The document provides instructions for removing and installing a quick coupler hydraulic system component on a Caterpillar 277 Multi Terrain Loader. The removal procedure involves releasing hydraulic pressure, removing bolts and pins, and lifting out the quick coupler. The installation procedure specifies cleaning and lubricating parts, positioning the coupler, and installing bolts and pins in reverse order of removal. Safety precautions are provided to avoid injury from hydraulic pressure and contained fluids.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
The Future of Autonomous Vehicles | civilthings.com | Detailed informationgettygaming1
civilthings.com Present Autonomous vehicles, also known as self-driving cars, represent a groundbreaking advancement in transportation technology. These vehicles utilize sophisticated sensors, advanced software, and machine learning algorithms to navigate roads and transport passengers without human intervention. Major companies in the autonomous vehicle industry are investing heavily in the development and testing of these innovative machines, aiming to enhance safety, efficiency, and convenience on the roads.
The autonomous vehicle market is rapidly expanding, driven by technological progress and increasing consumer interest. With the advent of autonomous vehicle technology, the future of transportation promises significant changes, including reduced traffic accidents and lower emissions. However, the widespread adoption of autonomous vehicles faces challenges, such as regulatory hurdles, safety concerns, and public acceptance.
Autonomous vehicle regulations and legislation are evolving to address these issues, ensuring that the integration of self-driving cars into everyday life is smooth and secure. As the industry grows, news and trends related to autonomous vehicles continue to capture global attention. From the development of cutting-edge sensors to advancements in autonomous vehicle software, this sector is poised to revolutionize how we think about mobility.
Stay informed about the latest in autonomous vehicle technology, industry developments, and market trends to understand the profound impact these vehicles will have on our future.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
2. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277 MULTI TERRAIN LOADER CNC
Configuration: 267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
267, 277 and 287 Multi Terrain Loaders Machine Systems
Media Number -RENR4816-03 Publication Date -01/10/2009 Date Updated -29/10/2009
i01989030
Quick Coupler - Remove and Install - Hydraulic
SMCS - 6129-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 140-7742 Sleeve 2
ZZ
6V-9507 Face Seal Plug 4
6V-9828 Cap As 4
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
1/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
1. Remove the work tool. Refer to Operation and Maintenance Manual, "Work Tool Coupler
Operation".
Illustration 1 g01030155
2/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Disconnect hose assemblies (1) .
Illustration 2 g01030156
3. Position the quick coupler on blocks, as shown. Remove bolts (2) and guard (3) .
Illustration 3 g01030159
4. Remove bolts (4) and bolt (5). Reposition the hose assemblies out of the way.
3/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01030161
5. Attach Tooling (A) and a suitable lifting device to quick coupler (6). The weight of the
quick coupler is approximately 98 kg (215 lb).
Illustration 5 g01030162
6. Remove bolt (8) and pin assembly (7) .
Illustration 6 g01030163
7. Remove bolt (10) and pin assembly (9) .
8. Repeat Step 6 and Step 7 for the other side.
9. Use the suitable lifting device to remove quick coupler (6). The weight of quick coupler (6)
is approximately 98 kg (215 lb).
Installation Procedure
Table 2
4/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Required Tools
Tool Part Number Part Description Qty
A 140-7742 Sleeve 2
B 5P-0960 Molybdenum Grease 1
Note: The pins, the bores, and the bearings must be clean before assembling.
1. Apply Tooling (B) in order to lubricate the pins, the bores, and the bearings before
assembling.
Illustration 7 g01030163
2. Attach Tooling (A) and a suitable lifting device to quick coupler (6). The weight of quick
coupler (6) is approximately 98 kg (215 lb). Position quick coupler (6). Use blocks to
support the quick coupler.
3. Install pin assembly (9) and bolt (10) .
Illustration 8 g01030162
4. Install pin assembly (7) and bolt (8) .
5/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 5. Repeat Step 3 and Step 4 for the other side.
6. Remove the suitable lifting device and Tooling (A) .
Illustration 9 g01030159
7. Reposition the hose assemblies and install bolts (4) and bolts (5) .
Illustration 10 g01030156
8. Install guard (3) and bolts (2) .
6/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g01030155
9. Connect hose assemblies (1) .
10. Install the work tool. Refer to Operation and Maintenance Manual, "Work Tool Coupler
Operation".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 8 22:12:14 UTC+0800 2019
7/7
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277 MULTI TERRAIN LOADER CNC
Configuration: 267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
267, 277 and 287 Multi Terrain Loaders Machine Systems
Media Number -RENR4816-03 Publication Date -01/10/2009 Date Updated -29/10/2009
i01991495
Solenoid Valve and Mounting (Coupler) - Remove and Install
- 267 and 277 Multi Terrain Loader
SMCS - 5479-010-MT; 5479-010
S/N - CMP1-UP
S/N - CNC1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ
6V-9508 Face Seal Plug 3
6V-9829 Cap As 3
6V-9509 Face Seal Plug 1
6V-9830 Cap As 1
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Raise the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Personal injury can result from hydraulic oil pressure and hot oil.
1/4
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
2/4
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. End By: Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 8 22:13:13 UTC+0800 2019
4/4
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277 MULTI TERRAIN LOADER CNC
Configuration: 267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
267, 277 and 287 Multi Terrain Loaders Machine Systems
Media Number -RENR4816-03 Publication Date -01/10/2009 Date Updated -29/10/2009
i01807309
Coupler Cylinder - Remove and Install
SMCS - 5133-010
Removal Procedure
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure Release".
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/5
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g00924287
1. Disconnect hose assemblies (1) .
2/5
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00924288
2. Remove pin (2). Remove pin (3). Remove coupler cylinder and link assembly (4) .
3. Repeat Step 2 for the other side.
Installation Procedure
3/5
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g00924288
1. Install coupler cylinder and link assembly (4). Install pin (3). Install pin (2) .
2. Repeat Step 1 for the other side.
Illustration 4 g00924287
4/5
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 3. Connect hose assemblies (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 8 22:14:12 UTC+0800 2019
5/5
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 277 MULTI TERRAIN LOADER CNC
Configuration: 267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
267, 277 and 287 Multi Terrain Loaders Machine Systems
Media Number -RENR4816-03 Publication Date -01/10/2009 Date Updated -29/10/2009
i01934149
Tilt Cylinder - Remove and Install
SMCS - 5104-010
Removal Procedure
Table 1
REQUIRED TOOLS
Tool Part Number Part Description Qty
A 180-3034 Repair Stand Set 2
B
4C-5655 Adapter 1
5F-7345 Threaded Rod (5/8 inch by 18 NF by 16 inch) 1
1P-0074 Slide Hammer Puller Gp 1
6B-6683 Nuts 2
ZZ
6V-9509 Face Seal Plug 4
6v-9830 Cap As 4
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Remove the quick coupler. Refer to Disassembly and Assembly, "Quick Coupler - Remove
and Install".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
1/8
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
2/8
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01006547
1. Use Tooling (A) to support the lift arms.
Illustration 2 g00889759
2. Disconnect hose assembly (1). Disconnect hose assembly (2) .
3/8
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
22. Illustration 3 g00889760
Illustration 4 g00909073
3. Remove bolt (3) .
4. Use a suitable lifting device to support tilt cylinder (5). Use Tooling (B) to remove pin (4).
Remove cylinder (5) .
5. Repeat Steps 2 through 4 for the other side.
Disassembly and Assembly Information
Table 2
Required Tools
Tool Part Number Part Description Qty
C 127-4904 Repair Stand 1
D 195-4609 Seal Pick 1
F 5P-0960 Molybdenum Grease
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
4/8
267 277 Multi Terrain Loader CNC00001-UP (MACHINE) POWERED BY 3034 Eng...
2019/11/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...