The document discusses lyophilization and elutriation. Lyophilization, or freeze drying, is a process that removes water from a frozen product under vacuum, allowing ice to change directly to vapor without passing through liquid. It involves freezing, primary drying to remove 98-99% water, and secondary drying to remove remaining bound water. Elutriation separates particles based on size, shape and density using an opposing gas or liquid stream, allowing finer particles to move upward while larger ones sediment downward.
3. LYOPHLIZATION
• Definition:
Lyophilization or freeze drying is a
process in which water is removed from a
product after it is frozen and placed under a
vacuum, allowing the ice to change directly
from solid to vapor without passing through a
liquid phase
4. PRINCIPLE OF LYOPHLIZATION
Lyophilization is based on a simple principle of physics
called “SUBLIMATION”. Sublimation is the process of
transition of a substance from solid to the vapor state
without passing through an intermediate liquid phase.
Lyophilization is performed at temperature and pressure
conditions below the triple point, to enable sublimation
of ice.
The entire process is performed at low temperature and
pressure by applying vacuum, hence it is good for
thermolabile compounds.
5. SIGNIFICANCE
To preserve the Biological activity of product.
To reduce the product weight so that transport cost can be reduced.
To extend the shelf life or stability.
To dry thermolabile materials.
To eliminate the need for refrigerated storage.
To get accurate, sterile dosing into the final product container.
7. FREEZING STAGE
Freezing of product solution to a temperature below its eutectic temperature.
Decrease the shelf temperature to -50ᵒc.
Low temperature and low atmospheric pressure is maintained.
Freons are used as refrigerant.
Formation of ice crystals occur.
The rate of ice crystallization define the freezing process and efficiency of
primary drying.
8. PRIMARY DRYING
Heat is introduced from shelf to the product under graded control by
electrical resistance coils or circulating silicon's.
The temperature and pressure should be below triple point of water i.e.,
0.0098 ᵒc and 4.58mmHg.
The driving force is vapor pressure difference between the evaporating
surface and condenser
Easily removes water up to 98% to 99%.
9. SECONDARY DRYING
The temperature is raised to 50 - 60ᵒc and vacuum is lowered about
50 mmHg.
Bound water is removed.
Rate of drying is low.
It takes about 10-20 hours.
10. PACKING
After drying the vacuum is replaced by filtered
dry air or nitrogen to maintain atmospheric
pressure.
Ampoules are sealed by either tip sealing or pull
sealing method.
Vials and bottles are sealed with rubber closures
and aluminum caps.
11. FACTORS AFEECTING
The factors affecting the process of lyophilization are the following:
Sample size.
Surface area.
Thickness.
Eutectic temperature.
Solute concentration.
Condenser temperature.
Vacuum.
12. APPLICATIONS
In pharmaceutical industry to increase shelf
life.
In food industry to preserve food and as an
essences.
In technical industries in chemical
synthesis and formation of stable products.
Flora and Fauna preservation.
14. ELUTRIATION
Definition:
Elutriation is a process for separating
particles based on their size, shape and
density, using a stream of gas or liquid
flowing in a direction usually opposite to the
direction of sedimentation.
15. EXPLANATION
In other words, small size particles will move
upward and large size particle will move downward.
So basically it is a process of separation of fine
particles from coarse particles.
The particle size can also be measured by this
process.
16. SIGNIFICANCE
It appears more attractive than decantation and also
has a certain practical advantages in that the
volume changes need no operator attention.
This allows a clear solution, or the filtrate to pass
through and flow out of the container.
17. TYPES OF ELUTRIATIONS
Gravitational Elutriation:
It is a type of elutriation in which the fluid particles move downwards due to
sedimentation (force of gravity) while the lighter particles remain upward.
Centrifugal Elutriation:
The one in which the fluid stream to rotate under high centrifugal force to suspend the
particles. These particle which are too large to rotate with direction of fluid, separates out on the
wall of elutriator. However, the fine particles move easily with the direction of fluid.
18. FACTORS AFFECTING ELUTRIATION
The factors affecting the process of elutriation are as following:
Velocity of fluid.
Particle size.
Position of particle.
Density of particle.