Balboa flashing light errors
•
0 likes•2,726 views
The document describes error codes for a Balboa spa indicated by flashing lights. A light flashing on once per second and off for one second means overheat protection is engaged. A light flashing on once per second but off for longer indicates a flow switch error. A light flashing off once per second but on for longer means an open sensor error. The document provides contact information for technical support.
Report
Share
Report
Share
Download to read offline
Recommended
Standard spaside instruction sheet
The document provides instructions for operating various functions of a spa or hot tub. It describes the economy mode which maintains water temperature 20°F below the set point. It also describes the freeze protection mode which activates the pump and heater if water drops below certain temperatures. Default settings are described such as filtration cycles running for 1 hour every 24 hours with water at 95°F. Instructions are provided for operating pumps, blowers, lights and setting the temperature. Error codes and troubleshooting tips are also summarized.
53883 0420 gl2_gl2001m3_rca-30
This document provides technical specifications for the Balboa Instruments GL2001 Mach 3 spa control system. It includes the system model number, software version, and component part numbers. Wiring diagrams and descriptions of features such as power requirements, control panel options, and dip switch settings are also provided.
Balboa manualtroubleshootingandservice reva
The document provides information on troubleshooting and servicing Balboa spa and electrical equipment. It describes Balboa's patented M7 technology which uses two sensors to determine water flow and temperature without external switches. It also outlines how to check wiring, voltage, panels, boards, heaters and more when servicing spa systems. Procedures for replacing parts and diagnosing issues are provided.
Ultimate spaside instruction sheet
This document provides instructions for adjusting various settings on a spa control panel, including temperature unit (F or C), time of day, economy mode start time and duration, panel lock, and descriptions of default settings and modes like economy mode and freeze protection. Settings are adjusted using the program, list, enter and up/down arrow keys, and confirmed with enter. Error codes are displayed as flashing dots and require servicing.
Ps 9704 manual-rev1_2
This document provides installation and operation instructions for a PS-9704 series pool/spa control system. It includes guidelines for installing remote heaters, making electrical and wet connections, programming filtration settings, and troubleshooting. Safety precautions are outlined, and a wiring diagram and parts list are provided.
Ps 7100 manual-rev1_2
The document provides installation and operation instructions for a Platinum Series pool and spa control system. It includes details on installing remote heaters, electrical connections, temperature sensors, equipment connections, and programming filtration settings. Safety instructions are provided at the beginning regarding proper installation and use of the system.
Ps 6500 manual-rev1_2
The document provides installation instructions for PS-6502 & PS-6503 Platinum Series pool and spa control systems. It describes how to install the heater in different locations including on the bottom, back, or top of the control box using adjustable clamps or slide brackets. The instructions also cover electrical installation, temperature sensor placement, equipment connections, and programming filtration settings. Additional sections provide details on optional equipment, operational considerations, troubleshooting, and warranty information.
Hq label wd highlight
This website sells wholesale pool and spa parts. It is located at http://www.MyPoolSpas.com. The phone number for My Pool and Spas is 920-925-3094.
Recommended
Standard spaside instruction sheet
The document provides instructions for operating various functions of a spa or hot tub. It describes the economy mode which maintains water temperature 20°F below the set point. It also describes the freeze protection mode which activates the pump and heater if water drops below certain temperatures. Default settings are described such as filtration cycles running for 1 hour every 24 hours with water at 95°F. Instructions are provided for operating pumps, blowers, lights and setting the temperature. Error codes and troubleshooting tips are also summarized.
53883 0420 gl2_gl2001m3_rca-30
This document provides technical specifications for the Balboa Instruments GL2001 Mach 3 spa control system. It includes the system model number, software version, and component part numbers. Wiring diagrams and descriptions of features such as power requirements, control panel options, and dip switch settings are also provided.
Balboa manualtroubleshootingandservice reva
The document provides information on troubleshooting and servicing Balboa spa and electrical equipment. It describes Balboa's patented M7 technology which uses two sensors to determine water flow and temperature without external switches. It also outlines how to check wiring, voltage, panels, boards, heaters and more when servicing spa systems. Procedures for replacing parts and diagnosing issues are provided.
Ultimate spaside instruction sheet
This document provides instructions for adjusting various settings on a spa control panel, including temperature unit (F or C), time of day, economy mode start time and duration, panel lock, and descriptions of default settings and modes like economy mode and freeze protection. Settings are adjusted using the program, list, enter and up/down arrow keys, and confirmed with enter. Error codes are displayed as flashing dots and require servicing.
Ps 9704 manual-rev1_2
This document provides installation and operation instructions for a PS-9704 series pool/spa control system. It includes guidelines for installing remote heaters, making electrical and wet connections, programming filtration settings, and troubleshooting. Safety precautions are outlined, and a wiring diagram and parts list are provided.
Ps 7100 manual-rev1_2
The document provides installation and operation instructions for a Platinum Series pool and spa control system. It includes details on installing remote heaters, electrical connections, temperature sensors, equipment connections, and programming filtration settings. Safety instructions are provided at the beginning regarding proper installation and use of the system.
Ps 6500 manual-rev1_2
The document provides installation instructions for PS-6502 & PS-6503 Platinum Series pool and spa control systems. It describes how to install the heater in different locations including on the bottom, back, or top of the control box using adjustable clamps or slide brackets. The instructions also cover electrical installation, temperature sensor placement, equipment connections, and programming filtration settings. Additional sections provide details on optional equipment, operational considerations, troubleshooting, and warranty information.
Hq label wd highlight
This website sells wholesale pool and spa parts. It is located at http://www.MyPoolSpas.com. The phone number for My Pool and Spas is 920-925-3094.
Eco 3 spaside instruction sheet
The document provides information on the default system operation, freeze protection modes, high temperature error handling, filtration cycles, pump and blower controls, light controls, temperature setting, and error identification for a spa or pool system. When power is applied, the system will initiate a default 24-hour filtration cycle at 95°F. It describes two modes of freeze protection below 59°F and 49°F and will suspend filtration if temperatures exceed 115°F or reach errors.
Eco 2 spaside instruction sheet
The document provides instructions for operating and programming a spa, including:
- If the water temperature exceeds 115°F, the heater will turn off, and above 122°F all outputs will disable until cooled.
- The filtration cycle can be programmed to run 1, 2, or 3 times daily for 60, 120, 180, or 480 minutes each cycle.
- By default, the spa will filter for 1 hour every 24 hours, maintaining the temperature at 95°F.
- Instructions are provided for operating the pump, accessory, light, and adjusting the temperature settings.
- The system enters a freeze protection mode if the temperature drops below 59°F by turning the pump on periodically.
Eco 1 spaside instruction sheet
The document provides instructions for operating and programming a spa control system. It describes how the system handles high temperatures, allows setting filter cycles for 1-3 times daily and durations of 60-180 minutes, and will default to a 24-hour filter cycle at 95°F if power is lost. It also explains how to operate the pump, light, and change the temperature setting, and describes freeze protection and error identification features.
Eco 2 pcb revisions
This document summarizes the revision history of PCB part number 33-0024-Rx from the initial R0 revision in January 1999 through the current R6 revision. It describes the changes made at each revision level such as PCB layout changes, software changes, additions of memory and removal of features. It also provides information to help identify the correct wiring diagram for a given revision level.
Eco 1 programming
This document provides instructions for an Eco 1 timed filtration system. It states to press and hold the light button to change the duration of filtration, and to press and hold the pump button to change the number of times filtration will occur. It also provides contact information for My Pool and Spas, a wholesale pool and spa parts supplier.
Deluxe spaside instruction sheet
The document provides instructions for setting various operating parameters of a pool or spa control system including time, filtration start/duration, temperature display units, panel lock, economy mode, freeze protection, and error conditions. It describes pressing the program key to access each setting and using up/down arrows to adjust before pressing program to save. It also lists default settings if power is lost.
Cs9700 software upgrade notice 3 07
The changes include:
- Two programmable filtration cycles, one for AM and one for PM.
- A new "Smart Summer Mode" that operates pumps and chlorinators during cooler times when temperatures exceed a threshold.
- Optional programming via Palm Pilot or keypad.
- New auxiliary circuit and circulation pump options.
- Updated owner's manuals to reflect changes.
Cs9700 llp settings 3 07
This document provides contact information for a wholesale pool and spa parts business called MyPoolSpas.com. It lists their phone number as 920-925-3094. The business sells wholesale pool and spa parts.
Control cord colors
This document provides contact information for a company called MyPoolSpas.com Spa Parts Wholesale Pool. They sell pool and spa parts and can be reached by calling 920-925-3094. The document lists the name of the company and their phone number.
9400 9600 programming
The document provides instructions for programming various settings on an HT-2 / 9600 Series spa control system, including time of day, filtration cycle start time and duration, economy mode start time and duration, temperature units (Fahrenheit or Celsius), and a spa-side lock feature. It also describes low level programming options that can be changed by positioning jumpers on the system board, including pump, blower, light, ozone, fiber optics, clock, current, circulation pump, and sensor calibration settings.
9300 programming
The document discusses four jumpers on a system board that can be positioned to change parameters of an equipment system. Jumper 1 sets either a high or low current limit. Jumper 2 selects whether temperature is displayed in Fahrenheit or Celsius. Jumpers 3 and 4 determine if the pumps run as single or two speed pumps. Positioning the jumpers allows customizing the system's operation based on electrical specifications and pump configuration.
85 0138 infrared remote-web
This document provides instructions for operating an infrared remote control for a pool or spa. It includes:
1. A key chart explaining the functions of each button on the remote control.
2. Instructions for programming the remote to control up to three home entertainment or automation devices by entering their unique four-digit codes.
3. Procedures for replacing batteries, searching for codes if a device is not responding, checking stored codes, and putting the remote into learning mode to add new functions from an original remote control.
85 0137 rev 1-palm pilot programming_web
The document provides instructions for programming a Palm Pilot PDA to communicate with and adjust the low-level programming of Hydro-Quip control systems. The PDA must have the Serve-Soft 2 software installed and unlocked using the username "Hydro-Quip" and password "Hq92u1". An ADIR-1 cartridge is used to connect the PDA to the control system. Low-level parameters can then be viewed and modified on the PDA screen by tapping selections. Additional features like current states, troubleshooting, and documentation can also be accessed.
85 0136 spaside cutout template
This document provides a template for installing spaside controls for pool and spa equipment. The template is only to be used with ECO-1, 2, 5, and 6 series controls and measures 2 5/8 inches by 2 5/8 inches with two 1 inch holes. Installers are directed to refer to the installation manual for details on installation.
85 0135 b-installation manual_web
This document provides instructions for installing an outdoor pool and spa system. It discusses:
- Having a qualified electrician install the electrical components according to code
- Connecting the system to a dedicated circuit protected by a GFCI
- Connecting components such as pumps, blowers, and lights to color-coded receptacles
- Configuring universal circuits for 120V or 240V operation
- Installing the control panel and temperature sensor
- Connecting a gas heater according to the manufacturer's instructions
- Bypassing pressure or flow switches if needed
- Adjusting the pressure switch if issues arise related to water flow
85 0135 a-rev 1_installation manual
The document provides installation instructions for a solid-state pool and spa control system. It outlines:
1) Electrical installation requirements including using a qualified electrician, proper sizing of circuits and conductors, and acceptable wiring configurations such as installing a GFCI at the main panel or in a subpanel.
2) Instructions for converting universal circuits to 120V or 240V as needed.
3) Details on installing spa-side controls, temperature sensors, lights, and starting up the system by following the provided operation manual.
85 0079 vds insert
The Visual Diagnostic System was designed by Hydro-Quip to offer simple on-site diagnosis for customers. It features lights that illuminate to indicate issues that can be identified by referencing the owner's manual. The system aims to help diagnose air switches, pumps, heat, filtration, and other components through easy-to-interpret light signals.
85 0076-e eco-2 plus-installation insert_web
This document provides contact information for a wholesale pool and spa parts business called MyPoolSpas.com, including their website URL and phone number. The business sells pool and spa parts wholesale and can be contacted at their website or by calling 920-925-3094.
85 0076-c 6220 troubleshooting
The document repeatedly lists the website http://www.MyPoolSpas.com and a phone number 920-925-3094. It can be summarized that this is a contact listing for a wholesale business called MyPoolSpas that sells pool and spa parts and their website and phone number are provided.
More Related Content
More from Accurate Pool & Spa Services, llc
Eco 3 spaside instruction sheet
The document provides information on the default system operation, freeze protection modes, high temperature error handling, filtration cycles, pump and blower controls, light controls, temperature setting, and error identification for a spa or pool system. When power is applied, the system will initiate a default 24-hour filtration cycle at 95°F. It describes two modes of freeze protection below 59°F and 49°F and will suspend filtration if temperatures exceed 115°F or reach errors.
Eco 2 spaside instruction sheet
The document provides instructions for operating and programming a spa, including:
- If the water temperature exceeds 115°F, the heater will turn off, and above 122°F all outputs will disable until cooled.
- The filtration cycle can be programmed to run 1, 2, or 3 times daily for 60, 120, 180, or 480 minutes each cycle.
- By default, the spa will filter for 1 hour every 24 hours, maintaining the temperature at 95°F.
- Instructions are provided for operating the pump, accessory, light, and adjusting the temperature settings.
- The system enters a freeze protection mode if the temperature drops below 59°F by turning the pump on periodically.
Eco 1 spaside instruction sheet
The document provides instructions for operating and programming a spa control system. It describes how the system handles high temperatures, allows setting filter cycles for 1-3 times daily and durations of 60-180 minutes, and will default to a 24-hour filter cycle at 95°F if power is lost. It also explains how to operate the pump, light, and change the temperature setting, and describes freeze protection and error identification features.
Eco 2 pcb revisions
This document summarizes the revision history of PCB part number 33-0024-Rx from the initial R0 revision in January 1999 through the current R6 revision. It describes the changes made at each revision level such as PCB layout changes, software changes, additions of memory and removal of features. It also provides information to help identify the correct wiring diagram for a given revision level.
Eco 1 programming
This document provides instructions for an Eco 1 timed filtration system. It states to press and hold the light button to change the duration of filtration, and to press and hold the pump button to change the number of times filtration will occur. It also provides contact information for My Pool and Spas, a wholesale pool and spa parts supplier.
Deluxe spaside instruction sheet
The document provides instructions for setting various operating parameters of a pool or spa control system including time, filtration start/duration, temperature display units, panel lock, economy mode, freeze protection, and error conditions. It describes pressing the program key to access each setting and using up/down arrows to adjust before pressing program to save. It also lists default settings if power is lost.
Cs9700 software upgrade notice 3 07
The changes include:
- Two programmable filtration cycles, one for AM and one for PM.
- A new "Smart Summer Mode" that operates pumps and chlorinators during cooler times when temperatures exceed a threshold.
- Optional programming via Palm Pilot or keypad.
- New auxiliary circuit and circulation pump options.
- Updated owner's manuals to reflect changes.
Cs9700 llp settings 3 07
This document provides contact information for a wholesale pool and spa parts business called MyPoolSpas.com. It lists their phone number as 920-925-3094. The business sells wholesale pool and spa parts.
Control cord colors
This document provides contact information for a company called MyPoolSpas.com Spa Parts Wholesale Pool. They sell pool and spa parts and can be reached by calling 920-925-3094. The document lists the name of the company and their phone number.
9400 9600 programming
The document provides instructions for programming various settings on an HT-2 / 9600 Series spa control system, including time of day, filtration cycle start time and duration, economy mode start time and duration, temperature units (Fahrenheit or Celsius), and a spa-side lock feature. It also describes low level programming options that can be changed by positioning jumpers on the system board, including pump, blower, light, ozone, fiber optics, clock, current, circulation pump, and sensor calibration settings.
9300 programming
The document discusses four jumpers on a system board that can be positioned to change parameters of an equipment system. Jumper 1 sets either a high or low current limit. Jumper 2 selects whether temperature is displayed in Fahrenheit or Celsius. Jumpers 3 and 4 determine if the pumps run as single or two speed pumps. Positioning the jumpers allows customizing the system's operation based on electrical specifications and pump configuration.
85 0138 infrared remote-web
This document provides instructions for operating an infrared remote control for a pool or spa. It includes:
1. A key chart explaining the functions of each button on the remote control.
2. Instructions for programming the remote to control up to three home entertainment or automation devices by entering their unique four-digit codes.
3. Procedures for replacing batteries, searching for codes if a device is not responding, checking stored codes, and putting the remote into learning mode to add new functions from an original remote control.
85 0137 rev 1-palm pilot programming_web
The document provides instructions for programming a Palm Pilot PDA to communicate with and adjust the low-level programming of Hydro-Quip control systems. The PDA must have the Serve-Soft 2 software installed and unlocked using the username "Hydro-Quip" and password "Hq92u1". An ADIR-1 cartridge is used to connect the PDA to the control system. Low-level parameters can then be viewed and modified on the PDA screen by tapping selections. Additional features like current states, troubleshooting, and documentation can also be accessed.
85 0136 spaside cutout template
This document provides a template for installing spaside controls for pool and spa equipment. The template is only to be used with ECO-1, 2, 5, and 6 series controls and measures 2 5/8 inches by 2 5/8 inches with two 1 inch holes. Installers are directed to refer to the installation manual for details on installation.
85 0135 b-installation manual_web
This document provides instructions for installing an outdoor pool and spa system. It discusses:
- Having a qualified electrician install the electrical components according to code
- Connecting the system to a dedicated circuit protected by a GFCI
- Connecting components such as pumps, blowers, and lights to color-coded receptacles
- Configuring universal circuits for 120V or 240V operation
- Installing the control panel and temperature sensor
- Connecting a gas heater according to the manufacturer's instructions
- Bypassing pressure or flow switches if needed
- Adjusting the pressure switch if issues arise related to water flow
85 0135 a-rev 1_installation manual
The document provides installation instructions for a solid-state pool and spa control system. It outlines:
1) Electrical installation requirements including using a qualified electrician, proper sizing of circuits and conductors, and acceptable wiring configurations such as installing a GFCI at the main panel or in a subpanel.
2) Instructions for converting universal circuits to 120V or 240V as needed.
3) Details on installing spa-side controls, temperature sensors, lights, and starting up the system by following the provided operation manual.
85 0079 vds insert
The Visual Diagnostic System was designed by Hydro-Quip to offer simple on-site diagnosis for customers. It features lights that illuminate to indicate issues that can be identified by referencing the owner's manual. The system aims to help diagnose air switches, pumps, heat, filtration, and other components through easy-to-interpret light signals.
85 0076-e eco-2 plus-installation insert_web
This document provides contact information for a wholesale pool and spa parts business called MyPoolSpas.com, including their website URL and phone number. The business sells pool and spa parts wholesale and can be contacted at their website or by calling 920-925-3094.
85 0076-c 6220 troubleshooting
The document repeatedly lists the website http://www.MyPoolSpas.com and a phone number 920-925-3094. It can be summarized that this is a contact listing for a wholesale business called MyPoolSpas that sells pool and spa parts and their website and phone number are provided.
More from Accurate Pool & Spa Services, llc (20)
Balboa flashing light errors
- 1. Balboa, Error Code, Flashing Lights Details: Overheat Protection‐ Light Flashes ON once per second and Off for one second Flow Switch Error‐ Light Flashes On once per second (off more than on) Open Sensor‐ Light Flashes OFF once per second (On more than off) http://www.MyPoolSpas.com and Spa Parts 920-925-3094 Wholesale Pool