The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment and bolts/washers to remove the flywheel housing and check the oil seal for replacement.
2) Cleaning the mating surfaces and installing a new gasket before placing the housing back in position.
3) Securing the housing with bolts and installing a new oil seal and crankshaft sleeve with special tools.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 320 track type excavator (prefix 1 xm) service repair manual ...ufjdfjjkskemme
This document provides instructions for removing and installing a crankshaft pulley on an excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. For installation, the pulley is pressed back onto the crankshaft using an installer tool. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 312 b track type excavator (prefix 9gr) service repair manual...fjskkksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Removing the adapter, inner ring, and bolts to separate the flywheel.
2) Using straps and lifting tools to remove the 50kg flywheel from the housing.
3) Heating and tapping to remove the ring gear from the flywheel, if needed.
4) Reversing the process to install a new or serviced flywheel by securing it with bolts and installing the inner ring and adapter.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...fijsekkdmdm2w
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while using a tool to install a new oil seal and crankshaft sleeve.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...zan2736ban
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...idkkdmmd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Technicians should inspect the oil seal and replace if needed. For installation, technicians clean the mating surfaces, place the housing in position, and install bolts and a new gasket to secure it. They also use a special tool to install a new oil seal and crankshaft wear sleeve.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...fujkskemdmdm4r
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...idkkdmmd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator engine. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar Cat 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Repair Manua...km7seydwuhdw
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Technicians should inspect the oil seal and replace if needed. For installation, technicians clean the mating surfaces, place the housing in position, and install bolts and a new gasket to secure it. They also use a special tool to install a new oil seal and crankshaft wear sleeve.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 312B L excavator engine. It describes:
1) Using various tools to remove the flywheel adapter, inner ring, and bolts to detach the flywheel.
2) Heating and tapping the ring gear to remove it from the flywheel.
3) Lifting the 50kg flywheel out of the housing using straps and a lifting device.
4) Drilling holes in and using a slide hammer to pull the crankshaft rear seal.
5) Applying primer and retaining compound before installing a new wear sleeve and seal using an installer tool.
6) Re
Daewoo doosan solar 140 w v wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and instructions for operating and maintaining a Daewoo excavator. It includes locations of safety labels on the machine, precautions for lifting loads, unauthorized modifications, hazards, starting and operating the machine, maintenance, batteries, towing, shipping and lift capacity tables. Operators must read the manual thoroughly before use to safely handle, operate and service the excavator.
Daewoo doosan dx160 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage lines, hot fluids that can cause burns, and rotating or moving parts that can cause injury.
Daewoo doosan dx140 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage electrical lines, hot fluids that can cause burns, and rotating equipment that can cause injury.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjsjjdkemmde
This document provides an operation and maintenance manual for a Doosan wheel loader model DL420. It includes safety information, descriptions of machine components and controls, operating instructions, maintenance procedures, and specifications. Operators and maintenance personnel must read and understand the entire manual before operating or servicing the machine to avoid serious injury or death.
Daewoo doosan dl300 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies locations of safety labels on the machine and warns that unauthorized modifications could create safety hazards.
- Operators and maintenance personnel are instructed to read the entire manual before use to understand all safety precautions.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 320 track type excavator (prefix 1 xm) service repair manual ...ufjdfjjkskemme
This document provides instructions for removing and installing a crankshaft pulley on an excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. For installation, the pulley is pressed back onto the crankshaft using an installer tool. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 312 b track type excavator (prefix 9gr) service repair manual...fjskkksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Removing the adapter, inner ring, and bolts to separate the flywheel.
2) Using straps and lifting tools to remove the 50kg flywheel from the housing.
3) Heating and tapping to remove the ring gear from the flywheel, if needed.
4) Reversing the process to install a new or serviced flywheel by securing it with bolts and installing the inner ring and adapter.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...fijsekkdmdm2w
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while using a tool to install a new oil seal and crankshaft sleeve.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...zan2736ban
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...idkkdmmd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Technicians should inspect the oil seal and replace if needed. For installation, technicians clean the mating surfaces, place the housing in position, and install bolts and a new gasket to secure it. They also use a special tool to install a new oil seal and crankshaft wear sleeve.
Caterpillar Cat 312B and 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Rep...fujkskemdmdm4r
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...idkkdmmd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator engine. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Instructions are provided to check the oil seal and remove it if needed using special tools. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the housing with bolts while also installing a new oil seal and crankshaft sleeve using an installer tool.
Caterpillar Cat 312B L TRACK-TYPE EXCAVATOR (Prefix 3FS) Service Repair Manua...km7seydwuhdw
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B L excavator. The removal procedure involves using lifting equipment to remove the housing, which weighs approximately 65 lbs. Technicians should inspect the oil seal and replace if needed. For installation, technicians clean the mating surfaces, place the housing in position, and install bolts and a new gasket to secure it. They also use a special tool to install a new oil seal and crankshaft wear sleeve.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 312B L excavator engine. It describes:
1) Using various tools to remove the flywheel adapter, inner ring, and bolts to detach the flywheel.
2) Heating and tapping the ring gear to remove it from the flywheel.
3) Lifting the 50kg flywheel out of the housing using straps and a lifting device.
4) Drilling holes in and using a slide hammer to pull the crankshaft rear seal.
5) Applying primer and retaining compound before installing a new wear sleeve and seal using an installer tool.
6) Re
Similar to Caterpillar cat 312 b track type excavator (prefix 9gr) service repair manual (9gr00001 and up) (8)
Daewoo doosan solar 140 w v wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and instructions for operating and maintaining a Daewoo excavator. It includes locations of safety labels on the machine, precautions for lifting loads, unauthorized modifications, hazards, starting and operating the machine, maintenance, batteries, towing, shipping and lift capacity tables. Operators must read the manual thoroughly before use to safely handle, operate and service the excavator.
Daewoo doosan dx160 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage lines, hot fluids that can cause burns, and rotating or moving parts that can cause injury.
Daewoo doosan dx140 w wheel excavator operator and maintenance manualfjsjjdkemmde
The document provides safety information and warnings for operating an excavator. It outlines the location of safety labels on the machine and summaries key safety precautions, including: never getting under a raised machine, ensuring all people are clear before operating, and turning off the engine and removing the key before leaving the operator's seat. It also warns of hazards such as high voltage electrical lines, hot fluids that can cause burns, and rotating equipment that can cause injury.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjsjjdkemmde
This document provides an operation and maintenance manual for a Doosan wheel loader model DL420. It includes safety information, descriptions of machine components and controls, operating instructions, maintenance procedures, and specifications. Operators and maintenance personnel must read and understand the entire manual before operating or servicing the machine to avoid serious injury or death.
Daewoo doosan dl300 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies locations of safety labels on the machine and warns that unauthorized modifications could create safety hazards.
- Operators and maintenance personnel are instructed to read the entire manual before use to understand all safety precautions.
Daewoo doosan dl200 tc wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using safety features properly, operating only if feeling well, and being aware of hazards inside the operator's cabin.
Daewoo doosan dl200 wheel loader operator and maintenance manualfjsjjdkemmde
- The document provides safety information and instructions for operating and maintaining a Doosan wheel loader.
- It identifies the location of safety labels on the machine and warns that unauthorized modifications can create safety hazards.
- General safety rules include using the machine as intended, following all safety procedures, and ensuring safety features like guards are in good condition.
Daewoo doosan 470 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan 460 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 460 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Daewoo doosan 450 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an informational guide for service teams working on Doosan loaders overseas.
Daewoo doosan 440 plus skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document is intended as an instruction manual for servicing Doosan loaders overseas.
Daewoo doosan 430 skid steer loader operator and maintenance manualfjsjjdkemmde
This document provides an overview of Doosan skid steer loaders for overseas service teams. It covers general information about Doosan loader models and specifications. It also outlines the operation section, including safety, the operating room, and instrument panel. The document contains detailed explanations and diagrams.
Caterpillar cat 330 f l excavator (prefix wba) service repair manual (wba0000...fjsjjdkemmde
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, brake piston, rotating group, pistons, and seals. Various tools are required, including retaining ring pliers, a bearing puller, threaded rods, nuts, and washers to secure and remove parts safely. Care must be taken to avoid damage and properly release spring forces during disassembly.
Caterpillar cat 330 f l excavator (prefix lcg) service repair manual (lcg0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly including gears, shafts, housings, seals and bearings. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating and installing each part in the proper order and orientation using torque specifications where required.
Caterpillar cat 330 f l excavator (prefix kfa) service repair manual (kfa0000...fjsjjdkemmde
The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove it, a tool is used to prevent the crankshaft from rotating while the pulley assembly screws are removed with a torque socket. The assembly is then lifted off. To install it, the components are assembled in reverse order and tightened using guide studs and torque specifications are followed. The process involves up to 21 steps and requires the use of 4 tools.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix hck) service repair manual (hck0000...fjsjjdkemmde
This document provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, friction discs, and rotating group. Various tools are required, and care must be taken due to spring forces. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 330 f l excavator (prefix ght) service repair manual (ght0000...fjsjjdkemmde
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567208
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing screws M16 X 2 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00605492
1. Remove twelve bolts (1) and washers from the adapter (2) .
2. Remove the adapter (2) from the flywheel housing.
Illustration 2 g00605497
3. Remove four socket head bolts (3) from the inner ring (4) .
4. Remove the inner ring (4) from the flywheel.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605501
5. Remove six bolts (5) that secure flywheel (6) to the crankshaft. Check all bolts for stripped
threads. Replace the bolts, if necessary.
Illustration 4 g00605504
6. Install Tool (A), a strap, and a suitable lifting device onto the flywheel (6).
7. Use Tool (B) in order to remove the flywheel and ring gear out of the housing. The weight
of the flywheel is 50 kg (110 lb).
8. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 5 g00613038
a. Place the flywheel and ring gear assembly on a suitable support.
Note: Check the flywheel ring gear for the following conditions:cracks, damaged
dowel holes, worn ring gear and damaged ring gear.
Note: Identify the orientation of the old ring gear on the flywheel for proper
positioning, when the new ring gear is installed.
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Always wear protective gloves when handling parts that have been
heated.
b. Heat ring gear (7) uniformly.
c. Remove the ring gear (7) by tapping the ring gear all the way around the flywheel
(6) .
d. Reposition the flywheel in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:25:57 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:26:57 UTC+0800 2020
3/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:28:55 UTC+0800 2020
3/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:29:54 UTC+0800 2020
3/3
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:30:54 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:31:53 UTC+0800 2020
2/2
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 08:32:52 UTC+0800 2020
2/2
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9GR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
312B & 312B L TRACK-TYPE EXCAVATORS 9GR00001-UP (MACHINE) POWE...
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...