This document provides precautions for servicing the 2002 Nissan Maxima. It outlines safety precautions for working with the supplemental restraint system (SRS), Nissan Vehicle Immobilizer System (NVIS), and general vehicle repairs. Proper ventilation, protective equipment, and battery disconnection are recommended. Only specified fluids and tools should be used. Removed parts should be cleaned and replaced with new components as needed.

1. Edition: JULY 2001
Revision: AUGUST 2002
Publication No. SM2E-1A33U3
QUICK REFERENCE INDEX
All rights reserved. No part of this Service Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means,
electronic, mechanical, photo-copying, recording or otherwise, without the prior written permission of Nissan Motor Company Ltd., Tokyo, Japan.

2. FOREWORD
This manual contains maintenance and repair procedures for the
2002 Nissan MAXIMA.
In order to assure your safety and the efficient functioning of the
vehicle, this manual should be read thoroughly. It is especially
important that the PRECAUTIONS in the GI section be completely
understood before starting any repair task.
All information in this manual is based on the latest product infor-
mation at the time of publication. The right is reserved to make
changes in specifications and methods at any time without notice.
IMPORTANT SAFETY NOTICE
The proper performance of service is essential for both the safety of
the technician and the efficient functioning of the vehicle.
The service methods in this Service Manual are described in such a
manner that the service may be performed safely and accurately.
Service varies with the procedures used, the skills of the technician
and the tools and parts available. Accordingly, anyone using service
procedures, tools or parts which are not specifically recommended
by NISSAN must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the service
method selected.

3. Attachment No.20
TID CID
P0420 01H 01H Max. X -
P0420 02H 81H Min. X -
P0430 03H 02H Max. X -
P0430 04H 82H Min. X -
P0442 05H 03H Max. X -
P1442 05H 03H Max. X -
EVAP control system purge flow monitoring P0441 06H 83H Min. X mV
P0456 07H 03H Max. X -
P1456 07H 03H Max. X -
P0133 09H 04H Max. X ms
P1143 0AH 84H Min. X mV
P1144 0BH 04H Max. X mV
P0132 0CH 04H Max. X mV
P0134 0DH 04H Max. X s
P0153 11H 05H Max. X ms
P1163 12H 85H Min. X mV
P1164 13H 05H Max. X mV
P0152 14H 05H Max. X mV
P0154 15H 05H Max. X s
P0139 19H 86H Min. X mV/500ms
P1147 1AH 86H Min. X mV
P1146 1BH 06H Max. X mV
P0138 1CH 06H Max. X mV
P0159 21H 87H Min. X mV/500ms
P1167 22H 87H Min. X mV
P1166 23H 07H Max. X mV
P0158 24H 07H Max. X mV
P0032 29H 08H Max. X mV
P0031 2AH 88H Min. X mV
P0052 2BH 09H Max. X mV
P0051 2CH 89H Min. X mV
P0038 2DH 0AH Max. X mV
P0037 2EH 8AH Min. X mV
P0058 2FH 0BH Max. X mV
P0057 30H 8BH Min. X mV
TEST VALUE AND TEST LIMIT (GST ONLY — NOT APPLICABLE TO CONSULT-II)
The following is the information specified in Mode 6 of SAE J1979.
The test value is a parameter used to determine whether a system/circuit diagnostic test is “OK” or “NG” while
being monitored by the ECM during self-diagnosis. The test limit is a reference value which is specified as the
maximum or minimum value and is compared with the test value being monitored.
Items for which these data (test value and test limit) are displayed are the same as SRT code items.
These data (test value and test limit) are specified by Test ID (TID) and Component ID (CID) and can be dis-
played on the GST screen.
: Applicable ･: Not applicable
SRT item Self-diagnostic test item DTC
Test value
(GST display) Te s t limit Application Unit
CATALYST
Three way catalyst function (Bank 1)
Three way catalyst function (Bank 2)
EVAP SYSTEM
EVAP control system (Small leak)
EVAP control system (Very small leak)
HO2S
Heated oxygen sensor 1(Bank 1)
Heated oxygen sensor 1(Bank 2)
Heated oxygen sensor 2(Bank 1)
Heated oxygen sensor 2(Bank 2)
HO2S HTR
Heated oxygen sensor 1 heater(Bank 1)
Heated oxygen sensor 2 heater(Bank 2)
Heated oxygen sensor 2 heater(Bank 1)
Heated oxygen sensor 2 heater(Bank 2)

4. GENERAL INFORMATION
SECTION GI
CONTENTS
PRECAUTIONS ...............................................................3
Precautions..................................................................3
PRECAUTIONS FOR SUPPLEMENTAL
RESTRAINT SYSTEM (SRS) ″AIR BAG″ AND
″SEAT BELT PRE-TENSIONER″ .................................3
PRECAUTIONS FOR NVIS (NISSAN VEHICLE
IMMOBILIZER SYSTEM - NATS).................................3
GENERAL PRECAUTIONS.........................................4
PRECAUTIONS FOR MULTIPORT FUEL
INJECTION SYSTEM OR ENGINE CONTROL
SYSTEM ...................................................................6
PRECAUTIONS FOR THREE WAY CATALYST ...........6
PRECAUTIONS FOR HOSES.....................................6
PRECAUTIONS FOR ENGINE OILS ...........................7
PRECAUTIONS FOR FUEL........................................8
PRECAUTIONS FOR AIR CONDITIONING ..................8
HOW TO USE THIS MANUAL........................................9
HOW TO READ WIRING DIAGRAMS..........................11
Sample/Wiring Diagram - EXAMPL - ........................11
OPTIONAL SPLICE..................................................12
CONTROL UNIT TERMINALS AND REFERENCE
VALUE CHART........................................................13
Description.................................................................14
CONNECTOR SYMBOLS .........................................16
SWITCH POSITIONS ...............................................17
DETECTABLE LINES AND NON-DETECTABLE
LINES .....................................................................17
MULTIPLE SWITCH.................................................18
REFERENCE AREA.................................................19
HOW TO CHECK TERMINAL.......................................21
Connector and Terminal Pin Kit.................................21
How to Probe Connectors .........................................21
PROBING FROM HARNESS SIDE............................21
PROBING FROM TERMINAL SIDE ...........................21
How to Check Enlarged Contact Spring of
Terminal .....................................................................22
Waterproof Connector Inspection..............................23
RUBBER SEAL INSPECTION...................................23
WIRE SEAL INSPECTION........................................23
Terminal Lock Inspection...........................................23
HOW TO PERFORM EFFICIENT DIAGNOSIS
FOR AN ELECTRICAL INCIDENT ...............................24
Work Flow..................................................................24
Incident Simulation Tests...........................................25
INTRODUCTION......................................................25
VEHICLE VIBRATION ..............................................25
HEAT SENSITIVE....................................................26
FREEZING ..............................................................26
WATER INTRUSION ................................................27
ELECTRICAL LOAD.................................................27
COLD OR HOT START UP.......................................27
Circuit Inspection .......................................................27
INTRODUCTION......................................................27
TESTING FOR ″OPENS″ IN THE CIRCUIT ................28
TESTING FOR ″SHORTS″ IN THE CIRCUIT..............29
GROUND INSPECTION ...........................................30
VOLTAGE DROP TESTS..........................................30
CONTROL UNIT CIRCUIT TEST ...............................32
HOW TO FOLLOW TROUBLE DIAGNOSES...............34
How to Follow Test Groups in Trouble Diagnoses....35
Harness Wire Color and Connector Number
Indication....................................................................36
TYPE 1: HARNESS WIRE COLOR AND
CONNECTOR NUMBER ARE SHOWN IN
ILLUSTRATION .......................................................36
TYPE 2: HARNESS WIRE COLOR AND
CONNECTOR NUMBER ARE SHOWN IN TEXT ........36
Key to Symbols Signifying Measurements or
Procedures.................................................................37
CONSULT-II CHECKING SYSTEM...............................39
Function and System Application ..............................39
Nickel Metal Hydride Battery Replacement...............40
Checking Equipment..................................................40
CONSULT-II Data Link Connector (DLC) Circuit ......41
INSPECTION PROCEDURE .....................................41
IDENTIFICATION INFORMATION ................................42
Model Variation..........................................................42
PREFIX AND SUFFIX DESIGNATIONS .....................42
Identification Number.................................................43
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX

5. VEHICLE IDENTIFICATION NUMBER
ARRANGEMENT .....................................................43
IDENTIFICATION PLATE..........................................44
ENGINE SERIAL NUMBER.......................................44
AUTOMATIC TRANSAXLE NUMBER ........................44
MANUAL TRANSAXLE NUMBER..............................44
Dimensions ................................................................45
Wheels and Tires.......................................................45
LIFTING POINTS AND TOW TRUCK TOWING ...........46
Preparation ................................................................46
SPECIAL SERVICE TOOLS ......................................46
Boad-on Lift ...............................................................46
Garage Jack and Safety Stand .................................47
2-pole Lift...................................................................48
Tow Truck Towing ......................................................49
VEHICLE RECOVERY (FREEING A STUCK
VEHICLE)................................................................49
TIGHTENING TORQUE OF STANDARD BOLTS ........50
RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS ....................................................................51
SAE J1930 TERMINOLOGY LIST ................................52
SAE J1930 Terminology List .....................................52
CONTENTS (Cont’d)
GI-2

6. Precautions NFGI0001
Observe the following precautions to ensure safe and proper
servicing. These precautions are not described in each indi-
vidual section.
SGI646
PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT
SYSTEM (SRS) “AIR BAG” AND “SEAT BELT
PRE-TENSIONER” NFGI0001S01
The Supplemental Restraint System such as “AIR BAG” and “SEAT
BELT PRE-TENSIONER” used along with a seat belt, helps to
reduce the risk or severity of injury to the driver and front passen-
ger for certain types of collision. The SRS system composition
which is available to NISSAN MODEL A33 is as follows:
¼ For a frontal collision
The Supplemental Restraint System consists of driver air bag
module (located in the center of the steering wheel), front pas-
senger air bag module (located on the instrument panel on
passenger side), seat belt pre-tensioners, a diagnosis sensor
unit, crash zone sensor, warning lamp, wiring harness and
spiral cable.
¼ For a side collision
The Supplemental Restraint System consists of front side air
bag module (located in the outer side of front seat), satellite
sensor, diagnosis sensor unit (one of components of air bags
for a frontal collision), wiring harness, warning lamp (one of
components of air bags for a frontal collision).
Information necessary to service the system safely is included in
the RS section of this Service Manual.
WARNING:
¼ To avoid rendering the SRS inoperative, which could
increase the risk of personal injury or death in the event
of a collision which would result in air bag inflation, all
maintenance should be performed by an authorized
NISSAN dealer.
¼ Improper maintenance, including incorrect removal and
installation of the SRS, can lead to personal injury caused
by unintentional activation of the system. For removal of
Spiral Cable and Air Bag Module, see the RS section.
¼ Do not use electrical test equipment on any circuit related
to the SRS unless instructed to in this Service Manual.
SRS wiring harnesses can be identified by yellow harness
connector.
PRECAUTIONS FOR NVIS (NISSAN VEHICLE
IMMOBILIZER SYSTEM — NATS) NFGI0001S02
NVIS (NATS) will immobilize the engine if someone tries to start it
without the registered key of NVIS (NATS).
Both of the originally supplied ignition key IDs have been NVIS
(NATS) registered.
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PRECAUTIONS
Precautions
GI-3

7. The security indicator is located on the instrument panel. The indi-
cator blinks when the ignition switch is in “OFF” or “ACC” position.
Therefore, NVIS (NATS) warns outsiders that the vehicle is
equipped with the anti-theft system.
¼ When NVIS (NATS) detects malfunction, the security indicator
lamp lights up while ignition switch is in “ON” position.
This lighting up indicates that the anti-theft is not functioning,
so prompt service is required.
¼ When servicing NVIS (NATS) (trouble diagnoses, system ini-
tialization and additional registration of other NVIS (NATS) igni-
tion key IDs), CONSULT-II hardware and CONSULT-II NVIS
(NATS) software is necessary.
Regarding the procedures of NVIS (NATS) initialization and
NVIS (NATS) ignition key ID registration, refer to CONSULT-II
operation manual, NVIS (NATS).
Therefore, CONSULT-II NVIS (NATS) software (program card
and operation manual) must be kept strictly confidential to
maintain the integrity of the anti-theft function.
¼ When servicing NVIS (NATS) (trouble diagnoses, system ini-
tialization and additional registration of other NVIS (NATS) igni-
tion key IDs), it may be necessary to re-register original key
identification. Therefore, be sure to receive all keys from
vehicle owner. A maximum of five key IDs can be registered
into NVIS (NATS).
¼ When failing to start the engine first time using the key of NVIS
(NATS), start as follows.
a) Leave the ignition key in “ON” position for approximately 5
seconds.
b) Turn ignition key to “OFF” or “LOCK” position and wait approxi-
mately 5 seconds.
c) Repeat step 1 and 2 again.
d) Restart the engine while keeping the key separate from any
others on key-chain.
SGI285
GENERAL PRECAUTIONS NFGI0001S03
¼ Do not operate the engine for an extended period of time
without proper exhaust ventilation.
Keep the work area well ventilated and free of any inflammable
materials. Special care should be taken when handling any
inflammable or poisonous materials, such as gasoline, refrig-
erant gas, etc. When working in a pit or other enclosed area,
be sure to properly ventilate the area before working with haz-
ardous materials.
Do not smoke while working on the vehicle.
SGI231
¼ Before jacking up the vehicle, apply wheel chocks or other tire
blocks to the wheels to prevent the vehicle from moving. After
jacking up the vehicle, support the vehicle weight with safety
stands at the points designated for proper lifting before work-
ing on the vehicle.
These operations should be done on a level surface.
¼ When removing a heavy component such as the engine or
transaxle, be careful not to lose your balance and drop them.
Also, do not allow them to strike adjacent parts, especially the
brake tubes and master cylinder.
PRECAUTIONS
Precautions (Cont’d)
GI-4

8. SEF289H
¼ Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.
SGI233
¼ To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.
SGI234
¼ Before servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate cov-
ers.
Take caution that keys, buckles or buttons do not scratch paint.
¼ Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.
¼ Replace oil seals, gaskets, packings, O-rings, locking washers,
cotter pins, self-locking nuts, etc. with new ones.
¼ Replace inner and outer races of tapered roller bearings and
needle bearings as a set.
¼ Arrange the disassembled parts in accordance with their
assembled locations and sequence.
¼ Do not touch the terminals of electrical components which use
microcomputers (such as ECMs).
Static electricity may damage internal electronic components.
¼ After disconnecting vacuum or air hoses, attach a tag to indi-
cate the proper connection.
¼ Use only the fluids and lubricants specified in this manual.
¼ Use approved bonding agent, sealants or their equivalents
when required.
¼ Use tools and recommended special tools where specified for
safe and efficient service repairs.
¼ When repairing the fuel, oil, water, vacuum or exhaust
systems, check all affected lines for leaks.
¼ Dispose of drained oil or the solvent used for cleaning parts in
an appropriate manner.
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PRECAUTIONS
Precautions (Cont’d)
GI-5

9. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

10. Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically. Continued refueling may cause fuel
overflow, resulting in fuel spray and possibly a fire.
WARNING:
To prevent ECM from storing the diagnostic trouble codes, do
not carelessly disconnect the harness connectors which are
related to the engine control system and TCM (Transmission
Control Module) system. The connectors should be discon-
nected only when working according to the WORK FLOW of
TROUBLE DIAGNOSES in EC and AT sections.
SGI787
PRECAUTIONS FOR MULTIPORT FUEL INJECTION
SYSTEM OR ENGINE CONTROL SYSTEM NFGI0001S04
¼ Before connecting or disconnecting any harness connector for
the multiport fuel injection system or ECM:
Turn ignition switch to “OFF” position.
Disconnect negative battery terminal.
Otherwise, there may be damage to ECM.
¼ Before disconnecting pressurized fuel line from fuel pump to
injectors, be sure to release fuel pressure.
¼ Be careful not to jar components such as ECM and mass air
flow sensor.
PRECAUTIONS FOR THREE WAY CATALYST NFGI0001S05
If a large amount of unburned fuel flows into the catalyst, the cata-
lyst temperature will be excessively high. To prevent this, follow the
instructions below:
¼ Use unleaded gasoline only. Leaded gasoline will seriously
damage the three way catalyst.
¼ When checking for ignition spark or measuring engine
compression, make tests quickly and only when necessary.
¼ Do not run engine when the fuel tank level is low, otherwise the
engine may misfire, causing damage to the catalyst.
Do not place the vehicle on flammable material. Keep flammable
material off the exhaust pipe and the three way catalyst.
SMA019D
PRECAUTIONS FOR HOSES NFGI0001S06
Hose Removal and Installation NFGI0001S0601
¼ To prevent damage to rubber hose, do not pry off rubber hose
with tapered tool or screwdriver.
PRECAUTIONS
Precautions (Cont’d)
GI-6

11. SMA020D
¼ To reinstall the rubber hose securely, make sure of hose inser-
tion length and clamp orientation. (If tube is equipped with
hose stopper, insert rubber hose into tube until it butts up
against hose stopper.)
SMA021D
Hose Clamping NFGI0001S0602
¼ If old rubber hose is re-used, install hose clamp in its original
position (at the indentation where the old clamp was). If there
is a trace of tube bulging left on the old rubber hose, align
rubber hose at that position.
¼ Discard old clamps; replace with new ones.
SMA022D
¼ After installing leaf spring clamps, apply force to them in the
direction of the arrow, tightening rubber hose equally all
around.
PRECAUTIONS FOR ENGINE OILS NFGI0001S07
Prolonged and repeated contact with used engine oil may cause
skin cancer. Try to avoid direct skin contact with used oil.
If skin contact is made, wash thoroughly with soap or hand cleaner
as soon as possible.
Health Protection Precautions NFGI0001S0701
¼ Avoid prolonged and repeated contact with oils, particularly
used engine oils.
¼ Wear protective clothing, including impervious gloves where
practicable.
¼ Do not put oily rags in pockets.
¼ Avoid contaminating clothes, particularly underclothing, with
oil.
¼ Heavily soiled clothing and oil-impregnated footwear should
not be worn. Overalls must be cleaned regularly.
¼ First Aid treatment should be obtained immediately for open
cuts and wounds.
¼ Use barrier creams, applying them before each work period, to
help the removal of oil from the skin.
¼ Wash with soap and water to ensure all oil is removed (skin
cleansers and nail brushes will help). Preparations containing
lanolin replace the natural skin oils which have been removed.
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PRECAUTIONS
Precautions (Cont’d)
GI-7

12. ¼ Do not use gasoline, kerosine, diesel fuel, gas oil, thinners or
solvents for cleaning skin.
¼ If skin disorders develop, obtain medical advice without delay.
¼ Where practicable, degrease components prior to handling.
¼ Where there is a risk of eye contact, eye protection should be
worn, for example, chemical goggles or face shields; in addi-
tion an eye wash facility should be provided.
Environmental Protection Precautions NFGI0001S0702
Burning used engine oil in small space heaters or boilers can be
recommended only for units of approved design. The heating sys-
tem must meet the requirements of HM Inspectorate of Pollution for
small burners of less than 0.4 MW. If in doubt, check with the
appropriate local authority and/or manufacturer of the approved
appliance.
Dispose of used oil and used oil filters through authorized waste
disposal contractors to licensed waste disposal sites, or to the
waste oil reclamation trade. If in doubt, contact the local authority
for advice on disposal facilities.
It is illegal to pour used oil on to the ground, down sewers or drains,
or into water courses.
The regulations concerning the pollution vary between
regions.
PRECAUTIONS FOR FUEL NFGI0001S08
Use unleaded regular gasoline with an octane rating of at least 87
AKI (Anti-Knock Index) number (Research octane number 91).
For improved vehicle performance, NISSAN/INFINITI recommend
the use of unleaded premium gasoline with an octane rating of at
least 91 AKI number (Research octane number 96).
CAUTION:
Do not use leaded gasoline. Using leaded gasoline will dam-
age the three way catalyst.
Using a fuel other than that specified could adversely affect
the emission control devices and systems, and could also
affect the warranty coverage validity.
PRECAUTIONS FOR AIR CONDITIONING NFGI0001S09
Use an approved refrigerant recovery unit any time the air condi-
tioning system must be discharged. Refer to HA section (“HFC-
134a (R-134a) Service Procedure”, “SERVICE PROCEDURES”)
for specific instructions.
PRECAUTIONS
Precautions (Cont’d)
GI-8

13. NFGI0002
¼ The captions WARNING and CAUTION warn you of steps that must be followed to prevent personal injury
and/or damage to some part of the vehicle.
WARNING indicates the possibility of personal injury if instructions are not followed.
CAUTION indicates the possibility of component damage if instructions are not followed.
BOLD TYPED STATEMENTS except WARNING and CAUTION give you helpful information.
¼ ALPHABETICAL INDEX is provided at the end of this manual so that you can rapidly find the item and
page you are searching for.
¼ A QUICK REFERENCE INDEX, a black tab (e.g. ) is provided on the first page. You can quickly find
the first page of each section by matching it to the section’s black tab.
¼ THE CONTENTS are listed on the first page of each section.
¼ THE TITLE is indicated on the upper portion of each page and shows the part or system.
¼ THE PAGE NUMBER of each section consists of two letters which designate the particular section and a
number (e.g. “BR-5”).
¼ THE LARGE ILLUSTRATIONS are exploded views (See below.) and contain tightening torques, lubrica-
tion points, section number of the PARTS CATALOG (e.g. SEC. 440) and other information necessary to
perform repairs.
The illustrations should be used in reference to service matters only. When ordering parts, refer to the
appropriate PARTS CATALOG.
SBR364AC
¼ THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks
of work and hidden or tricky steps which are not shown in the previous large illustrations.
Assembly, inspection and adjustment procedures for the complicated units such as the automatic transaxle
or transmission, etc. are presented in a step-by-step format where necessary.
¼ The UNITS given in this manual are primarily expressed as the SI UNIT (International System of Unit),
and alternatively expressed in the metric system and in the yard/pound system.
“Example”
Tightening torque:
59 - 78 N·m (6.0 - 8.0 kg-m, 43 - 58 ft-lb)
¼ TROUBLE DIAGNOSES are included in sections dealing with complicated components.
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
HOW TO USE THIS MANUAL
GI-9

14. ¼ SERVICE DATA AND SPECIFICATIONS are contained at the end of each section for quick reference of
data.
¼ The following SYMBOLS AND ABBREVIATIONS are used:
SYMBOL ABBREVIATION SYMBOL ABBREVIATION
Tightening torque
2WD
2-Wheel Drive
Should be lubricated with grease. Unless oth-
erwise indicated, use recommended multi-pur-
pose grease.
A/C
Air Conditioner
Should be lubricated with oil. P/S Power Steering
Sealing point SST Special Service Tools
Checking point SAE Society of Automotive Engineers, Inc.
Always replace after every disassembly. ATF Automatic Transmission Fluid
kP
Apply petroleum jelly.
D1
Drive range 1st gear
Apply ATF. D2 Drive range 2nd gear
5 Select with proper thickness. D3 Drive range 3rd gear
6 Adjustment is required. D4 Drive range 4th gear
SDS Service Data and Specifications OD Overdrive
LH, RH Left-Hand, Right-Hand 22 2nd range 2nd gear
FR, RR Front, Rear 21 2nd range 1st gear
M/T Manual Transaxle/Transmission 12 1st range 2nd gear
A/T Automatic Transaxle/Transmission 11 1st range 1st gear
HOW TO USE THIS MANUAL
GI-10