NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual

PROVEN PERFORMANCE
MHCity
MHPlus
MH5.6
MHCity
MHPlus
MH5.6
Print No. 87677413A
English
Repair Manual
*Tier III*
Repair
Manual
*Tier III*

TO PREVENT ACCIDENTS
The majority of accidents and injuries which occur in industry, at home or on the road, are caused by the failure
of some individual to follow simple and fundamental safety rules or precautions. For this reason MOST ACCI-
DENTS CAN BE PREVENTED by recognizing the real cause and taking the necessary precautions, before the
accident occurs.
Regardless of the care used in design and construction of any type of equipment, there may be conditions that
cannot be completely safeguarded against, without interfering with reasonable accessibility and efficient oper-
ation.
A careful operator and / or technician is the best insurance against accidents. The complete observance of one
simple rule would prevent many thousands of serious injuries each year.
This rule is: never attempt to clean, lubricate or adjust a machine while it is in motion.
SWARNING
Before carrying out any maintenance operation, adjustment and or repair on machines equipped with
attachments, controlled hydraulically or mechanically, make sure that the attachment is lowered and safely set
on the ground. If it is necessary to have the equipment partially or fully raised to gain access to certain items,
be sure the equipment is suitably supported by means other than the hydraulic lift cylinders, cable and /or

SAFETY INSTRUCTION
This warning symbol points out important
messages involving your safety.
Carefully read the safety rules contained herein and
follow advised precautions to avoid potential
hazards and to safeguard your safety and personal
integrity.
In this manual you will find this symbol together with
the following key-words:
SWARNING
This symbol warns about the possibility of potential
damages to the machine that can involve the
operator’s safety.
SDANGER
With specific warnings about potential dangers for
the operator’s or other persons integrity directly or
indirectly involved.
The non compliance with the warning preceded by
the above mentioned key-words (WARNING and
DANGER) can cause serious accidents or even the
death of the persons involved.
Moreover in the present Manual have been given
some instructions with texts in italics, preceded by
the words NOTE and CAUTION:
NOTE: it emphasizes and underlines to the operator
the correct technique or correct procedure to follow.
SCAUTION
It warns the operator of a possible hazard of
machine damage in case he does not follow a
determined procedure.
S

INDEX
SECTION 01 - SAFETY PRECAUTIONS
1. GENERAL SAFETY INSTRUCTIONS........................................................................................................ 2
2. USE INSTRUCTION................................................................................................................................. 11
SECTION 02 - CONTROLS AND INSTRUMENTS
1. SWITCHES AND PUSH-BUTTONS........................................................................................................... 1
2. CONTROLS AND PEDALS ........................................................................................................................ 6
3. MULTI-FUNCTION DISPLAY ................................................................................................................... 10
SECTION 03 - TECHNICAL SPECIFICATIONS
1. MAIN COMPONENTS ................................................................................................................................ 1
2. DIMENSIONS - OPERATING WEIGHTS................................................................................................... 3
3. DIGGING PERFORMANCE ..................................................................................................................... 19
4. LIFTING CAPACITIES.............................................................................................................................. 33
5. HYDRAULIC SYSTEM ............................................................................................................................. 39
6. ROTATION ............................................................................................................................................... 40
7. TRAVEL.................................................................................................................................................... 41
8. TYRES...................................................................................................................................................... 42
9. BRAKES ................................................................................................................................................... 42
10. STEERING ............................................................................................................................................... 42
11. ELECTRICAL SYSTEM............................................................................................................................ 42
12. BUCKETS................................................................................................................................................. 43
13. TIGHTENING TORQUES......................................................................................................................... 44
14. CENTRALIZED LUBRICATION PUMP (OPTIONAL)............................................................................... 44
15. FUEL SYSTEM......................................................................................................................................... 44
16. ENGINE .................................................................................................................................................... 45
17. SUPPLY SUMMARIZING CHART............................................................................................................ 46
SECTION 04 - UPPER STRUCTURE
1. MAIN COMPONENTS ................................................................................................................................ 1
2. SLEWING BEARING .................................................................................................................................. 2
3. ROTATION GEARMOTOR......................................................................................................................... 7
3.1 DISASSEMBLY AND ASSEMBLY ................................................................................................... 12
3.2 SPECIAL TOOLS ............................................................................................................................. 34
4. MULTI-COOLER....................................................................................................................................... 35
4.1 TECHNICAL SPECIFICATIONS ...................................................................................................... 36
5. HYDRAULIC PUMPS ............................................................................................................................... 39
6. MUFFLER................................................................................................................................................. 40
7. HYDRAULIC OIL TANK............................................................................................................................ 41
8. AIR FILTER .............................................................................................................................................. 47
9. COUNTERWEIGHT.................................................................................................................................. 47
10. FUEL SYSTEM......................................................................................................................................... 48

11. CAB AND OPERATOR’S SEAT ............................................................................................................... 55
12. CENTRALIZED LUBRICATION PUMP..................................................................................................... 66
SECTION 05 - UNDERCARRIAGE
1. UNDERCARRIAGE COMPONENTS.......................................................................................................... 1
2. REAR RIGID AXLE..................................................................................................................................... 2
2.1 TECHNICAL SPECIFICATIONS......................................................................................................... 3
2.2 DISASSEMBLY AND ASSEMBLY...................................................................................................... 6
2.3 DISASSEMBLY AND ASSEMBLY...................................................................................................... 8
2.4 TROUBLESHOOTING...................................................................................................................... 87
2.5 SPECIAL TOOLS.............................................................................................................................. 89
3. TRAVEL MOTOR...................................................................................................................................... 90
3.1 TECHNICAL SPECIFICATIONS....................................................................................................... 90
3.2 DISASSEMBLY AND ASSEMBLY.................................................................................................... 91
3.3 DISASSEMBLY AND ASSEMBLY.................................................................................................... 92
4. CARDAN SHAFT .................................................................................................................................... 103
4.1 DISASSEMBLY AND ASSEMBLY.................................................................................................. 104
5. FRONT STEERING AXLE ...................................................................................................................... 106
5.1 TECHNICAL SPECIFICATIONS..................................................................................................... 107
5.4 TROUBLESHOOTING.................................................................................................................... 185
5.5 SPECIAL TOOLS............................................................................................................................ 187
6. WHEELS AND TYRES ........................................................................................................................... 188
7. BLADE .................................................................................................................................................... 192
7.1 BLADE CYLINDER......................................................................................................................... 194
8. AXLE FLOATING LOCKING CYLINDERS ............................................................................................. 202
8.3 AIR BLEEDING............................................................................................................................... 205
9. STABILIZERS ......................................................................................................................................... 209
9.1 STABILIZER CYLINDERS.............................................................................................................. 212
10. LEFT LADDER........................................................................................................................................ 223
11. RIGHT LADDER AND TOOL STORAGE BOX....................................................................................... 224
12. ROTARY CONTROL VALVE AND ELECTRIC ROTOR......................................................................... 225
12.4 ELECTRIC ROTOR ........................................................................................................................ 229
SECTION 06 - FRONT ATTACHMENT
1. TYPES OF FRONT ATTACHMENT ........................................................................................................... 2
2. HYDRAULIC CYLINDERS.......................................................................................................................... 4
2.1 BOOM CYLINDER.............................................................................................................................. 5
2.2 SPECIAL TOOLS.............................................................................................................................. 50

3. BUCKETS................................................................................................................................................. 51
4. QUICK COUPLER .................................................................................................................................... 55
5. CLAMSHELL BUCKET............................................................................................................................. 59
SECTION 07 - STEERING SYSTEM
1. OPERATION............................................................................................................................................... 1
2. POWER STEERING................................................................................................................................... 3
2.1 DISASSEMBLY AND ASSEMBLY ..................................................................................................... 5
3. PRIORITY VALVE .................................................................................................................................... 23
4. TROUBLESHOOTING.............................................................................................................................. 24
SECTION 08 - BRAKE SYSTEM
1. OPERATION............................................................................................................................................... 1
2. SERVICE BRAKE....................................................................................................................................... 4
3. PARKING BRAKE ...................................................................................................................................... 7
4. PEDAL BRAKE VALVE .............................................................................................................................. 8
5. ACCUMULATORS...................................................................................................................................... 9
SECTION 09 - HYDRAULIC SYSTEM
1. HYDRAULIC SYSTEM ............................................................................................................................... 1
2. HYDRAULIC SYSTEM DIAGRAMS ........................................................................................................... 5
2.1 HYDRAULIC SYSTEM DIAGRAMS - UPPER STRUCTURE ............................................................ 5
2.2 HYDRAULIC SYSTEM DIAGRAMS - UNDERCARRIAGE .............................................................. 23
2.3 HYDRAULIC SYSTEM DIAGRAMS BLADE AND/OR STABILIZERS ............................................. 27
3. HYDRAULIC PUMPS ............................................................................................................................... 31
4. UPPER STRUCTURE CONTROL VALVE ............................................................................................... 48
5. UNDERCARRIAGE CONTROL VALVE ................................................................................................... 58
6. PILOT CONTROL ASSY .......................................................................................................................... 60
7. ROTATION SYSTEM ............................................................................................................................... 69
8. TRAVEL.................................................................................................................................................... 73
9. STABILIZATION HYDRAULIC SYSTEM.................................................................................................. 84
10. BOOM HYDRAULIC SYSTEM ................................................................................................................. 90
11. HYDRAULIC SYSTEM ............................................................................................................................. 97
12. HYDRAULIC SYSTEM OF DIPPER....................................................................................................... 103
13. HYDRAULIC SYSTEM OF PLACING BOOM......................................................................................... 107
14. HYDRAULIC SYSTEM WITH COMBINATION OF DIFFERENT FUNCTIONS
(BOOM, PLACING BOOM, DIPPER AND BUCKET)114
15. HYDRAULIC SYSTEM OF HAMMER (WITH PLACING BOOM)........................................................... 116
16. HYDRAULIC SYSTEM OF HAMMER AND SHEARS (WITH PLACING BOOM)................................... 119
17. HYDRAULIC SYSTEM OF SHEARS (WITH PLACING BOOM) ............................................................ 124
18. HYDRAULIC SYSTEM OF HAMMER (WITH MONOBOOM)................................................................. 127
19. HYDRAULIC SYSTEM OF HAMMER AND SHEARS (WITH MONOBOOM) ........................................ 130
20. HYDRAULIC SYSTEM OF SHEARS (WITH MONOBOOM).................................................................. 135
21. TROUBLESHOOTING............................................................................................................................ 138

SECTION 10 - ELECTRICAL SYSTEM
1. ELECTRICAL DIAGRAMS.......................................................................................................................... 1
2. FUSES ...................................................................................................................................................... 41
3. BATTERIES .............................................................................................................................................. 44
4. BULBS ...................................................................................................................................................... 48
SECTION 11 - ELECTRONICS
1. MAIN COMPONENTS ................................................................................................................................ 1
1.1 ELECTRICAL POWER SUPPLY DIAGRAM ...................................................................................... 3
2. COMPONENTS OF LINE 1 ........................................................................................................................ 5
3. COMPONENTS OF LINE 2 ........................................................................................................................ 9
3.1 TRAVEL PEDAL ............................................................................................................................... 15
3.2 ATTACHMENT PEDAL (PLACING BOOM AND HAMMER)............................................................ 16
3.3 ELECTRO-HYDRAULIC SYSTEM ................................................................................................... 17
3.4 POWER CONTROL SYSTEM.......................................................................................................... 18
4. ENGINE SPEED ACTUATOR .................................................................................................................. 25
5. COOLANT TEMPERATURE DETECTION............................................................................................... 26
6. CHARGE AIR TEMPERATURE DETECTION.......................................................................................... 27
7. HYDRAULIC OIL TEMPERATURE DETECTION..................................................................................... 28
8. PROPORTIONAL VALVE - FAN MOTOR ................................................................................................ 29
9. PROPORTIONAL VALVES - CONTROL BLOCK..................................................................................... 30
SECTION 12 - CALIBRATION
1. NECESSARY OPERATIONS BEFORE CALIBRATION............................................................................. 1
2. DISPLAY: CALIBRATION MENU ............................................................................................................... 3
3. CALIBRATIONS WITH THE ENGINE RUNNING....................................................................................... 4
3.1 VDO CALIBRATION ........................................................................................................................... 6
3.2 POWER CALIBRATION ..................................................................................................................... 8
3.3 MAIN VALVE CALIBRATION (CONTROL VALVE).......................................................................... 10
3.4 TRAVEL CALIBRATION................................................................................................................... 13
3.5 PUMP DELIVERY CALIBRATION.................................................................................................... 15
3.6 ROTATION PUMP CALIBRATION................................................................................................... 18
3.7 AUXILIARY PRESSURE CALIBRATION ......................................................................................... 20
4. CALIBRATIONS WITH THE ENGINE STOPPED .................................................................................... 22
4.1 CALIBRATIONS, ALL SOLENOID VALVES, MAIN PUMP, ROTATION PUMP,
AUXILIARY PRESSURE24
4.2 MAIN VALVE CALIBRATION (CONTROL VALVE).......................................................................... 26
5. DISTRIBUTORE ....................................................................................................................................... 26
6. VALVOLA SOSTENIMENTO DEL CARICO............................................................................................. 29
7. DIAGNOSI INCONVENIENTI ................................................................................................................... 30

1. GENERAL SAFETY INSTRUCTIONS.......................................................................................................... 2
2. USE INSTRUCTION ................................................................................................................................... 11
SECTION 01 - SAFETY PRECAUTIONS

SECTION 01 - SAFETY PRECAUTIONS 1
Carefully read the safety rules contained herein and
follow advised precautions to avoid potential haz-
ards and to safeguard your safety and personal in-
tegrity.
In this manual you will find the following indications:
S WARNING
This symbol warns about the possibility of potential
damages to the machine that can involve the
operator’s safety.
S DANGER
With specific warnings about potential dangers for
the operator’s or other persons integrity directly or
indirectly involved.
The non compliance with the warning preceded by
the above mentioned key-words (WARNING and
DANGER) can cause serious accidents or even the
death of the persons involved.
Moreover in the present Manual have been given
some instructions with texts in italics, preceded by
the words NOTE and CAUTION, with following
meanings for machine protection:
NOTE: it emphasizes and underlines to the operator
the correct technique or correct procedure to follow.
S WARNING
It warns the operator of a possible hazard of machine
damage in case he does not follow a determined
procedure.
Your safety and that of people around you depends
on you. It is essential that you understand this man-
ual for the correct operation, inspection, lubrication
and maintenance of this machine.

2 SECTION 01 - SAFETY PRECAUTIONS
1. GENERAL SAFETY INSTRUCTIONS
Carefully read this Manual before proceeding with
maintenance, repairs, refuelling or other machine
operations.
Repairs have to be carried out only by authorized
and instructed staff; specific precautions have to be
taken when grinding, welding or when using mallets
or heavy hammers.
Not authorized persons are not allowed to repair or
carry out maintenance on this machine. Do not carry
out any work on the equipment without prior authori-
zation.
Ask your employer about the safety instructions in
force and safety equipment.
Nobody is allowed to seat on the operator’s place
during machine maintenance unless he is a qualified
operator helping with the maintenance work.
If it is necessary to move the equipment to carry out
repairs or maintenance, do not lift or lower the equip-
ment from any other position than the operator’s
seat.
Never carry out any operation on the machine when
the engine is running, except when specifically indi-
cated.
Stop the engine and ensure that all pressure is re-
lieved from hydraulic circuits before removing caps,
covers, valves, etc.
All repair and maintenance operations should be
carried out with the greatest care and attention.
Service stairs and platforms used in a workshop or
in the field should be built in compliance with the
safety rules in force.
Any functional disorders, especially those affecting
the safety of the machine, should therefore be recti-
fied immediately.

1.1 EMERGENCY
Be prepared for emergencies. Always keep at dis-
posal on the machine a first aid kit and a fire extin-
guisher. Make sure that the fire extinguisher is
serviced in accordance with the manufacturer’s in-
structions.
1.2 EQUIPMENT
Wear close fitting clothing and safety equipment ap-
propriate for the job:
Z safety helmet;
Z safety shoes;
Z heavy gloves;
Z reflective clothing;
Z wet weather clothing.
If environment condition require it following personal
safety equipment should be at hand:
Z respirators (or dustproof masks);
Z ear plugs or acoustic ears protections;
Z goggles with lateral shield or masks for eyes pro-
tection.
Do not wear rings, wristwatches, jewels, unbuttoned
or flapping clothing such as ties, torn clothes,
scarves, open jackets or shirts with open zips which
could get caught into moving parts.

1.3 ENGINE - RADIATOR
Never leave the engine run in closed spaces without
ventilation and not able to evacuate toxic exhaust
gases. Keep the exhaust manifold and tube free
from combustion materials.
Do not refuel with the engine running, especially if
hot, as this increases fire hazard in case of fuel spill-
age.
Never attempt to check or adjust the fan belts when
the engine is running.
Never lubricate the machine with the engine run-
ning.
Pay attention to rotary pieces and do not allow to an-
yone to approach to avoid becoming entangled.
If hands, clothes or tools get caught in the fan blades
or in the transmission belt, this can cause amputa-
tions, violent tears and generate condition of serious
danger; for this reason avoid touching or to come
close to all rotary or moving parts.
A violent jet of the coolant from the radiator can
cause damages and scalds.
If you are to check the coolant level, you have to shut
off the engine previously and to let cool down the ra-
diator and its pipes. Slowly unscrew the cap to re-
lease the inside pressure.
If necessary, remove the cap with hot engine, wear
safety clothes and equipment, then loosen the cap
slowly to relieve the pressure gradually.
When checking the fuel, oil and coolant levels, use
exclusively explosion proof classified lamps. If this
kind of lamps are not used fires or explosions may
occur.

1.4 HYDRAULIC SYSTEMS
Splashes of fluids under pressure can penetrate the
skin causing serious injuries.
Avoid this hazard by relieving pressure before dis-
connecting hydraulic or other lines.
Relieve the residual pressure by moving the hydrau-
lic control levers several times.
Tighten all connections before applying pressure.
To protect the eyes wear a facial shield or safety
goggles.
Protect your hands and body from possible splashes
of fluids under pressure.
Swallowing hydraulic oil is a severe health hazard.
When hydraulic oil has been swallowed, avoid vom-
iting, but consult a doctor or go to a hospital.
If an accident occurs, see a doctor familiar with this
type of injury immediately.
Any fluid penetrating the skin must be removed with-
in few hours to avoid serious infections.
Flammable splashes may originate because of the
heat near pipes with fluids under pressure, with the
result of serious scalds for the persons hit. Do not
weld or use torches near pipes containing fluids or
other flammable materials.
Pipes under pressure can accidentally be pierced
when the heat expands beyond the area immediate-
ly heated.
Arrange for fire resistant temporary shields to pro-
tect hoses or other components during welding.
Have any visible leakage repaired immediately.
Escaping oil pollutes the environment. Soak up any
oil that has escaped with a proper binding agent.
Sweep up binding agent and dispose of it separately
from other waste.
Never search for leakages with the fingers, but use a
piece of cardboard and always wear goggles.
Never repair damaged piping; always replace it. Re-
place hydraulic hoses immediately on detecting any
damage or moist areas.
Always store hydraulic oil in the original containers.

HOSES AND TUBES
Always replace hoses and tubes if the cone end or
the end connections on the hose are damaged.
When installing a new hose, loosely connect each
end and make sure the hose takes up the correct po-
sition before tightening the connections. Clamps
should be tightened sufficiently to hold the hose with-
out crushing and to prevent chafing.
After hose replacement to a moving component,
check that the hose does not foul by moving the
component through the complete range of travel.
Be sure any hose which has been installed is not
kinked or twisted.
Hose connections which are damaged, dented,
crushed or leaking, restrict oil flow and the productiv-
ity of the components being served. Connectors
which show signs of movement from the original po-
sition have failed and will ultimately separate com-
pletely.
A hose with a frayed outer sheath will allow the water
penetration. Concealed corrosion of the wire rein-
forcement will subsequently occur along the hose
length with resultant hose failure.
Ballooning of the hose indicates an internal leakage
due to structural failure. This condition rapidly deteri-
orates and total hose failure soon occurs.
Kinked, crushed, stretched or deformed hoses gen-
erally suffer internal structural damage which can re-
sult in oil restriction, a reduction in the speed of
operation and ultimate hose failure.
Free-moving, unsupported hoses must never be al-
lowed to touch each other or related working surfac-
es. This causes chafing which reduces hose life.
O-RINGS
Replace O-rings, seal rings and gaskets whenever
they are disassembled.
Never mix new and old seals or O-rings, regardless
of condition. Always lubricate new seal rings and O-
rings with hydraulic oil before installation to relevant
seats.
This will prevent the O-rings from rolling over and
twisting during mounting which will jeopardize seal-
ing.

1.5 BATTERY
Batteries give off explosive gases.
Never handle naked flames and unshielded light
sources near batteries, never smoke.
To prevent any risk of explosion, observe the follow-
ing instructions:
Z when disconnecting the battery cables, always dis-
connect the negative (-) cable first;
Z to reconnect the battery cables, always connect the
negative (-) cable last;
Z never short-circuit the battery terminals with metal
objects;
Z do not weld, grind or smoke near a battery.
Battery electrolyte causes severe burns. The bat-
tery contains sulphuric acid. Avoid any contact with
the skin, eyes or clothing.
Antidote:
Z EXTERNAL: rinse well with water, removing any
soiled clothing.
Z INTERNAL: avoid vomiting. Drink water to rinse
your mouth. Consult a doctor.
Z EYES: rinse abundantly with water for 15 minutes
and consult a doctor.
Z When the electrolyte of a battery is frozen, it can
explode if you attempt to charge the battery or if
you try to start the engine using a booster battery.
Always keep the battery charged to prevent the
electrolyte freezing.
Provide good ventilation when changing a battery or
using a battery in an enclosed space. Always protect
your eyes when working near a battery.
Never set tools down on the battery. They may in-
duce a short circuit, causing irreparable damage to
the battery and injuring persons.
Never wear metal necklaces, bracelets or watch-
straps when working on the battery. The metal parts
may induce a short circuit resulting in burns.
Dispose of used batteries separately from other
waste in the interests of environmental protection.

1.6 FLAMMABLE LIQUIDS
When handling flammable liquids:
Z do not smoke;
Z keep away from unshielded light sources and na-
ked flames.
Fuels often have a low flash point and are readily ig-
nited.
Never attempt to extinguish burning liquids with wa-
ter. Use:
Z dry powder;
Z with carbon dioxide;
Z with foam.
Water used for extinguishing purposes would vapor-
ize instantaneously on contact with burning sub-
stances and spread burning oil, for example, over a
wide area. Water generates short circuits in the elec-
trical system, possibly producing new hazards.
Stay away from open flames during refilling of hy-
draulic oil or fuel.
Fuel or oil splashes can cause slipping and therefore
accidents; clean immediately and accurately the ar-
eas eventually smeared.
Always tighten the safety plugs of fuel tank and hy-
draulic oil tank firmly.
Never use fuel to clean the machine parts eventually
smeared with oil or dust.
Use a non-inflammable product for cleaning parts.
Always perform fuel or oil refilling in well aired and
ventilated areas.
During refuelling hold the pistol firmly and keep it al-
ways in contact with the filler neck until the end of the
refuelling, to avoid sparkles due to static electricity.
Do not overfill the tank but leave a space for fuel ex-
pansion.
Never re-fuel when the engine is running.
Take all the necessary safety measures when weld-
ing, grinding or when working near a naked flame.

1.7 TYRES
Before inflating the tyres, always check the condition
of rims and the outer condition of tyres to find out the
presence of dents, cuts, tears of reinforcement plies
or other faults. Before inflating a tyre, make sure that
there are no nearby persons, then position yourself
at tread side.
Make sure that the inflating pressure of tyres is the
same prescribed by manufacturer and that the pres-
sure of the right tyre corresponds to the pressure of
the left tyre.
Never use reconditioned rims because possible
welds, heat treatments or brazings not performed
correctly can weaken the wheels and cause follow-
ing damages or failures. Deflate the tyres before
their disassembly.
Before taking out possible jammed objects from the
rims, it is necessary to deflate the tyres. Inflate tyres
by means of a pistol complete with extension and
pressure switch of control.
1.8 CLEANING
Clean the exterior of all components before carrying
out any form of repair. Dirt and dust can reduce the
efficient working life of a component and lead to
costly replacement.
Solvents should be checked that they are suitable
for the cleaning of components and also that they do
not risk the personal safety of the user.
Dirt from oil or grease and scattered tools or faulty
pieces are dangerous for persons, because they can
generate slipping or falls.
For the machine cleaning, use a jet of warm water or
steam under pressure and commercial detergents.
Never use fuel, petroleum or solvents, because the
first ones leave an oily layer that favours the sticking
of dust, while solvents (even if weak) damage the
paint and favour the formation of rust.
Never use water jets or steam on sensors, connec-
tors or other electric components.
Prevent that the water jet penetrates inside the cab.

1.9 WASTE DISPOSAL
Improperly disposing of waste can threaten the envi-
ronment.
Each country has its own Regulations on this sub-
ject. It is therefore advisable to prepare suitable con-
tainers to collect and store momentarily all solid and
fluid materials that must not be scattered in the envi-
ronment to avoid pollution.
At preset intervals these products will be delivered to
disposal stations legally recognized and present in
this Country.
Hereunder are listed some products of the machine
requiring disposal:
Z lubricating oil;
Z brakes system oil;
Z coolant mixture, condensation rests and pure anti-
freeze;
Z fuel;
Z filter elements, oil and fuel filters;
Z filter elements, air filters;
Z battery.
Also polluting rags, paper, sawdust and gloves must
be disposed in compliance with the same proce-
dures.
Do not use food or beverage containers that may
mislead someone into drinking from them. Do not
pour waste onto the ground, down a drain, or into
any water source. Air conditioning refrigerants es-
caping into the air can damage the Earth’s atmos-
phere. Government regulations may require a
certified air conditioning service centre to recover
and recycle used air conditioning refrigerants. Ob-
tain information on the proper way to recycle or dis-
pose of waste from your local environmental or
recycling centre, or from your Dealer.

2. USE INSTRUCTION
The machine must be used in accordance with its
designated use, by observing the safety and precau-
tionary rules and by strictly following the use instruc-
tions.
The excavator equipped with front attachment,
standard bucket or clamshell, is designed solely for
excavating, turning over and loading excavated
soils, sand, gravel, blasted rock, ore, coal and other
raw materials.
S DANGER
Using the excavator or its attachments for purposes
other than those stated above, e.g.:
Z for lifting or transporting persons;
Z as a working platform;
Z for lifting crane loads without the attachment being
approved for this purpose;
Z for pulling slung loads;
Z for driving in posts, supports, sheet-piles, without
the attachment being approved for this purpose;
is considered contrary to the designated use.
Improper use may cause injuries or a life-threatening
risk for the operator and for other persons and may
cause extensive damage to things.
Any functional disorders, especially those affecting
the safety of the machine, should therefore be recti-
fied immediately.
The manufacturer/supplier cannot be held responsi-
ble for damages resulting from improper use. The
risk involved in such misuse lies entirely with the us-
er.

2.1 MACHINE SAFETY
Before carrying out any service or repair work the
machine must be secured as follows:
Park the machine on a level and firm surface.
Rest the working attachment on the ground.
Lower the blade and the stabilizers to the ground.
Lock the upper structure.
Engage the parking brake.
Shut off the engine.
Move both hydraulic control levers in all directions,
to release possible residual pressure inside the hy-
draulic system.
Disconnect the pilot control.
Set the ignition key to position “0” and pull it out.
Secure the machine with wheel chocks as to prevent
its rolling or overturning.
2.2 ADJUST THE SEAT
A seat poorly adjusted for operator or work require-
ments may quickly fatigue the operator leading to
improper operations.
The seat should be adjusted whenever machine op-
erator changes.
The operator should be able to press the pedals
completely and to move the hydraulic control levers
correctly, with his back resting against the seat back.
On machines equipped with seat belt:
Z check the seat belt condition. In the event of dam-
age or after an accident, have it replaced immedi-
ately;
Z fasten seat belt before starting to work.

2.3 NOISE LEVELS
Sound power level (acoustic external)
LWA:
MH City Models: 101 dB (A)
MH Plus Models: 102 dB (A)
MH 5.6 Models: 103 dB (A)
Sound power level guaranteed, determined in com-
pliance with European standard 2000/14/EC.
Sound pressure level in the operator’s seat
(acoustic internal)
LpA:
MH City Models: 74 dB (A)
MH Plus Models: 77 dB (A)
MH 5.6 Models: 78 dB (A)
Sound pressure level continuous, measured inside
the cab with door and windows closed and with the
heater/air conditioner blower operating at 2nd speed,
measured on an identical machine, in compliance
with ISO 6396:1992 Standard.

2.4 TRAVEL ON PUBLIC ROADS
S WARNING
Road circulation (on public roads) is ruled by special
provisions varying from country to country. Check
beforehand with local authorities for circulation
provisions.
Transfer on public roads (each time you leave a
yard) is allowed only with an approved configuration,
complying with dimensions (A), (B) as shown on the
tables.
MH City
MONOBOOM
Dipper
mm
(in)
2600
(102.36)
2300
(90.55)
2000
(78.74)
A Maximum height
mm
(in)
3930
(154.72)
3870
(152.36)
3915
(154.13)
B Frontal off-set
mm
(in)
4080
(160.63)
4095
(161.22)
4080
(160.63)
PLACING BOOM
Dipper
mm
(in)
2600
(102.36)
2300
(90.55)
2000
(78.74)
A Maximum height
mm
(in)
4000
(157.48)
3955
(155.71)
3950
(155.51)
B Frontal off-set
mm
(in)
2685
(105.71)
2750
(108.28)
2910
(114.58)
OFF-SET BOOM
Dipper
mm
(in)
2000
(78.74)
A Maximum height
mm
(in)
4000
(157.48)
B Frontal off-set
mm
(in)
4130
(162.60)

MH Plus
MONOBOOM
Dipper
mm
(in)
2900
(114.17)
2600
(102.36)
2300
(90.55)
A Maximum height
mm
(in)
3980
(156.69)
3965
(156.10)
3965
(156.10)
B Frontal off-set
mm
(in)
4200
(165.35)
4215
(165.94)
4225
(166.34)
PLACING BOOM
Dipper
mm
(in)
2600
(102.36)
2300
(90.55)
-
A Maximum height
mm
(in)
3925
(154.53)
3925
(154.53)
-
B Frontal off-set
mm
(in)
2605
(102.56)
2680
(105.51)
-
OFF-SET BOOM
Dipper
mm
(in)
2000
(78.74)
A Maximum height
mm
(in)
4000
(157.48)
B Frontal off-set
mm
(in)
4130
(162.60)
MH 5.6
MONOBOOM
Dipper
mm
(in)
2800
(110.24)
2400
(94.49)
2000
(78.74)
A Maximum height
mm
(in)
3850
(151.57)
3800
(149.60)
3800
(149.60)
B Frontal off-set
mm
(in)
4750
(187.00)
4750
(187.00)
4850
(190.94)
PLACING BOOM
Dipper
mm
(in)
2400
(94.49)
2000
(78.74)
-
A Maximum height
mm
(in)
4000
(157.48)
4000
(157.48)
-
B Frontal off-set
mm
(in)
2800
(110.24)
2750
(108.28)
-

1. SWITCHES AND PUSH-BUTTONS ............................................................................................................. 1
2. CONTROLS AND PEDALS .......................................................................................................................... 6
3. MULTI-FUNCTION DISPLAY ..................................................................................................................... 10
SECTION 02 - CONTROLS AND
INSTRUMENTS

SECTION 02 - CONTROLS AND INSTRUMENTS 1
1. SWITCHES AND PUSH-BUTTONS

2 SECTION 02 - CONTROLS AND INSTRUMENTS
Ref. Description Operation Symbol
1
Rotary knob/
selector
Blower
Activates the blower and has 3-speed stages: 1,
2, 3.
2 White button
Air conditioner
(optional)
Activates/deactivates the air recirculation.
3 Blue button
Air conditioner
(optional)
Activation/deactivation of air conditioner (ON/
OFF).
4
Rotary knob/
selector
Heating
Sets the heating power:
completely to the left - low heating power (blue);
completely to the right - high heating power (red).
5 Push-button
Stabilizer
(optional)
Rear right stabilizer control.
6 Push-button
Stabilizer
(optional)
Rear left stabilizer control.
7 Push-button
Stabilizer
(optional)
Front left stabilizer control.
Blade (optional) Blade control.
8 Push-button
Stabilizer
(optional)
Front right stabilizer control.
9 Switch Parking brake Parking brake control.
10 Push-button
Floating axle
blocking
By pressing the symbol (lamp lights up) the
floating axle is blocked.
By pressing the symbol again (lamp turns off) the
floating axle is released.
11 Push-button Not used.

12 Push-button Road travel
Selects the road travel mode.
Ensure that the safety lever is placed to position
“0”.
13 Push-button Creep speed
By pressing the symbol (the lamp lights up) the
creep speed engages.
By pressing the symbol again (the lamp turns off)
and the creep speed disengages.
14 Display Multi-function Controls and monitoring of the machine functions.
15 Switch
Clamshell
opening/closing
The opening/closing speed of the clamshell is
determined by pre-set values. The speed
reduction is optional.
16 Switch
Hydraulic Shears
(optional)
To activate depress switch face without symbol.
To deactivate depress symbol face of switch.
17 Switch
Hydraulic rotary
cutter (optional)
18 Switch
Hydraulic
hammer
(optional)
19 Switch
Rotary light
(optional)
20 Ignition key
Activates and deactivates the electrical system.
Starting/Stopping the engine.
21 Switch
Rear working
floodlamps
(optional)
To activate, press the switch face without symbol.
To deactivate, press the symbol face of switch.
22 Switch
Cab floodlamps /
attachment
To activate, press the switch face without symbol.
To deactivate, press the symbol face of switch.
23 Switch
Screen wiper/
washer
Automatic return push-button.
One click: a wiper stroke and a liquid jet.
Activates the screen-washer pump and the wiper
as long as the switch face without symbol is kept
depressed.

24 Switch Windscreen wiper
Automatic return push-button.
One click: intermittent wiping.
As long as the switch is kept pressed the screen-
wiper operates continuously.
25 Push-button Engine rpm Lowering of engine rpm up to idle run in 7 stages.
26 Push-button Engine rpm
Engine rpm increase up to a maximum speed in 7
steps (7 power stages with fixed speed levels).
27 Push-button Auto Idle
Activation/deactivation of automatic engine speed
reduction.
After activation, the speed of the diesel engine is
automatically reduced to a lower speed during no-
work phases lasting longer than 4 seconds.
28 Push-button Low Idle
Sets engine to idling speed. If Auto Idle and Low
Idle are on at the same time, Low-Idle has higher
priority.
29 Push-button Gearbox
Push-button with two lights.
Left light on and right light out: 1st speed
engaged.
Left light out and right light on: 2nd speed
engaged.
Lights off: the automatic gearshift mode is active.
30 Push-button
Upper structure
holding brake
Lights off: brake released, upper structure free to
turn.
Left light on: holding brake engaged, upper
structure braked.
Right light on: holding brake automatic mode.
Holding brake is applied and released
automatically. As soon as the upper structure
stops the brake applies.

31 Push-button
Overload
(optional)
Lights off: overload warning system off.
Left light on: overload warning system on
(machine not additionally stabilized).
Right light on: overload warning system on
(machine additionally stabilized).
32 Push-button
Upper structure
holding brake
Lights off: soft braking of upper structure rotation.
Left light on: standard braking of upper structure
rotation.
Lights on: abrupt braking of upper structure
rotation.
33 Switch
Quick coupler
(optional)
Stabilizer
independent
activation
(optional)
Stabilizer independent raising/lowering.
34 Switch 2nd pump
Once this option is set, to button (25) is assigned
a different function.

2. CONTROLS AND PEDALS
1
Left hydraulic
control lever
Rotation
By shifting the lever to the right - the upper
structure rotates to the right.
By shifting the lever to the left - the upper
structure rotates to the left.
Dipper/blade and
stabilizers
By shifting the lever forward - the dipper extends -
the blade/stabilizers lower.
By shifting the lever backward - the dipper retracts
- the blade/stabilizers raise.
2 Push-button Levelling
Allows to perform the levelling operation in an
accurate and smooth way.
3 Safety lever Pilot control
By shifting the lever upward the pilot control is
OFF.
By shifting the lever downward the pilot control is
ON.

4 Push-button
Power Boost
Generates an engine rpm and pressure increase
(for short work stages).
Independent
stabilizers
(optional)
Allows to raise the stabilizers independently one
from another.
5 Push-button
Dipper/blade and
stabilizers
controls switch-
over
The controls for dipper/blade and stabilizers
switch over. (With blade/stabilizers activated the
buzzer sounds).
Independent
stabilizers
(optional)
Allows to lower the stabilizers independently one
from another.
6 Push-button
Hydraulic
hammer
Hydraulic hammer engagement.
7 Push-button
Clamshell
rotation (optional)
Left clamshell rotation.
8 Pedal
Placing boom/
attachment
With placing boom: extension/retraction of boom
adjusting cylinder.
With hammer: hammer control.
With rotary cutter: rotary cutter control.
With shears: shears control.
Off-set digging
By depressing pedal on the upper side: the off-set
boom turns to the right.
By depressing the pedal on the bottom side: the
off-set boom turns to the left.
9 Footrest
10 Lever Lights
It selects the lights type.
Main beams signal: by pushing the lever upward.
Low beams: lever in middle position.
Main beams: by pushing the lever downward.
11 Lever Horn Acoustic signal.
12 Lever Lights Lights off.

13 Lever Lights Tail lights on.
14 Lever Lights Low beams on.
15 Lever Turn signal light Left signal light activation.
16 Lever Turn signal light Right signal light activation.
17 Push-button Flashing lights Flashing lights activation.
18
Steering wheel
and column
Steering Transfers the steering motion to the steering axle.
19 Lever
Locking of the
steering column
It locks the steering column to required inclination:
by pushing downward - the column can be
moved;
by releasing the lever - the column is locked.
20 Pedal Travel
Starts the machine travel and determines its
speed.
21 Pedal Service brake
It brakes the machine travel. The control lever
locks the service brake to braking position. At the
same time, the floating axle blocks. When the
brake pedal is released, also the floating axle
releases automatically.
22 Push-button
Clamshell
rotation (optional)
Right clamshell rotation.
23 Push-button Horn Acoustic signal.
24 Push-button Travel direction Selection of forward travel direction.
25 Push-button Travel direction Selection of reverse travel direction.

26 Push-button Travel direction Selection of idle run.
27 Pin
Upper structure
holding brake
It locks the upper structure to the undercarriage.
28
Right hydraulic
control lever
Boom
By shifting the lever forward - the boom lowers.
By shifting the lever backward - the boom raises.
Bucket
By pushing the lever to the right - the bucket
dumps.
By pushing the lever to the left - the bucket fills.
Clamshell
(optional)
By pushing the lever to the right - the clamshell
opens.
By pushing the lever to the left - the clamshell
closes.
29 Socket 12 V auxiliary socket.

3. MULTI-FUNCTION DISPLAY
1 Lamp Travel direction
This light turns on when the forward
travel is engaged.
2 Lamp Turn signal light
It flashes when the left turn signal is
activated.
3 Lamp Preheating It turns on during preheating.
4 Lamp Main beams
It turns on blue, when the main
beams are activated.
5 Lamp
Upper structure
holding brake
This light turns on when the holding
brake is engaged.
6 Lamp Turn signal light
It turns on when the right turn signal
is activated.

7 Lamp Travel direction
It turns on when the reverse travel is
activated.
8 Display
Time/Hourmeter/
Fuel level
Time in hours and minutes/machine
working hours display/fuel level
indication.
Indication above the cross line =
Level OK
Indication under the cross line = top
up fuel.
Time/Engine
power level
Time in hours and minutes / graphic
display of the engine power level.
Coolant
temperature/
hydraulic oil
temperature
It displays the temperature of coolant
and the hydraulic oil temperature.
Secret code
Input of secret code for the start-up
electronic lock.
Operation hours
Display of service hours, according
to:
Z total hours;
Z partial time;
Z days count.
121 HOURS
CODE
OPERATION HOURS

8 Display
Attachments
Setting of hydraulic oil pressure and
of volumetric flow for the following
attachments:
Z 4 different hydraulic hammers;
Z 4 different rotary cutters;
Z 4 different hydraulic shears.
Further options can be activated by
the dealer for use by the operator:
Z degree of damping for equipment
movements and travel function;
Z rotation power limiting;
Z activation of “Auto Power Boost”
function;
Z setting of the levelling function;
Z basic setting;
Z clamshell rotation;
Z boom adjusting cylinder speed.
Display
Setting of display contrast and
brightness, clock, language and
measuring units.
Information
Displays operating data of the
machine and the control system.
Machine Display of all machine data.
ATTACHMENTS
DISPLAY
INFORMATION
MACHINE

8 Display
Maintenance
Display of operating hours by
function groups of the machine
(disabled in normal machine
operation).
Display and setting of maintenance
intervals (disabled in normal
machine operation).
Calibration of machine functions
(reserved for Service Department).
Activation of optional machine
functions (disabled in normal
machine operation).
Resetting of faults (reserved for
Service Department - password
protected).
Faults
Faults occurred are stored in detail
by electronic control unit.
This menu is reserved for our
Service and disabled in normal
machine operation (password
protected).
9 Push-button “set” button
Push-button for selection and
confirmation of items in function and
navigation menus.
10 Push-button
Push-button with
downward arrow
Push-button for selection and scroll-
down in function and navigation
menus.
11 Push-button
Push-button with
upward arrow
Push-button for selection and scroll-
up or escape button in function and
navigation menus.
MAINTENANCE
FAULTS RETRIEVAL

12 Lamp
Multi-function
display
It lights up yellow: concurrently to
warning signal, to indicate
unimportant faults concerning the
safety and the operation.
By pressing “Set”, the fault is
displayed.
If several faults have occurred, they
are displayed one after the other.
Not all yellow faults are displayed on
the display.
A detailed list of yellow faults is
accessible via the Fault Recall
menu, but it is reserved to the After-
sales service.
13 Lamp
Multi-function
display
It lights up red: when the safety of
persons and the operation of the
machine’s main assemblies is
endangered.
The fault digital code is displayed
concurrently and an acoustic signal
is released.
In some fault cases, certain machine
functions can be switched on by
emergency operation.
There is also the possibility of
several faults being indicated at the
same time.

1. MAIN COMPONENTS .................................................................................................................................. 1
2. DIMENSIONS - OPERATING WEIGHTS ..................................................................................................... 3
3. DIGGING PERFORMANCE ....................................................................................................................... 19
4. LIFTING CAPACITIES................................................................................................................................ 33
5. HYDRAULIC SYSTEM ............................................................................................................................... 39
6. ROTATION ................................................................................................................................................. 40
7. TRAVEL...................................................................................................................................................... 41
8. TYRES........................................................................................................................................................ 42
9. BRAKES ..................................................................................................................................................... 42
10. STEERING................................................................................................................................................ 42
11. ELECTRICAL SYSTEM............................................................................................................................ 42
12. BUCKETS................................................................................................................................................. 43
13. TIGHTENING TORQUES ......................................................................................................................... 44
14. CENTRALIZED LUBRICATION PUMP (OPTIONAL)............................................................................... 44
15. FUEL SYSTEM......................................................................................................................................... 44
16. ENGINE .................................................................................................................................................... 45
17. SUPPLY SUMMARIZING CHART............................................................................................................ 46
SECTION 03 - TECHNICAL
SPECIFICATIONS

SECTION 03 - TECHNICAL SPECIFICATIONS 1
1. MAIN COMPONENTS
1.1 OUTFIT WITH PLACING BOOM
1. Bucket
2. Bucket cylinder
3. Dipper
4. Batteries
5. Dipper cylinder
6. Placing boom
7. Multi-cooler
8. Boom cylinders
9. Boom
10. Boom adjusting cylinder
11. Muffler
12. Diesel engine
13. Hydraulic oil tank
14. Hydraulic pumps
15. Fuel tank
16. Counterweight
17. Stabilizers
18. Rear wheels
19. Rear axle
20. Cab
21. Stair and storage box
22. Front wheels
23. Front steering axle
24. Axle floating locking cylinders
25. Blade
26. Undercarriage
27. Upper structure

2 SECTION 03 - TECHNICAL SPECIFICATIONS
1.2 OUTFIT WITH MONOBOOM
1. Bucket
2. Bucket cylinder
3. Dipper
4. Batteries
5. Dipper cylinder
6. Monoboom
7. Multi-cooler
8. Boom cylinders
10. Muffler
11. Diesel engine
12. Hydraulic oil tank
13. Hydraulic pumps
14. Fuel tank
15. Counterweight
16. Stabilizers
17. Rear wheels
18. Rear axle
19. Cab
20. Stair and storage box
21. Front wheels
22. Front steering axle
23. Axle floating locking cylinders
24. Blade
25. Undercarriage
26. Upper structure

2. DIMENSIONS - OPERATING WEIGHTS
2.1 MH City MODELS
OUTFIT WITH PLACING BOOM

G = tyres maximum width
O = machine maximum width
* = dimension determined with twin-tyres 10.00-20
With twin tyres 315/80-22.5.................................................................................................. 2535 mm (99.80 in)
With single tyres 18R-19.5................................................................................................... 2500 mm (98.42 in)
With single tyres 600/40-22.5................................................................................................ 2490 mm(98.03 in)
mm
Dipper A B C D E F G* H I L M N O P Q R
2000 2550 430 1220 1750 300 2840 2520 3010 3900 345 4555 930 2540 1070 8035 8175
2300 2550 430 1220 1750 300 2890 2520 3010 3900 345 4560 930 2540 1070 8040 8180
2600 2550 430 1220 1750 300 3070 2520 3010 3900 345 4465 930 2540 1070 7945 8085
in
78.74 100.39 16.93 48.03 68.90 11.81 111.81 99.21 118.50 153.54 13.58 179.33 36.61 100.00 42.13 316.34 321.85
90.55 100.39 16.93 48.03 68.90 11.81 113.78 99.21 118.50 153.54 13.58 179.53 36.61 100.00 42.13 316.53 322.05
102.36 100.39 16.93 48.03 68.90 11.81 120.87 99.21 118.50 153.54 13.58 175.79 36.61 100.00 42.13 312.79 318.31
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers (kg) (lb)
Front blade and rear
stabilizers (kg) (lb)
2000 (78.74) 14795 (32549) 14765 (32483) 15235 (33517)
2300 (90.55) 14845 (32659) 14815 (32593) 15285 (33627)
2600 (102.36) 14895 (32769) 14865 (32703) 15335 (33737)

OUTFIT WITH MONOBOOM

* = dimension determined with single tyres 18R-19.5
With twin tyres 10.00-20.......................................................................................................2520 mm (99.21 in)
With single tyres 600/40-22.5............................................................................................... 2490 mm (98.03 in)
mm
2000 2550 500 1240 1750 320 2925 2500 3030 3900 360 4450 930 2540 1070 7930 8070
2300 2550 500 1240 1750 320 3190 2500 3030 3900 360 4480 930 2540 1070 7960 8100
2600 2550 500 1240 1750 320 3335 2500 3030 3900 360 4440 930 2540 1070 7920 8060
in
78.74 100.39 19.68 48.82 68.90 12.60 115.16 98.42 119.29 153.54 14.17 175.20 36.61 100.00 42.13 312.20 317.72
90.55 100.39 19.68 48.82 68.90 12.60 125.59 98.42 119.29 153.54 14.17 176.38 36.61 100.00 42.13 313.38 318.90
102.36 100.39 19.68 48.82 68.90 12.60 131.30 98.42 119.29 153.54 14.17 174.80 36.61 100.00 42.13 311.81 317.22
Dipper (mm) (in)
Rear blade
(kg) (lb)
2000 (78.74) 14300 (31460) 14270 (31394) 14740 (32428)
2300 (90.55) 14350 (31570) 14320 (31504) 14790 (32538)
2600 (102.36) 14400 (31680) 14370 (31614) 14840 (32648)

OUTFIT WITH OFF-SET BOOM

mm
2000 2550 500 1240 1750 320 2805 2500 3030 3900 360 5784 930 2540 1070 9264 9404
2300 2550 500 1240 1750 320 3101 2500 3030 3900 360 5865 930 2540 1070 9345 9485
2600 2550 500 1240 1750 320 3402 2500 3030 3900 360 5780 930 2540 1070 9260 9400
in
78.74 100.39 19.68 48.82 68.90 12.60 110.43 98.42 119.29 153.54 14.17 227.72 36.61 100.00 42.13 364.72 370.23
90.55 100.39 19.68 48.82 68.90 12.60 122.09 98.42 119.29 153.54 14.17 230.90 36.61 100.00 42.13 367.91 373.42
102.36 100.39 19.68 48.82 68.90 12.60 133.94 98.42 119.29 153.54 14.17 227.56 36.61 100.00 42.13 364.57 370.08
Dipper (mm) (in)
Rear blade
(kg) (lb)
2000 (78.74) 14816 (32595) 14786 (32529) 15256 (33563)
2300 (90.55) 14866 (32705) 14836 (32639) 15306 (33673)
2600 (102.36) 14916 (32815) 14886 (32749) 15356 (33783)

2.2 MH Plus MODELS

* = dimension determined with twin-tyres 10.00-20
With single tyres 600/40-22.5..............................................................................................2490 mm (98.03 in)
mm
2300 2550 430 1220 1900 300 2920 2520 3010 3900 395 4810 930 2540 1070 8290 8430
2600 2550 430 1220 1900 300 2980 2520 3010 3900 345 4820 930 2540 1070 8300 8440
2900 2550 430 1220 1900 300 3045 2520 3010 3900 345 4805 930 2540 1070 8285 8425
in
90.55 100.39 16.93 48.03 74.80 11.81 114.96 99.21 118.50 153.54 15.55 189.37 36.61 100.00 42.13 326.38 331.89
102.36 100.39 16.93 48.03 74.80 11.81 117.32 99.21 118.50 153.54 13.58 189.76 36.61 100.00 42.13 326.77 332.28
114.17 100.39 16.93 48.03 74.80 11.81 119.88 99.21 118.50 153.54 13.58 189.17 36.61 100.00 42.13 326.18 331.69
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers
(kg) (lb)
Front blade and
rear stabilizers
(kg) (lb)
Front and rear
stabilizers
(kg) (lb)
2300 (90.55) 17470 (38434) 17480 (38456) 17900 (39380) 18400 (40480)
2600 (102.36) 17510 (38522) 17520 (38544) 17940 (39468) 18440 (40568)
2900 (114.17) 17560 (38632) 17570 (38654) 17990 (39578) 18490 (40678)

mm
2300 2550 450 1240 1900 320 2905 2500 3030 3900 365 4545 930 2540 1070 8025 8165
2600 2550 450 1240 1900 320 3130 2500 3030 3900 365 4615 930 2540 1070 8095 8235
2900 2550 450 1240 1900 320 3400 2500 3030 3900 365 4550 930 2540 1070 8030 8170
in
90.55 100.39 17.72 48.82 74.80 12.60 114.37 98.42 119.29 153.54 14.37 178.94 36.61 100.00 42.13 315.94 321.46
102.36 100.39 17.72 48.82 74.80 12.60 123.23 98.42 119.29 153.54 14.37 181.69 36.61 100.00 42.13 318.70 324.21
114.17 100.39 17.72 48.82 74.80 12.60 133.86 98.42 119.29 153.54 14.37 179.13 36.61 100.00 42.13 316.14 321.65
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers
(kg) (lb)
Front blade and
rear stabilizers
(kg) (lb)
Front and rear
stabilizers
(kg) (lb)
2300 (90.55) 16790 (36398) 16800 (36960) 17220 (37884) 17720 (38984)
2600 (102.36) 16830 (37026) 16840 (37048) 17260 (37972) 17760 (39072)
2900 (114.17) 16880 (37136) 16890 (37158) 17310 (38082) 17810 (39182)

mm
2300 2550 450 1240 1900 320 2903 2500 3030 3900 365 5919 930 2540 1070 9399 9534
2600 2550 450 1240 1900 320 3126 2500 3030 3900 365 5988 930 2540 1070 9468 9608
2900 2550 450 1240 1900 320 3403 2500 3030 3900 365 5924 930 2540 1070 9404 9544
in
90.55 100.39 17.72 48.82 74.80 12.60 114.29 98.42 119.29 153.54 14.37 233.03 36.61 100.00 42.13 370.04 375.35
102.36 100.39 17.72 48.82 74.80 12.60 123.07 98.42 119.29 153.54 14.37 235.75 36.61 100.00 42.13 372.75 378.28
114.17 100.39 17.72 48.82 74.80 12.60 133.98 98.42 119.29 153.54 14.37 233.23 36.61 100.00 42.13 370.23 375.75
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers
(kg) (lb)
Front blade and
rear stabilizers
(kg (lb)
Front and rear
stabilizers
(kg) (lb)
2300 (90.55) 17452 (38394) 17462 (38416) 17882 (39340) 18382 (40440)
2600 (102.36) 17492 (38482) 17502 (38504) 17922 (39428) 18422 (40528)
2900 (114.17) 17542 (38592) 17552 (38614) 17972 (39538) 18472 (40638)

2.3 MH 5.6 MODELS

mm
2000 2550 450 1240 1900 320 2905 2500 3030 3900 365 4545 930 2540 1070 8025 8165
2400 2550 450 1240 1900 320 3130 2500 3030 3900 365 4615 930 2540 1070 8095 8235
2800 2550 450 1240 1900 320 3400 2500 3030 3900 365 4550 930 2540 1070 8030 8170
in
78.74 100.39 17.72 48.82 74.80 12.60 114.37 98.42 119.29 153.54 14.37 178.94 36.61 100.00 42.13 315.94 321.46
94.49 100.39 17.72 48.82 74.80 12.60 123.23 98.42 119.29 153.54 14.37 181.69 36.61 100.00 42.13 318.7 324.21
110.24 100.39 17.72 48.82 74.80 12.60 133.86 98.42 119.29 153.54 14.37 179.13 36.61 100.00 42.13 316.14 321.65
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers
(kg) (lb)
Front blade and
rear stabilizers
(kg) (lb)
Front and rear
stabilizers
(kg) (lb)
2000 (78.74) 19180 (42196) 19230 (42306) 19810 (43582) 20270 (44594)
2400 (94.49) 19240 (42328) 19290 (42438) 19880 (43736) 20340 (44748)
2800 (110.24) 19330 (42526) 19390 (42658) 19970 (43934) 20430 (44946)

With twin tyres 11.00-20..................................................................................................... 2545 mm (100.20 in)
mm
2000 2650 390 1270 2050 320 3000 2500 3090 3900 350 5015 1010 2540 1040 8675 8705
2400 2650 390 1270 2050 320 2990 2500 3090 3900 350 5000 1010 2540 1040 8660 8690
2800 2650 390 1270 2050 320 3090 2500 3090 3900 350 5030 1010 2540 1040 8690 8720
in
78.74 104.33 15.35 50.00 80.71 12.60 118.11 98.42 121.65 153.54 13.78 197.44 39.76 100.00 40.94 341.53 342.72
94.49 104.33 15.35 50.00 80.71 12.60 117.72 98.42 121.65 153.54 13.78 196.85 39.76 100.00 40.94 340.94 342.12
110.24 104.33 15.35 50.00 80.71 12.60 121.65 98.42 121.65 153.54 13.78 198.03 39.76 100.00 40.94 342.12 343.31
Dipper (mm) (in)
Rear blade
(kg) (lb)
Rear stabilizers
(kg) (lb)
Front blade and
rear stabilizers
(kg) (lb)
Front and rear
stabilizers
(kg) (lb)
2000 (78.74) 18370 (40414) 18415 (40513) 18995 (41789) 19455 (42801)
2400 (94.49) 18430 (40546) 18475 (40645) 19065 (41943) 19525 (42955)
2800 (110.24) 18520 (40744) 18575 (40865) 19155 (42141) 19615 (43153)

3. DIGGING PERFORMANCE
3.1 MH City MODELS
Dipper mm in 2000 78.74 2300 90.55 2600 102.36
A Maximum digging height mm in 9200 362.20 9300 366.14 9600 377.95
B Maximum loading height mm in 6800 267.70 6900 271.65 7100 279.53
C Maximum digging depth mm in 4800 188.98 5100 200.79 5400 212.60
D Maximum vertical wall digging depth mm in 3100 122.05 3500 137.79 3800 149.61
E
Maximum digging depth of cut for level
bottom (L = 2438 mm (95.98 in))
mm in 4700 185.04 4900 192.91 5200 204.72
F Maximum digging reach mm in 8300 326.77 8600 338.58 8800 346.46
G Maximum digging reach at ground mm in 8100 318.90 8400 330.71 8600 338.58
H Minimum swing radius mm in 2700 106.30 2600 102.36 2700 106.30
K
Maximum loading height
(dipper retracted)
mm in 3300 129.92 3000 118.11 2700 106.30
F1 Bucket tensile force (370 bar (5366 psi)) kN lbf 96.2 21626.6 96.2 21626.6 96.2 21626.6
F2 Dipper tensile force (370 bar (5366 psi)) kN lbf 67.3 15129.6 61.6 13848.2 56.8 12769.1

Dipper mm in 2000 78.74 2300 90.55 2600 102.36
E
bottom (L = 2438 mm (95.98 in))
mm in 4600 181.10 4800 188.98 5200 204.72
K
Maximum loading height (dipper
retracted)
mm in 2800 110.24 2500 98.42 2200 86.51

Dipper mm in 2000 78.74 2300 90.55 2600 102.36
C' Maximum off-set boom depth mm in 1500 59.05 1800 70.87 2100 82.68
E
bottom (L = 2438 mm (95.98 in))
mm in 4500 177.16 4800 188.98 5100 200.79
K Maximum loading height (dipper retracted) mm in 2900 114.17 2600 102.36 2300 90.55
Or Off-set right side mm in 2600 102.36 2600 102.36 2600 102.36
Ol Off-set left side mm in 2400 94.49 2400 94.49 2400 94.49
Xr Off-set angle right side ° 42 42 42
Xl Off-set angle left side ° 43 43 43

OUTFIT WITH CLAMSHELL BUCKET
Placing boom
Dipper mm in 2000 78.74 2300 90.55 2600 102.36
A Maximum loading height mm in 5600 220.47 5700 224.41 6000 236.22
C Maximum depth mm in 5900 232.28 6200 244.09 6500 255.90
F Maximum outreach mm in 7100 279.53 7300 287.40 7600 299.21
H Front swing radius mm in 2300 90.55 2200 86.61 2300 90.55
K Minimum loading height mm in 2100 82.68 1800 70.87 1500 59.05

Monoboom
Dipper mm in 2000 78.74 2300 90.55 2600 102.36

3.2 MH Plus MODELS
Dipper mm in 2300 90.55 2600 102.36 2900 114.17
E
bottom (L = 2438 mm (95.98 in))
mm in 5300 208.66 5700 224.41 6000 235.22
K
retracted)
mm in 3100 122.05 2800 110.24 2500 98.42
F2 Dipper tensile force (370 bar (5366 psi)) kN lbf 70.7 15894 65.4 14702.5 60.7 13645.9

Dipper mm in 2300 90.55 2600 102.36 2900 114.17
E
bottom (L = 2438 mm (95.98 in))
mm in 5200 204.72 5500 216.53 5800 228.35
K
retracted)
mm in 2600 102.36 2300 90.55 2000 78.74

Dipper mm in 2300 90.55 2600 102.36 2900 114.17
C' Maximum off-set boom depth mm in 2200 86.62 2500 98.42 2800 110.24
E
bottom (L = 2438 mm (95.98 in))
mm in 5100 200.79 5400 212.60 5700 224.41
K Maximum loading height (dipper retracted) mm in 2600 102.36 2400 94.49 2100 82.68
Or Off-set right side mm in 3000 118.11 3000 118.11 3000 118.11
Ol Off-set left side mm in 2800 110.24 2800 110.24 2800 110.24
Xr Off-set angle right side ° 48 48 48
Xl Off-set angle left side ° 48 48 48

Placing boom
Dipper mm in 2300 90.55 2600 102.36 2900 114.17

Monoboom
Dipper mm in 2300 90.55 2600 102.36 2900 114.17

3.3 MH 5.6 MODELS
Dipper mm in 2000 78.74 2400 94.49 2800 110.24
E
bottom (L = 2438 mm (95.98 in))
mm in 5300 208.66 5700 224.41 6100 240.16
K
retracted)
mm in 2800 110.24 2900 114.17 3000 118.11

Dipper mm in 2000 78.74 2400 94.49 2800 110.24
E
bottom (L = 2438 mm (95.98 in))
mm in 5100 200.79 5500 216.53 5900 232.28
K
retracted)
mm in 3100 122.05 2700 106.30 2300 90.55

Placing boom
Dipper mm in 2000 78.74 2400 94.49 2800 110.24

Monoboom
Dipper mm in 2000 78.74 2400 94.49 2800 110.24

4. LIFTING CAPACITIES
4.1 MH City MODELS
A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.0 m
(6.56 ft)
Z2
5.9
(19.36)
3.6
(11.81)
2.4
(7.87)
5.9
(19.36)
3.6
(11.81)
2.9
(9.51)
5.9
(19.36)
3.6
(11.81)
3.6
(11.81)
5.9
(19.36)
3.6
(11.81)
3.6
(11.81)
5.7
(18.70)
3.2
(10.50)
2.1
(6.89)
Z1
5.9
(19.36)
3.1
(10.17)
2.0
(6.56)
7.8
(25.59)
4.0
(13.12)
2.5
(8.20)
8.3
(27.23)
5.5
(18.04)
3.5
(11.48)
8.3
(27.23)
5.8
(19.03)
4.4
(14.44)
5.0
(16.40)
2.6
(8.53)
1.7
(5.58)
Z3
5.8
(19.03)
3.0
(9.84)
2.0
(6.56)
7.6
(34.93)
3.9
(12.79)
2.5
(8.20)
11.4
(37.40)
5.4
(17.72)
3.5
(11.48)
12.0
(39.37)
6.6
(21.65)
4.4
(14.44)
4.8
(15.75)
2.6
(8.53)
1.7
(5.58)
LD = 2.3 m
(7.55 ft)
Z2
4.4
(14.44)
3.2
(10.50)
2.3
(7.55)
1.5
(4.92)
4.4
(14.44)
3.2
(10.50)
2.5
(8.20)
1.9
(6.23)
4.4
(14.44)
3.2
(10.50)
2.5
(8.20)
1.9
(6.23)
4.4
(14.44)
3.2
(10.50)
2.5
(8.20)
1.9
(6.23)
4.4
(14.44)
3.2
(10.50)
2.0
(6.56)
1.3
(4.26)
Z1
5.9
(19.36)
3.1
(10.17)
2.0
(6.56)
1.4
(4.59)
7.8
(25.59)
4.0
(13.12)
2.5
(8.20)
1.8
(5.90)
8.5
(27.89)
5.5
(18.04)
3.4
(11.15)
1.9
(6.23)
8.5
(27.89)
5.5
(18.04)
4.3
(14.11)
1.9
(6.23)
5.0
(16.40)
2.6
(8.53)
1.7
(5.58)
1.2
(3.94)
Z3
5.7
(18.70)
3.0
(9.84)
2.0
(6.56)
7.5
(24.61)
3.8
(12.47)
2.5
(8.20)
9.0
(29.53)
5.4
(17.72)
3.4
(11.15)
9.0
(29.53)
7.0
(22.97)
4.3
(14.11)
4.7
(15.42)
2.5
(8.20)
1.7
(5.58)
LD = 2.6 m
(8.53 ft)
Z2
6.7
(21.98)
2.2
(7.22)
2.4
(7.87)
1.5
(4.92)
7.6
(24.93)
2.2
(7.22)
2.6
(8.53)
1.8
(5.90)
7.6
(24.93)
2.2
(7.22)
2.6
(8.53)
1.8
(5.90)
7.6
(24.93)
2.2
(7.22)
2.6
(8.53)
1.8
(5.90)
5.8
(19.03)
2.2
(7.22)
2.1
(6.89)
1.3
(4.26)
Z1
5.9
(19.36)
3.2
(10.50)
2.0
(6.56)
1.4
(4.59)
7.6
(24.93)
4.0
(13.12)
2.5
(8.20)
1.8
(5.90)
7.6
(24.93)
5.2
(17.06)
3.4
(11.15)
2.4
(7.87)
7.6
(24.93)
5.2
(17.06)
3.4
(11.15)
2.4
(7.87)
5.0
(16.40)
2.7
(8.86)
1.7
(5.58)
1.2
(3.94)
Z3
5.6
(18.37)
3.0
(9.84)
1.9
(6.23)
7.4
(24.28)
3.8
(12.47)
2.5
(8.20)
10.5
(34.45)
5.2
(17.06)
3.4
(11.15)
10.5
(34.45)
5.2
(17.06)
4.1
(13.45)
4.7
(15.42)
2.5
(8.20)
1.6
(5.25)

A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.0 m
(6.56 ft)
Z2
3.4
(11.15)
2.2
(7.22)
4.1
(13.45)
2.7
(8.86)
4.1
(13.45)
3.2
(10.50)
4.1
(13.45)
3.2
(10.50)
2.9
(9.51)
1.9
(6.23)
Z1
5.0
(16.40)
2.9
(9.51)
2.0
(6.56)
5.0
(16.40)
3.7
(12.14)
2.5
(8.20)
5.0
(16.40)
5.2
(17.06)
3.4
(11.15)
5.0
(16.40)
5.7
(18.70)
4.3
(14.11)
4.4
(14.44)
2.5
(8.20)
1.7
(5.58)
Z3
5.4
(17.72)
2.9
(9.51)
2.0
(6.56)
7.2
(23.62)
3.8
(12.47)
2.5
(8.20)
8.7
(28.54)
5.3
(17.39)
3.5
(11.48)
8.7
(28.54)
5.9
(19.36)
4.4
(14.44)
4.5
(14.76)
2.5
(8.20)
1.7
(5.58)
LD = 2.3 m
(7.55 ft)
Z2
6.4
(21.00)
3.4
(11.15)
1.8
(5.90)
8.2
(26.90)
4.3
(14.11)
1.8
(5.90)
8.2
(26.90)
4.5
(14.76)
1.8
(5.90)
8.2
(26.90)
4.5
(14.76)
1.8
(5.90)
5.4
(17.72)
3.0
(9.84)
1.8
(5.90)
Z1
4.7
(15.42)
2.9
(9.51)
2.0
(6.56)
4.7
(15.42)
3.7
(12.14)
2.5
(8.20)
4.7
(15.42)
5.2
(17.06)
3.4
(11.14)
4.7
(15.42)
5.4
(17.72)
4.3
(14.11)
4.4
(14.44)
2.4
(7.87)
1.7
(5.58)
Z3
5.3
(17.39)
2.9
(9.51)
2.0
(6.56)
7.0
(22.97)
3.7
(12.14)
2.5
(8.20)
7.0
(22.97)
5.2
(17.06)
3.4
(11.14)
7.0
(22.97)
6.3
(20.67)
4.3
(14.11)
4.4
(14.44)
2.4
(7.87)
1.7
(5.58)
LD = 2.6 m
(8.53 ft)
Z2
6.5
(21.32)
3.5
(11.48)
2.2
(7.22)
1.5
7.3
(23.95)
4.3
(14.11)
2.2
(7.22)
1.9
(6.23)
7.3
(23.95)
5.0
(16.40)
2.2
(7.22)
1.9
(6.23)
7.3
(23.95)
5.0
(16.40)
2.2
(7.22)
1.9
(6.23)
5.5
(18.04)
3.0
(9.84)
1.9
(6.23)
1.3
(4.26)
Z1
5.2
(17.06)
2.9
(9.51)
1.9
(6.23)
1.4
5.4
(17.72)
3.7
(12.14)
2.4
(7.87)
1.8
(5.90)
5.4
(17.72)
5.0
(16.40)
3.4
(11.15)
1.8
(5.90)
5.4
(17.72)
5.0
(16.40)
4.1
(13.45)
1.8
(5.90)
4.3
(14.11)
2.4
(7.87)
1.6
(5.25)
1.2
(3.94)
Z3
5.3
(17.39)
2.9
(9.51)
1.9
(6.23)
7.0
(22.97)
3.7
(12.14)
2.4
(7.87)
7.8
(25.59)
5.1
(16.73)
3.4
(11.15)
7.8
(25.59)
5.1
(16.73)
4.3
(14.11)
4.3
(14.11)
2.4
(7.87)
1.6
(5.25)

4.2 MH Plus MODELS
A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.3 m
(7.55 ft)
Z2
7.5
(24,51)
3.7
(12.14)
3.0
(9.84)
1.9
(6.23)
7.5
(24,51)
3.7
(12.14)
3.5
(11.48)
2.3
(7.55)
7.5
(24,51)
3.7
(12.14)
4.1
(13.45)
3.0
(9.84)
7.5
(24,51)
3.7
(12.14)
4.1
(13.45)
3.1
(10.17)
7.0
(22.97)
3.7
(12.14)
2.6
(8.53)
1.7
(5.58)
Z1
7.3
(23.95)
3.9
(12.79)
2.5
(8.20)
1.8
(5.90)
9.1
(29.85)
4.7
(15.42)
2.9
(9.51)
2.1
(6.89)
9.5
(31.17)
6.4
(21.00)
4.0
(13.12)
2.9
(9.51)
9.5
(31.17)
6.7
(21.98)
5.0
(16.40)
3.6
(11.81)
6.2
(20.34)
3.4
(11.15)
2.1
(6.89)
1.5
(4.92)
Z3
7.0
(22.97)
3.7
(12.14)
2.4
(7.87)
8.7
(28.54)
4.5
(14.76)
2.9
(9.51)
12.7
(41.67)
6.2
(20.34)
3.9
(12.79)
12.7
(41.67)
6.5
(21.32)
4.9
(16.08)
5.9
(19.36)
3.2
(10.50)
2.1
(6.89)
LD = 2.6 m
(8.53 ft)
Z2
4.9
(16.08)
3.9
(12.79)
2.9
(9.51)
1.9
(6.23)
4.9
(16.08)
3.9
(12.79)
3.1
(10.17)
2.3
(7.55)
4.9
(16.08)
3.9
(12.79)
3.1
(10.17)
2.4
(7.87)
4.9
(16.08)
3.9
(12.79)
3.1
(10.17)
2.4
(7.87)
4.9
(16.08)
3.9
(12.79)
2.6
(8.53)
1.7
(5.58)
Z1
7.3
(23.95)
4.0
(13.12)
2.5
(8.20)
1.7
(5.58)
9.1
(29.86)
4.8
(15.75)
3.0
(9.84)
2.1
(6.89)
9.7
(31.82)
6.3
(20.67)
4.0
(13.12)
2.8
(9.19)
9.7
(31.82)
6.3
(20.67)
4.9
(16.08)
3.5
(11.48)
6.2
(20.34)
3.4
(11.15)
2.1
(6.89)
1.5
(4.92)
Z3
7.0
(22.97)
3.7
(12.14)
2.4
(7.87)
8.7
(28.54)
4.4
(14.44)
2.9
(9.51)
12.9
(42.32)
6.1
(20.01)
3.9
(12.79)
13.9
(45.60)
7.6
(24.93)
4.9
(16.08)
5.9
(19.36)
3.1
(10.17)
2.0
(6.56)
LD = 2.9 m
(9.51 ft)
Z2
8.1
(26.57)
3.6
(11.81)
3.0
(9.84)
2.0
(6.56)
9.0
(29.53)
3.6
(11.81)
3.2
(10.50)
2.3
(7.55)
9.0
(29.53)
3.6
(11.81)
3.2
(10.50)
2.9
(9.51)
9.0
(29.53)
3.6
(11.81)
3.2
(10.50)
2.9
(9.51)
7.1
(23.29)
3.6
(11.81)
2.6
(8.53)
1.7
(5.58)
Z1
7.3
(23.95)
4.0
(13.12)
2.5
(8.20)
1.7
(5.58)
9.0
(29.53)
4.8
(15.75)
3.0
(9.84)
2.0
(6.56)
9.0
(29.53)
5.9
(19.36)
4.0
(13.12)
2.8
(9.19)
9.0
(29.53)
5.9
(19.36)
4.7
(15.42)
3.3
(10.83)
6.2
(20.34)
3.4
(11.15)
2.1
(6.89)
1.4
(4.59)
Z3
7.0
(22.97)
3.7
(12.14)
2.4
(7.87)
1.7
(5.58)
8.7
(28.54)
4.4
(14.44)
2.9
(9.51)
2.0
(6.56)
12.9
(42.32)
6.1
(20.01)
3.9
(12.79)
2.8
(9.19)
14.2
(46.59)
7.9
(25.92)
4.9
(16.08)
3.3
(10.83)
5.9
(19.36)
3.1
(10.17)
2.0
(6.56)
1.4
(4.59)

A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.3 m
(7.55 ft)
Z2
7.4
(24.28)
4.0
(13.12)
2.6
(8.53)
1.7
(5.58)
9.2
(30.18)
4.8
(15.75)
2.8
(9.19)
2.1
(6.89)
10.2
(33.46)
4.8
(15.75)
2.8
(9.19)
2.1
(6.89)
10.2
(33.46)
4.8
(15.75)
2.8
(9.19)
2.1
(6.89)
6.2
(20.34)
3.4
(11.15)
2.2
(7.22)
1.5
(4.92)
Z1
5.0
(16.40)
3.2
(10.50)
2.1
(6.89)
1.6
(5.25)
5.0
(16.40)
3.9
(12.79)
2.6
(8.53)
2.0
(6.56)
5.0
(16.40)
5.6
(18.37)
3.6
(11.81)
2.1
(6.89)
5.0
(16.40)
6.5
(21.32)
4.7
(15.42)
2.1
(6.89)
4.7
(15.42)
2.6
(8.53)
1.8
(5.90)
1.4
(4.59)
Z3
5.9
(19.36)
3.2
(10.50)
2.1
(6.89)
7.4
(24.28)
3.9
(12.79)
2.6
(8.53)
7.4
(24.28)
4.9
(16.08)
3.6
(11.81)
7.4
(24.28)
4.9
(16.08)
4.7
(15.42)
4.8
(15.75)
2.6
(8.53)
1.8
(5.90)
LD = 2.6 m
(8.53 ft)
Z2
7.7
(25.26)
4.1
(13.45)
2.6
(8.53)
1.8
(5.90)
9.2
(30.18)
4.9
(16.08)
3.1
(10.17)
1.9
(6.23)
9.2
(30.18)
5.1
(16.73)
3.1
(10.17)
1.9
(6.23)
9.2
(30.18)
5.1
(16.73)
3.1
(10.17)
1.9
(6.23)
6.5
(21.32)
3.5
(11.48)
2.2
(7.22)
1.5
(4.92)
Z1
5.8
(19.03)
3.1
(10.17)
2.1
(6.89)
1.6
(5.25)
5.8
(19.03)
3.9
(12.79)
2.6
(8.53)
1.9
(6.23)
5.8
(19.03)
5.5
(18.04)
3.6
(11.81)
2.7
(8.86)
5.8
(19.03)
6.1
(20.01)
4.6
(15.09)
2.9
(9.51)
4.6
(15.09)
2.6
(8.53)
1.7
(5.58)
1.3
(4.26)
Z3
5.8
(19.03)
3.1
(10.17)
2.1
(6.89)
7.5
(24.61)
3.9
(12.79)
2.6
(8.53)
8.4
(27.56)
5.5
(18.04)
3.6
(11.81)
8.4
(27.56)
5.7
(18.70)
4.6
(15.09)
4.7
(15.42)
2.6
(8.53)
1.7
(5.58)
LD = 2.9 m
(9.51 ft)
Z2
8.0
(26.25)
4.2
(13.78)
2.0
(6.56)
1.8
(5.90)
8.2
(26.31)
4.6
(15.09)
2.0
(6.56)
2.1
(6.89)
8.2
(26.31)
4.6
(15.09)
2.0
(6.56)
2.5
(8.20)
8.2
(26.90)
4.6
(15.09)
2.0
(6.56)
2.5
(8.20)
6.8
(22.31)
3.6
(11.81)
2.0
(6.56)
1.5
(4.92)
Z1
5.7
(18.70)
3.1
(10.17)
2.1
(6.89)
1.5
(4.92)
6.6
(21.65)
3.8
(12.47)
2.5
(8.20)
1.9
(6.23)
6.6
(21.65)
5.5
(18.04)
3.6
(11.81)
2.6
(8.53)
6.6
(21.65)
5.7
(18.70)
4.6
(15.09)
2.9
(9.51)
4.6
(15.09)
2.5
(8.20)
1.7
(5.58)
1.2
(3.94)
Z3
5.7
(18.70)
3.1
(10.17)
2.1
(6.89)
7.4
(24.28)
3.8
(12.47)
2.5
(8.20)
9.2
(30.18)
5.5
(18.04)
3.6
(11.81)
9.2
(30.18)
6.2
(20.34)
4.6
(15.09)
4.6
(15.09)
2.5
(8.20)
1.7
(5.58)

4.3 MH 5.6 MODELS
A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.0 m
(6.56 ft)
Z2
9.2
(30.18)
5.0
(16.40)
3.4
(11.15)
2.2
(7.22)
10.9
(35.76)
5.0
(16.40)
4.1
(13.45)
2.7
(8.86)
10.9
(35.76
5.0
(16.40)
5.2
(17.06)
3.5
(11.48)
10.9
(35.76)
5.0
(16.40)
5.3
(17.39)
4.0
(13.12)
8.0
(26.25)
4.5
(14.76)
3.0
(9.84)
1.9
(6.23)
Z1
8.4
(27.56)
4.5
(14.76)
2.8
(9.19)
2.0
(6.56)
10.8
(35.43)
5.6
(18.37)
3.5
(11.48)
2.5
(8.20)
11.1
(36.42)
7.6
(24.93)
4.6
(15.09)
3.4
(11.15)
11.1
(36.42)
8.1
(26.57)
5.8
(19.03)
4.1
(13.45)
7.1
(23.29)
3.9
(12.79)
2.4
(7.87)
1.7
(5.58)
Z3
8.0
(26.25)
4.3
(14.11)
2.7
(8.86)
10.5
(34.45)
5.4
(17.72)
3.4
(11.15)
14.0
(45.93)
7.3
(23.95)
4.6
(15.09)
14.0
(45.93)
9.3
(30.51)
5.4
(17.72)
6.7
(21.98)
3.7
(12.14)
2.3
(7.55)
LD = 2.4 m
(7.87 ft)
Z2
9.3
(30.51)
5.1
(16.73)
3.4
(11.15)
2.2
(7.22)
9.4
(30.84)
5.3
(17.39)
4.1
(13.45)
2.8
(9.19)
9.4
(30.84)
5.3
(17.39)
4.4
(14.44)
3.6
(11.81)
9.4
(30.84)
5.3
(17.39)
4.4
(14.44)
3.6
(11.81)
8.1
(26.57)
4.5
(14.76)
3.0
(9.84)
1.9
(6.23)
Z1
8.3
(27.23)
4.6
(15.09)
2.8
(9.19)
2.0
(6.56)
10.8
(35.43)
5.7
(18.70)
3.5
(11.48)
2.5
(8.20)
10.8
(35.43)
7.5
(24.61)
4.7
(15.42)
3.3
(10.83)
10.8
(35.43)
7.5
(24.61)
5.8
(19.03)
4.1
(13.45)
7.0
(22.97)
3.9
(12.79)
2.4
(7.87)
1.7
(5.58)
Z3
8.0
(26.25)
4.2
(13.78)
2.7
(8.86)
10.4
(34.12)
5.3
(17.39)
3.4
(11.15)
15.2
(49.87)
7.2
(23.62)
4.6
(15.09)
15.9
(52.16)
8.8
(28.87)
5.7
(18.70)
6.7
(21.98)
3.6
(11.81)
2.3
(7.55)
LD = 2.8 m
(9.17 ft)
Z2
6.4
(21.00)
3.4
(11.15)
3.4
(11.15)
2.2
(7.22)
6.4
(21.00)
3.4
(11.15)
4.1
(13.45)
2.7
(8.86)
6.4
(21.00)
3.4
(11.15)
4.3
(14.11)
2.7
(8.86)
6.4
(21.00)
3.4
(11.15)
4.3
(14.11)
2.7
(8.86)
6.4
(21.00)
3.4
(11.15)
3.0
(9.84)
2.0
(6.56)
Z1
8.3
(27.23)
4.6
(15.09)
2.8
(9.19)
1.9
(6.23)
10.6
(34.78)
5.7
(18.70)
3.6
(11.81)
2.4
(7.87)
10.6
(34.78
7.1
(23.29)
4.7
(15.42)
3.2
(10.50)
10.6
(34.78)
7.1
(23.29)
5.5
(18.04)
4.0
(13.12)
7.0
(22.97)
3.9
(12.79)
2.4
(7.87)
1.6
(5.25)
Z3
7.9
(25.92)
4.1
(13.45)
2.6
(8.53)
1.9
(6.23)
10.3
(33.79)
5.3
(17.39)
3.3
(10.83)
2.4
(7.87)
12.2
(40.03)
7.2
(23.62)
4.5
(14.76)
3.2
(10.50)
12.2
(40.03)
9.2
(30.18)
5.2
(17.06)
4.0
(13.12)
6.6
(21.55)
3.5
(11.48)
2.3
(7.55)
1.6
(5.25)

A (m) (ft)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
3.0
(9.84)
4.5
(14.76)
6.0
(19.68)
7.5
(24.61)
LD = 2.0 m
(6.56 ft)
Z2
9.1
(29.86)
4.6
(15.09)
3.0
(9.84)
2.1
(6.89)
11.3
(37.07)
5.7
(18.70)
3.7
(12.14)
2.6
(8.53)
11.3
(37.07)
6.6
(21.65)
4.9
(16.08)
3.5
(11.48)
11.3
(37.07)
6.6
(21.65)
5.3
(17.39)
4.2
(13.78)
7.8
(25.59)
4.0
(13.12)
2.6
(8.53)
1.9
(6.23)
Z1
7.3
(23.95)
3.9
(12.79)
2.7
(8.86)
2.0
(6.56)
9.1
(29.86)
5.0
(16.40)
3.4
(11.15)
2.5
(8.20)
9.1
(29.86)
6.9
(22.64)
4.5
(14.76)
3.3
(10.83)
9.1
(29.86)
8.7
(28.54)
5.6
(18.37)
4.1
(13.45)
6.1
(20.01)
3.3
(10.83)
2.3
(7.55)
1.7
(5.58)
Z3
7.4
(24.29)
3.9
(12.79)
2.7
(8.86)
9.7
(31.82)
5.0
(16.40)
3.4
(11.15)
10.4
(34.12)
5.5
(18.04)
4.5
(14.76)
10.4
(34.12)
5.5
(18.04)
5.6
(18.37)
6.2
(20.34)
3.4
(11.15)
2.3
(7.55)
LD = 2.4 m
(7.87 ft)
Z2
4.6
(15.09)
3.0
(9.84)
2.1
(6.89)
5.8
(19.03)
3.5
(11.48)
2.6
(8.53)
7.0
(22.97)
3.5
(11.48)
3.5
(11.48)
7.0
(22.97)
3.5
(11.48)
4.2
(13.78)
4.0
(13.12)
2.6
(8.53)
1.9
(6.23)
Z1
6.1
(20.01)
3.9
(12.79)
2.6
(8.53)
1.9
(6.23)
6.1
(20.01)
4.9
(16.08)
3.3
(10.83)
2.4
(7.87)
6.1
(20.01)
6.8
(22.31)
4.4
(14.44)
3.3
(10.83)
6.1
(20.01)
8.1
(26.57)
5.5
(18.04)
4.0
(13.12)
5.9
(19.36)
3.3
(10.83)
2.2
(7.22)
1.7
(5.58)
Z3
7.2
(23.62)
3.9
(12.79)
2.6
(8.53)
8.9
(29.20)
4.9
(16.08)
3.3
(10.83)
8.9
(29.20)
6.5
(21.32)
4.4
(14.44)
8.9
(29.20)
6.5
(21.32)
5.5
(18.04)
6.0
(19.65)
3.3
(10.83)
2.2
(7.22)
LD = 2.8 m
(9.17 ft)
Z2
8.8
(28.87)
4.7
(15.42)
3.1
(10.17)
2.1
(6.89)
11.2
(36.74)
5.8
(19.03)
3.8
(12.47)
2.6
(8.53)
11.8
(38.71)
6.4
(21.00)
4.0
(13.12)
3.5
(11.48)
11.8
(38.71)
6.4
(21.00)
4.0
(13.12)
3.6
(11.81)
7.5
(24.61)
4.1
(13.45)
2.7
(8.86)
1.8
(5.90)
Z1
5.4
(17.72)
3.8
(12.47)
2.5
(8.20)
1.9
(6.23)
5.4
(17.72)
4.9
(16.08)
3.2
(10.50)
2.4
(7.87)
5.4
(17.72)
6.7
(21.98)
4.4
(14.44)
3.2
(10.50)
5.4
(17.72)
7.5
(24.61)
5.5
(18.04)
4.0
(13.12)
5.4
(17.72)
3.2
(10.50)
2.2
(7.22)
1.6
(5.25)
Z3
7.0
(22.97)
3.8
(12.47)
2.5
(8.20)
1.9
(6.23)
9.4
(30.84)
4.6
(15.09)
3.2
(10.50)
2.4
(7.87)
10.2
(33.46)
4.6
(15.09)
4.4
(14.44)
3.2
(10.50)
10.2
(33.46)
4.6
(15.09)
4.9
(16.08)
4.0
(13.12)
5.9
(19.36)
3.2
(10.50)
2.2
(7.22)
1.6
(5.25)

NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual

NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual

Recommended

Recommended

More Related Content

Similar to NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual

Similar to NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual (20)

Recently uploaded

Recently uploaded (20)

NEW HOLLAND MH CITY WHEEL EXCAVATOR Service Repair Manual