SlideShare a Scribd company logo
1 of 29
Download to read offline
Service Repair Manual
Models
966C WHEEL LOADER
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Axles
SMCS - 3259-11; 3259-12
Remove Axles
1. Remove plug (3). Drain the oil from the final drive.
2. Remove bolts (1). Remove cover assembly (2) from the final drive planet carrier.
3. Pull axle (4) and gear part way out of the final drive.
NOTE: If the axle can not be removed, move the machine a small amount to the front or rear until
the axle can be pulled from the final drive.
1/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Fasten a hoist to the axle. Remove axle (4). The weight of the axle is 55 lb. (25 kg).
5. Remove retainer ring (6). Remove gear (5) and washer (7) from the axle.
Install Axles
1. Make sure the axles are clean and free of all dirt or foreign material.
2. Put washer (2) [with the steel side next to the gear] and gear (1) in position on the axle. Install
retainer ring (3).
3. Fasten a hoist to the axle. Put axle (4) in position in the final drive.
2/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Remove the retainer ring from the axle. Pull gear (1) part way off the axle. Put a piece of pipe
(5) which has a 2" (5.1 cm) outside diameter and is approximately 24 in. (61 cm) long in the gear
as shown. Push down on the pipe and slide the axle into position.
5. Remove the pipe. Slide gear (1) into position in the final drive planetary. Install the retainer ring
on the axle.
6. Turn the flat sides of the three shafts (7) as shown to give clearance for counterbore in cover.
7. Check the O-ring seal in the cover assembly for wear or damage. If necessary, make a
replacement.
NOTICE
If the cover does not fit flat up against the final drive without force,
remove the cover and do Step 6 again.
8. Install cover assembly (6) on the final drive planetary carrier.
9. Fill the final drive with oil to the correct level. See LUBRICATION AND MAINTENANCE
GUIDE.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:37:08 UTC+0800 2020
3/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Final Drive Planet Carriers
SMCS - 4092-11; 4092-12
Remove Final Drive Planet Carriers
start by:
a) remove axles
1. Remove two bolts (1) (180° apart). Install two 5/8"-11 NC guide bolts in their place.
2. Fasten tooling (A) and a hoist to the final drive planet carrier as shown. Remove the remainder
of the bolts that hold the final drive planet carrier to the wheel assembly.
1/2
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Install two 1/2"-13 NC forcing screws (2) and loosen the final drive planet carrier from the
wheel assembly.
4. Remove final drive planet carrier (3). The weight of the carrier is 100 lb. (45 kg).
Install Final Drive Planet Carrier
1. Check the O-ring on the back of the planet carrier for damage or wear. If necessary, make a
replacement.
2. Install two 5/8"-11 NC guide bolts (2) in the wheel assembly 180° apart as shown.
3. Fasten tooling (A) and a hoist to the planet carrier. Put final drive planet carrier (1) in position
in the wheel assembly. Install the bolts that hold it. Remove guide bolts (2). Install the remainder
of the bolts. Tighten the bolts to a torque of 150 ± 20 lb.ft. (205 ± 27 N·m).
end by:
a) install axles
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:38:03 UTC+0800 2020
2/2
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Final Drive Planet Carriers
SMCS - 4092-15; 4092-16
Disassemble Final Drive Planet Carriers
start by:
a) remove final drive planet carriers
1. Remove shafts (1) from the carrier.
2. Remove three gears (2) and twelve washers.
3. Remove retainer ring (4) from the shafts.
4. Remove two bearings (3) and spacer (5) from the gears.
Assemble Final Drive Planet Carriers
1/2
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
1. Install bearings (1) and (3) and spacers (2) in gears (4).
2. Install retainer rings (5) on the shaft.
3. Put gears and washers in position in the carrier with steel washers (7) next to the gears and
bronze washers (8) between the carrier and steel washers.
4. Install shafts (6) in the carrier.
end by:
a) install final drive planet carriers
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:38:59 UTC+0800 2020
2/2
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Final Drive Ring Gears And Hubs
SMCS - 4054; 4055-12; 4055-11
Remove Final Drive And Gears And Hubs
start by:
a) remove tires and rims (front or rear)
b) remove final drive planet carriers
1. Remove lockwire (2). Remove bolts (1) from nut (3).
1/5
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Fasten tool (A) and a hoist to the wheel assembly as shown. Put an up force on the wheel
assembly with the hoist.
3. Use tooling (B) to remove nut (3) from the spindle.
4. Use two persons to remove ring gear (4) and hub from the spindle. The weight of the ring gear
and hub is 80 lb. (36 kg).
5. Remove bolts (5). Remove locks (6) and plates and remove hub assembly (7) from the ring
gear.
6. Use tooling (C) to remove bearing cone (8) from the hub.
2/5
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Install Final Drive Ring Gears And Hubs
1. Heat the bearing cone to a maximum temperature of 275° (135°C). Install bearing cone (1) on
the hub.
2. Put hub assembly (2) in position in the ring gear.
3. Install plates (3), locks and bolts that hold the hub in the ring gear.
3/5
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Use two persons to put ring gear (4) and hub in position on the spindle.
5. Install nut (5) on the spindle. Remove tool (A) and the hoist from the wheel assembly.
6. Make an adjustment to the wheel bearings as follows:
a) Use an 8 in. (20.3 cm) long torque wrench (9S7354) on the wheel stud to slowly turn the wheel
assembly while nut (5) is tightened with tooling (B). Tighten nut (5) until it takes a torque of 160
± 50 lb.in. (18.1 ± 5.7 N·m) to turn the wheel assembly one complete revolution.
NOTE: Make sure the torque wrench is installed on the wheel stud so it is in line with the center
of the wheel as shown.
b) Loosen nut (5). Tighten nut (5) again until it takes a torque of 75 ± 25 lb.in. (8.5 ± 2.8 N·m) to
slowly turn the wheel assembly one complete revolution with an 8 in. (20.3 cm) torque wrench
(9S7354) at the wheel stud.
NOTE: For torque wrenches of different lengths use the following formula for the correct torque:
4/5
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
C is the torque wrench reading.
A is the length of the torque wrench.
B is the distance from the center of the axle housing to the wheel stud.
T is torque to turn the wheel assembly.
T=160 ± 50 lb.in. (18.1 ± 5.7 N·m) for Step (a) and 75 ± 25 lb.in. (8.5 ± 2.8 N·m) for Step (b).
7. Install bolts (7) in the hub assembly. If necessary, turn nut (5) in a clockwise direction until the
holes in the nut are in alignment with the holes in the hub assembly. Install lockwire (6) through
the bolts.
end by:
a) install final drive planet carriers
b) install tires and rims (front or rear)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:39:55 UTC+0800 2020
5/5
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Wheels, Bearings And Duo-Cone Seals
SMCS - 4208-11; 4208-12
Remove Wheels, Bearings And Duo-Cone Seals
start by:
a) remove final drive ring gears and hubs
1. Use tool (A) and a hoist to remove wheel assembly (1) from the spindle. The weight of the
wheel assembly is 330 lb. (149 kg).
2. Remove Duo-Cone seal (2) from the wheel assembly.
1/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Remove bolts (3) and locks. Use two persons to remove brake drum (4) from the wheel
assembly. The weight of the brake drum is 100 lb. (45 kg).
4. Remove bearing cups (5) from the wheel assembly.
5. Remove bearing cone (7) from the spindle.
6. Remove Duo-Cone seal (6) from the retainer.
7. If necessary, remove locks, bolts and bars (8). Remove retainer (9) from the spindle. Remove
the O-ring seal from the back of the retainer.
Install Wheels, Bearings And Duo-Cone Seals
1. If retainer was removed, install O-ring seal on the back of the retainer. Put retainer in position
on the spindle and install the bars, locks and bolts that hold it.
2/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Make sure the rubber torus seals are clean and dry. Make sure all metal surfaces that make
contact with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in
the retainer. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that make
contact with each other.
3. Install bearing cone (1) on the spindle.
4. Lower the temperature of the bearing cups. Install bearing cups (2) in the wheel assembly.
5. Use two persons to install brake drum (4) on the wheel assembly. Install locks and bolts (3).
3/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Make sure rubber torus seals are clean and dry. Make sure all metal surfaces that make contact
with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in the
wheel assembly. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that
make contact with each other.
7. Fasten tool (B) and a hoist to the wheel assembly. Put wheel assembly (5) in position on the
spindle.
end by:
a) install final drive ring gears and hubs
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:40:51 UTC+0800 2020
4/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Brake Shoes
SMCS - 4253-12; 4253-11
Remove Brake Shoes
start by:
a) remove wheels, bearings and Duo-Cone seals
1. Remove covers (1) from the spindle.
2. Use an acceptable brake tool to remove springs (2) from the brake shoes.
1/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Remove lockwire (5). Loosen bolts (3) approximately .50 in. (12.7 mm).
4. Remove springs (4) from the pins.
5. Remove retainers (7) and felt washers.
6. Remove pins (6). Remove brake shoes (8). Remove springs, retainers and felt washers from the
other end of pins (6).
Install Brake Shoes
1. Install the felt washers, retainers and springs on one end of pins (2).
2. Put brake shoes (3) in position on the spider and bearing assembly and install pins (2).
3. Install felt washers and retainers (1) on the pins.
2/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Install springs (5) on the pins.
5. Tighten bolts (4). Make sure the holes in the pins are in alignment with the bolts before the
bolts are tightened.
6. Use an acceptable brake tool (6) to install springs (7) on the brake shoes.
7. Install covers (8) on the spindle.
NOTE: After the final drive ring gears and hubs have been installed, make an adjustment to the
brakes. See BRAKE ADJUSTMENT, 966C AIR SYSTEM AND BRAKES.
end by:
a) install wheels, bearings and Duo-Cone seals
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:41:46 UTC+0800 2020
3/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Wheel Spindles
SMCS - 4205-12; 4205-11
Remove Wheel Spindles
start by:
a) remove brake shoes
1. Turn slack adjuster (3) to release any force on pin (1).
2. Remove retainer ring (2) from the brake camshaft.
3. Remove brake camshaft (5). Remove washers (4) from between the bracket assembly and slack
adjuster assembly and from between the brake camshaft and spindle housing.
1/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Make sure the air pressure in the brake system is zero before any lines
are disconnected.
4. Disconnect air lines (6) from the chamber assembly.
5. Remove bolts (9). Remove bracket assembly (8), slack adjuster assembly and chamber
assembly from the spindle assembly as a unit.
6. Fasten a hoist to the wheel spindle assembly. Remove nuts (7) and washers. Remove wheel
spindle assembly (10). The weight of the wheel spindle assembly is 100 lb. (45 kg).
7. Remove O-ring seal (13) from the spindle.
2/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Use four 1/2"-13 NC forcing screws to remove spider and bearing assembly (12) from spindle
(11).
9. Remove sleeve (14), lip seal and bearing from the spider.
Install Wheel Spindles
1. Use tooling (A) to install sleeve (3) in the spider. Use tooling (A) to install bearing and lip seal
in the opposite side of the spider. Install the seal with the lip toward the bearing.
2. Install spindle (4) in spider and bearing assembly (2). Put 1P808 General Purpose Lubricant in
the bearing and bore of the spider assembly.
3. Install O-ring seal (1) on the spindle.
4. Fasten a hoist to the wheel spindle assembly. Install wheel spindle assembly (5) on the axle
housing. Install the washers and nuts that hold it. Tighten the nuts to a torque of 345 ± 30 lb.ft.
(465 ± 40 N·m).
3/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Install bracket assembly (7), slack adjuster assembly and chamber assembly on the spindle
assembly as a unit.
6. Connect air lines (6) to the chamber assembly.
7. Install washer (8) on the brake camshaft. Install brake camshaft (9) in spider and bracket
assemblies. Install washer and slack adjuster assembly (10) on brake camshaft (9). Install the
retainer ring on the brake camshaft.
end by:
a) install brake shoes
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:42:42 UTC+0800 2020
4/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Front Differential And Carrier
SMCS - 3258-12; 3258-11
Remove Front Differential And Carrier
start by:
a) remove axles (front only)
1. Remove plug (1). Drain the oil from the front axle housing.
2. Remove spider and bearing assembly (4) from the front drive shaft (3) and differential pinion
shaft.
1/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Remove yoke (2) from the differential pinion shaft.
Make sure the air pressure in the brake system is zero before any lines
are disconnected.
4. Disconnect three lines (5) from the tee fitting.
5. Disconnect three lines (6) from the quick release valve.
6. Disconnect clips (7) from each side of the axle housing and pull the air lines clear of the
differential and carrier.
7. Fasten tooling (A) to the front differential and carrier as shown. Remove bolts (9). Install two
1/2"-13 NC forcing screws and remove differential and carrier (8) from the axle housing. The
weight of the differential and carrier is 350 lb. (158 kg).
Install Front Differential And Carrier
2/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
1. Fasten tooling (A) to the differential and carrier as shown. Put differential and carrier (1) in
position in the axle housing. Install the bolts that hold it. Tighten the bolts to a torque of 195 ± 18
lb.ft. (265 ± 24 N·m).
2. Connect three air lines (2) to the tee fitting.
3. Connect three air lines (3) to the quick release valve.
4. Connect the clips that hold the air lines in position on the axle housing.
5. Install yoke (4) on the differential pinion shaft.
3/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Install spider and bearing assembly (5) on the yoke and front drive shaft. Tighten the bolts to a
torque of 100 ± 10 lb.ft. (135 ± 14 N·m).
7. Install the drain plug and fill the front axle housing with oil to the correct level. See
LUBRICATION AND MAINTENANCE GUIDE.
end by:
a) install axles (front only)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:43:38 UTC+0800 2020
4/4
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

Similar to Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)

Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
fjjskmdmem
 
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
km7seyrduhdw
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
fjjskmdmem
 
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
fjjskmdmem
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
udfjjsjekdkdmm
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
fujsjefksekmm
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
fhsejkdkmem
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
fjjskekdmem
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
fujseskemmesd
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
fiskefjskemem
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
fusjefjkksemmd
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
jjskekfsme
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
kfs9eidokd
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
fjjskmdmem
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
fjsjjekdkme
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
fjskksmem
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
idksmmdmdm
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
jkdkkdsmmd
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
fujskkmdmdm
 

Similar to Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655) (20)

Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
 
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...
 
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
Caterpillar Cat 966C WHEEL LOADER (Prefix 76J) Service Repair Manual (76J0965...
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...
 
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
 
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
Caterpillar cat 140 g motor grader (prefix 81v) service repair manual (81v010...
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
 
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...
 
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
Caterpillar cat 135 h na motor grader (prefix 3yk) service repair manual (3yk...
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual Instant ...
 
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
Caterpillar Cat 120H Motor Grader (Prefix 2AN) Service Repair Manual (2AN0000...
 

More from fjsjjekdkme

Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manualKobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
fjsjjekdkme
 
Kobelco sk380 xdlc 10 hydraulic excavator service repair manual
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualKobelco sk380 xdlc 10 hydraulic excavator service repair manual
Kobelco sk380 xdlc 10 hydraulic excavator service repair manual
fjsjjekdkme
 
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualKobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
fjsjjekdkme
 
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
fjsjjekdkme
 
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
fjsjjekdkme
 
Kawasaki 135 zv 2 wheel loader operation and maintenance manual
Kawasaki 135 zv 2 wheel loader operation and maintenance manualKawasaki 135 zv 2 wheel loader operation and maintenance manual
Kawasaki 135 zv 2 wheel loader operation and maintenance manual
fjsjjekdkme
 
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
fjsjjekdkme
 
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
fjsjjekdkme
 
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
fjsjjekdkme
 
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
fjsjjekdkme
 
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
fjsjjekdkme
 
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
fjsjjekdkme
 

More from fjsjjekdkme (20)

Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manualKobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
Kobelco sk500 lc 10 (eu 2019) hydraulic excavator service repair manual
 
Kobelco sk380 xdlc 10 hydraulic excavator service repair manual
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualKobelco sk380 xdlc 10 hydraulic excavator service repair manual
Kobelco sk380 xdlc 10 hydraulic excavator service repair manual
 
Kobelco sk300 lc 10 hydraulic excavator service repair manual
Kobelco sk300 lc 10 hydraulic excavator service repair manualKobelco sk300 lc 10 hydraulic excavator service repair manual
Kobelco sk300 lc 10 hydraulic excavator service repair manual
 
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualKobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manual
 
Kobelco sk260 lc 10 hydraulic excavator service repair manual
Kobelco sk260 lc 10 hydraulic excavator service repair manualKobelco sk260 lc 10 hydraulic excavator service repair manual
Kobelco sk260 lc 10 hydraulic excavator service repair manual
 
Kobelco sk250 10 hydraulic excavator service repair manual
Kobelco sk250 10 hydraulic excavator service repair manualKobelco sk250 10 hydraulic excavator service repair manual
Kobelco sk250 10 hydraulic excavator service repair manual
 
Kobelco sk60 8 hydraulic excavator service repair manual
Kobelco sk60 8 hydraulic excavator service repair manualKobelco sk60 8 hydraulic excavator service repair manual
Kobelco sk60 8 hydraulic excavator service repair manual
 
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-9301 an...
 
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
Kawasaki 135 zv 2 wheel loader service repair manual (serial no. 13c1-5301 an...
 
Kawasaki 135 zv 2 wheel loader operation and maintenance manual
Kawasaki 135 zv 2 wheel loader operation and maintenance manualKawasaki 135 zv 2 wheel loader operation and maintenance manual
Kawasaki 135 zv 2 wheel loader operation and maintenance manual
 
Kawasaki 92 z7 wheel loader service repair manual
Kawasaki 92 z7 wheel loader service repair manualKawasaki 92 z7 wheel loader service repair manual
Kawasaki 92 z7 wheel loader service repair manual
 
Kawasaki 92 z7 wheel loader operation and maintenance manual
Kawasaki 92 z7 wheel loader operation and maintenance manualKawasaki 92 z7 wheel loader operation and maintenance manual
Kawasaki 92 z7 wheel loader operation and maintenance manual
 
Kawasaki 90 z7 wheel loader service repair manual
Kawasaki 90 z7 wheel loader service repair manualKawasaki 90 z7 wheel loader service repair manual
Kawasaki 90 z7 wheel loader service repair manual
 
Kawasaki 90 z7 wheel loader operation and maintenance manual
Kawasaki 90 z7 wheel loader operation and maintenance manualKawasaki 90 z7 wheel loader operation and maintenance manual
Kawasaki 90 z7 wheel loader operation and maintenance manual
 
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)
 
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)
 
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)
 
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
Kawasaki 85 z7b wheel loader equipment components parts catalogue manual (ser...
 
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)
 
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)
 

Recently uploaded

快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
kthcah
 
一比一原版英国哈珀亚当斯大学毕业证如何办理
一比一原版英国哈珀亚当斯大学毕业证如何办理一比一原版英国哈珀亚当斯大学毕业证如何办理
一比一原版英国哈珀亚当斯大学毕业证如何办理
AS
 
出售伯明翰大学毕业证研究生文凭证书原版质量
出售伯明翰大学毕业证研究生文凭证书原版质量出售伯明翰大学毕业证研究生文凭证书原版质量
出售伯明翰大学毕业证研究生文凭证书原版质量
kthcah
 
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
eehzz
 
mechanical vibrations pebbles.pptbbbbbbbbx
mechanical vibrations pebbles.pptbbbbbbbbxmechanical vibrations pebbles.pptbbbbbbbbx
mechanical vibrations pebbles.pptbbbbbbbbx
joshuaclack73
 
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
zovambe
 
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
AD
 
John Deere 990 Compact Utility Tractor Shop Manual.pdf
John Deere 990 Compact Utility Tractor Shop Manual.pdfJohn Deere 990 Compact Utility Tractor Shop Manual.pdf
John Deere 990 Compact Utility Tractor Shop Manual.pdf
Excavator
 

Recently uploaded (20)

EV Charging Resources and Technical Assistance for Rural Communities and Trib...
EV Charging Resources and Technical Assistance for Rural Communities and Trib...EV Charging Resources and Technical Assistance for Rural Communities and Trib...
EV Charging Resources and Technical Assistance for Rural Communities and Trib...
 
What Could Cause Your Audi To Keep Cutting Out
What Could Cause Your Audi To Keep Cutting OutWhat Could Cause Your Audi To Keep Cutting Out
What Could Cause Your Audi To Keep Cutting Out
 
快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
快速办理澳洲昆士兰科技大学毕业证教育部学历认证书一模一样
 
一比一原版英国哈珀亚当斯大学毕业证如何办理
一比一原版英国哈珀亚当斯大学毕业证如何办理一比一原版英国哈珀亚当斯大学毕业证如何办理
一比一原版英国哈珀亚当斯大学毕业证如何办理
 
Microscope of ppt for botany major this is a project
Microscope of ppt for botany major this is a projectMicroscope of ppt for botany major this is a project
Microscope of ppt for botany major this is a project
 
出售伯明翰大学毕业证研究生文凭证书原版质量
出售伯明翰大学毕业证研究生文凭证书原版质量出售伯明翰大学毕业证研究生文凭证书原版质量
出售伯明翰大学毕业证研究生文凭证书原版质量
 
Things that make the new Nissan Z unique
Things that make the new Nissan Z uniqueThings that make the new Nissan Z unique
Things that make the new Nissan Z unique
 
How Do I Know If My Volvo Has Throttle Position Sensor Problems
How Do I Know If My Volvo Has Throttle Position Sensor ProblemsHow Do I Know If My Volvo Has Throttle Position Sensor Problems
How Do I Know If My Volvo Has Throttle Position Sensor Problems
 
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
原版定做(ncl学位证书)英国纽卡斯尔大学毕业证文凭学历证书-国外学历学位认证
 
mechanical vibrations pebbles.pptbbbbbbbbx
mechanical vibrations pebbles.pptbbbbbbbbxmechanical vibrations pebbles.pptbbbbbbbbx
mechanical vibrations pebbles.pptbbbbbbbbx
 
Auto Glass Repair in Redwood City What to Do When Disaster Strikes.pdf
Auto Glass Repair in Redwood City What to Do When Disaster Strikes.pdfAuto Glass Repair in Redwood City What to Do When Disaster Strikes.pdf
Auto Glass Repair in Redwood City What to Do When Disaster Strikes.pdf
 
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
一比一原版(CCA毕业证书)加利福尼亚艺术学院毕业证成绩单原件一模一样
 
Toyota Yaris service manual Free.pdf Toyota Yaris Service manual
Toyota Yaris service manual Free.pdf  Toyota Yaris Service manualToyota Yaris service manual Free.pdf  Toyota Yaris Service manual
Toyota Yaris service manual Free.pdf Toyota Yaris Service manual
 
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
一比一原版(Cumbria毕业证书)英国坎布里亚大学毕业证成绩单学位证书
 
Benefits of Load Planning in Fleet Management
Benefits of Load Planning in Fleet ManagementBenefits of Load Planning in Fleet Management
Benefits of Load Planning in Fleet Management
 
Why Won't My Mercedes Key Fob Function After A Battery Swap
Why Won't My Mercedes Key Fob Function After A Battery SwapWhy Won't My Mercedes Key Fob Function After A Battery Swap
Why Won't My Mercedes Key Fob Function After A Battery Swap
 
John Deere 990 Compact Utility Tractor Shop Manual.pdf
John Deere 990 Compact Utility Tractor Shop Manual.pdfJohn Deere 990 Compact Utility Tractor Shop Manual.pdf
John Deere 990 Compact Utility Tractor Shop Manual.pdf
 
AI for Smart Vehicles - A quick overview
AI for Smart Vehicles - A quick overviewAI for Smart Vehicles - A quick overview
AI for Smart Vehicles - A quick overview
 
Preparing for Transportation Electrification: The Electric Coop Perspective
Preparing for Transportation Electrification: The Electric Coop PerspectivePreparing for Transportation Electrification: The Electric Coop Perspective
Preparing for Transportation Electrification: The Electric Coop Perspective
 
Charging Forward: Bringing Electric Vehicle Charging Infrastructure to Rural ...
Charging Forward: Bringing Electric Vehicle Charging Infrastructure to Rural ...Charging Forward: Bringing Electric Vehicle Charging Infrastructure to Rural ...
Charging Forward: Bringing Electric Vehicle Charging Infrastructure to Rural ...
 

Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)

  • 2. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Axles SMCS - 3259-11; 3259-12 Remove Axles 1. Remove plug (3). Drain the oil from the final drive. 2. Remove bolts (1). Remove cover assembly (2) from the final drive planet carrier. 3. Pull axle (4) and gear part way out of the final drive. NOTE: If the axle can not be removed, move the machine a small amount to the front or rear until the axle can be pulled from the final drive. 1/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. 4. Fasten a hoist to the axle. Remove axle (4). The weight of the axle is 55 lb. (25 kg). 5. Remove retainer ring (6). Remove gear (5) and washer (7) from the axle. Install Axles 1. Make sure the axles are clean and free of all dirt or foreign material. 2. Put washer (2) [with the steel side next to the gear] and gear (1) in position on the axle. Install retainer ring (3). 3. Fasten a hoist to the axle. Put axle (4) in position in the final drive. 2/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. 4. Remove the retainer ring from the axle. Pull gear (1) part way off the axle. Put a piece of pipe (5) which has a 2" (5.1 cm) outside diameter and is approximately 24 in. (61 cm) long in the gear as shown. Push down on the pipe and slide the axle into position. 5. Remove the pipe. Slide gear (1) into position in the final drive planetary. Install the retainer ring on the axle. 6. Turn the flat sides of the three shafts (7) as shown to give clearance for counterbore in cover. 7. Check the O-ring seal in the cover assembly for wear or damage. If necessary, make a replacement. NOTICE If the cover does not fit flat up against the final drive without force, remove the cover and do Step 6 again. 8. Install cover assembly (6) on the final drive planetary carrier. 9. Fill the final drive with oil to the correct level. See LUBRICATION AND MAINTENANCE GUIDE. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:37:08 UTC+0800 2020 3/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Final Drive Planet Carriers SMCS - 4092-11; 4092-12 Remove Final Drive Planet Carriers start by: a) remove axles 1. Remove two bolts (1) (180° apart). Install two 5/8"-11 NC guide bolts in their place. 2. Fasten tooling (A) and a hoist to the final drive planet carrier as shown. Remove the remainder of the bolts that hold the final drive planet carrier to the wheel assembly. 1/2 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. 3. Install two 1/2"-13 NC forcing screws (2) and loosen the final drive planet carrier from the wheel assembly. 4. Remove final drive planet carrier (3). The weight of the carrier is 100 lb. (45 kg). Install Final Drive Planet Carrier 1. Check the O-ring on the back of the planet carrier for damage or wear. If necessary, make a replacement. 2. Install two 5/8"-11 NC guide bolts (2) in the wheel assembly 180° apart as shown. 3. Fasten tooling (A) and a hoist to the planet carrier. Put final drive planet carrier (1) in position in the wheel assembly. Install the bolts that hold it. Remove guide bolts (2). Install the remainder of the bolts. Tighten the bolts to a torque of 150 ± 20 lb.ft. (205 ± 27 N·m). end by: a) install axles Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:38:03 UTC+0800 2020 2/2 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Final Drive Planet Carriers SMCS - 4092-15; 4092-16 Disassemble Final Drive Planet Carriers start by: a) remove final drive planet carriers 1. Remove shafts (1) from the carrier. 2. Remove three gears (2) and twelve washers. 3. Remove retainer ring (4) from the shafts. 4. Remove two bearings (3) and spacer (5) from the gears. Assemble Final Drive Planet Carriers 1/2 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. 1. Install bearings (1) and (3) and spacers (2) in gears (4). 2. Install retainer rings (5) on the shaft. 3. Put gears and washers in position in the carrier with steel washers (7) next to the gears and bronze washers (8) between the carrier and steel washers. 4. Install shafts (6) in the carrier. end by: a) install final drive planet carriers Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:38:59 UTC+0800 2020 2/2 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Final Drive Ring Gears And Hubs SMCS - 4054; 4055-12; 4055-11 Remove Final Drive And Gears And Hubs start by: a) remove tires and rims (front or rear) b) remove final drive planet carriers 1. Remove lockwire (2). Remove bolts (1) from nut (3). 1/5 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. 2. Fasten tool (A) and a hoist to the wheel assembly as shown. Put an up force on the wheel assembly with the hoist. 3. Use tooling (B) to remove nut (3) from the spindle. 4. Use two persons to remove ring gear (4) and hub from the spindle. The weight of the ring gear and hub is 80 lb. (36 kg). 5. Remove bolts (5). Remove locks (6) and plates and remove hub assembly (7) from the ring gear. 6. Use tooling (C) to remove bearing cone (8) from the hub. 2/5 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. Install Final Drive Ring Gears And Hubs 1. Heat the bearing cone to a maximum temperature of 275° (135°C). Install bearing cone (1) on the hub. 2. Put hub assembly (2) in position in the ring gear. 3. Install plates (3), locks and bolts that hold the hub in the ring gear. 3/5 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. 4. Use two persons to put ring gear (4) and hub in position on the spindle. 5. Install nut (5) on the spindle. Remove tool (A) and the hoist from the wheel assembly. 6. Make an adjustment to the wheel bearings as follows: a) Use an 8 in. (20.3 cm) long torque wrench (9S7354) on the wheel stud to slowly turn the wheel assembly while nut (5) is tightened with tooling (B). Tighten nut (5) until it takes a torque of 160 ± 50 lb.in. (18.1 ± 5.7 N·m) to turn the wheel assembly one complete revolution. NOTE: Make sure the torque wrench is installed on the wheel stud so it is in line with the center of the wheel as shown. b) Loosen nut (5). Tighten nut (5) again until it takes a torque of 75 ± 25 lb.in. (8.5 ± 2.8 N·m) to slowly turn the wheel assembly one complete revolution with an 8 in. (20.3 cm) torque wrench (9S7354) at the wheel stud. NOTE: For torque wrenches of different lengths use the following formula for the correct torque: 4/5 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. C is the torque wrench reading. A is the length of the torque wrench. B is the distance from the center of the axle housing to the wheel stud. T is torque to turn the wheel assembly. T=160 ± 50 lb.in. (18.1 ± 5.7 N·m) for Step (a) and 75 ± 25 lb.in. (8.5 ± 2.8 N·m) for Step (b). 7. Install bolts (7) in the hub assembly. If necessary, turn nut (5) in a clockwise direction until the holes in the nut are in alignment with the holes in the hub assembly. Install lockwire (6) through the bolts. end by: a) install final drive planet carriers b) install tires and rims (front or rear) Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:39:55 UTC+0800 2020 5/5 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Wheels, Bearings And Duo-Cone Seals SMCS - 4208-11; 4208-12 Remove Wheels, Bearings And Duo-Cone Seals start by: a) remove final drive ring gears and hubs 1. Use tool (A) and a hoist to remove wheel assembly (1) from the spindle. The weight of the wheel assembly is 330 lb. (149 kg). 2. Remove Duo-Cone seal (2) from the wheel assembly. 1/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. 3. Remove bolts (3) and locks. Use two persons to remove brake drum (4) from the wheel assembly. The weight of the brake drum is 100 lb. (45 kg). 4. Remove bearing cups (5) from the wheel assembly. 5. Remove bearing cone (7) from the spindle. 6. Remove Duo-Cone seal (6) from the retainer. 7. If necessary, remove locks, bolts and bars (8). Remove retainer (9) from the spindle. Remove the O-ring seal from the back of the retainer. Install Wheels, Bearings And Duo-Cone Seals 1. If retainer was removed, install O-ring seal on the back of the retainer. Put retainer in position on the spindle and install the bars, locks and bolts that hold it. 2/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. 2. Make sure the rubber torus seals are clean and dry. Make sure all metal surfaces that make contact with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in the retainer. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that make contact with each other. 3. Install bearing cone (1) on the spindle. 4. Lower the temperature of the bearing cups. Install bearing cups (2) in the wheel assembly. 5. Use two persons to install brake drum (4) on the wheel assembly. Install locks and bolts (3). 3/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. 6. Make sure rubber torus seals are clean and dry. Make sure all metal surfaces that make contact with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in the wheel assembly. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that make contact with each other. 7. Fasten tool (B) and a hoist to the wheel assembly. Put wheel assembly (5) in position on the spindle. end by: a) install final drive ring gears and hubs Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:40:51 UTC+0800 2020 4/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Brake Shoes SMCS - 4253-12; 4253-11 Remove Brake Shoes start by: a) remove wheels, bearings and Duo-Cone seals 1. Remove covers (1) from the spindle. 2. Use an acceptable brake tool to remove springs (2) from the brake shoes. 1/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 19. 3. Remove lockwire (5). Loosen bolts (3) approximately .50 in. (12.7 mm). 4. Remove springs (4) from the pins. 5. Remove retainers (7) and felt washers. 6. Remove pins (6). Remove brake shoes (8). Remove springs, retainers and felt washers from the other end of pins (6). Install Brake Shoes 1. Install the felt washers, retainers and springs on one end of pins (2). 2. Put brake shoes (3) in position on the spider and bearing assembly and install pins (2). 3. Install felt washers and retainers (1) on the pins. 2/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 20. 4. Install springs (5) on the pins. 5. Tighten bolts (4). Make sure the holes in the pins are in alignment with the bolts before the bolts are tightened. 6. Use an acceptable brake tool (6) to install springs (7) on the brake shoes. 7. Install covers (8) on the spindle. NOTE: After the final drive ring gears and hubs have been installed, make an adjustment to the brakes. See BRAKE ADJUSTMENT, 966C AIR SYSTEM AND BRAKES. end by: a) install wheels, bearings and Duo-Cone seals Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:41:46 UTC+0800 2020 3/3 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Wheel Spindles SMCS - 4205-12; 4205-11 Remove Wheel Spindles start by: a) remove brake shoes 1. Turn slack adjuster (3) to release any force on pin (1). 2. Remove retainer ring (2) from the brake camshaft. 3. Remove brake camshaft (5). Remove washers (4) from between the bracket assembly and slack adjuster assembly and from between the brake camshaft and spindle housing. 1/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 22. Make sure the air pressure in the brake system is zero before any lines are disconnected. 4. Disconnect air lines (6) from the chamber assembly. 5. Remove bolts (9). Remove bracket assembly (8), slack adjuster assembly and chamber assembly from the spindle assembly as a unit. 6. Fasten a hoist to the wheel spindle assembly. Remove nuts (7) and washers. Remove wheel spindle assembly (10). The weight of the wheel spindle assembly is 100 lb. (45 kg). 7. Remove O-ring seal (13) from the spindle. 2/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 23. 8. Use four 1/2"-13 NC forcing screws to remove spider and bearing assembly (12) from spindle (11). 9. Remove sleeve (14), lip seal and bearing from the spider. Install Wheel Spindles 1. Use tooling (A) to install sleeve (3) in the spider. Use tooling (A) to install bearing and lip seal in the opposite side of the spider. Install the seal with the lip toward the bearing. 2. Install spindle (4) in spider and bearing assembly (2). Put 1P808 General Purpose Lubricant in the bearing and bore of the spider assembly. 3. Install O-ring seal (1) on the spindle. 4. Fasten a hoist to the wheel spindle assembly. Install wheel spindle assembly (5) on the axle housing. Install the washers and nuts that hold it. Tighten the nuts to a torque of 345 ± 30 lb.ft. (465 ± 40 N·m). 3/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 24. 5. Install bracket assembly (7), slack adjuster assembly and chamber assembly on the spindle assembly as a unit. 6. Connect air lines (6) to the chamber assembly. 7. Install washer (8) on the brake camshaft. Install brake camshaft (9) in spider and bracket assemblies. Install washer and slack adjuster assembly (10) on brake camshaft (9). Install the retainer ring on the brake camshaft. end by: a) install brake shoes Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:42:42 UTC+0800 2020 4/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 25. Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 966C WHEEL LOADER 76J Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE Disassembly and Assembly 966 WHEEL LOADER POWER TRAIN Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001 Front Differential And Carrier SMCS - 3258-12; 3258-11 Remove Front Differential And Carrier start by: a) remove axles (front only) 1. Remove plug (1). Drain the oil from the front axle housing. 2. Remove spider and bearing assembly (4) from the front drive shaft (3) and differential pinion shaft. 1/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 26. 3. Remove yoke (2) from the differential pinion shaft. Make sure the air pressure in the brake system is zero before any lines are disconnected. 4. Disconnect three lines (5) from the tee fitting. 5. Disconnect three lines (6) from the quick release valve. 6. Disconnect clips (7) from each side of the axle housing and pull the air lines clear of the differential and carrier. 7. Fasten tooling (A) to the front differential and carrier as shown. Remove bolts (9). Install two 1/2"-13 NC forcing screws and remove differential and carrier (8) from the axle housing. The weight of the differential and carrier is 350 lb. (158 kg). Install Front Differential And Carrier 2/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 27. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 28. 1. Fasten tooling (A) to the differential and carrier as shown. Put differential and carrier (1) in position in the axle housing. Install the bolts that hold it. Tighten the bolts to a torque of 195 ± 18 lb.ft. (265 ± 24 N·m). 2. Connect three air lines (2) to the tee fitting. 3. Connect three air lines (3) to the quick release valve. 4. Connect the clips that hold the air lines in position on the axle housing. 5. Install yoke (4) on the differential pinion shaft. 3/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 29. 6. Install spider and bearing assembly (5) on the yoke and front drive shaft. Tighten the bolts to a torque of 100 ± 10 lb.ft. (135 ± 14 N·m). 7. Install the drain plug and fill the front axle housing with oil to the correct level. See LUBRICATION AND MAINTENANCE GUIDE. end by: a) install axles (front only) Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Apr 13 23:43:38 UTC+0800 2020 4/4 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI... 2020/4/13 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...