service repair manual

2. Airbags
1.
AudioVisual
2.
Axle
3.
BrakeControl
4.
Brakes
5.
Charging1gr
6.
Charging2uz
7.
Cooling1gr
8.
Cooling2uz
9.
CruiseControl
10.
Differential
11.
Driveshaft
12.
ElectricalComponentLocations
13.
EmissionControl1gr
14.
EmissionControl2uz
15.
Engine1gr
16.
Engine2uz
17.
EngineControl1gr
18.
EngineControl2uz
19.
Exhaust1gr
20.
Exhaust2uz
21.
Exterior
22.
Fuel1gr
23.
Fuel2uz
24.
HoodDoors
25.
Horns
26.
Hvac
27.
Ignition1gr
28.
Ignition2uz
29.
InstrumentPanel
30.
Intage1gr
31.
Intake2uz
32.
InteriorTrim
33.
Lighting
34.
Lubrication1gr
35.
Lubrication2uz
36.

3. Mirrors
37.
Navigation
38.
ParkingBrakes
39.
PowerDoorLocks
40.
PowerSteering
41.
PropellerShaft
42.
Seats
43.
ServiceSpecs
44.
Starter1gr
45.
Starter2uz
46.
SteeringColumn
47.
Sunroof
48.
SuspensionControl
49.
Suspension
50.
Windows
51.
WiperWasher
52.
Wiring
53.

4. 2008 DRIVELINE/AXLES
Differential - 4Runner
DIFFERENTIAL SYSTEM
PRECAUTION
1. Before disassembly, clean the outside of the front and rear differential assembly and remove any
sand and mud to prevent it from entering the assembly during disassembly and installation.
2. When removing connected parts made of a light alloy, such as front and rear differential carrier
covers, tap them off with a plastic hammer. Do not attempt to pry them off with a screwdriver.
3. Always arrange disassembled parts in order and protect them from dust.
4. Before installation, thoroughly clean and dry each part and then apply hypoid gear oil LSD to it.
Do not use alkaline cleaner for aluminum or rubber parts and ring gear set bolts. Also, do not clean
rubber parts such as O-rings or oil seals with white gasoline.
5. Coat all sliding surfaces and rotating parts with hypoid gear oil LSD.
6. When holding components in a vice, be sure to place an aluminum sheet under the M part. Do not
put them directly in the vice.
7. Be careful not to damage the contact surfaces of the case. Such damage could cause oil leakage.
8. Before applying sealant, remove any deposited oil sealant and clean the part to be sealed using
white gasoline.
9. Do not supply oil immediately after installing sealed parts. Leave them for at least an hour.
10. Damage to the surfaces in direct contact with oil seals, O-rings or gaskets could cause oil leakage.
Special attention should be paid.
11. When press-fitting an oil seal, be careful not to damage the oil seal lip and outside periphery.
12. When replacing a bearing, replace the inner and outer races as a set.
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of
probability of each of the possible causes. Check each part in order. If necessary, replace these parts.
DIFFERENTIAL SYSTEM
PROBLEM SYMPTOMS CHART
Symptom Suspected area Go To
Oil leakage from front differential
1. Oil level (Too high or wrong
grade)
DIFFERENTIAL OIL
2. Front differential rear oil seal
(Worn or damaged)
INSTALLATION
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Wednesday, August 05, 2009 3:48:13 PM Page 1 © 2005 Mitchell Repair Information Company, LLC.

5. DIFFERENTIAL OIL
ADJUSTMENT
1. INSPECT DIFFERENTIAL OIL
a. Stop the vehicle on a level place.
b. Remove the differential filler plug and gasket.
c. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.
3. Companion flange (Loose or
damaged) (1GR-FE)
INSTALLATION
4. Companion flange (Loose or
damaged) (2UZ-FE)
INSTALLATION
Oil leakage from rear differential
1. Oil level (Too high or wrong
grade)
DIFFERENTIAL OIL
2. Rear differential front oil seal
(worn or damaged)
REMOVAL
3. Companion flange (Loose Or
damaged)
INSPECTION
Oil leak from front drive pinion
shaft
1. Oil level (Too high or wrong
grade)
DIFFERENTIAL OIL
2. Front differential rear oil seal
(Worn or damaged)
INSTALLATION
3. Companion flange (Loose or
damaged) (1GR-FE)
INSTALLATION
4. Companion flange (Loose or
damaged) (2UZ-FE)
INSTALLATION
Oil leak from rear drive pinion
shaft
1. Oil level (Too high or wrong
grade)
DIFFERENTIAL OIL
2. Rear differential front oil seal
(Worn or damaged)
INSTALLATION
3. Companion flange (Loose or
damaged)
INSTALLATION
NOTE:  Excessively large or small quantities of oil may cause problems.
 After replacing the oil, drive the vehicle and check the oil level
again.
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 2 © 2005 Mitchell Repair Information Company, LLC.

6. Fig. 1: Identifying Differential Oil Level
HINT:
If necessary, fill the rear differential carrier assembly with hypoid gear oil.
Oil grade: Hypoid gear oil API GL-5
Recommended viscosity: Above -18°C (0°F) SAE 90
Below -18°C (0°F) SAE 80W or 80W-90
Capacity:
Front differential carrier assembly: 1.35 to 1.45 litters
(1.43 to 1.53 US qts, 1.19 to 1.27 Imp. qts)
Rear differential carrier assembly
3.00 to 3.10 litters
(3.17 to 3.27 US qts, 2.64 to 2.72 Imp. qts)
d. Check for oil leakage if the oil level is low.
e. Install the differential filler plug and a new gasket.
Torque: Front differential carrier assembly
39 N*m (398 kgf*cm, 29 ft.*lbf)
Rear differential carrier assembly
49 N*m (500 kgf*cm, 36 ft.*lbf)
REAR DIFFERENTIAL CARRIER OIL SEAL
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 3 © 2005 Mitchell Repair Information Company, LLC.

7. COMPONENTS
Fig. 2: Identifying Rear Differential Carrier Oil Seal Components With Torque Specifications
REMOVAL
1. DRAIN DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
2. REMOVE PROPELLER SHAFT ASSEMBLY
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 4 © 2005 Mitchell Repair Information Company, LLC.

8. a. Place matchmarks on the propeller shaft flange and differential flange.
b. 2WD Drive Type:
Remove the 4 nuts and 4 washers.
c. 4WD Drive Type:
Remove the 4 nuts, 4 bolts and 4 washers.
d. Suspend the propeller shaft assembly with wire or similar.
Fig. 3: Identifying Matchmarks On Propeller Shaft Flange
3. REMOVE REAR DRIVE PINION NUT
a. Using SST and a hammer, unstake the nut.
SST 09930-00010
Fig. 4: Unstaking Nut
b. Using SST to hold the companion flange, remove the nut.
SST 09330-00021
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 5 © 2005 Mitchell Repair Information Company, LLC.

9. Fig. 5: Holding Companion Flange
4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR
a. Using SST, remove the companion flange.
SST 09950-30012 (09951 -03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)
Fig. 6: Removing Companion Flange
5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
a. Using SST, remove the oil seal.
SST 09308-10010
6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Fig. 7: Removing Oil Seal
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:07 PM Page 6 © 2005 Mitchell Repair Information Company, LLC.

10. 7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
a. Using SST, remove the front bearing.
SST 09556-22010
b. Using SST, remove the front bearing outer race.
SST 09308-00010
c. Using a screwdriver, bend the oil storage ring and remove it.
8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Fig. 8: Removing Front Bearing Outer Race
INSTALLATION
1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
a. Install a new rear differential drive pinion bearing spacer.
2. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
a. Using a brass bar and a hammer, install a new oil storage ring.
b. Using SST and a hammer, install the front bearing outer race.
c. Install the front bearing.
SST 09316-60011 (09316-00011, 09316-00021)
3. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
4. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
a. Using SST and a hammer, install a new oil seal.
SST 09554-30011
Oil seal drive in depth: 0.7 to 1.3 mm (0.0276 to 0.0512 in.)
b. Coat oil seal lip with MP grease.
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 7 © 2005 Mitchell Repair Information Company, LLC.

11. Fig. 9: Installing Oil Seal
5. INSTALL REAR DRIVE COMPANION FLANGE SUB-ASSEMBLY REAR
a. Using SST, install the companion flange.
SST 09950-30012 (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)
b. Coat the threads of a new nut with hypoid gear oil LSD.
Fig. 10: Installing Companion Flange
c. Using SST to hold the companion flange, tighten the nut.
SST 09330-00021 (09330-00030)
Torque: 215 N*m (2,190 kgf*cm, 159 ft.*lbf)
Fig. 11: Holding Companion Flange
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 8 © 2005 Mitchell Repair Information Company, LLC.

12. 6. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
a. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring rear.
New bearing: 1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf)
Reused bearing: 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)
If necessary, disassemble and inspect the differential assembly.
Fig. 12: Measuring Preload Of Backlash Between Drive Pinion And Ring Rear
7. INSTALL REAR DRIVE PINION NUT
a. Using a chisel and a hammer, stake the nut.
Fig. 13: Staking Nut
8. INSTALL PROPELLER SHAFT ASSEMBLY
a. Align the matchmarks on the propeller shaft differential flange.
b. 2WD Drive Type:
Install the propeller shaft with the 4 washers and 4 nuts.
Torque: 88 N*m (897 kgf*cm, 65 ft.*lbf)
c. 4WD Drive Type:
Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 9 © 2005 Mitchell Repair Information Company, LLC.

13. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

14. Fig. 14: Identifying Matchmarks On Propeller Shaft Flange
Torque: 88 N*m (897 kgf*cm, 65 ft.*lbf)
9. FILL UP DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
10. INSPECT DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (FOR 4WD)
COMPONENTS
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 10 © 2005 Mitchell Repair Information Company, LLC.

15. Fig. 15: Identifying Differential Side Gear Shaft Oil Seal Components (For 4WD)
REMOVAL
1. REMOVE FRONT WHEEL
2. REMOVE ENGINE UNDER COVER ASSEMBLY REAR
a. Remove the 6 bolts and engine under cover assembly rear.
3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
a. Remove the 4 bolts and No. 1 engine under cover sub-assembly.
4. DRAIN DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
5. REMOVE FRONT AXLE HUB LH NUT (See REMOVAL )
6. SEPARATE FRONT SPEED SENSOR LH (See REMOVAL )
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 11 © 2005 Mitchell Repair Information Company, LLC.

16. 7. SEPARATE TIE ROD END SUB-ASSEMBLY LH (See REMOVAL )
8. SEPARATE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH (See
REMOVAL )
9. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (See REMOVAL )
10. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
a. Using SST, remove the oil seal.
SST 09308-00010
Fig. 16: Removing Oil Seal
INSTALLATION
1. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
a. Using SST and a hammer, install a new oil seal.
SST 09554-30011
b. Coat the oil seal lip with MP grease.
2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (See INSTALLATION )
3. CONNECT NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH (See
INSTALLATION )
Fig. 17: Installing Oil Seal
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 12 © 2005 Mitchell Repair Information Company, LLC.

17. 4. CONNECT TIE ROD END SUB-ASSEMBLY LH (See INSTALLATION )
5. CONNECT FRONT SPEED SENSOR LH (See INSTALLATION )
6. INSTALL FRONT AXLE HUB LH NUT (See INSTALLATION )
7. FILL UP DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
8. INSPECT DIFFERENTIAL OIL (See DIFFERENTIAL OIL )
9. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
a. Install the No. 1 engine under cover sub-assembly with the 4 bolts.
10. INSTALL ENGINE UNDER COVER ASSEMBLY REAR
a. Install the engine under cover assembly with the 6 bolts.
11. INSTALL FRONT WHEEL
Torque: 112 N*m (1,142 kgf*cm, 83 ft.*lbf)
12. INSPECT ABS SPEED SENSOR SIGNAL
HINT:
(See TEST MODE PROCEDURE )
1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (FOR 4WD)
COMPONENTS
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 13 © 2005 Mitchell Repair Information Company, LLC.

18. Fig. 18: Identifying 1GR-FE Front Differential Carrier Assembly Components With Torque
Specifications - For 4WD (1 Of 3)
2008 Toyota 4Runner Limited
2008 DRIVELINE/AXLES Differential - 4Runner
Microsoft
Wednesday, August 05, 2009 3:48:08 PM Page 14 © 2005 Mitchell Repair Information Company, LLC.