2. Validity of this repair manual
This repair manual applies to the following tractors:
Description Type
Tractor serial number
From to
ARION 600 A77 A7700050 —
ARION 500 A75 A7500050 —
1/1Validité de ce manuel de réparation
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/2.1.2/191212/001/EN/T...
3. Complete engine
Technical specifications
Number Value Note – Description
For unspecified tightening torques, refer to the section entitled: "Tightening torques".
— 995 kg Complete 6-cylinder engine
— 730 kg Complete 4-cylinder engine
WARNING!
Lifting heavy components.
Risk of death or serious injury.
► Use certified slings or chains in perfect working order.
► Use a certified hoist in perfect working order.
► Use a certified jack or stand which can support the load.
► Use the jack or stand on a flat, horizontal, sufficiently firm surface.
► Place the jack or stand in a suitable location.
NOTICE!
Lubricants and fuels end up in the environment.
Environmental pollution
► Collect and store lubricants and fuels in suitable containers and dispose of them properly.
1/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
4. Special tool
Special tool – Reference no.
Carriage to be uncoupled
No. 00 1148 105 0
Special tool – Reference no.
Extension
No. 00 1148 106 0
Special tool – Reference no.
Set of two adjustable chains
No. 00 1146 172 0
2/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
5. Removal
► Before carrying out any removal operations, if the tractor is equipped with a suspended front axle, position
the front axle in the top position in manual mode. (7 Use → 7.3 Chassis).
► Fit 10-cm-high wooden chocks (1) between the end stops on the suspended front axle and the front chassis.
These operations make it easy to position the uncoupling trolleys afterwards.
► Disconnect the battery.
► Drain the engine as necessary.
► Drain the coolant circuit.
► Drain the air conditioning circuit.
► Drain the transmission.
► Decompress the front axle suspension circuit (if fitted).
Decompressing the front axle suspension circuit
► Drain the pneumatic braking circuit.
► Remove the engine bonnet.
Engine bonnet
► Remove the main tank.
Main tankFunction:01 Engine
► Remove the supports from the loader frame, if fitted.
► Remove the “SCR” and “CUC” catalytic converter unit with its support.
"SCR" and "CUC" catalytic converter unit (6 cylinders)
"SCR" and "CUC" catalytic converter unit (4 cylinders)
► Remove the exhaust filter.
Exhaust filter (6 cylinders)
3/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
6. Exhaust filter (4 cylinders)
On a 6-cylinder engine:
► Undo and remove the bolts (1) and the nut (2).
► Remove the protective panel (3).
► Undo and remove the nuts (1) from either side of the engine.
► Detach the wiring harness (2) from the engine bonnet support (3).
► Remove the engine bonnet support (3).
4/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
7. ► Remove the side members (1) either side of the engine, if fitted.
If equipped with a suspended front axle:
► Fit a suitable lifting tool (1) under the front axle suspension arm (2).
If equipped with a suspended front axle:
► Undo and remove the bolts (1).
► Use the lifting tool to fully lower the suspension arm (2).
5/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
8. On a 6-cylinder engine:
► Undo and remove the bolts (1) from the universal drive shaft.
If the bolts are not accessible, release the handbrake and the automatic parking brake (if fitted), lift one front
wheel only then rotate it until the universal drive shaft is in a suitable position.
► Disconnect the universal drive shaft (2).
► Undo and remove the bolts (3) from the engine/transmission coupling.
On a 4-cylinder engine:
► Undo and remove the bolts (1) from the universal drive shaft.
If the bolts are not accessible, release the handbrake and the automatic parking brake (if fitted), lift one front
wheel only then rotate it until the universal drive shaft is in a suitable position.
► Disconnect the universal drive shaft (2).
► Undo and remove the bolts (3) and remove the jaw.
► Undo and remove the bolts (4) from the engine/transmission coupling.
6/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
9. If equipped with a suspended front axle:
► Use the lifting tool to fit the suspension arm (1) in place.
► Fit and fully tighten the two bolts (2).
If equipped with a front linkage:
► Undo and remove the bolts (1) and (2).
► Remove the closure panels (3).
7/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
10. ► Loosen the clamps (1) and (2) and disconnect the hoses.
► Disconnect the unions (1).
► Disconnect the air conditioning ducts (2).
► Loosen the clamps (1) and disconnect the hoses.
► Disconnect the unions (2).
► Loosen the clamps (1) and disconnect the hoses.
8/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
11. ► Loosen the clamps (1) and disconnect the hoses.
If equipped with a front linkage:
► Using a suitable lifting tool, hold the cooler assembly at the lifting points (1).
If equipped with a front linkage:
► Undo and remove the bolts (1).
► Remove the cooler assembly (1).
9/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
12. The cooler assembly weighs 95 kg.
If equipped with a front linkage:
► Disconnect the connectors (1).
► Detach and remove the wiring harness (2) up to the front of the cab.
On the right-hand side of the tractor:
► Disconnect and detach the wiring harnesses (1).
On the left-hand side of the tractor:
10/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
13. ► Disconnect the connector (1).
► Detach and remove the wiring harness up to the front of the cab.
On the right-hand side of the tractor:
► Disconnect the unions (1).
► Remove the hydraulic pipes (2).
► Undo and remove the bolts (3).
On the right-hand side of the tractor (depending on the equipment):
► Disconnect the unions (1).
► Undo and remove the bolts (2).
11/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
14. On the left-hand side of the tractor:
► Disconnect the unions (1) and (2).
On the left-hand side of the tractor (depending on the equipment):
► Disconnect the unions (1) and (2).
► Remove the flanges (3).
► Undo and remove the bolts (4).
12/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
15. On the left-hand side of the tractor (depending on the equipment):
► Disconnect the unions (1) and (2).
► Undo and remove the bolts (3).
Under the cab:
If equipped with a suspended front axle:
► Disconnect the connector (1).
► Detach and remove the wiring harness up to the front chassis.
Under the cab:
► Undo and remove the nut (1).
► Disconnect the air conditioning ducts (2).
13/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
16. Under the cab:
► Remove the clamps (1) and disconnect the heating hoses.
► Position the tractor as horizontally as possible.
► Position the uncoupling trolleys (1) under the tractor.
14/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. ► Undo and remove the coupling bolts (1).
► Uncouple the engine from the transmission.
► Disconnect and detach the wiring harness (1).
► Loosen and remove the fan (2).
Note the direction of loosening of the nut. This nut has a left-handed thread.
If equipped with a front power take-off:
15/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
19. ► Undo and remove the bolts (1).
► Disconnect the front power take-off shaft (2).
► Remove the exhaust filter support (1).
► Fit the lifting kit on the engine (1).
► Secure the engine using suitable lifting equipment.
If equipped with a suspended front axle:
16/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN
20. ► Undo and remove the bolts (1).
► Loosen and remove the bolt (2).
► Remove the shaft (3).
If equipped with a suspended front axle:
► Lower the uncoupling trolley positioned under the suspension arm (1) of the front axle.
► Angle the bearing (2) as illustrated.
► Undo and remove the nuts (1).
17/33Moteur complet
2020/3/28http://localhost:8081/webtic/app/Module/1850/001/en/4.1.1/195330/003/EN