Did you know that you may patch your punctured tire instead of buying a new one? If you're willing to get a bit greasy and do the effort yourself, you'll be able to be back on the road and enjoy the drive-in in no time. Simply have a kit box with you at all times when driving. 5 Step-by-Step Process to Fix a Tire Puncture 1. Detect the Leak The first step is to identify the leak. The item that has punctured the tyre is not always easily discovered. Anything might be a nail or a sharp item. Examine the tire carefully to determine whether it has any holes or cuts. If a visual check is ineffective, inflate the tyre to the proper pressure level and listen for a hissing sound. If you can't find the puncture, combine some dish soap with water and spritz or brush the mixture on the tire. Bubbles will be visible coming from the leaking spot. Mark the location with tape. 2. Loosen the Lug Nuts and Jack up the Car The second step is to remove the tyre by losing the lug nuts. You may use an impact wrench or a lug wrench to do it. Do this before jacking up the automobile, otherwise, it will spin dangerously while removing the bolts. It's time to jack up the automobile and take the wheels off. You may accomplish that by parking your automobile on a solid or flat surface to keep it from rolling! To keep the automobile stable, use jack stands. Position your auto jack to your vehicle's designated jacking points and use it to elevate the side you're working on. 3. Remove the Lug Nuts and Thoroughly Clean the Hole Remove the lug nuts completely to detach the wheel from the wheelbase. It's now time to clean the leaking region by repeatedly putting the rasp tool into and out of the puncture/hole. 4. Connect the Plug To push a plug into a hole, it must be threaded into the center of the insertion tool. Lubricate the plug with an adhesive such as glue or rubber cement for a better seal and easier insertion. Now, let the plug alone for at least one minute to allow the glue to cure and dry. Remove the portion of the plug that protrudes from the tire surface. 5. Pump the Tire The next step is to fill the tire with the recommended air pressure to guarantee that your automobile moves smoothly. Replace the wheel, remove the floor jack, and tighten the lugs to the correct torque. However, if you are not confident about changing a flat tire, you can visit the nearest mechanic shop Careem Autocare. Here you can all types of tire services in Mississauga.

2. Did you know that a tire puncture may
frequently be fixed rather than replaced? If you're
ready to get a little greasy and put in the work, you'll be
back on the road and enjoying the drive-in in no time.
Always keep a kit box in your car.

3. 5 Step-by-Step Process to Fix a Tire
Puncture

4. Detect the Leak
The first step is to determine where the leak is originating
from. A tire rupture does not always have an obvious
reason. Anything might be a nail or a sharp item. Examine
the tire thoroughly to see whether it has any holes or cuts.
If the visual inspection fails, inflate the tyre to the correct
pressure and listen for a hissing sound. If you can't
discover the puncture, use a dish soap and water solution
to spray or brush the tire. Bubbles will form at the site of
the leak. Using tape, mark the place.

5. Loosen the Lug Nuts and Jack up the Car
The tire is then removed by unscrewing the lug nuts. You
may do it using an impact wrench or a lug wrench. If you
don't do this before jacking up the car, the nuts will spin
dangerously when you try to remove them.
It's time to jack up the car and remove the wheels. Parking
your vehicle on a hard or flat surface prevents it from
rolling! Use jack stands to keep the automobile steady.
Place your auto jack in the appropriate jacking locations
and raise the side you're working on.

6. Remove the Lug Nuts and Thoroughly
Clean the Hole
To disconnect the wheel from the wheelbase, totally remove
the lug nuts. It's now time to clean the leaking area by
repeatedly inserting and removing the rasp tool from the
puncture/hole.

7. Connect the Plug
Insert the plug into a hole by threading it through the centre
of the insertion tool. For a better seal and simpler
insertion, lubricate the plug using an adhesive such as glue
or rubber cement. Allow the adhesive to set for at least one
minute before inserting the plug. Remove the protruding
section of the plug from the tyre surface.

8. Pump the Tire
The next step is to adequately inflate the tyre so that your car
travels smoothly. After removing the floor jack, replace the
wheel and tighten the lugs to the desired torque.
However, if you are not confident about changing a flat
tire, you can visit the nearest mechanic shop Careem
Autocare. Here you can all types of tire services in
Mississauga.

9. Contact Us
 Address: C4 - 1115 crestlawn Dr Mississauga, ON . L4W 1A7
 Phone: (289) 497-9996 | (416) 477-3621 |
(647) 716-3440
 Email: careemautocare@gmail.com