1. 9.75
19.50
5.5
2.0 (x2)
AA
2.44±0.03*
SPIB2
3.3 (x2)
5.0
8.750.5(x2)
0.5(x2)
CC
B
B
E
D
SECTION A-A
4.0 (x3) +0.5 D.P.S.
2.2 (x3)
2.4(x3)
240°(x3)
4.2 (x6) REF.
SECTION C-C
1.2
2.8
3.0
SECTION B-B
0.30
0.77
DETAIL E
SCALE 10 : 1
ELIPTICAL SHAPE
ALL AROUND
SHARP CORNER
ALL AROUND
1.0(x6)
tobeoptimized
after1-stinjection
DETAIL D
SCALE 10 : 1
Notes: Unless otherwise specified
1. Material: EMS Grivory, Grilamid LV-5/KN-1H.
Virgin Resin only. Recycled material is not allowed.
2. Drawing not to scale.
3. In case of mismatch between the drawing and the 3D file,
the 3D file is the correct reference.
4. Inspection Dimension shall be marked with an oval " “ around the dimension.
Dimension value required in the report. No Cpk requirements.
5. Key Inspection Dimension shall be marked with an oval “ “ around the dimension and
an asterisk “*” after the dimension inside the oval.
Dimension value required in the report. Dimension to achieve Cpk > = 1.33
6. Draft angles according to 3D file.
7. Maximum flash allowed 0.1 mm. Max thickness allowed 0.05 mm.
8. Maximum mismatch allowed - 0.05 mm.
9. Maximum ejector marks should be flash up to 0.2 mm below surface.
10. Gating cut off should be flush to ± 0.2mm.
11. Cavity mark acc. to 3D file. Protrusion 0.2 mm.
12. Surface finish: see marked area-SPI B2
13. All other surfaces finish: VDI-3400 #24-27 or better.
14. D.P.S.-Denote Draft Per Side.
15. Final geometry of the part for tool must be approved by Covidien engineering
prior to construction of tool.
REV DESCRIPTION DATE DRAWER DESIGNER
00 04/01/2015
01 29/01/2015
© 2012 Oridion Medical 1987 Ltd. All rights reserved.
FILE NAME:
7) SHEETMETAL BENDING
TOL. ARE AS FOLLOWS:
0.5 - 120 ±0.3
120 - 400 ±0.5
400 - 1000 ±1.0
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF ORIDION. ANY REPRODUCTION IN
PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF
ORIDION IS PROHIBITED.
NanomediCO2
WEIGHT [gr]:
Oridion®
NAME
FM Body
SEE NOTE 1
20/11/2013
04/01/2015
Yigal K.
Yigal K.
10138357 01
A3
5:1
REV.:DWG.No.:
DATE
DESIGNED
DRAWN
OF
8) THREAD CHAMFERS:
MALE:45° TO MINOR DIA.
FEMALE:45° TO MAJOR DIA
5) MACHINING TOL. ACCORDING
TO ISO 2768mk AS FOLLOWS:
0.5 - 6 ±0.1 120 - 400 ±0.5
6 - 30 ±0.2 400 - 1000 ±0.8
30 - 120 ±0.3 1000- 2000 ±1.2
UNLESS OTHERWISE SPECIFIED
1)DIMENSIONS APPLY AFTER COATING
2)DO NOT SCALE DRAWING
3)ALL DIMENSIONS ARE IN MM
4)BREAK CORNERS AND EDGES 0.2 MAX
SIZE
MATERIAL:
DESCRIPTION:
PROJECT:
SURFACE
ROUGHNESS:
SHEET
SCALE:
ELECTRONIC APPROVALS, EFFECTIVITY INFORMATION, AND LIFECYCLE STATUS CAN BE
OBTAINED BY ACCESSING THE SYSTEM GENERATED APPROVAL PAGE ASSOCIATED WITH
THIS DOCUMENT.THE SYSTEM GENERATED APPROVAL PAGE CAN BE RETRIEVED FROM THE
PDM SYSTEM.
1
2
6) PLASTIC INJECTED TOL. ACCORDING
TO DIN 16742, SEE TABLE IN UPPER
LEFT CORNER ON SHEET 1
PROPRIETARY AND CONFIDENTIAL.snapstorageUsersYigal.KrayzMy DocumentsNANOFlow mesurement10138357
10138357
- 1.0
All materials and processes which are used to produce this part must comply with RoHS and EU REACH directives.

2. SPI B2
3.0
CAVITY NUMBER
8.9
5.1
13.7
6.7
90°
26.0
R0.5
5.4
SPI B2
© 2012 Oridion Medical 1987 Ltd. All rights reserved.
FILE NAME:
7) SHEETMETAL BENDING
TOL. ARE AS FOLLOWS:
0.5 - 120 ±0.3
120 - 400 ±0.5
400 - 1000 ±1.0
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF ORIDION. ANY REPRODUCTION IN
PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF
ORIDION IS PROHIBITED.
NanomediCO2
WEIGHT [gr]:
Oridion®
NAME
FM body
SEE NOTE 1
20/11/2013
04/01/2015
Yigal K.
Yigal K.
10138357 01
A3
5:1
REV.:DWG.No.:
DATE
DESIGNED
DRAWN
OF
8) THREAD CHAMFERS:
MALE:45° TO MINOR DIA.
FEMALE:45° TO MAJOR DIA
5) MACHINING TOL. ACCORDING
TO ISO 2768mk AS FOLLOWS:
0.5 - 6 ±0.1 120 - 400 ±0.5
6 - 30 ±0.2 400 - 1000 ±0.8
30 - 120 ±0.3 1000- 2000 ±1.2
UNLESS OTHERWISE SPECIFIED
1)DIMENSIONS APPLY AFTER COATING
2)DO NOT SCALE DRAWING
3)ALL DIMENSIONS ARE IN MM
4)BREAK CORNERS AND EDGES 0.2 MAX
SIZE
MATERIAL:
DESCRIPTION:
PROJECT:
SURFACE
ROUGHNESS:
SHEET
SCALE:
ELECTRONIC APPROVALS, EFFECTIVITY INFORMATION, AND LIFECYCLE STATUS CAN BE
OBTAINED BY ACCESSING THE SYSTEM GENERATED APPROVAL PAGE ASSOCIATED WITH
THIS DOCUMENT.THE SYSTEM GENERATED APPROVAL PAGE CAN BE RETRIEVED FROM THE
PDM SYSTEM.
2
2
PROPRIETARY AND CONFIDENTIAL.snapstorageUsersYigal.KrayzMy DocumentsNANOFlow mesurement10138357
10138357
- 1.0
6) PLASTIC INJECTED TOL. ACCORDING
TO DIN 16742, SEE TABLE IN UPPER
LEFT CORNER ON SHEET 1