belgium
1)OJEDA ARROYO Claudio
2)DURIEU Frdric
3)ESSER Eric
(57) Abstract :
The present invention relates to a method for measuring the liquid metal surface level (13) and the slag surface level (14) in the
crucible (1) of a metallurgical shaft furnace comprising the following steps: measuring at one or more points on the external wall (2)
of the crucible the following variables: the circumferential strain in said external wall (2) by means of a number of strain gauge
sensors (6) fixed to the armour (4) of the external wall (2) of the crucible; and the temperature of said external wall (2) by means of
one or more temperature sensors (7) fixed to the armour (4) of the external wall (2) of the crucible; introducing said variables
measured at a number of points on the external wall of the crucible into the general equation governing circumferential strain the
solution of which is analytical and which contains two unknowns the liquid metal level and the overall liquid metal/slag
level considering set parameters; and solving said equation and obtaining an analytical solution giving the liquid metal surface level
(13) and the slag surface level (14) in the crucible (1).

(19) INDIA
(54) Title of the invention : ROTATIONAL ENERGY BY GRAVITATIONAL FORCE
:F03G,
F03B
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)JAIPARKASH
Address of Applicant :JAIPARKASH S/O LATE SH. LAL
SINGH VILLAGE-ALIPUR TEHSIL-SARDHANA DISTT.
MEERUT Uttar Pradesh India
1)JAIPARKASH
(57) Abstract :
The present invention relates to a system for generating rotational energy comprising a frame having a plurality of shafts, each of
which is tied with a rope, other end of which is attached to a divided weight supported on a fixed weight, which is connected to
another fxed weight to generate rotational energy. It is associated with the following advantageous features:- - Cost effective. -
Compact. - No Air Pollution. - Less maintenance.

(19) INDIA
(54) Title of the invention : SELF SIMILARITY MEASURE FOR FRAUD MEASUREMENT
:G07G
1/14
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SAS INSTITUTE INC.
Address of Applicant :100 SAS CAMPUS DRIVE, CARY,
NORTH CAROLINA 27513, U.S.A.
1)BRIAN DUKE
2)MEHMET KEREM MUEZZINOGLU
3)ANKUR GUPTA
(57) Abstract :
A computerized system that processes a fraud score for a financial transaction in connection with an account is computed from
retrieved data to indicate a probability of the account being in a compromised condition. A self-similarity score is computed if the
computed fraud score is above a predetermined threshold to indicate similarity of the received transaction to other transactions of the
account in the set of prior transactions. A suggested action to authorize or decline the transaction is determined based on the computed
fraud score and the computed self-similarity score.

(12) PATENT APPLICATION PUBLICATION (21) Application No.1094/MUM/2014 A
(19) INDIA
(54) Title of the invention : A LATCH ARRANGEMENT FOR MOTORIZED OPERATING MECHANISM OF CIRCUIT
BREAKER
:H01H71/50,
H01H71/52
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)LARSEN & TOUBRO LIMITED
Address of Applicant :L & T House, Ballard Estate, P.O. Box
278, Mumbai 400 001, State of Maharashtra, India
1)AMBEKAR, Mandar, M.
2)MURUKATE, Mohan, K.
(57) Abstract :
The present invention relates to a stored energy operating mechanism used in circuit breaker for switchgear products. The present
invention provides a motorized operating mechanism of circuit breaker with dynamic latch arrangement to assist positive closing of
the circuit breaker during its reverse travel. This will allow breaker even with toggle point occurring late to be used with motorized
operating mechanism and ensure positive closing of breaker. In the present invention, latch arrangement operates on centrifugal force
phenomenon; hence it can be worked with any mounting position of circuit breaker without getting affected by gravity.

(19) INDIA
(54) Title of the invention : DESIGN OF EQUIPMENT FOR GAS-GAS, GAS-SOLID AND GAS-SOLID-GAS REACTIONS.
:B01J
19/00,
D01B1/02
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)TUNGIKAR VINOD BALWANTRAO
Address of Applicant :DEPARTMENT OF PRODUCTION
ENGINEERING, SGGS INSTITUTE OF ENGINEERING AND
TECHNOLOGY, NANDED-431606, MAHARASHTRA,
(INDIA)
1)TUMME PRATIK R
2)TUNGIKAR VINOD B
(57) Abstract :
At present, numerous equipments are followed for reaction kinetics. The primary aim of an industry requires minimum cost equipment
and minimum area. To check the feasibility of the equipment, I carried out experiment of cottonseed delinting. This equipment fulfills
the requirements of industry and is not limited to delinting of cottonseed rather it can be used in many gas-gas, gas-solid and gas-
solid-gas reactions.

(19) INDIA
(54) Title of the invention : SYNTHESIS OF NOVEL 3-(2-CHLOROQUINOLIN-3-YL)-N-CYCLOHEXYLQUINOXALIN-2-
AMINES AND ANTIBACTERIAL ACTIVITY THEREOF
:C07D
471/04
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)JAIPRAKASH N. SANGSHETTI
Address of Applicant :Y. B. CHAVAN COLLEGE OF
PHARMACY, DR. RAFIQ ZAKARIA CAMPUS, RAUZA
BAGH, AURANGABAD 431001, MAHARASHTRA, INDIA.
1)JAIPRAKASH N. SANGSHETTI
2)FIROZ A. KALAM KHAN
3)DEVANAND B. SHINDE
4)ZAHID ZAHEER
5)INDRAJEET GONJARI
6)ROHIDAS AROTE
7)RAJENDRA H. PATIL
(57) Abstract :
The present invention relates to a synthesis of novel 3-(2-chloroquinolin-3-yl)-N-cyclohexylquinoxalin-2-amines and antibacterial
activity thereof. A process for producing a compound of the formula (JF) Wherein R1 represents a hydrogen atom, a nitro group, a
chlorine atom or a methyl group, and R2 represents a hydrogen atom, a methyl group or.a methoxyl group. which comprises step 1 of
reacting a compound of the formula (1) in the presence of acetic anhydride (Ac20), glacial acetic acid (AcOH) and sodium acetate
(NaOAc) to obtain a compound of the formula (2); Wherein R2 has the same meaning as defined above, which comprises, step 2 of
reacting the compound of formula (2) obtained in the step 1 and phosphoryl chloride (POCI3) in presence of N,N-dimethylformamide
(DMF) to obtain the compound of the formula (3). Wherein R2 has the same meaning as defined above, Wherein R1 and R2 have the
same meaning as defined above. and which comprises, step 3 of reacting the compound of formula (3) obtained in the step 2,
compound of formula (4) and compound of formula (5) in presence of ethanol (EtOH) using ceric ammonium nitrate (CAN) as
catalyst to obtain the compound of the formula (JF).

(19) INDIA
(54) Title of the invention : NOVEL POLY(ESTER-AMIDE) HOT MELT ADHESIVE USING RICINOLEIC ACID
:C08G
18/60,
C09J
177/12
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)MHASKE SHASHANK TEJRAO
Address of Applicant :DEPARTMENT OF POLYMER AND
SURFACE ENGINEERING, INSTITUTE OF CHEMICAL
TECHNOLOGY, NATHALAL PAREKH MARG, MATUNGA
(EAST), MUMBAI-400019, MAHARASHTRA, INDIA.,
1)KADAM PRAVIN GOPAL
2)VAIDYA PARTH NITIN
3)SAVVASHE PRASHANT BHAIRAVNATH
(57) Abstract :
In the present invention, novel poly(ester-amide) hot melt adhesives are prepared from condensation of sebacic acid with the
equivalent proportion of a mixture of ricinoleic acid and ethylenediamine.

(19) INDIA
(54) Title of the invention : DESIGN OF RAILWAY PLATFORM SHED WITH TRUSSLESS ROOF.
(51) International classification :B61D15/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SATISH NAGORAO MOWADE
Address of Applicant :402/03, UTKARSH RAJNIGANDHA
KHARE TOWN NAGPUR-10 Maharashtra India
1)SATISH NAGORAO MOWADE
(57) Abstract :
This is an innovative platform shed that can change the current Indian railway platform scenario which is of safe, economical, truss
less (Without purlins) and maintenance free railway platform shed. It is an attractive architectural conceptual design with enough
structural stability to withstand all the applied loads. Application of this shed may change the total scenario of Indian railway
platforms. The whole structure is rested on a single RCC column (spacing of two RCC column is 8 m) and the girder above column is
supported at its center by the column. Other two ends are cantilever. Total girder length is 9.90 m as per railway standards whereas the
cantilever part will be nearly 4.5 m on each side. Galvalume sheet (trussless roof) will rest on a runner beam which is fixed at the
cantilevered edge of girder. This runner beam will transfer all the loads on the girder. An arrangement of proper gutter is made for
proper drainage without disturbing any movement on railway platform. This shed is successfully erected on railway platform of
Nagpur railway station (India). It has proved its stability in a cyclone dated on 23rd Feb 2014 in Nagpur territory. As a case study we
will deal with the details.

(19) INDIA
(54) Title of the invention : ELECTRO-PNEUMATIC LAMP
:B60T17/22,
B60T17/18
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SAUMYA JAY DHOLAKIA
Address of Applicant :7, UDAY HEIGHTS, PLOT NO. H4
ADC, SECTOR NO. 26, NEAR AKURDI RLY STATION, B/H
KENDRIYA SADAN, PRADHIKARAN, NIGDI, PUNE 411
044, MAHARASHTRA, INDIA
1)SAUMYA JAY DHOLAKIA
(57) Abstract :
A system for generating electricity for small scale applications by physical means, the said system uses a bellow foot pump that
operates on foot pressure to generate sufficient amount of compressed air, the said pump then operates an air motor of required torque,
the said motor then operates a dynamo used to generate sufficient amount of electricity to power the LEDs, the said dynamo is then
connected to a small portable battery through a switch, the said switch if closed connects the dynamo to the battery and if opened
connects the dynamo directly to the LED, the said LED can then provide sufficient amount of light for the given application.

(19) INDIA
(54) Title of the invention : UTILIZATION OF COAL FLY ASH OF THERMAL POWER PLANT IN CONJUNCTION WITH
CHITOSAN FOR EFFICIENT REMOVAL OF DIFFERENT HEAVY METAL IONS AND THEIR SOLIDIFICATION FOR SAFE
SOLID WASTE DISPOSAL.
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AGARWAL, AJAY KUMAR
Address of Applicant :10, SHIRISH APARTMENTS,
SHASTRI LAYOUT, JAITALA ROAD, SUBHASH NAGAR,
NAGPUR-440022 Maharashtra India
1)AGARWAL, AJAY KUMAR
2)DR. KADU, MAHENDA S.
3)DR. PANDHURNEKAR, CHANDRASHEKHAR P.
4)MUTHREJA, ISHWARDAS L.
(57) Abstract :
In our present invention, the study was undertaken to investigate the removal efficiency of different metal ions such as Ni++, Zn and
Pbions from the aqueous solution in economical and environmental friendly way. For the first time, a mixture consisting of thermal
power waste i.e. fly ash along with chitosan, a kind of bioadsorbant was used to remove these heavy metal ions from the aqueous
solution. It was observed that the removal efficiency of Znand Pb++ions from the aqueous solution was 100%, whereas Ni1 ions
within the range of 88.08 -50.49%. During these batch studies, the mixture pH was maintained at 8.5 pH and the solution was under
constant stirring condition. In this process fly ash was used without any pre-treated. The waste produced from this process is fly ash
and bio-sorbent containing Ni, Zn and Pbions, when solidified with the Portland cement doesnt leach out the Zn++and Pbions even
after 90 days of leaching test.However, a small traces of Ni1-1 ions were leach out, but their accumulated concentration was found be
very low as compared to the limits given by The Environment (Protection) Rules, 1986, Schedule - VI, India.Therefore, this proves
the fact that the process invented is helpful to remove heavy metal contamination from waste water and the waste produced from the
process can be disposed off in environmental friendly manner after solidifying it with the cement.

(19) INDIA
(54) Title of the invention : NOVEL POLY(ESTER-AMIDE) HOT MELT ADHESIVE USING CASTOR OIL
:C08G
18/60,
C09J
177/12
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Address of Applicant :DEPARTMENT OF POLYMER AND
SURFACE ENGINEERING, INSTITUTE OF CHEMICAL
TECHNOLOGY NATHALAL PAREKH MARG, MATUNGA
(EAST), MUMBAI 400019, MAHARASHTRA, INDIA.
1)KADAM PRAVIN GOPAL
2)VAIDYA PARTH NITIN
3)SAVVASHE PRASHANT BHAIRAVNATH
(57) Abstract :
In the present invention, novel poly(ester-amide) hot melt adhesives are prepared from condensation of sebacic acid with the
equivalent proportion of a mixture of castor oil and ethylenediamine.

(19) INDIA
(54) Title of the invention : MICRO-CONTROLLER BASED AUTOMATED JIG & FIXTURE FOR CURVED SURFACE
DRILLING WITH INDEXING ATTACHMENT.
:E21B7/00,
E21B44/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)TUNGIKAR VINOD BALWANTRAO
Address of Applicant :DEPARTMENT OF PRODUCTION
ENGINEERING, SGGS, INSTITUTE OF ENGINEERING AND
TECHNOLOGY, VISHNUPURI, NANDED-431 606,
MAHARASHTRA, INDIA.
1)ABHALE NILESH S
2)PATIL SAGAR G
3)TUNGIKAR VINOD B
(57) Abstract :
A system and method of drilling on a surface comprising an indexing rod, an indexing plate, at least one locating element, plurality of
clamping units, at least one microcontroller, a motor and a locking mechanism. The method of drilling includes, withdrawing the
indexing pin from the indexing plate to unlock rotary movement of the indexing rod. A first signal is sent to the stepper motor from
the microcontroller to rotate the indexing rod at the desired angle. Subsequently a second signal is sent to the stepper motor from the
microcontroller to stop the stepper motor when the indexing rod reaches the desired angle. This rotation of the indexing rod rotates the
workpiece to the angle where a hole has to be drilled. The rotary motion of the indexing rod is then locked by inserting the indexing
pin in a indexing hole of the indexing plate.

(12) PATENT APPLICATION PUBLICATION (21) Application No.33/CHE/2015 A
(19) INDIA
(54) Title of the invention : LEUKOCYTE ESTERASE DETECTION FROM THROAT SWAB
(51) International classification :C12Q
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Kumara Venkatanarayana Nibhanipudi
Address of Applicant :H. No. 150/A SRT, Sanjeeva Reddy
Nagar, Hyderabad, Telangana, India.
(57) Abstract :
The present invention relates to the field of infectious diseases. The invention specifically relates to the diagnostic test for acute
bacterial pharyngitis. The test is used in screening for Group A Beta Haemolytic Streptococcus by the identifying the presence of
leukocyte esterase in the throat. The Leukocyte Esterase Throat Swab Test is compared to the Rapid Step Test for efficiency in terms
of fast delivery of results.

(19) INDIA
(54) Title of the invention : METHOD AND SYSTEM FOR DETECTING A SECURITY BREACH IN AN ORGANIZATION
(51) International classification :g06q
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)WIPRO LIMITED
Address of Applicant :Doddakannelli, Sarjapur Road,
Bangalore 560035, Karnataka, India.
1)ABHISHEK SUMAN
2)SREEVIDYA KHATRAVATH
3)MANIKHANTAN SANKARA RAMAN
(57) Abstract :
Embodiments of the present disclosure disclose a method and a system for detecting a breach of security in an organization. The
method comprises receiving input data in real-time from one or more security systems. The method further comprises analyzing the
input data to generate at least one of security information in a predefined format, trajectory information on movement of one or more
persons, and facial features of the one or more persons. The method further comprises correlating the security information, the
trajectory information and the facial features. The method further comprises detecting the security breach in the organization based on
the correlation.

(19) INDIA
(54) Title of the invention : POWER FROM GRAVITATIONAL PRESSURE VARIATION SYSTEM (PGPV SYSTEM)
(51) International classification :f03d
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)V.M. KRISHNA KUMAR
Address of Applicant :VETTUKATTIL HOUSE,
KALIYAROAD POST, CHELAKKARA, THRISSUR - 680 586
Kerala India
1)V.M. KRISHNA KUMAR
(57) Abstract :
A system for power generation, mainly electric power based on gravitational pressure variation, wherein no use of fuel or any kind of
external energy like sunlight, wind etc. Uninterrupted power is generated, free from pollution and other environmental issues, with
very low cost of production, which enables in distributing energy everywhere irrespective of time and distance, as it can be
commissioned anywhere.

(19) INDIA
(54) Title of the invention : AN IMPROVISED ELECTRIC SCOOTER WITH REDESIGNED BODY AND FRAME SIMULATING
THE SWAN
(51) International classification :b62k
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ANOOP NISHANTH P.J
Address of Applicant :NO.5, GOVINDASWAMY NAGAR,
JUMBLI NEW COLONY, KODINGAIYUR, CHENNAI -
600118 Tamil Nadu India
1)ANOOP NISHANTH P.J
(57) Abstract :
The present invention discloses an electric scooter having a body that is designed from the inspiration of a swan for providing efficient
air flow during the ride. The electric bike comprises a water proof BLDC motor (2), a deck configured to support the rider, front and
back wheel base and chassis, controllers (1) placed within the wheel base under the foot rest of the driver for providing the scooters
information to the driver. The electric scooter comprises one or more rechargeable and removable concealed battery packs (3)
supplying the required power of 48V and 50 - 120A to the driving force of the scooter along with an anti-lock brake, a dual suspension
and integrated brake and throttle control. The electric scooter design thus has the powering lithium ion/l_ifepo4/Lithium polymer
electric batteries (3) mounted in a concealed under body position relative to the platform giving the swan shaped electric scooter a low
center of gravity with optimal riding profile. The electric scooter is designed based on the body shape of the bird swan in order to
provide a swift movement to the scooter with minimal air resistance. The rear wheel assembly includes a belt drive mechanism (5) for
transferring the power from the motor (2) to the wheel base through a swing arm (4) and for forward motion and free wheel coasting.
This improved electric motor scooter thus includes: a front lower frame; a front wheel assembly coupled to the front frame and
residing on a surface; a rear upper frame; a back wheel assembly coupled to the rear frame and residing on the surface; and a center
pivot mechanism comprising the controllers, motor, concealed batteries coupled to the front frame and the rear frame all designed in
the .shape of a swan. .

(19) INDIA
(54) Title of the invention : BLUE TOOTH IGNITION AND IDENTIFICATION OF TWO WHEELERS
(51) International classification :H04W
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SUDHAKAR
Address of Applicant :37, VINAYAGAR KOIL STREET,
SOKKANATHANPET - 605 009 Pondicherry India
2)VIJAYAKUMAR
1)SUDHAKAR
2)VIJAYAKUMAR
(57) Abstract :
The invention discloses an application of Bluetooth in two wheeler motor vehicles and an ignition and identification system thereof,
comprising the following steps: the master unit of Bluetooth of the two wheeler motor vehicle owner initiates a master/slave
connection by an android mobile and the slave unit of Bluetooth arranged in the two wheeler motor vehicle to control the ignition of
the engine, indicators and horn. The slave unit of Bluetooth of the vehicle is identified by the android phone of the owner. The safe
mode link for pairing of this slave Bluetooth module and the android phone occurs. After successful pairing with the slave Bluetooth
module, the owner or user can send command to the slave Bluetooth module using the application provided in the android phone using
terminal Bluetooth. When the slave Bluetooth module fixed in the vehicle identifies the command send in by the owner then it sends
out signal to control the ignition switch, indicators and the horn of the vehicle. The invention applies Bluetooth to the control of the
ignition switch, indicators and horn of the vehicle by an android mobile compared with common wireless control ignition, the
invention greatly enhances the security of two wheelers.

(19) INDIA
(54) Title of the invention : METHOD AND SYSTEM FOR MANAGING TUNERS OF CLIENT DEVICES
(51) International classification :H04n
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)WIPRO LIMITED
Address of Applicant :Doddakannelli, Sarjapur Road,
Bangalore 560035, Karnataka, India.
1)GOWRISHANKAR SUBRAMANIAM NATARAJAN
2)HARISH NAIR RAJAGOPAL
(57) Abstract :
The present disclosure relates to a method and a system for managing tuners of client devices. In one embodiment, a request to
allocate a tuner for recording or playback of a broadcast program is received by one or more recording devices from one or more
client devices. The system determines states and available recording space of one or more tuners associated with the client devices.
The system also determines business rules associated with the client devices based on state, available recording space and type of
request received. Based on the business rules, the system identifies a tuner to service the request and allocate the tuner to service the
request of the client devices. Thus the system provides multiple device tuner management by identifying and assigning a tuner
appropriate to service the request from client device and also identifies the correct tuner with appropriate storage space available to
service the request.

(19) INDIA
(54) Title of the invention : METHOD FOR MANUFACTURING A SEAMLESS COPPER CONTAINER BY SPINNING
PROCESS
(51) International classification :D01d
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)THOKALA SRINIVAS REDDY
Address of Applicant :H. No. 8-1-168/1, Pragathi Colony,
Maillardevpally, Rajendranagar, Hyderabad-500005, Telangana,
India.
2)THOKALA SRISAILAM REDDY
1)THOKALA SRINIVAS REDDY
2)THOKALA SRISAILAM REDDY
(57) Abstract :
Exemplary embodiments of the present disclosure are directed towards a method for manufacturing a seamless copper container by
spinning process. The method comprising deep drawing a copper circle to form a non uniformed piece of copper, positioning the non
uniformed piece of copper on a spinning machine to form a uniformed piece of copper comprising a hallow body, and positioning the
uniformed piece of copper comprising a hallow body on a die comprising a predefined shape for forming a container of a preferred
geometrical shape.

(19) INDIA
(54) Title of the invention : SYSTEM AND METHOD FOR CONVERTING THE BUSINESS PROCESSES TO TEST-CENTRIC
ACTIVITY DIAGRAMS
(51) International classification :G06F
(33) Name of priority country :U.S.A.
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)M/S CIGNITI TECHNOLOGIES LIMITED
Address of Applicant :SUITE NO. 106 & 107, 6-3-456/C,
MGR ESTATES, DWARAKAPURI COLONY, PUNJAGUTTA,
HYDERABAD-500 082 Andhra Pradesh India
1)RAJA SEKHAR NERAVATI
2)KALYANA RAO KONDA
(57) Abstract :
The system and method for conversion of a business process to test-centric activity diagrams and to computationally generate
automatic test suites for various quality attributes. It has been created to reduce the effort of a test engineer. The system consists of the
processor 1, the parsing module 2, the analysis module 3 and the test case generator 4. The method takes an activity diagram as the
input, which can be generated using UML or.any available standard business modelers and to be exported in the industry standard
XMI format. The method is pro-agile as it achieves almost 100% functional coverage and has negligible dependence on conventional
documentation. The method permits domain specialists and business analysts to add special, custom tags for specific validation
conditions and functional checks.

(19) INDIA
(54) Title of the invention : ROAD RUNNERS
(51) International classification :B60R
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)M. VARUN KUMAR
Address of Applicant :NO-77 BIG STREET, KARNAMBUT
VILLAGE, KATPADI TK, VELLORE DT, PIN-632519 Tamil
Nadu India
1)M. VARUN KUMAR
2)MANICKYAM KARTHIK
3)S. RAJESK KUMAR
4)P. RAJESH
5)S. ARJUN RAJ
6)M. VIJAYAKUMAR
(57) Abstract :
Under normal circumstances, any vehicle which runs through fiiel (LPG, Petrol and Diesel) can be traced with the help of GPS
technology. Through GPS device, navigation can be done for the drivers use and also we can trace the location details of the vehicle in
case of theft or hijack. Still now the technology was up to locating the vehicle through GPS while during vehicle theft or unauthorized
control of vehicle, but we cant stop the vehicle in the particular location where we trace. In order to tackle these kind of difficulties,
we are providing a very good solution by introducing a new GSM based technology. By means of this technology, a person whose
vehicle have been theft or unauthorized control, can stop his/her vehicle movement very soon by initially blocking the fuel supply to
the engine then later by blocking the ignition of the vehicle and finally by blocking the sensors associated to the vehicle just by
clicking a button STOP in the Road Runners android mobile application, so after secure authentication that Road Runners app sends
an command as SMS to the GSM device to make automated ON the road runners mechanism and after 1 minute of delay time it again
sends an command as SMS to GSM device of Road Runners mechanism connected to the Vehicle during Manufacture, while the
vehicle comes to complete dead stage after it get stopped due to simulated blockages made to the (fuel and ignition) vehicle. In turn
the vehicle owner will be Updated with an location SMS and the Road Runners APP facilitates the vehicle owner which contains the
exact address about the vehicle location were it get stopped.

(19) INDIA
(54) Title of the invention : LIGHT EMITTING DIODE AS A COGENERATION SOURCE (COGENERATION IRON BOX)
(51) International classification :H01l
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Safnil S
Address of Applicant :Ambrammel house, pathimangalam
Kunnamangalam p.o, Kozhikode (calicut), Kerala, India
2)Shreeganesh V Nair
1)Shreeganesh V Nair
2)Safnil S
(57) Abstract :
The present invention relates to a system of Cogeneration using Light Emitting Diode (LED). In one embodiment of the claimed
invention, the cogeneration Iron box utilizes the capability of the LED to produce useful heat and electrical energy simultaneously.
The useful heat is harnessed from the temperature of the activated pn junction and the electrical Energy is salvaged from the emitted
light using photovoltaic cells. This Iron Box produces sufficient heat to replace conventional Iron Boxes and produces sufficient
electrical energy to charge the on board battery. The arrangement of the cogeneration iron box comprises of a standard AC/ DC Driver
energizing a designed framework of LEDs fixed on a mounting plate. This arrangement is suitable for conducting heat from the LEDs
to a standard iron box plate using a heat conducting compound as the medium for controlling conductive heat loss. This arrangement
is provided with a photovoltaic cell assembly facing the lit side of the LEDs to generate electricity sufficient enough to charge the on
board battery.

(19) INDIA
(54) Title of the invention : TABLE TOP PORTABLE MINI FRICTION WELDING MACHINE FOR MINIATURE OF WELDED
JOINTS
(51) International classification :b23K
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR. P. MARIMUTHU
Address of Applicant :PRINCIPAL, SYED AMMAL
ENGINEERING COLLEGE, DR. E M. ABDULLAH CAMPUS,
RAMANATHAPURAM-623502 Tamil Nadu India
2)TTM. KANNAN
1)DR. P. MARIMUTHU
2)TTM. KANNAN
(57) Abstract :
Miniature of components with micro scaled features are increasingly required in many industries including automotive,Aeospace and
Biomedical.Mini machine is the foundation of technology to produce miniature of components with high accuracy requirements in 3
dimensional features. Modern Techniques are available with wider applications in the design of small structures and models for actual
machines that are made from appropriate materials. Table top mini friction welding machine is a specially designed machine for
Welding of miniature of welded joints such as aluminium, copper, composite and plastic cylindrical rods.Fricton welding is a solid
state welding which produce heat by conversion of Mechanical energy into Thermal energy at the interface of work during rotation
under pressure. This Table top mini welding machine will perform accuracy with compromising welding tolerance. It leads to save
energy, space and other basic requirements. High precision axis of motion, high loop stiffness, and good damping capacity with low
vibrations, low power consumption and portable are main features of Table top mini friction welding machine. It is the first step to
fabricate the Table top mini friction welding machine for small weld joints of similar and dissimilar materials in concept of small
machines for small components. This table top mini welding machine will satisfy the real requirements friction welding process. The
various performance tests were conducted to optimize the machine. It will be handled by any one, anytime and anywhere without
much effort.

(19) INDIA
(54) Title of the invention : DOUBLE SOFT COLLAR
(51) International classification :A61F
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Address of Applicant :H. No. 150/A SRT, Sanjeeva Reddy
Nagar, Hyderabad, Telangana, India.
(57) Abstract :
The present invention relates to medical devices in the field of Emergency and Intensive Care Medicine. The present invention
particularly discloses the method of use of the double soft cervical collar. The present invention also particularly relates to the
usefulness of double soft cervical collar over hard (Philadelphia collar) and soft cervical collars.

(19) INDIA
(54) Title of the invention : METHOD AND SYSTEM FOR PROCESSING SECRET INPUT TEXT STEGANOGRAPHICALLY
TO HIDE SECRET INPUT TEXT
(51) International classification :h04N
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR KALAVATHI ALLA
Address of Applicant :D.NO 11-843/3, 1/1 PATTABHI
SITARAM NAGAR, NAGARALU, AMARAVATHI ROAD,
GUNTUR Andhra Pradesh India
1)DR KALAVATHI ALLA
(57) Abstract :
The present invention describes a method and a device for processing a secret input text steganographically to hide the secret input
text within a Devanagari script based text. The device is configured to perform encoding of the secret text into a first encoding pattern
based upon a pre-determined criteria; encoding of a Devanagri script based cover text to a second encoding pattern based upon a
criteria selected out of a plurality of Devanagri text encoding criterion; mapping the second encoding pattern with first encoding
pattern to determine a degree of match; and embedding said input text within the said Devnagari script based cover text based upon
the selected criteria to produce a steganographic text based upon the degree of match exceeding a threshold. The steganographic so
produced text is textually identical to said cover text.

(19) INDIA
(54) Title of the invention : AUTO-MANUAL AND COMPACT GRAIN CRUSHING SYSTEM
(51) International classification :F16H
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)RAMADOSS SAMBATHKUMAR
Address of Applicant :19/10, HOSPITAL ROAD,
ARUMBAVUR(PO), VEPPANTHATTAI(TK),
PERAMBALUR(DT), TAMILNADU-621103 Tamil Nadu India
1)RAMADOSS SAMBATHKUMAR
2)DEEPIKA SAMBATHKUMAR
3)NALLAPAREDDIYAR RAMADOSS
(57) Abstract :
The present subject matter relates to the Auto-manual and compact grain crushing system to process the material right from cleaning,
soaking, crushing and cleaning the system with help of electronic control unit and user interface panel. The whole process can be
completed through auto mode and or manual mode upon users desire.

Publication After 18 Months:
The following Patent Applications have been published under Section 11A (3) of The Patents (Amendment) Act, 2005. Any
Person may file representation by way of opposition to the Controller of Patents at the appropriate office against the grant of
the patent in the prescribed manner under section 25(1) of the Patents (Amendment) Act, 2005 read with the rule 55 of The
Patents (Amendment) Rules, 2006:
(19) INDIA
(54) Title of the invention : COLD ROLLED STEEL SHEET AND METHOD FOR PRODUCING SAME
(51) International classification:C22C38/00,C21D9/46,C22C38/06
(31) Priority Document No :2011117432
(33) Name of priority country :Japan
No
Filing Date
:PCT/JP2012/063261
:24/05/2012
No
:WO 2012/161241
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)NIPPON STEEL & SUMITOMO METAL
CORPORATION
Address of Applicant :6 1 Marunouchi 2 chome Chiyoda ku
Tokyo 1008071 Japan
1)TODA Yuri
2)OKAMOTO Riki
3)FUJITA Nobuhiro
4)SANO Kohichi
5)YOSHIDA Hiroshi
6)OGAWA Toshio
7)HAYASHI Kunio
8)NAKANO Kazuaki
(57) Abstract :
The cold rolled steel sheet has a mean pole density of {100} <011> {223} <110> orientations that is between 1.0 and 5.0; a pole
density of {332} <113> crystal orientation that is between 1.0 and 4.0; an rC which is the Lankford coefficient perpendicular to the
rolling direction that is between 0.70 and 1.50; an r30 which is the Lankford coefficient at a 30º angle to the rolling direction that is
between 0.70 and 1.50; and a metal composition by vol% of 30 to 99% ferrite + bainite and 1 to 70% of martensite.

(19) INDIA
(54) Title of the invention : HOT ROLLED STEEL SHEET AND PROCESS FOR PRODUCING SAME
(51) International classification:C22C38/00,C21D9/46,C22C38/06
No
Filing Date
:PCT/JP2012/063273
:24/05/2012
No
:WO 2012/161248
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
CORPORATION
Tokyo 1008071 Japan
1)SANO Kohichi
2)HAYASHI Kunio
3)NAKANO Kazuaki
4)OKAMOTO Riki
5)FUJITA Nobuhiro
(57) Abstract :
This hot rolled steel sheet has an average pole density for {100}<011> to {223}<110> orientations of 1.0 5.0 has a pole density for the
crystal orientation {332}<113> of 1.0 4.0 and has a metallographic structure which comprises in terms of areal proportion 30 99%
ferrite and bainite and 1 70% martensite and which satisfies the following relationships (1) and (2) wherein fM is the areal proportion
of the martensite in % by area dia is the average size of the martensite in µm dis is the average distance between martensite grains in
µm and TS is the tensile strength of the steel sheet in MPa. dia=13 µm (relationship 1) TS/fM—dis/dia=500 (relationship 2)

(19) INDIA
(54) Title of the invention : COMPOSITIONS AND METHODS
(51) International classification :C07C43/00
Filing Date
:PCT/US2012/035434
:27/04/2012
(87) International Publication No :WO 2012/149302
(61) Patent of Addition to Application
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)NORTHSHORE UNIVERSITY HEALTHSYSTEM
Address of Applicant :1301 Central Street Evanston IL 60201
U.S.A.
1)ROY Hemant K.
2)WALI Ramesh K.
3)KUNTE Dhananjay
(57) Abstract :
Compositions comprising polyethylene glycol (PEG) are disclosed for the prophylaxis and/or treatment of head and neck squamous
cell carcinomas (HNSCC). Methods for the prophylaxis and/or treatment of HNSCC comprising administering an effective amount of
PEG are also disclosed. Also disclosed are methods and compositions for suppressing the surface expression of EGFR using PEG.

(19) INDIA
(54) Title of the invention : POLYMERIC NANOPARTICLES FOR DRUG DELIVERY
(51) International classification :A61K9/51
(31) Priority Document No :1107719.5
(33) Name of priority country :U.K.
Filing Date
:PCT/IB2012/052320
:09/05/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)INSTITUT QUIMIC DE SARRIA
Address of Applicant :Via Augusta 390 E 08017 Barcelona
Spain
1)GOMEZ Salvador Borros
2)DI MAURO Primiano Pio
(57) Abstract :
Disclosed are nanoparticles comprising a block copolymer and optionally one or more active agent(s) compositions comprising said
nanoparticles and methods of preparing said nanoparticles. The block copolymer comprises blocks (i) a first polymer that is a
polyester or polyamide and (ii) a second polymer comprising a hydrocarbon chain containing ester or ether bonds with hydroxyl
number = 10. The active agent(s) may be present within the nanoparticles or on the surfaces of the nanoparticles. The nanoparticles
may optionally be associated with a surface modifying moiety such that they are useful as drug delivery and molecular imaging
devices. The surface modifying moiety may target the nanoparticles to a desired target cell tissue or biomarker.

(19) INDIA
(54) Title of the invention : SOLAR THERMAL POWER PLANT
(51) International classification :F01K3/12,F03G6/06,F22B1/00
(33) Name of priority country :EPO
Filing Date
:PCT/EP2012/058970
:15/05/2012
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)ALSTOM TECHNOLOGY LTD
Address of Applicant :Brown Boveri Strasse 7 CH 5400
Baden Switzerland
1)AGA Vipluv
2)SIMIANO Marco
3)BOSCHEK Erik
(57) Abstract :
A solar thermal power plant 20 comprises a solar radiation receiver 28 mounted on a tower 22 surrounded by a heliostat field 24 to
receive solar radiation reflected by heliostats 26 forming the heliostat field 24. The power plant 20 comprises a power generation
circuit 30 including a steam turbine for driving an electrical generator to produce electrical power and water in the power generation
circuit 30 is capable of being heated directly by solar radiation reflected onto the solar radiation receiver 28 by the heliostat field 24 to
generate steam to drive the steam turbine. The power plant 20 also comprises an energy storage circuit 36 including a thermal energy
storage fluid such as molten salt which is capable of being heated directly by solar radiation reflected by the heliostat field 24. A heat
exchanger 44 is also provided for recovering thermal energy from the thermal energy storage fluid in the energy storage circuit 36; the
recovered thermal energy may then be used to generate steam to drive the steam turbine.

(19) INDIA
(54) Title of the invention : TRITYLATED ETHERS
(51) International
classification
:C10L1/185,C07C43/20,C10M129/16
(33) Name of priority
country
:U.S.A.
(86) International
Application No
Filing Date
:PCT/US2012/043718
:22/06/2012
(87) International
Publication No
:WO 2012/177987
Application Number
Filing Date
:NA
:NA
(62) Divisional to
Application Number
Filing Date
:NA
:NA
1)ANGUS CHEMICAL COMPANY
Address of Applicant :1500 East Lake Cook Road Buffalo
Grove IL 60089 U.S.A.
1)GREEN George D.
2)SWEDO Raymond
(57) Abstract :
A compound having formula (PhC)Ar(OR) wherein Ph represents a phenyl group Ar is an aromatic ring system having from six to
twenty carbon atoms R is C C alkyl or C C aralkyl m is one or two and n is an integer from one to four.

(19) INDIA
(54) Title of the invention : METHOD FOR CLEANING AND STRIPPING A TURBOSHAFT ENGINE BLADE USING A
PULSED LASER
(51) International classification :F01D5/00,F01D5/28,F01D25/00
(33) Name of priority country :France
No
Filing Date
:PCT/FR2012/050972
:02/05/2012
(87) International Publication No:WO 2012/150413
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)SNECMA
Address of Applicant :Socit Anonyme 2 Boulevard du Gnral
Martial Valin F 75015 Paris France
1)HUGOT Juliette
2)BOURDIN Franck
3)FEVRIER Thierry
4)GESTIN Jr´me
(57) Abstract :
A method for cleaning a turboshaft engine blade (1) comprising a superalloy body covered with a coating, in which the coating of the
blade (1) is at least partially machined using a pulsed laser (3), at least the feed rate of the pulsed laser (3) and the pulse frequency of
the pulsed laser (3) being parameterised such that the machined surface of the blade (1) has a 10 roughness of 4 pm to 10 pm.

(19) INDIA
(54) Title of the invention : CONTACT MATERIAL FOR VACUUMINTERRUPTER AND METHOD OF MAKING A CONTACT
MATERIAL
(51) International classification :H01H1/02,C22C1/04,C22C27/06
No
Filing Date
:PCT/EP2012/002250
:25/05/2012
No
:WO 2012/163509
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)ABB TECHNOLOGY AG
Address of Applicant :Affolternstrasse 44 CH 8050 Zurich
Switzerland
1)SIMON Reinhard
2)GENTSCH Dietmar
(57) Abstract :
Contact material for vacuum interrupter and method of making a contact material. In order to being enabled in a precise control of the
Si concentration of Cu/Cr contact materials contact material has a chromium content which is above 10 wt.% and that the material is
doped with silicon below 0 2 wt.% (2000 ppm Si) and the remainder is copper Cu.

(19) INDIA
(54) Title of the invention : INTERFERENCE MEASUREMENT IN WIRELESS NETWORKS
(51) International classification :H04W24/10
Filing Date
:PCT/US2012/050459
:10/08/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)INTERDIGITAL PATENT HOLDINGS INC.
Address of Applicant :200 Bellevue Parkway Suite 300
Wilmington DE 19809 U.S.A.
1)LEE Moon il
2)MARINIER Paul
3)NAYEB NAZAR Shahrokh
4)TSAI Allan Y.
5)ZHANG Guodong
6)TOOHER J. Patrick
(57) Abstract :
Embodiments contemplate methods systems and apparatuses for interference measurement in a wireless communication
network including wireless communication networks the employ MIMO in uplink and/or downlink communication. Embodiments
contemplate identifying one or more interference measurement resource elements that may be received from one or more transmission
points. Embodiments also contemplate performing interference measurement estimation based at least in part on the identified one or
more interference measurement resource elements. Channel state information (CSI) perhaps in the form of reports may be generated
based at least in part on the one or more interference measurement estimation. Embodiments also contemplate that the CSI report may
be transmitted to one or more nodes. In some embodiments the one or more interference measurement resource elements may be
received as part of a set of resource elements.

(19) INDIA
(54) Title of the invention : FURNACE WALL STRUCTURE OF MOLTEN METAL CONTAINER AND METHOD FOR
CONSTRUCTING FURNACE WALL OF MOLTEN METAL CONTAINER
(51) International classification :F27D1/00,C04B35/043
Filing Date
:PCT/JP2012/058136
:28/03/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
CORPORATION
Tokyo 1008071 Japan
1)UMEDA Shingo
2)KISHIGAMI Teruhisa
3)KONDO Masaaki
4)SATOYOSHI Yasunori
(57) Abstract :
In this furnace wall structure of a molten metal vessel, in a case that a thickness of a furnace wall except a shell when the furnace wall
is seen in a vertical cross-sectional view is set to be T (mm), a heat insulation material with a thermal conductivity of not less than
0.01 W/(mK) and not more than 0.15 W/(mK) in a range of 25°C to 300°C, with a mehing point of not less than 1000°C and not more
than I400°C, and with a thickness of not less than 2 mm and not more than 10 mm is arranged in a range in a thickness direction
between a position not less than 0.75xT (mm) and not more than 0.92xT from an interior surface of the magnesia carbon refractory
toward the shell.

(19) INDIA
(54) Title of the invention : OILY GEL COMPOSITION
(51) International classification :A61K8/55,A61K8/31,A61K8/37
No
Filing Date
:PCT/JP2012/062488
:16/05/2012
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)DAICEL CORPORATION
Address of Applicant :3 4 5 Umeda Kita ku Osaka shi Osaka
5300001 Japan
2)NIHON UNIVERSITY
1)SAKANISHI Yuichi
2)HASHIZAKI Kaname
3)SAITO Yoshihiro
4)TAGUCHI Hiroyuki
(57) Abstract :
Provided is a gel-forming agent that is easy to prepare and has all the properties including high safety for the living body and the
environment, satisfactory gel-forming capability, comfortable feeling upon use, and good handleability. The gel-forming agent
includes a lecithin, and a polyglycerol fatty acid ester in an amount of from 30 to 150 parts by weight per 100 parts by weight of the
lecithin. The polyglycerol fatty acid ester has a fatty acid residue having 14 or less carbon atoms, has an HLB of 15 or more as
determined based on an organic conceptual diagram, and has a degree of glycerol polymerization of from 8 to 40.

(19) INDIA
(54) Title of the invention : INLET VALVE FOR A FLUID PUMP AND ASSEMBLY METHOD FOR AN INLET VALVE FOR A
FLUID PUMP
(51) International
classification
:F04B7/00,F04B7/0056,F04B53/10
(31) Priority Document No :10 2011 076 784.3
(33) Name of priority country :Germany
No
Filing Date
:PCT/EP2012/059990
:29/05/2012
No
:WO 2012/163892
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)CONTINENTAL AUTOMOTIVE GMBH
Address of Applicant :Vahrenwalder Strae 9 30165 Hannover
Germany
1)VAN HIMME Luc
2)VERMOLEN Koen
3)MEEKERS Rudi
(57) Abstract :
The invention relates to an inlet valve (101) for a fluid pump comprising a movably supported tappet (103) for closing a fluid inlet
opening and an actuator (105) for moving the tappet (103) wherein the actuator (105) and the tappet (103) are formed separately from
each other and can be coupled to one another by means of a coupling element (107) for transmitting an actuator driving force to the
tappet (103). The invention further relates to an assembly method for an inlet valve (101).

(19) INDIA
(54) Title of the invention : PIGMENT FOR PAPER AND PAPER LAMINATE
(51) International classification :D21H19/38,C09C1/00
Filing Date
:PCT/US2012/050069
:09/08/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)CRISTAL USA INC.
Address of Applicant :20 Wight Avenue Suite 100 Hunt
Valley MD 21030 U.S.A.
1)BURNISTON Neil
2)BURNISTON Robert
(57) Abstract :
A pigment mixture comprising (a) pigment particles (b) colloidal spacer particles dispersed on surfaces of the pigment particles and
(c) carrier particles wherein the pigment particles with colloidal spacer particles are dispersed on surfaces of the carrier particles. A
pigment mixture of titanium dioxide pigment particles having colloidal silica spacer particles on surfaces of the titanium dioxide the
titanium dioxide and colloidal silica attached to surfaces of diatomaceous earth carrier particles provides improved optical efficiency
of the pigment and improved retention in a paper fiber matrix.

(19) INDIA
(54) Title of the invention : RELEASABLE CONNECTION BETWEEN A HANDLE AND A PAN AND A PAN WITH SAID
CONNECTION
(51) International classification :A47J45/07
(31) Priority Document No :MI2011A000841
(33) Name of priority country :Italy
Filing Date
:PCT/IB2011/053690
:23/08/2011
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)GBB SRL
Address of Applicant :Via San Lorenzo 141 I 20824 Lazzate
(MB) Italy
1)BOGANI Giuseppe
(57) Abstract :
A releasable connection between a pan and a handle comprises a bracket which is provided with a hole (16) and intended to project
laterally from the body of the pan and an engaging mechanism which is intended to be arranged on the handle and which comprises an
engaging tooth (17) which is inserted into said hole (16) and a cam element (19) which is rotatable into a locked position for pushing
with a first cam surface (23) against a corresponding edge (15) of the said hole (16) so as to clamp a part (21) of the bracket (11)
between the first said cam surface (23) and a facing projecting part (20) of the engaging mechanism. A strip (23) allowing sliding of
the cam and pressing against the edge of the hole is arranged between the said first cam surface (23) and the corresponding edge (15)
of the hole. Advantageously the bracket may be made as one piece with an aluminium pan.

(19) INDIA
(54) Title of the invention : AIR CONDITIONING SYSTEM FOR AN AIRCRAFT PASSENGER COMPARTMENT
(51) International classification :B64D13/08,B64D13/06
(33) Name of priority country :France
Filing Date
:PCT/FR2012/051196
:29/05/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)TURBOMECA
Address of Applicant :F 64511 Bordes France
1)HOUSSAYE Laurent
2)MINEL Laurent
(57) Abstract :
An air conditioning system for an aircraft passenger compartment (1), the system including an air supply circuit connecting at least
one external air inlet (E) to at least one air distribution outlet (S) which opens into the compartment (1), an auxiliary power unit (4)
mounted in said supply circuit and arranged so as to compress an air stream in the supply circuit, the supply circuit including a heating
first branch (B1) which connects the auxiliary power unit (4) to the air distribution outlet (S), and in which heating means (6) are
mounted, a cooling second branch (B2) which connects the auxiliary power unit (4) to the air distribution outlet (S), and switching
means (83-86) which are adapted so as to distribute the air stream between the heating first branch (B1) and the cooling second branch
(82).

(19) INDIA
(54) Title of the invention : COMMUNICATION DEVICE COMMUNICATION SYSTEM AND COMMUNICATION METHOD
(51) International
classification
:H04W88/06,H03J9/02,H04M11/00
No
Filing Date
:PCT/JP2012/067331
:06/07/2012
No
:WO 2013/005832
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)Yokogawa Electric Corporation
Address of Applicant :9 32 Naka cho 2 chome Musashino shi
Tokyo 1808750 Japan
1)CHEN Hua Jun
(57) Abstract :
A communication device, in which the OSI reference model physical layer and data-link layer perform wireless communication via at
least one of a first wireless 5 network conforming to a first wireless communication standard and a second wireless network
conforming to a second wireless communication standard, may include an identification control unit, provided in the data-link layer,
that identifies that data, which is received in the physical layer, based on the identification information included in the data, is to be
transmitted via either the first wireless network or the second wireless 10 network, the identification control unit controlling so as to
transmit, based on the identification result, the data via the first wireless network or the second wireless network.

(19) INDIA
(54) Title of the invention : MICROWAVEABLE PACKAGES HAVING A COMPOSITE SUSCEPTOR
(31) Priority Document No :PCT/US2011/038583
Filing Date
:PCT/EP2012/059586
:23/05/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)NESTEC S.A.
Address of Applicant :Av. Nestl 55 CH 1800 Vevey
Switzerland
1)ERLE Ulrich Johannes
(57) Abstract :
Microwaveable packages having composite susceptors and methods for using same are provided. In a general embodiment composite
susceptors for cooking microwaveable foods (12 14) in a microwave oven are provided. The composite susceptors may include for
example a first layer that is a standard microwave susceptor (30) and a second layer (32) comprising mobile charges wherein the
second layer is at least substantially metal free. The second layer comprising mobile charges can both shield the standard susceptor
from microwaves and act as a conductor to increase the conductivity of the standard susceptor. The composite susceptors of the
present disclosure provide improved surface heating patterns that are similar to surface heating patterns of conventional ovens while
also providing the benefits of microwave cooking.

(19) INDIA
(54) Title of the invention : HYBRID MICROFLUIDIC ASSEMBLIES
(51) International classification :G01N21/00
Filing Date
:PCT/US2012/041978
:12/06/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)CORNING INCORPORATED
Address of Applicant :1 Riverfront Plaza Corning New York
14831 U.S.A.
1)GUIDAT Roland
2)LOBET Olivier
3)MARQUES Paulo Gaspar Jorge
4)WOEHL Pierre
(57) Abstract :
Embodiments of hybrid microfluidic assemblies comprise at least one microstructure that is formed of transparent material and is
substantially free of non transparent material and further comprise at least one microstructure that is formed of non transparent
material and is substantially free of transparent material.

(19) INDIA
(54) Title of the invention : KEY PULLEY SEGMENT FEATURES SEGMENT STACK CONFIGURATION AND CAM AND
ROLLER DESIGN AND ACTUATION IN A SYNCHRONIZED SEGMENTALLY INTERCHANGING PULLEY
TRANSMISSION SYSTEM
(51) International classification :F16H55/56,F16H7/22,F16H9/06
No
Filing Date
:PCT/CA2012/000381
:26/04/2012
Application Number
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
1)1783590 ONTARIO LTD. D/B/A INMOTIVE
Address of Applicant :101 College St. Suite 215 The MaRS
Centre Toronto Ontario M5G 1L7 Canada
1)WONG Anthony
2)BOTTERO Paul
3)DOYLE Michael
(57) Abstract :
A key pulley segment in a synchronized segmentally interchanging pulley transmission system is either first or last in a pulley
segment set to engage an endless member. The first or last key segment teeth to engage or disengage respectively are shortened or
completely trimmed and the adjacent pulley segment to the key segment is elongated such that the inward portion of the tooth profile
extends toward the key segment. Shortened tooth or teeth and an elongated adjacent segment together allow for many pulley segments
to be designed as key segments. Completely trimmed teeth may be engineered to create a supporting surface for the endless member
on the key segment. The elongated adjacent segment may have an extending portion which slidably mates with the supporting surface
of the key segment thereby receiving radial support therefrom. Multiple pulley segments from different pulley segment sets may be
connected or constructed to move together in a unified stack and may be staggered such that any one segment may be in an engaging
position with the endless member when the unified stack is moved along the axis of rotation. Unified stacks may have guiding rails on
both inner and outer radial surfaces and the pulley assembly may have mating features that receive such guiding rails. Any number of
the pulley segments in a unified stack may be key pulley segments. Pulley segments of a stack may be vertically separated into one or
more unified stacks. Unified stacks may be moved by way of a cam or roller cam system where each unified stack has a slidably or
ratably attached roller and roller arm. Chassis mounted cams engage the rollers outside of the contact zone rollers and roller arms are
moved into and out of engagement with the cams and individual segments of a unified stack are moved into or out of engagement.
Rollers may be actuated into and out of engagement by electromagnets fixably mounted in an array. Rollers may discretely engage
with multiple cams by way of several electromagnet arrays and thereby complete several stack axial motions. Electromagnets in an
array may be selectively energized to move selected rollers to an active position in order to effect key pulley segment
engagement stack axial movement and transition.

(19) INDIA
(54) Title of the invention : APPARATUS AND METHOD FOR CONNECTING MULTIPLE VOLTAGE ONBOARD POWER
SUPPLY SYSTEMS
(51) International classification :H02J1/00
Filing Date
:PCT/EP2012/059583
:23/05/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ROBERT BOSCH GMBH
Address of Applicant :Postfach 30 02 20 70442 Stuttgart
Germany
1)WALENTA Sebastian
2)PISCHKE Ulf
3)DRAESE Nils
(57) Abstract :
An apparatus and a method are proposed for connecting multiple-voltage onboard power supply systems, wherein the apparatus
comprises at least one DC/DC voltage converter (10) which can couple a first onboard power supply system (12) having a first
onboard power supply system voltage (Ul) to a second onboard power supply system (14) having a second onboard power supply
system voltage (U2), wherein besides the DC/DC voltage converter (10) at least one charging means (18) is provided for increasing
the second onboard power supply system voltage (U2).

(19) INDIA
(54) Title of the invention : METHOD FOR GENERATING AT LEAST ONE THROUGH HOLE AND DEVICE FOR CARRYING
OUT SUCH A METHOD
(51) International
classification
:B23K26/38,B23K26/18,F02M61/16
country
:Germany
(86) International
Application No
Filing Date
:PCT/EP2012/061588
:18/06/2012
No
:WO 2013/004475
Application Number
Filing Date
:NA
:NA
(62) Divisional to
Application Number
Filing Date
:NA
:NA
1)ROBERT BOSCH GMBH
Germany
1)BAUER Thorsten
2)KOENIG Jens
(57) Abstract :
The invention relates to a method for generating at least one through-hole (3, 4) in a wall of a workpiece (2) bounding a hollow space
(12) of the workpiece (2), said method using a laser beam (7) directed onto the wall (9) from the exterior. A paste-like protective agent
(13) is thereby introduced into the hollow space of the workpiece (2). The paste-like protective agent (13) is applied in an extension
(10) of the laser beam (7) guided through the throughhole (3) in front of a rear wall bounding the hollow space (12). Reliable
protection of the rear wall (11) during laser drilling of the through-hole (3) is thereby ensured.

(19) INDIA
(54) Title of the invention : INJECTION DEVICE
(51) International classification :F01N3/20
Filing Date
:PCT/EP2012/059722
:24/05/2012
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ROBERT BOSCH GMBH
Germany
1)GOTTWALD Frank
(57) Abstract :
The invention relates to a device for injecting a fluid (2), in particular into the exhaustgas section of an internal combustion engine,
having a reservoir (4) for storing the fluid (2) to be injected; an injection and metering module (10); a pump (8) which is configured
for conveying fluid (2) during operation out of the reservoir (4) to the injection and metering module (10); and a return line (16) which
makes an outflow of fluid (2) out of the injection and metering module (10) possible, wherein a switchable throttling valve (14) which
is suitable for pumping fluid out of the injection and metering module (10) is arranged in the return line (16).

(19) INDIA
(54) Title of the invention : DEVICE AND METHOD FOR MEASURING THE PARTICLE CONCENTRATION IN AN AEROSOL
(51) International
classification
:G01N21/15,G01N21/53,G01N15/06
country
:Germany
(86) International
Application No
Filing Date
:PCT/EP2012/061323
:14/06/2012
(87) International
Publication No
:WO 2013/013882
Application Number
Filing Date
:NA
:NA
(62) Divisional to
Application Number
Filing Date
:NA
:NA
1)ROBERT BOSCH GMBH
Germany
1)STENGEL Karl
2)MATTEUCCI Andrea
3)HAAGA Gerhard
4)NEUENDORF Michael
5)STAIB Joerg
(57) Abstract :
A device (10) for measuring the particle concentration in an aerosol (22), with a flow tube (4) and a measurement chamber (12c), has
a cavity (12) branching off from the flow tube (4) and a sleeve (14) arranged in said cavity (12), the sleeve comprising, at an end
facing away from the flow tube (4), a collar (15) extending around the periphery of the sleeve (14) and fixed to the periphery of the
cavity (12). At least one inflow opening (16) is formed in the collar, and an end of the sleeve (14) facing the flow tube (4) extends into
the flow tube (4). At least one outflow opening (18) is formed at the end of the sleeve (14) facing the flow tube (4), and the
measurement chamber (12c) is formed in the cavity (12) on the side of the sleeve (14) facing away from the flow tube (4).

Published patent and design registration information january 30th, 2015

Published patent and design registration information january 30th, 2015

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Published patent and design registration information january 30th, 2015

Similar to Published patent and design registration information january 30th, 2015 (19)

More from InvnTree IP Services Pvt. Ltd.

More from InvnTree IP Services Pvt. Ltd. (20)

Recently uploaded

Recently uploaded (20)

Published patent and design registration information january 30th, 2015