The latest addition to the EZstrip™ family is a range of grinders offering a competitive solution to solids grinding and sludge conditioning. The EZstrip™ TR Munchers® all house the quick release access port allowing the cutter assembly to be maintained in place without removing the equipment, reducing maintenance time.

1. EZstrip™
TR Muncher®

2. Grinder Challenge
Traditional grinder maintenance
requires full removal from the
pipe work to replace the grinder's
cutters, spacers, and shafts.
This job is strained by reduced
maintenance budgets and
diminishing in-house expertise.
Pull out cutter stack cartridge
EZ Solution allows removal without disturbing
The EZstrip™ series of grinders pipeline or electrical connection.
offer a competitive solution
to solids grinding and sludge
conditioning. The EZstrip™
TR Munchers® include the
quick access port allowing the
cutter stack assembly to be
maintained-in-place reducing
maintenance time from an entire Angled cutter stack "upflow" design
rejects hard materials reducing the
day to just a few hours.
risk of damage to the cutter teeth.
Maintain-in-Place
Capabilities
• Reduces the time and effort
required for maintenance
• Eases removal of rotating
parts without disconnecting
the electrical connection to
the unit Built-in trash trap is situated below and away
• Eliminates the need for from the cutter stack to catch any rejected
removing housing from the material. Rejected items can be removed or
pipe work flushed out through the clean out port.
• No special tools required

3. Service Exchange
Pre-assembled cartridge is
available with a 2-year warranty
to allow faster reassembly time
Eliminate Dismantling Space
Side-mounted During Maintenance
CT201 applicable Suction and discharge ports
for smaller flow remain connected to pipe work
rates.
Cartridge Assembly
Short lead times for cutter stack
cartridge replacement units
ETOS (Equal Thrust Offset) cutters
capture and reduce large solids for
effective maceration.
Energy Efficient Motors
Efficient motors along with low
installation power to further
reduce operating costs
Low Running Speeds
Cantilever design eliminates the need
for lower mechanical seals or bearings
Reduced wear for longer working
reducing breakdowns and repair costs. life and extended periods
between routine maintenance

4. Time and Cost Savings
EZstrip™ TR Muncher® provides a quick and easy answer to maintain your grinder in place, reducing
maintenance time by more than 70% for significant cost savings.
You'll save more than $4,700* over the life of one EZstrip™ TR Muncher® compared to a standard
grinder.
To see the EZstrip™ TR Muncher® in action, visit www.EZstrip.com.
EZstripTM TR Muncher® Standard Grinder Maintenance
$9,000 Time
$8,000
Maintenance Cost Over Pump Life ($)
$7,000 12
11 1
$6,000
10 2
$5,000
9 3
$4,000
8 4
$3,000
7 5
$2,000 6
$1,000
$0 EZstripTM TR Muncher®
reduces grinder maintenance
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
time from ten and half hours
Number of Years to three hours.
Assumptions: Labor cost per hour is $60, grinder type is CT203 (6"), flow rate is 400 gpm, pump life is 15 years, maintenance
inspection is 30 minutes once a year, maintenance intervention is 2.5 hours every two years, and inflation rate of 3%

5. CT203 & CT205 Performance Data
7.00 7.00
10% DS 8% DS 6% DS 4% DS 2% DS 0% DS 10% DS 8% DS 6% DS 4% DS 2% DS 0% DS
6.00 6.00
CT203R CT205T
(8”) (12”)
5.00 5.00
Pressure Diff (PSI)
Pressure Diff (PSI)
4.00 4.00
CT205S
3.00 3.00
CT203Q
CT203 (10”) CT205
(6”)
2.0 HP 2.0 HP
2.00 2.00
CT203P 3.0 HP 3.0 HP
(4”)
1.00 1.00
5.0 HP 5.0 HP
0.00 0.00
0 100 200 300 400 500 600 700 800 900 1,000 1,100 1,200 0 500 1,000 1,500 2,000 2,500
Capactiy (US GPM) Capactiy (US GPM)
CT203 & CT205 Dimensions
21.34
I
E
K
C
'L' HOLES Ø'M'
ON A 'N' PCD
O
A
D
4-HOLES Ø18
10.63 0.98 J 0.98
0.79 12.60 G H
B F
MODEL HP A B C D E F G H I J K L M N O LBS.
CT203P 3.94 14.57 40.15 8.07 0.94 19.25 16.14 4.88 5.51 14.17 14.29 0.31 0.71 7.09 8.66 639
CT203Q 5.90 14.57 40.15 9.06 0.98 21.26 16.14 6.10 1.57 14.17 13.94 0.31 0.87 9.45 11.22 639
CT203R 2.0 7.87 14.57 40.15 10.08 1.14 23.27 16.14 8.07 0.63 14.17 13.82 0.47 0.87 11.61 13.50 639
CT205S 9.84 14.57 46.85 11.06 1.26 27.24 18.11 8.07 1.18 16.14 19.45 0.47 1.02 13.98 15.98 760
CT205T 11.81 14.57 46.85 13.07 1.26 31.26 18.11 10.35 -0.67 16.14 18.58 0.47 1.02 16.14 19.01 760
CT203P 3.94 15.55 44.49 8.07 0.94 19.25 16.14 4.88 6.65 14.75 14.29 0.31 0.71 7.09 8.66 749
CT203Q 5.90 15.55 46.06 9.06 0.98 21.26 16.14 6.10 3.82 14.17 13.94 0.31 0.87 9.45 11.22 749
CT203R 3.0 - 5.0 7.87 15.55 46.06 10.08 1.14 23.27 16.14 8.07 2.83 14.17 13.82 0.47 0.87 11.61 13.50 749
CT205S 9.84 15.55 51.57 11.06 1.26 27.24 18.11 8.07 3.43 16.14 19.45 0.47 1.02 13.98 15.98 860
CT205T 11.81 15.55 51.57 13.07 1.26 31.26 18.11 10.35 1.57 16.14 18.58 0.47 1.02 16.14 19.01 860
All dimensions are in inches and for guidance only.
For full certified drawings or assistance in selecting a pump, visit www.monoflo.com.

6. CT201 Performance Data
5.07
8% DS 6% DS 4% DS 2% DS 0% DS
4.35
3.62
Pressure Diff (PSI)
2.90
2.17
1.45
2.0 HP
0.72
3.0 HP
0.00
0 88 176 264 352 440 528 616
Capactiy (US GPM)
CT201 Dimensions
B MODEL HP A B C D LBS.
CT201Q 2.0 27.55 7.32 15.78 27.55 308
CT201Q 3.0 28.15 7.99 16.93 28.74 385
All dimensions are in inches and
for guidance only. For full certified
8 HOLES TAP drawings or assistance in selecting a
M16 x 20 DEEP pump, visit www.monoflo.com.
EQUI-SPACED ON
A 240 PCD
1.02 (OPPOSITE FLANGE
1.02
IDENTICAL)
A
5.91
8.46
8.27
10.24
0.79 4 HOLES DRILL 10.24
Ø 18 THRO' 0.79
11.81
C 11.81
13.07
D
United States of America Canada New Zealand China
Houston, Texas Lloydminster, Alberta Auckland Shanghai
+1 281 200 1200 +1 780 875 5504 +64 (0)9 829 0333 +86 (0)21 3990 4588
monoflo@nov.com info.monoflo@nov.com info@mono-pumps.co.nz monoshanghai@nov.com
Argentina France United Kingdom Australia
Buenos Aires Rebeuville, Lorraine Manchester, England Melbourne, Victoria
+54 11 4290 9940/50 +33 (0)3 29 94 26 88 +44 (0)161 339 9000 1 (800) 333 138
monoflo@nov.com dmi-est@dmi-est.fr info-mono@nov.com ozsales@mono-pumps.com
Published information other than marked CERTIFIED does not extend any warranty or representation, expressed
or implied, regarding these products. Any such warranties or other terms and conditions of sales and products
shall be in accordance with NOV Monoflo’s standard terms and conditions of sale available for request.
NOV Monoflo® products are marketed outside North America under the trademark NOV Mono®.
Literature reference: EZP-R1 2011
NOV Monoflo® is a registered trademark of Mono Pumps Ltd.
www.monoflo.com