Renewable energy market analysis the gcc region, RENEWABLE ENERGY MARKET ANA...
Micro Wind Turbines for Domestic Application
1.
Micro-‐Wind
Turbines
for
Domestic
Application
Student: Paul McEvoy (C10356573)
Course: DT005/3 Building Services Engineering
Date: 7th-‐‑December-‐‑2012
2. Micro-Wind Turbines for Domestic Application
December 2012
1
Abstract
The generation of electricity from renewable sources of energy will be a key part in the
development of future strategies for many countries. This topic is very important for Ireland
mainly because of its lack of fossil fuel resources. The possibility of producing vast amounts
of electricity exist here in Ireland due to its geographic position. Large scale wind electricity
generation reached 1264 MW of installed capacity by January 2010. However small scaled
wind generation has not been hugely popular to date. The unclear economics of micro-wind
turbines under Irish conditions is considered the biggest obstacle for expanding micro-wind
turbine installation. This study will inform the reader that micro-wind turbines are a viable
option here in Ireland once the appropriate conditions are met.
3. Micro-Wind Turbines for Domestic Application
December 2012
2
Table
of
Contents
Abstract......................................................................................................................................1
List of Figures............................................................................................................................4
Dissertation Declaration.............................................................................................................5
Acknowledgements....................................................................................................................6
Introduction................................................................................................................................7
Background ............................................................................................................................7
Motivation..............................................................................................................................7
Personal ..............................................................................................................................7
Energy Policy .....................................................................................................................8
Market.................................................................................................................................9
Information.........................................................................................................................9
Objectives...............................................................................................................................9
Thesis Layout.......................................................................................................................10
Ireland’s Energy Requirements................................................................................................11
Current Status.......................................................................................................................11
Ireland’s Future Targets .......................................................................................................13
Drivers for Deployment of Renewable Energy Technologies in Ireland.............................14
Wind energy in Ireland ............................................................................................................15
Geographical Positioning .....................................................................................................15
Wind Speeds in Ireland ........................................................................................................16
The Operation of a micro-wind turbine ...................................................................................22
Micro-Generation.................................................................................................................22
History..................................................................................................................................22
How does it work?................................................................................................................23
Site Selection........................................................................................................................25
Wind speed .......................................................................................................................25
Wind Obstacles.................................................................................................................25
Topography.......................................................................................................................25
Planning Permission .........................................................................................................25
Technology ..............................................................................................................................26
Smart Meters ........................................................................................................................26
4. Micro-Wind Turbines for Domestic Application
December 2012
3
An introduction to Smart Meters......................................................................................26
How do Smart Meters work?............................................................................................26
The current Smart Meter situation in Ireland ...................................................................27
Grid Connection ...................................................................................................................28
Basic Grid Connection......................................................................................................28
Advanced Grid Connection ..............................................................................................28
Off-Grid Connection.........................................................................................................29
Hybrid Sources of Input ...................................................................................................29
Installation and Operation ................................................................................................29
Current Standards and Regulations for Connecting a Micro-Generator in Ireland..........30
The current micro-wind turbine situation in Ireland................................................................31
The current micro-wind turbine market ...............................................................................31
Micro-wind turbines available on the Irish Market..............................................................32
The current legislation and regulations for installing a micro-wind turbine in Ireland .......35
The Current financial support for exporting electricity generated from micro-wind turbines
..............................................................................................................................................36
Case Studies.............................................................................................................................37
Case Study 1: Householder’s Micro-Wind Turbine Project ................................................37
Case Study 2: Householder’s Micro-Wind Turbine Project ................................................42
Conclusions..............................................................................................................................50
Conclusions..........................................................................................................................50
Recommendations ................................................................................................................50
References................................................................................................................................51
5. Micro-Wind Turbines for Domestic Application
December 2012
4
List
of
Figures
Figure 1: Total final consumption by fuel 1990-2010 (SEAI 2011) .......................................12
Figure 2: European wind Atlas, Onshore (Wind-Energy 2012) ..............................................15
Figure 4: Micro-Wind Turbine Components (Government 2012) ..........................................23
Figure 5: Electrical output of a Turbine. (EAI 2012) ..............................................................24
Figure 6: How a Micro-Wind Turbine work in a home. (trust 2012)......................................24
Figure 7: Breakdown of grid connected micro renewable electrical generation devices
installed from January 2007 to February 2010 in Ireland. (Li et al. 2012) ......................31
Figure 8: Market share by installation. (SEAI 2010)...............................................................32
Figure 9: Kingspan KW6. (Beco, 2012) ..................................................................................33
Figure 10: KW6 showing power production against wind velocities (m/s) ............................33
Figure 11: C&F Green Energy CF6e. (C&F-GreenEnergy, 2012)..........................................34
Figure 12: CF6e showing power production (kW) against wind velocities (m/s)...................34
Figure 13: 6kW Proven (caredelyn.co.uk)...............................................................................38
Figure 14: 2.5kW Proven.........................................................................................................43
Figure 15: Concrete base to support 11 metre high mast.........................................................44
6. Micro-Wind Turbines for Domestic Application
December 2012
5
Dissertation Declaration
I hereby declare that this dissertation is my own work and effort and it has not been
previously submitted to any other third level institution. Sources of information that have
been used in this dissertation have been acknowledged.
Signature: …………………………
Date: ………………………………
7. Micro-Wind Turbines for Domestic Application
December 2012
6
Acknowledgements
This dissertation would not have been possible without the guidance and the help of several
individuals who in one way or another contributed and extended their valuable assistance in
the preparation and completion of this study.
First of all the author would like to thank his family and friends for their kind support during
the writing of this dissertation. The author would also like to show his appreciation to Ciara
Ahern for her help each week providing knowledgeable information which went a long way
towards the completion of this dissertation. Finally the author would like to thank Mr Patsy
Smith, a micro-wind turbine owner from Gowna, Co. Cavan who allowed the author to use
his micro-wind turbine as part of his case study, and Mr Michael Reilly of M&C Hybrid
Energy Ltd, an MCS certified installer, who installed Mr Smith’s micro-wind turbine and
kindly answered any queries the author had.
8. Micro-Wind Turbines for Domestic Application
December 2012
7
Introduction
Background
The use of renewable energy has become increasingly popular in recent years. The factors
responsible for this are that countries now need to become less reliant on non-renewable
fossil fuels such as oil and coal and make more use of renewable sources such as solar and
wind. Another factor influencing the interest in renewable energy is the international
agreement to make efforts in order to reduce the amount of green-house gases in the earth’s
atmosphere. As a result of this interest in renewable energy, governments in many countries
are promoting energy generation in order to reduce carbon dioxide emissions which evolve
from fossil fuels. The utilisation of renewable sources of energy is even more important for
Ireland due to its lack of fossil fuel resources. Peat is the only indigenous fossil fuel available
in Ireland.
The use of wind power is recognised as one of the fastest growing industries in the area of
renewable energy. Annual installations of wind power have increased over the last seventeen
years from 814 MW in 1995 to 9,616 MW in 2011, an annual average growth of 15.6%. It is
expected that more than 100,000 MW of wind power will be installed in Europe alone by the
year 2030. Ireland has amazing resources for the use of renewable energy and in particular,
wind energy. The wind energy resource in Ireland is four times that of the European
average.(Li, Boyle and Reynolds 2012) This unlimited amount of wind gives Ireland the
opportunity to generate electricity by means of wind energy.
The site of wind turbines located on mountains and stretching into the sea in recent years has
become quite common. But now we are beginning to see smaller scale wind turbines attached
or integrated in some way onto buildings. These are called micro-wind turbines. This is an
area of renewable energy which has great potential for innovation, expansion and integration.
Whether this potential is realised depends on the costs of manufacture, installation and
maintenance in both retrofit and new buildings.
Motivation
Personal
The decision to do a study on this topic was due to its relevance to the fast changing world in
which we live in today. Due to growing concerns about the future availability of fossil fuels
and the effects this will have on electricity prices, it is important that we gear more towards
alternative ways of producing electricity such as ‘Micro-Wind Turbines’.
9. Micro-Wind Turbines for Domestic Application
December 2012
8
Energy Policy
Competitiveness of energy supply
Ireland can be seen as a fully sustainable, secure, efficient, affordable and competitive all
island energy market. Having a reliable and competitively priced energy supply in Ireland, in
the future will have a major effect on the country’s competitiveness and economic growth.
Structural change within the energy market is also required in order to enable competition
and deliver consumer choice. (Government white paper 2006) The creation of the Single
Electricity Market in 2007 has created a more competitive market. It has kept electricity
prices competitive, ensured security of supply, and provided environmental
benefits.(Regulation 2011) The introduction to the electricity market mechanism has been a
big motivator to use micro-generation technology.
Environmental sustainability
Between the years 1990 and 2007, the total annual energy requirement grew in absolute terms
by 69.8%, in which 56% of this was taken up by oil. (Government and Irish 2012) In Ireland
by 2020 the planned level of deployment of renewable energy will help to ensure that
Ireland’s energy supply will be more diverse, secure and sustainable. The 2020 vision of
renewable energy consultation under taken with Northern Ireland proposes the integration of
renewable energy with in an all-island energy market.(Government white paper 2006)
The motives behind using Micro-Wind Turbines include the following:
1. The need to reduce energy related green-house gas emissions.
2. Government incentives for developing alternative means of energy sources.
3. Reducing the demand by strengthening energy efficiency and conservation measures.
Ensuring security of supply
While competitiveness of energy supply and environmental sustainability are both key,
ensuring the security of supply is imperative. One of the main objectives of the Irish energy
policy is to ensure that affordable energy is constantly available with no risk of the supply
being disrupted. Although measures have been put in place to ensure security of supply such
as mandatory oil storage, there is still a lack of significant natural resources which creates a
major challenge for the future.(Unions 2007) However, with the use of Micro-Wind
Turbines, a natural resource is created. A larger amount of Micro-Wind Turbines would
contribute to the delivery of electricity to homes and businesses over networks that are
adequate and secure while creating an attractive environment to encourage investments in
energy infrastructure. (Purcell 2008)
10. Micro-Wind Turbines for Domestic Application
December 2012
9
Market
It is clear that there is a gap in the electricity market for renewable energies. An obvious
interest in Micro-Wind Turbines would become apparent if suppliers could manufacture the
device at an affordable price for consumers and ensure them that the device is capable of
generating electricity. In recent years, people have become aware of how their actions are
affecting our climate. They are beginning to make the effort to help with climate change. By
installing a Micro-Wind Turbine in their own domestic home or commercial business, this
gives them the chance to help with climate change while saving money on their electricity
bill at the same time.
Information
There are many people out there who are unsure and unaware in some cases of Micro
generation technologies and in this case Micro-Wind Turbines. Since the public are the target
market for this relatively new technology, I feel that it is important that they understand the
use of this device and what it is capable of producing. In many cases when a new technology
is unleashed, it can be misunderstood, therefore becoming unpopular as a result of poor
public opinion. If Micro-Wind Turbines do not impress the public with their positive effects
then micro wind technology will be a flash in the plan and could end up being perceived as a
great chance wasted in the future.(Purcell 2008)
Objectives
Through-out this dissertation, information will be giving about micro-wind turbines that may
interest people into considering or maybe even installing this latest piece of technology as a
secondary source of electricity supply on their own existing buildings, whether they are
domestic or commercial. In order to do this, the merits of a micro-wind turbine installation
will be displayed in a clear and organised manner. This dissertation will uncover the
capabilities of a micro-wind turbine by carrying out the following tasks to the best of my
ability:
1. Give a clear in depth description of a micro-wind turbine.
2. Carry out a case study on an existing turbine in operation in conjunction with a
commercial building in Ireland.
3. Carry out a case study on an existing turbine in operation in conjunction with a
domestic building in Ireland.
4. Calculate the total cost of installing this piece of technology and work out the
simple pay-back period.
11. Micro-Wind Turbines for Domestic Application
December 2012
10
Thesis Layout
This dissertation will be laid out in the most organised way possible in order to enhance the
reader and also make it easier to locate specific pieces of information. A dissertation
declaration will be the first chapter followed by acknowledgements. Chapter two gives an
introduction which comprises of the background, Motivation (Personal, Energy policy,
Markets, Information), and the objectives of this thesis. The following chapter is on Ireland’s
energy requirements with a detailed account on its current status, future targets and drivers
for renewable energy technologies. Chapter three is about wind energy in Ireland with
calculated average wind speeds through-out Ireland over the past three years. The next
chapter gives details on micro-generation with a description on the basic operation of a
micro-wind turbine while in chapter five the present technology available for this application
will be explained in terms of metering and grid connections. Chapter six gives details on the
current micro-wind turbine situation in Ireland including, the current market, turbines
available on the current Irish market, Irish regulations and legislations for installing micro-
wind turbines, and financial support giving for exporting electricity that is produced from a
micro-wind turbine. In chapter seven a case study on a householder’s micro-wind turbine
project in the UK will be carried and in the same chapter a case study on a householder’s
micro-wind turbine project here in Ireland will be also carried out. The conclusion of this
study will follow this chapter and it will include any interesting findings and present any
recommendations as a result of these findings. The appendix will be the final chapter to my
dissertation and it will comprise references which I found useful during the writhing of this
dissertation.
12. Micro-Wind Turbines for Domestic Application
December 2012
11
Ireland’s
Energy
Requirements
Current Status
Ireland’s energy is primarily consumed by electricity generation, transportation and heat
generation. In order for Ireland to meet these energy requirements, we have become heavily
dependent on fossil fuel imports. Irelands import dependence reached 86% in 2010, down
from the peak 91% in 2006. (SEAI 2011) Peat is Ireland’s only indigenous fuel source; all
other fossil fuel sources are imported. (Rourke, Boyle and Reynolds 2009) Ireland’s energy
consumption has rapidly increased since the early 1990’s, however it is gradually reducing as
you can see from the 5% drop from 2006 to 2010.
Energy consumption in Ireland reached 12.046 mtoe in 2010, with fossil fuels accounting for
95% of the total energy consumed. (SEAI 2011) The largest energy consumption sector
within Ireland is the transport sector with a share of 38.8% of the final energy consumption.
This is followed by thermal uses (i.e. space heating, cooking etc) with residential and
industrial sectors having shares of 27.1% and 17.3% respectively, and finally services and
agricultural sectors are the remaining two energy consumption sectors with shares of 14.4%
and 2.27%. The consumption of energy in the transport sector has decreased from 41.5% in
2006 to 38.8% in 2010. (SEAI 2011) This decrease may be due to the recent hike in fuel
prices.
Electricity generation totalled 4925 ktoe, accounting for 33% of the primary energy
consumption in Ireland in 2010. Natural gas was the dominant fuel responsible for 61% of the
total primary input to electricity generation followed by coal, accounting for 18% of the fuel
mix. In 2010, renweables accounted for 7.5% of the energy inputs to generate electricity with
wind energy contributing to 5%. Wind generation fell by 4.6% in 2010. The services sector
was the largest sector to use electricity, using 36% of the total in 2010. This was followed by
the residential (34%), industry (27%) and the agricultural sector with (2.2%). There was an
increase of 3.2% to energy inputs to electricity generation, while at the same time the final
consumption of electricity increased by 0.8%, resulting in an overall decrease in efficiency.
(SEAI 2011) This statistic tells us that we need to make more use of renewable sources out
there in order to reduce the high demand for fuel sources needed to generate electricity.
13. Micro-Wind Turbines for Domestic Application
December 2012
12
Figure
1:
Total
final
consumption
by
fuel
1990-‐2010
(SEAI
2011)
The chart above illustrates the final consumption of each fuel over the period 1990 – 2010. In
2010 natural gas experienced an increase in consumption with a growth of 9.1% in
comparison to 7.1% in 2006. This growth in the use of natural gas is a result of the increased
amount of space heating requirements in buildings as a result of two very cold spells at the
beginning and end of the year. Gas is now being used to generate electricity, replacing all
other fuel types that done so in the past. Also its increased use in the industrial and residential
sectors may be relevant reasons as to why the use of natural gas has grown. In 2010, the final
consumption of oil fell by 3.3% and its share of the final energy consumption fell to 61%,
down from 62% in 2009. The final energy consumption share of cool was 11.6% in 1990.
This dropped dramatically to 2.9% in 2010 displaying an evident decrease in the use of cool.
Peat consumption has decreased from 10.4% in 1990 to 2.1% in 2010.The use of renewable
energy technologies increased by 11% in 2010. (SEAI 2011) The majority of the growth in
the use of renewable energy technologies in Ireland was achieved in the residential sector,
and with the use of wind energy to generate electricity.
14. Micro-Wind Turbines for Domestic Application
December 2012
13
Ireland’s Future Targets
The Department of Communications, Marine and Natural Resources published an Irish
government energy white paper on the 12th
of March 2007 entitled Delivering a Sustainable
Energy Future for Ireland. The white paper highlights the goals that will deliver a sustainable
energy future for Ireland. The paper is driven primarily by the challenge of a secure energy
supply and the prevention of climate change. (Rourke et al. 2009) The Irish governments
energy action plans for 2020 are set out in the energy white paper.
The white paper includes:
• Actions being put in place in order to ensure security of energy supply.
• Actions to promote the sustainability of energy supply and use.
• Actions to enhance the competitiveness of energy supply.
(Government white paper 2006)
The energy market in Ireland can be separated into the following three divisions:
1. Electricity generation
2. Thermal energy
3. Transportation
The following targets were set with regard to renewable energy:
• 15% of Ireland’s electricity consumption will be generated from renewable sources by
2010, and 33% generated from renewable sources by 2020.
• 500 MW of ocean energy capacity and 800 MW of Combined Heat and Power (CHP)
with an emphasis on biomass will be installed by 2020.
• 30% biomass co-fired at the state owned peat power plants by 2015.
(Government white paper 2006)
In terms of environmental targets, the National Climate Change Strategy 2007-2012 was
published by the Department of the Environment, Heritage and Local Government on the 2nd
of October 2007 setting out measures by which Ireland will meet its Kyoto Protocol 2008 –
2012 commitment, and also setting out measures for the post Kyoto period. The report
estimates an annual emissions reduction of 1.47 million tonnes of CO2 will be achieved with
the target of 15% renewable electricity by 2010, and an annual emissions reduction of 3.26
million tonnes with 33% renewable electricity by 2020. (Rourke et al. 2009)
15. Micro-Wind Turbines for Domestic Application
December 2012
14
Drivers for Deployment of Renewable Energy Technologies in Ireland
There are a number of different drivers and motivators for the deployment of renewable
energy technologies in Ireland. Some of these motivators include:
• Security of energy supply
This can be spilt into three separate sub-motivators. The first of these sub-motivators is
the fact that fossil fuels pose a threat to energy supply. The second deals with rising
political issues between fossil fuel producing countries as a result of fossil fuel resource
distribution. Finally the third sub-motivator deals with economic disadvantage, including
the risks associated with disruption of supply and the disadvantage on the balance of
payment which is dependent on fuel price. (Rourke et al. 2009) The use of renewable
energy technologies such as micro-wind turbines increases the security of energy supply
because they generally utilise indigenous resources. Energy from renewable technologies
will contribute towards a sustainable energy future.
• High fossil fuel prices
This is a major driver for the competitiveness and utilisation of renewable energy
technologies. Since 2006 the price of fossil fuels, and in particular oil prices, have
increased significantly. The continual price rises may provide an essential motivator for
investments in renewable energy technologies. (Rourke et al. 2009)
• Environmental concerns
The use of renewable energy technologies as a replacement for fossil fuel energy systems
offers a lower lifecycle impact in reducing gas emissions. (Rourke et al. 2009) Micro-
wind turbines will help towards lowering gas emissions in Ireland. However, the visual
impact of micro-wind turbines may pose a negative effect on the environment.
• Technology development and business perspective
An important driver for governments and industries to invest in renewable energy
technologies is the continuous development in technology and business perspectives. For
countries who want to maintain competitiveness in the global market and who want to
increase employment they must put actions in place to increase R&D. (Rourke et al.
2009)
• Agriculture, rural and social issues
It is possible to use wind in rural areas were population is low because wind energy
technology does not always require a grid connection.
16. Micro-Wind Turbines for Domestic Application
December 2012
15
Wind energy in Ireland
Geographical Positioning
As a result of its geographical positioning, Ireland is ideally situated to be a major producer
of wind energy. Ireland has some of the best wind conditions in the world for generating
electricity, particularly along the north and west coasts. Currently, the number of grid
connected and operational installed wind capacity on the island of Ireland is 2054.86
Megawatts (MW), which will on average generate 5,580,178 (MWh) in a given year given a
31% load. (Irish 2012)
Wind is intermittent and unpredictable in nature, challenging the integration of wind turbines
into the electricity system. The wind energy resource in Ireland is four times that of the
European average. (SEAI 2012c) The electricity output of a wind turbine is dependent on
wind speed, and is proportional to the wind speed cubed. (Twidell and Weir 2006) So,
basically the siting of the micro-wind turbine is important as electrical output is dependent on
location.
Figure
2:
European
wind
Atlas,
Onshore
(Wind-‐Energy
2012)
17. Micro-Wind Turbines for Domestic Application
December 2012
16
Colour On Map Open Plain (m/s) At sea (m/s) Open sea (m/s) Hills and ridges (m/s)
>7.5 >8.5 >9.0 >11.5
6.5-7.5 7.0-8.5 8.0-9.0 10.0-11.5
5.5-6.5 6.0-7.0 7.0-8.0 8.5-11.5
4.5-5.5 5.0-6.0 5.5-7.0 7.0-8.5
>4.5 >5.0 <5.5 >7.0
Table
1:
Wind
resource
at
50
metres
above
ground
level
for
five
diferent
topographic
conditions
From the table above, the purple and red areas on the European Wind Atlas indicate the
highest wind speeds in Europe. Ireland has either an excellent or very good wind condition as
you can see from the map with wind speeds in open plain areas reaching greater than 7.5m/s
in certain places along the west coast. This is due to its geographical location on the
downside of the Atlantic Ocean. The country is subjected to a prevailing south-westerly wind
current resulting from the Gulf Stream with windy depressions developing over the Atlantic
Ocean and crossing over Ireland. These weather systems in combination with our long
coastlines mean that Ireland is well suited to produce electricity from wind energy. (Cooke
2004)
Wind Speeds in Ireland
The author has tabulated the following tables, which indicate the monthly wind speeds of
fourteen different weather stations throughout Ireland. Taking this information from the Met
Éireann Monthly Weather Bulletin, the author was able to calculate the mean average
monthly wind speed, the average yearly wind speeds and the average wind speeds over the
three years.
21. Micro-Wind Turbines for Domestic Application
December 2012
20
The monthly average wind speeds of the fourteen weather stations were calculated using the
following formula:
!ℎ! !"# !" !"#$ !"##$! (!/!) !"# !"#$%&'("# !"#$ℎ
!ℎ! !"#$%& !" !"#$ℎ!" !"#"$%&!
The average wind speed of the year in question was calculated using the following formula:
!ℎ! !"# !" !ℎ! !"#$ℎ!" !"#$!%# !"#$ !"##$! ! !
!ℎ! !"#$%& !" !"#$ℎ! !" ! !"#$
The average wind speed over the three year period was calculated using the following
formula:
!ℎ! !"# !" !ℎ! !"!"#$! !"#$%! !"#$ !"##$! (! !)
!ℎ! !"#$%& !" !"#$%
The results are displayed in the table below:
Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Yearly Av. Av. 3 yrs.
2009 10.5 7.7 10.3 10.2 10.3 7.5 8.8 9.9 8.0 8.4 12.9 9.5 9.5 9.4m/s
2010 8.2 6.9 8.4 7.8 7.3 7.1 9.2 8.1 8.9 9.0 9.7 6.7 8.1
2011 7.8 10.5 7.0 8.0 12.9 10.5 7.3 7.4 11.8 11.1 11.7 11.1 10.68
Table
5:
Calculated
monthly,yearly
and
3
year
average
wind
speeds
(m/s)
This table indicates that the necessary conditions exist in rural areas for micro-wind turbines
which require a start-up of as little as 2.5m/s of a wind speed(GreenTech 2012), to produce
electricity. Every proposed site would, however, have different wind speeds. Wind speeds
are directly affected by the degree of exposure, the smoothness / roughness of the terrain and
the presence of obstacles. Weather stations give a rough guide to the wind conditions in
particular localities. (Cooke 2004)
22. Micro-Wind Turbines for Domestic Application
December 2012
21
Figure
3:
Wind
speeds
(m/s)
in
Ireland
50
meters
above
ground
level.
(SEAI
2012)
23. Micro-Wind Turbines for Domestic Application
December 2012
22
The
Operation
of
a
micro-‐wind
turbine
Micro-Generation
Micro wind turbines evolved from the Micro-Generation. This is a generation of heat or
electricity derived from renewable or low carbon sources on a small scale. Micro-Generation
can be described as a generation of zero or low-carbon heat and power by small businesses,
individuals and communities in order to meet their own needs.(Irish 2012) Micro-Generation
focuses on three distinct areas, Solar photovoltaic, hydroelectricity power and wind.
Solar Photovoltaic
Solar Photovoltaic is one of the micro-generation technologies which generate electricity
from panels absorbing the heat from the sun. An array of solar panels is sited in the direction
of the sun. When the heat of the sun hits the panels, dc current is generated. This is simply
converted into ac current and then fed back into the buildings electricity current. Solar P.V
systems are usually connected to the national grid and any surplus electricity created is
exported to the grid whereby the owner receives a payment based on the amount of electricity
exported. (Solar 2012)
Hydroelectricity
This is the micro-generation technology which captures potential energy contained in flowing
water and converts it into electricity. There is no carbon emitted in the production. In order to
use this system, a sufficient water flow is required – the faster and wider the better. Also
there must be sufficient head; this is the vertical drop between the water level and the intake
point were the water passes through the turbine. (Partners 2012)
Wind
In relation to wind, micro-wind turbines are small scaled wind turbines designed in such a
way to capture and convert an inherently variable raw material (wind) which is unlimited,
free and 100% green into electricity. (Partners 2012) The blades on a turbine rotate when the
wind blows and this turns a drive shaft that generates dc current which is then converted into
ac current so that it can be used within the building. The location of this of a micro-wind
turbine will have a major effect on its performance. It performs best near the coast, on high
ground, or on flat open spaces. (Irish 2012)
History
The natural forces of wind have been used for centauries as a free source of energy. It has
been used for years by windmills to power machinery for carrying out physical work such as
pumping water and crushing grain. (trust 2012)In the world we live in today, wind
technology has advanced and it is now used to generate electricity by converting the rotation
of turbine blades into electricity.
24. Micro-Wind Turbines for Domestic Application
December 2012
23
How does it work?
One of the best ways to understand the operation of a wind turbine is to imagine that it works
in the opposite way to a fan. Instead of using electricity to generate moving air, turbines use
the wind to generate electricity. (BWEA 2006)
The operation of a micro wind turbine is very straightforward. The turbine consists of the
following parts:
• Propeller / blades
• Rotor
• Generator / Alternator
• Gearbox
• Nacelle
• Tower
Figure
4:
Micro-‐Wind
Turbine
Components
(Government
2012)
25. Micro-Wind Turbines for Domestic Application
December 2012
24
Figure
5:
Electrical
output
of
a
Turbine.
(EAI
2012)
The propeller or the large blades are used to catch the wind. When the wind blows, the blades
are forced around, driving the turbine around resulting electricity being generated. The speed
of the wind will depend on the amount of electricity produced – the stronger the wind, the
more electricity. (trust 2012) Most micro-wind turbines will generate direct current (DC).
Since this is the case in most situations, a DC-AC convertor is used. After the electricity is
produced by the turbine, it is sent into the DC-AC convertor so that it can be used in the
home. Some systems in rural areas where it may not be possible to get connected to the
national grid use batteries to store the electricity produced. In most situations the system will
be connected to the national grid and any surplus electricity produced is metered and
exported to the national grid. In this case, the owner will receive a payment from their
electricity company. The amount received will depend on the amount of electricity
exported.(trust 2012)
Figure
6:
How
a
Micro-‐Wind
Turbine
work
in
a
home.
(trust
2012)
26. Micro-Wind Turbines for Domestic Application
December 2012
25
Site Selection
The selection of the site in which the turbine will run will have a major effect on its overall
performance. To assess the feasibility of installing a micro-wind turbine on a site, several
factors have to be considered:
• Wind speed
• Wind obstacles
• Topography
• Planning permission
Wind speed
Sustained wind speeds are essential to a projects economic viability. Micro-wind turbine
require a minimum average wind speed above 6m/s. The minimal difference in wind speed
causes a large difference in the amount of energy that can be generated. Wind speeds of
around 7.2m/s can produce 1.5 times the amount of electrical energy when compared with
wind speeds of 5.8m/s using the same turbine. (WindScout 2012)
Wind Obstacles
The turbines wind resource can be reduced if the wind becomes turbulent or blocked entirely
when obstacles such as trees, hedges and buildings are situated near the turbine. This is true
for back gardens or in urban areas where buildings can block or disturb wind flow.
Topography
The height incline and orientation of the site and its surroundings can have a large impact on
both the wind resource available but also the magnitude of the effect that a turbine has on its
environment. Sites which reside on the peak of hills often have a greater wind resource but
also have a greater impact on its environment which can cause planning to be more
challenging. Sites were the turbine is placed on the side of hills is often more beneficial as it
has the advantage of strong winds and it is only visible from half as many places as it is
blocked by the hillside. However; this means that the wind from that direction will be
reduced so prevailing wind direction is important. (WindScout 2012)
Planning Permission
Small scaled wind turbine projects are quite often exempt from having to obtain planning
permission once the owner follows the regulations set out in the Planning and Development
Regulations. (Environment 2007)
27. Micro-Wind Turbines for Domestic Application
December 2012
26
Technology
Smart Meters
An introduction to Smart Meters
It is expected that smart meters are going to change the way we use electricity because
instead of using the standard kWh measurement, they use a time based tariff which means the
consumer will now pay a higher price for electricity during the day time and less for it in off
peak periods. (Purcell 2008) Smart meters are the next generation of electricity meters
offering us with the potential for remote operation, remote meter reading, real time pricing,
new tariff options and demand side management (DSM) and an interface with home area
networks. (ESB 2012c) They provide us with additional features compared to those that exist
on the traditional electromechanical electricity meters that are familiar to most people. (SEAI
2012b)
The principal characteristics of smart meters are:
• They have the ability to distingush between the import and export of electricity while
keeping a record of this data at the same time.
• They are able to display and record real time information.
• With a smart meter, there is no longer a need for a meter reader to come and take
readings from your meter box or a need for the consumer to submit a meter reading.
This is because there is now communication between a central control location and
each smart meter which allows readings to be transmitted.
• Smart meters give the owner the opportunity to switch the electricity supply to the
premises on or off.
(SEAI 2012b)
How do Smart Meters work?
A smart meter works based on wireless transmitting data as energy is being consumed. Smart
meters use the information recorded as a way of keeping the consumer informed and updated
on their actual energy usage. They give you control over when you choose to either increase
or decrease your energy usage. The digital reader within the smart meter makes billing a lot
easier to track. (TheGreenAge 2012)
The purpose of smart meters is an attempt at lowering the levels of energy consumption,
which in turn will reduce the carbon emissions from buildings. These meters are ‘smart’ in
that they enable the consumer to act sophisticated when they consume energy. This is
possible because the meter displays readings during both peak and off-peak periods. Since
electricity is cheaper during off-peak times, the consumer can decide when to run certain
appliances in order to cut there bill, for example, run washing machine during off-peak times.
(TheGreenAge 2012)
28. Micro-Wind Turbines for Domestic Application
December 2012
27
The current Smart Meter situation in Ireland
A trial run on smart meters began in January 2010 with ESB networks installing 10,000
meters. This trial basis was hoped to educate stakeholders in smart meters and how they can
help the consumer best manage their electricity. (ESB 2012c) The national ‘Smart’
programme got under way on the 17th
of November 2011 when Electrical Supply Board of
Ireland (ESB) and the European investment bank agreed on a €235 million loan to fund the
‘Smart’ investment in Ireland’s electricity networks. The programme includes a number of
key projects to enhance transmission and distribution links from wind farms, to improve the
efficiency and capability of the electric networks to facilitate greater integration of renewable
energy sources and also the technical design phase of a national smart metering programme.
(ESB 2012b)
The CER (Commission for Energy Regulation) announced their energy smart metering
decision on the 4th
of July of this year (2012). (CER 2012a) This decision proves a vital step
towards lowering customer bills and also towards Ireland lowering its CO2 emissions in an
attempt to combat climate change.
It is due to the major success of phase one (Pilot trials and cost benefit analyses) that led to
the CER’s decision in proceeding to the next phase of the project. Phase two of the national
program involves the rollout of electricity and gas smart meters to all homes and businesses
with the idea that they will provide significant benefits to energy customers and to the entire
country in general. Trials that were carried out in 6200 homes and businesses showed us that
an average saving of 2.5%. Therefore it is hoped that a national rollout of smart meters would
give us a 2.5% reduction in the overall electricity consumption. This does not seem like a
great amount but it is a saving and a stepping stone in the right direction. A national rollout of
smart meters will lead to a drop in customer bills, provide customers with more information
about their electricity usage and also lower Irelands CO2 emissions which will help the
environment in the long run. (CER 2012a)
The rollout of smart meters will involve major investments by network companies over the
next few years. The pilot trials that were successfully carried out in phase one showed us that
after carefully analysing the cost and the benefits involved, using very considerate estimates,
smart meters will provide a net benefit to customers and to the country within the region of
€220 million over twenty years. (CER 2012a)
Ireland is among the first to roll out smart meters, however unlike other countries with a
similar system, homes and businesses here will be fitted with a display unit which allows
people to see their actual energy consumption in real time. The installation of these smart
meters is expected to begin in 2005 and 2.2million homes and 600,000 businesses will be
upgraded within four years. (Independent.ie 2012)
29. Micro-Wind Turbines for Domestic Application
December 2012
28
Grid Connection
The installation of a renewable energy system is generally quite simple regardless to whether
it is being incorporated in a new building or being retrofitted into an existing building. A
renewable energy system being retrofitted into an existing building is quite straight forward
because the building concerned is usually wired for electricity and the electricity is all the
same. In a situation where the renewable energy system is required to operate normally
during a power cut or during network upgrades, then it is necessary to avoid direct grid
connection as well as the selection of either a PGT or Off-grid system. A PGT system has the
advantage of exporting at the generators preferred time so that it will benefit from the highest
value tariffs during the day. When using a micro-wind turbine as part of a renewable system
the use of a PGT grid connected system where excess grid connected power is stored and off-
grid systems where all power is stored are recommended ahead of the basic grid connection.
Almost all domestic micro-wind turbines do not require maintenance compared to the larger
scale wind turbines which are subject to commercial type installations due to their significant
installation requirements and blade size. They also have the added problem of noise ratings to
be considered. (Wineur 2005)
Basic Grid Connection
This connection requires the operation of the grid; therefore it does not work during a power
cut, or during upgrades etc. If the consumer is generating energy from their micro-wind
turbine, this energy automatically goes into a utility connected inverter and then directly into
the wiring of their property. The result of doing this is that the consumer uses the energy
produced by the turbine first and then then the incoming electricity from the grid second. The
financial feasibility of micro-wind turbines used in a basic grid connection is currently poor
due to a significant amount of spillage onto the grid during the night when virtually no
electricity is being used. Therefore this means that micro-wind turbines that are basically grid
connected will have an unviable payback period. The smart metering applies a higher
daytime tariff and a lower night-time tariff which also does not make the payback period
much shorter or viable. In the current market conditions, basic grid connected micro-wind
turbines do not make economic sense.
Advanced Grid Connection
Unlike the basic grid connection, this system does not require the operation of the grid as it
contains a private grid generator. Basically, it has all the functionality of a grid connected
system with all the functionality of an off-grid system. It is fully automatic and stores excess
amounts of electricity. This system has inverters that can be rated and expanded up to
hundreds of megawatts. The financial feasibility of micro-wind turbines used in conjunction
with this system are more favourable since the system is able store electricity. Smart metering
will apply at a higher tariff during the daytime and a possible zero night-time tariffs which
means the energy generated at night can be stored until day-time and then exported at the
higher daytime tariff making the payback period shorter and more achievable. Wind systems
30. Micro-Wind Turbines for Domestic Application
December 2012
29
that are directly connected to a storage system get the full benefit of energy produced. The
best advanced grid systems are solar photovoltaic or solar/wind hybrid systems.
Off-Grid Connection
This system does not need the grid to operate but it does however require a base support
coming from either the grid or a standalone generator if there is not grid available (i.e. in
rural areas). This arrangement creates an independent system that can be expanded over time.
It is fully automatic and can store excess amounts of electricity. Since the system has a
storage unit, the financial feasibility of a micro-wind turbines used in conjunction with this
type of system is relatively good. It is possible to double or even treble the amount of energy
generated by simply installing more than one micro-wind turbine. While this would increase
the power outage, the system would still remain relatively maintenance free. These system
are directly connected to a storage system for full benefit of energy produced and the best
being solar photovoltaic or solar/wind hybrid systems. (Purcell 2008)
Hybrid Sources of Input
A hybrid system contains more than one type of input technology, i.e. solar and wind. When
developing a hybrid specification for which sources of input to use, consideration of the
output profile versus the usage profile is needed, i.e. if energy is used every day in a similar
fashion, then maybe one might begin with solar P.V panels, and then if the site was suitable
for wind, then turbines may be added. (SouthWestWindPower 2011)
Installation and Operation
The installation of a basic grid connected system can be as simple as erecting a micro-wind
turbine on the ground and running two cables from the turbine to a wall mounted utility
inverter and then simply plugging it in and it’s online automatically. Installing an advanced
grid connected system is quite similar except a PGT inverter is installed instead of a utility
inerter and a grid manager needs to be cabled and mounted and then as before it just needs to
be plugged in. Larger systems will need to be connected into the electrical supply buzz bar of
the building. (Purcell 2008) This is a quick job but the work must be carried out by a
qualified electrician to ETCI standards. (ESB 2012a)
The operation of a basic and advanced and the off grid connected systems are fully automatic
when they are installed. The basic grid connected system has the effect of slowing down the
electricity meter and if production is the same as the amount of electricity being used the
meter will stop. While the advanced grid connected system gives the benefits of both on and
off-grid capability including exporting capability, storage and independence in grid failures.
(Purcell 2008)
31. Micro-Wind Turbines for Domestic Application
December 2012
30
Current Standards and Regulations for Connecting a Micro-Generator in Ireland
According to ESB networks, all direct grid connections must comply with the European
standards EN 50438 which was published in 2007 and enacted into law in 2008. (ESB 2012a)
This standard restricts the amount of plate rating of renewable equipment, which can be grid
connected. The maximum plate rating on a single phase is 5.75 Kw and up to 11 Kw plate
rating on triple phase, however ESB networks currently accept applications for generators up
to 6 Kw on a single phase. (SEAI 2012a) A licence and network notification to the ESB is
required when connecting to the grid. PGT grid connected systems are however designed to
be exempt from the standard and hence no limit on the amount applies, neither is there any
requirement for regulator licence or DSO network approvals. Full export control for smart
metering is configurable with a PGT system but excess energy is stored or exported by choice
unlike basic grid connections where unused energy is spilt onto the grid.
Technical standards apply to all utility connected systems including many EN standards and
local network interface settings. Under EN 50438, advanced grid connections are not
restricted in size on single phase or on triple phase. (CER 2012b) All off-grid systems must
comply with CE standards, a European product standard covering all member states. (SEAI
2012a) These systems are fully independent as they are not connected to the gird. Off-grid
inverters have a maximum rating depending on the system, this upper value cannot be
breached, i.e. 2000 watt inverter means that it will disconnect when the load goes over 2000
watts, for example, all of a houses lights, TV, PC and supplementary items would equate to
approximately 400-500 watts continuous power. All basic grid connections require licensing
and a network approval, this is usually taking care of by the micro-wind turbine installers.
However, all advanced grid connections are exempt from licensing and network approvals
unless the export option is required. (Purcell 2008)
32. Micro-Wind Turbines for Domestic Application
December 2012
31
The current micro-wind turbine situation in Ireland
The best way to describe the micro-wind turbine situation in Ireland today is under the
following four headings:
1. The current micro-wind turbine market
2. Micro wind turbines available
3. The current legislation and regulations regarding the installation of micro-wind
turbines
4. Financial support for exporting electricity generated by micro-wind turbines
The current micro-wind turbine market
To date, the micro renewable electricity generation has not been very popular here in Ireland.
However, the most popular device of the micro generation for generating electricity is the
micro-wind turbine. (Li et al. 2012)In the diagram below (fig 1), you can see that 579 micro-
wind turbines have been registered with the ESB and been connected to ESB Networks (grid)
from January 2007 to February 2010. (Li et al. 2012) This electricity accounted for 84% of all
grid-connected micro renewable electricity generation devices in this period. In fig 2, you can
see that 357 micro wind turbines were installed and grid connected by the end of 2010. (SEAI
2010) It is expected that the total number of installed micro-wind turbines is much higher, as
a small number of micro-wind turbines are either connected with batteries or are waiting to
get connected to ESB networks. Although there are vast amounts of wind resources available
here in Ireland, micro-wind turbines have not yet become an attractive renewable energy
technology in electricity generation. There are a few major factors that may affect
householders’ decision on purchasing a micro wind turbine, including the cost of the turbine,
the government grant available, the loan rate from a bank or a credit union, or the imported /
exported electricity price.(Li et al. 2012)
Figure
7:
Breakdown
of
grid
connected
micro
renewable
electrical
generation
devices
installed
from
January
2007
to
February
2010
in
Ireland.
(Li
et
al.
2012)
Grid-‐connected
devices
from
January
2007
-‐
Febuary
2010
Wind
energy
(84%)
Combined
Heat
and
Power
(2%)
Solar
energy
(14%)
33. Micro-Wind Turbines for Domestic Application
December 2012
32
Figure
8:
Market
share
by
installation.
(SEAI
2010)
December 2010 kW Installed
Capacity
Market Share by
Capacity
No. of
installations
Market share by
installation
Micro CHP
Micro Hydro
Solar PV
Micro Wind
Total
3.00
20.8
120.78
1818.15
1962.73
.2%
1.1%
6.2%
92.6%
100%
3
4
55
357
419
.7%
1%
13.1%
85.2%
100%
Table
6:
Total
installed
capacity
of
Micro-‐Generators.
(SEAI
2010)
Micro-wind turbines available on the Irish Market
The Micro-generation Certificate Scheme (MCS) is an industry led and internationally
recognised quality assurance scheme supported by the department of energy and climate
change. The Micro-generation Certificate Scheme itself is an EN 45011 scheme and it was
launched in 2008. The scheme certifies a number of installation companies to ensure that all
micro-generation products (i.e. micro-wind turbines, Solar PV’s etc.) are installed and
commissioned to the highest of standards. (MCS 2012)
The micro-generation certificate scheme certifies micro generation products and installers for
Ireland and the UK in accordance with consistent standards. The scheme provides a list of
registered micro-wind turbines that are currently available on the Irish market. (Li et al.
2012)The turbines listed in the scheme are reliable, robust and can be purchased with ease
from suppliers in the UK and Ireland, e.g. The KW6 by Kingspan Wind, and the CF6e by
C&F Green energy. Both turbines are shown in Fig 3 below.
The wide range of wind turbines should be sufficient to satisfy householder’s needs under
individual circumstances, i.e. location, wind speed and the household electrical load
required.(Li et al. 2012)
Market
Share
by
InstallaXon
by
of
2010
Micro-‐Wind
(85.20%)
Solar
PV
(13.10%)
Micro-‐Hydro
(1%)
Micro-‐CHP
(0.7%)
34. Micro-Wind Turbines for Domestic Application
December 2012
33
Figure
9:
Kingspan
KW6.
(Beco,
2012)
Figure
10:
KW6
showing
power
production
against
wind
velocities
(m/s)
This turbine is one of the most popular small scale wind turbines. The KW6 wind turbine
stands out from all other small scale wind turbines due to its unique blade and hinge design
which allows it to regulate its rotational speed, maximising output – as the wind gets stronger
the blades pitch and cone, protecting the turbine and allowing continual operation during the
fiercest of storms. (Beco 2012)
The KW6 is targeted at a large range of domestic dwellings and agricultural sites making it
extremely versatile and suited to a wide range of energy clients. At present, Renewable
energy systems Ireland (MCS Certified) has installed a KW6 in every county in Ireland.(RES
2012)
(Kwh)
Wind
speed
(m/s)
35. Micro-Wind Turbines for Domestic Application
December 2012
34
Figure
11:
C&F
Green
Energy
CF6e.
(C&F-‐GreenEnergy,
2012)
Figure
12:
CF6e
showing
power
production
(kW)
against
wind
velocities
(m/s)
The CF6e is recognised as the most efficient small wind turbine in the world today.
Compared to the KW6, the blades are much bigger giving an overall rotor diameter of 8m
with the KW6 at 5.5m. Bigger blades have been proven to give more power but demand a
more sophisticated control mechanism. C&F have developed megawatt turbines control
technology which allows power to be produced during the lowest of wind speeds as well as
during the highest of wind speeds. (C&F-GreenEnergy 2012)
Power
(kW)
Wind
Velocity
(m/s)
36. Micro-Wind Turbines for Domestic Application
December 2012
35
The turbine includes a yaw actuator. A wind direction van and cup anemometer is monitored
by the turbine microprocessor, which activates the yaw motor to align the turbine into the
wind. This feature is usually only employed on larger scale wind turbines but C&F have
cleverly incorporated it into the CF6e optimising the performance and energy yield. (C&F-
GreenEnergy 2012)
The Irish times released an article in December 2011 stating that C&F had announced an
almost 40% rise in their sales from 2009 to 2010 showing us that all C&F turbines including
the CF6e are becoming increasingly popular. (IrishTimes.com 2011)
The current legislation and regulations for installing a micro-wind turbine in
Ireland
The installation of a domestic wind turbine in Ireland is usually subject to planning
permission. However, if the turbine is installed under certain conditions, it may be exempt
from planning permission. In 2007, the Irish government released a report called Planning
and Development Regulations, clearly stating the conditions in which a micro-wind turbine
may be exempt from planning permission. The report states that:
1. The turbine shall not be erected on or attached to the house or any building or other
structure within its curtilage.
2. The total height of the turbine shall not exceed 13 metres.
3. The rotor diameter shall not exceed 6 metres.
4. The minimum clearance between the lower tip of the rotor and ground level shall not
be less than 3 metres.
5. The supporting tower shall be a distance of not less than the total structure height
(including the blade of the turbine at the highest point of its arc) plus one metre from
any part boundary.
6. Noise levels must not exceed 43db (A) during normal operation, or in excess of 5db
(A) above the background noise, whichever is greater, as measured from the nearest
neighbouring inhabited dwelling.
7. No more than one turbine shall be erected within the curtilage of a house.
8. No such structure shall be constructed, erected or placed forward of the front wall of a
house.
9. All turbine components shall have a matt, non-reflective finish and the blade shall be
made of material that does not deflect telecommunication signals.
10. No sign, advertisement or object, not required for the functioning or safety of the
turbine shall be attached to or exhibited on the wind turbine.
(Environment 2007)
37. Micro-Wind Turbines for Domestic Application
December 2012
36
In a situation where the installation of a micro-wind turbine for domestic use does not
satisfy the above conditions, it must undergo the planning process. Although it has to
undergo the planning process, permission may still be given, especially if the turbine does
not meet the height requirement only. A roof-top-mounted wind turbine does not qualify
for exemption from planning permission; it must be considered on a case by case basis.
In order to protect the grid, the maximum rated output from a grid-connected micro wind
turbine is subjected to a limit. When the connection is single phase, the maximum output
is 6kW or if the connection is three phase, the maximum output is 11kW. (ElectricIreland
2012) Any micro-wind turbines that fail to comply with these limitations will not be
allowed to connect to ESB Networks as it may cause grid disruption.
The Current financial support for exporting electricity generated from micro-
wind turbines
At the moment, ESB Networks are paying €0.09 to the householder for every kWh of
electricity exported to ESB Networks from a micro electricity device in Ireland. This price is
a standard payment tariff and there is no restriction on the amount of electricity sold. The
ESB offer incentives as an attempt to try and encourage householders to utilise micro
renewable generation technologies. A supplementary €0.10 is added on for every kWh of
exported electricity; however it is capped at 3000 kWh per annum and applies for a
maximum of five years from the start of the contract. This contract is signed with ESB
Customer Supply and allows householders to generate electricity for their own use and export
any excess through an import/export meter to ESB networks. (Electric Ireland)
38. Micro-Wind Turbines for Domestic Application
December 2012
37
Case Studies
Case Study 1: Householder’s Micro-Wind Turbine Project
Location – Credition, Devon, England, United Kingdom
Mr John Lightfoot first considered micro-generation in an effort to become more sustainable
and also to save on electricity. He researched many different renewable energy sources and
this led him deeper into actually considering investing in a renewable energy device. He
travelled to an exhibition on renewable energy and after talking to several renewable energy
companies; he decided that a micro-wind turbine would be best suited for his property as it is
located on a hill with no obstructions, which is an ideal location for a wind turbine as it will
obtain higher wind speeds.
(LowCarbonBuildingProgramme 2006)
John found the installers at the exhibition very helpful. Not long after the exhibition, one of
the micro-wind turbine installers he met with at the exhibition came to his home and carried
out a site analysis to see if his home was suitable for a micro-wind turbine. After the installer
completed the site analysis, John was told that his site was suitable.
Average wind speeds of Credition, Devon = 4.6 m/s (RenSMART 2012)
John then applied for planning permission to his local council and also contacted a number of
Micro-generation Certified Scheme (MCS) installers to obtain quotes. The council came to
do a site visit and with help from his accredited installer, he managed to obtain planning
permission very easily. (LowCarbonBuildingProgramme 2006)
After been approved planning permission, John began to investigate renewable energy grant
schemes that he may be entitled to. (LowCarbonBuildingProgramme 2006) He found out
about the Low Carbon Buildings Programme grant scheme who provided funding for the
installation of renewable energy applications (i.e. wind turbines, solar P.V’s etc.). The initial
value of the grant was unknown as the value of the grant was dependent on:
1. The sector the application was in (i.e. householder, organisation etc.).
2. The chosen technology (i.e. wind, solar, hydro etc.).
3. If the installation was for a ‘new build’ or a retro-fit building.
(Gardiner et al. 2006-2011)
Therefore since every case was different, the amount of financial support that John would
receive was unknown during the initial stage of the project. However the Low Carbon
Building Programme grant on average represented roughly 10 to 28% of the equipment and
39. Micro-Wind Turbines for Domestic Application
December 2012
38
installation costs. (Gardiner et al. 2006-2011)
Before John could finally apply for the grant, he had to complete one of the requirements set
out by the Low Carbon Building Programme. (LowCarbonBuildingProgramme 2006)He had
to upgrade the insulation in his home as the Low Carbon Building Programme required a
minimum level of insulation installed in the property. (Gardiner et al. 2006-2011) He found it
relatively cheap to install the energy efficiency measures required to receive the grant. These
measures also helped to improve heat retention and reduce energy consumption. He then
applied for the grant online filling in the necessary details on the application form.
(LowCarbonBuildingProgramme 2006)
Once he had received confirmation of his grant approval John began marking out the selected
site for his micro-wind turbine. He carried out some of the groundwork himself along with
the help of some local builders. This was not difficult and only took about two working days
with minimal disruption. When the site was ready, his Micro-generation Certified Scheme
installers (Natural Generation) came to fit the turbine. (LowCarbonBuildingProgramme
2006)
The selected turbine was a 6kW Proven.
Figure
13:
6kW
Proven
(caredelyn.co.uk)
40. Micro-Wind Turbines for Domestic Application
December 2012
39
The Proven 6kW wind turbine is the result of 25 years research and development and it is
renowned for its quality and durability. It is capable of supplying enough electricity to run an
average sized home. (MandCHybridEnergy 2012)
The author has calculated the rotor COP (Coefficient of Performance) of Johns Proven 6Kw
micro-wind turbine.
Description :
Rotor diameter 5.5m (BetterGeneration 2012)
Density of air 1.2
Average wind speed of Credition, Devon 4.6m/s (RenSMART 2012)
Efficiency of conversion of rotational energy
to electrical energy.
27% (BetterGeneration 2012)
Rotor COP:
Power of wind
=
!
!
! ! ! !!
! !
=
!
!
! 1.2 ! 4.6!
! (
!(!.!!)
!
)
= 58.4 ! 74.63
= 4358.5 !"##
= 4.3 !"
Mechanical energy at the rotor
= !ℎ!"# =
!.!
!.!"
= 15.92 !"
Therefore, the rotor COP
=
!.!
!".!"
= 37.6%
The turbine was successfully fitted in one day and it was very straightforward. The installers
gave him all the information he needed including maintenance instructions and were they
were very friendly. Overall, the only unexpected cost of project was the connection fee that
John had to pay to get the turbine connected to the national grid. However, thankfully the
41. Micro-Wind Turbines for Domestic Application
December 2012
40
connection fee was only small. (LowCarbonBuildingProgramme 2006)
As a result of the installed micro-wind turbine, John now produces more than twice as much
electricity as he uses and he is selling the excess back to the grid. In Ireland when you
produce excess electricity from your micro-wind turbine you simply sell it back to the ESB;
however in the UK the process is quite different. John had to find a supplier that would buy
his electricity. He was advised to shop around and so he did. He found that his installer was
very helpful in suggesting possible companies to sell his electricity to. He now reads his
meter every month and sends the information to the company every three months and
receives a cheque in the post for his exported electricity. (LowCarbonBuildingProgramme
2006)
Costs and Savings:
Description :
Average domestic electricity bill in the UK in 2011 £453 (Change 2011)
Cost of electricity per kWh £0.13p (Change 2011)
Annual yield from turbine 10000kWh
(LowCarbonBuildingProgramme 2006)
Total costs of project (incl. Parts, installation,
connection, etc.)
£18,763.10p
(LowCarbonBuildingProgramme 2006)
Low Carbon Building Programme Grant (13.3% of
overall cost)
£2500 (LowCarbonBuildingProgramme
2006)
Maintenance charge £100 per/year
Payback Period:
Estimated electricity usage per year
=
£"#$
£".!"!
= 3484.6 !"ℎ
Excess electricity being produced by the turbine
= 10000 !"ℎ − 3484.6 !"ℎ = 6515.4 !"ℎ
Amount of money received for exported electricity
= 6515.4 !"ℎ ! £0.13! = £847 !"#/!"
Annual savings
= £453 + £847 = £13000 !"#/!"
Therefore, the payback period for John’s micro-wind turbine is:
=
!"#$%"& !"#$%&'$"&
!""#$% !"#$%&!!!"#$%&$"$'&
42. Micro-Wind Turbines for Domestic Application
December 2012
41
= £18,763.10! − £2500 = £16,263.10!
=
£"#,!"#.!"!
£"#$$!£"##
= 13.5 years
John says the best benefit he has found from the turbine is a great ‘feel good factor’ that he is
producing his own electricity, saving carbon and also saving some money at the same time.
He thinks that the overall project was a success and money well spent and says ‘knowing
what I know now I would have gone ahead with the installation even without the grant. He
has had interest from some of his friends and thinks that he may have convinced them to get a
micro-wind turbine too! (LowCarbonBuildingProgramme 2006)
43. Micro-Wind Turbines for Domestic Application
December 2012
42
Case Study 2: Householder’s Micro-Wind Turbine Project
Location – Gowna, Co. Cavan, Ireland
When Patsy completed the build of his family home in February 2008, he saw the opportunity
to make an investment that would hopefully pay off in the long run. “My initial motivation
when building my house was to incorporate a renewable energy device in order to reduce the
households running cost,” says Patsy.
He began researching different types of renewable energy technologies and it was while
doing this he became aware of micro-generation. He weighed out the pros and cons of each
micro-generation technology and taught about which one would be best suited for his home.
He attended the National Ploughing Championships in September 2008 and got talking to a
number of different renewable energy installers. After giving details about his home, (i.e. site
location) they were able to advise him on a type of renewable energy technology that would
be best suited for his home. He found the installers very helpful and taking their advice on
board he decided to go with a micro-wind turbine for his property which is located on a hill.
Patsy began contacting micro-wind turbine installers to obtain quotes. After getting quotes of
roughly the same price, he decided to go with M&C Hybrid Energy Ltd, a Cavan based
company whom he met with during his visit to the National Ploughing Championships. The
installers came to access the site and agreed that it was suitable for a micro-wind turbine;
however “they never carried out a site analysis to check and see what area of my property
contains the highest wind speed,” says Patsy.
Patsy was exempt from having to apply for planning permission for his wind turbine because
his project fell within the regulations set out by the department for the environment, heritage
and local government (Planning and Development Regulations 2007). (Environment 2007)
He looked into additional funding (i.e. grant aid) that he might be entitled to before the
installation of the turbine began but unfortunately there was no grant aid available at the time
and this situation still remains today. (SEAI 2012a)
Before the installation of the turbine could commence, a number of steps had to be completed
first. Patsy had to familiarise himself with the process involved in connecting a micro-
generator to the national grid. The installer read over the conditions governing the
‘Connection and Operation of Micro-generation’ (Safety 2009) with Patsy and informed him
on areas that they need to pay particular attention to. The turbines connection to the grid had
to comply with the standards set out in EN 50438. Once he was familiar with the process, he
had to inform ESB networks that he had intentions of connecting a micro-generator to the
electricity network. He was able to do this through filling out what is called an NC6 form.
After being approved by the ESB, in order to receive a payment for his exported electricity
44. Micro-Wind Turbines for Domestic Application
December 2012
43
Patsy had to order an import/export meter from the ESB.
Having completed the essential permission stages of the project Patsy began clearly the site in
which he planned to erect his micro-wind turbine. At the time he was the owner of a JCB
digger so he carried out most of the ground work himself. The whole for the foundations had
to be 2.5 meters square by 1 metre deep. The foundations included:
• 2 layers of 2.2m square reinforcing mesh 6mm or heavier with approximately 200mm
square holes.
• 100mm soil pipe or similar for cable duct, cast into the concrete.
• 35 Newton or better concrete.
When the foundation was completed the turbine was ready to be erected. This was quite a
simple process and the installers completed it within a day.
The selected turbine was a 2.5Kw Proven.
Figure
14:
2.5kW
Proven
45. Micro-Wind Turbines for Domestic Application
December 2012
44
Figure
15:
Concrete
base
to
support
11
metre
high
mast.
Figure
16:
2.5kW
Proven
on
11
metre
mast.
46. Micro-Wind Turbines for Domestic Application
December 2012
45
The author has calculated the rotor COP (Coefficient of Performance) of Patsy’s Proven
2.5Kw micro-wind turbine.
Description :
Rotor diameter 3.5m (Solutions 2012)
Density of air 1.2
Average wind speed of Co Cavan 6.9m/s (MetÉireann 2011)
Efficiency of conversion of rotational energy
to electrical energy.
39% (Greenspec.co.uk)
Rotor COP:
Power of wind
=
!
!
! ! ! !!
! !
=
!
!
! 1.2 ! 6.9!
! (
! !.!!
!
)
= 0.6 ! 328.5 ! 9.62
= 1896.1 !"##
= 1.8 !"
Mechanical energy at the rotor
= Shaft =
!.!
!.!"
= 5.1 !"
Therefore, the rotor COP
=
!.!
!.!
= 49%
The next step of the project was to electrically connect up the turbine. Patsy’s installers
brought along a registered electrical contractor to ETCI standards to carry out the electrical
work. The contractor was required to forward on a valid ETCI electrical completion cert to
ESB networks. (ESB 2012a) He also had to forward on details about the invertor (i.e. how it
works, what it will do, how it was connected, and how it will cut out during a grid outage).
After the turbine was successfully installed and the ESB had received an ETCI certificate, the
ESB came to install the import/export meter for a fee of €370. Patsy had to contact his
electricity suppliers regarding payment arrangements for any electricity that he would export
to the grid. He had to make an agreement with his electricity suppliers to purchase electricity
exported and to supply electricity imported.
47. Micro-Wind Turbines for Domestic Application
December 2012
46
Patsy found the whole experience very interesting. “There is a great feeling knowing that you
are helping to reduce our carbon footprint whilst saving money in doing so,” says Patsy.
However, with the turbine installed almost four years now he is not fully satisfied with the
results of the turbine financially. Although he is saving quite a lot on his annual electricity
bill, he feels that the initial cost of the turbine and the installation fee will prevent him from
ever being able to make his money back.
The author has calculated how long it will take before Patsy can start saving money from his
electricity bill as a result of his micro-wind turbine.
Cost and Savings:
Description :
Parts €15,175.35c
Installation costs €6825
ESB import/export meter €370
Annual yield from turbine 2500kWh
Fixed rate for every kWh exported €0.19c (ElectricIreland 2012)
Maintenance €250 every 2nd
year
Figure
17:
Import/Export
meter.
48. Micro-Wind Turbines for Domestic Application
December 2012
47
Payback Period:
Capital investment
= €15,175.35 + €6825 + €370 = €22,370.35
Net annual savings
= 2500 ! €0.19! = €475
Therefore, the payback period for Patsy’s micro-wind turbine is:
=
!"#$%"& !"#$%&'$"&
!""#$% !"#$%&'!!"#$%&$"$'&
=
€"",!"#.!"
€"#$!
€"#$
!
= 63.9 years
This calculation proves that the 2.5Kw micro-wind turbine that Patsy installed is not
beneficial. Although his annual electricity bill is cut by over half, the financial downfall is the
initial cost of parts and installation. The fact that a site analysis was never carried out by the
installers may be having an impact on the overall performance of the turbine, “When the
wind is blowing from the south west the turbine performs best, but when it is blowing from
the north it does not perform as good because the wind is being sheltered from the house and
large trees around the house,” says Patsy.
Drawing 1:
North South
49. Micro-Wind Turbines for Domestic Application
December 2012
48
Drawing 2:
As you can see from drawing one, if the wind was to blow from the North, the turbine will
not perform to its best due to obstructions from the house and large trees planted in front of
the house. However, as you can see in drawing two, if the turbine was initially installed
behind the house it would perform to its best no matter what direction the wind is blowing
from because it is sited on a higher level than the house and there is no obstructions from
trees or any other obstacles. This could increase the annual yield from 2500 kWh to the
maximum 5000kWh of a 2.5Kw turbine, therefore increasing the amount of electricity Patsy
will export resulting in a greater annual saving and a reduced payback period.
5000 !"ℎ ! €0.19! = €950
= €950 −
€"#$
!
= €825
=
€"",!"#.!"
€"#$
= 27.1 years
SouthNorth
50. Micro-Wind Turbines for Domestic Application
December 2012
49
This would reduce the payback period of Patsy’s micro-wind turbine by 39%. However, if he
had to have installed a 6Kw Proven with an annual yield of 10000 kWh instead of a 2.5Kw
Proven his payback period would be less again.
Description :
Annual yield from turbine 10000 kWh (MandCHybridEnergy 2012)
Capital Investment (Proven 6kW) €24,020.55c (MandCHybridEnergy 2012)
10000 !"ℎ ! €0.19! = €1900
= €1900 −
€"#!
!
= €1775
=
€"#,!"!.!!
€"##$
= 13.5 years
If a proper site analysis was carried out from the beginning of this project, maybe the turbine
would have been sighted in a better location (i.e. behind the house) and it would be possible
for it achieve its optimum performance of an annual 5000kWh. (Solutions 2012) However,
the main problem is that the installed turbine is not capable of producing enough electricity to
allow Patsy make his money back, and having availed of the ESB’s incentives of receiving
€0.19c for every kWh of exported electricity for three years to date, he can only receive this
for another two years. After this he will only receive €0.9c making his payback period longer
again unless new regulations are put in place regarding the price of exported electricity.
However; the ideal micro-wind turbine for his home still remains to be a Proven 6Kw.
51. Micro-Wind Turbines for Domestic Application
December 2012
50
Conclusions
Conclusions
It is evident that at present, micro-wind turbines in Ireland are an emerging piece of
technology driven by advances in design, increasing electricity prices and the potential of
financial incentives being offered by the government. Wind technology is still positioned
quite low in the electricity market in Ireland proving that the Irish public is still not entirely
convinced of the potential of this piece of technology. However, it is hoped that some of the
information and findings presented in this study will help towards informing people on the
merits of micro-wind turbines for domestic application.
The conclusions are as follows:
• Before installing a micro-wind turbine it is vital that a proper site analysis is carried
out by a MCS certified installer. This ensures that the turbine is located in the best
site possible on the proposed property which allows the turbine to achieve its
optimum performance.
• The results from both case studies show that the higher size turbine will produce a
larger amount of electricity resulting in a shorter payback period for the owner and
eventually the owner might even yield a profit.
• This study has uncovered the need for a reduction of the capital costs for micro-
wind turbines. There are a few different ways in which this could be achieved. The
first way is if the government were to offer grants for renewable energy
technologies. These grants could either be received by the supplier or the consumer
as long as it results in the reduction of the turbines capital costs. The second is for
manufactures and suppliers to reduce their production cost.
• Currently there is no value put on CO2 emission savings from renewable energy
technologies. (Purcell 2008) If this was introduced, it could help the economic
viability of this technology.
Recommendations
In any future domestic projects it is recommended that within regulation, the highest possible
micro-wind turbine is installed. This will reduce the payback period of the turbine and it will
allow the owner to eventually make a small profit through exporting electricity. Other
recommendations include:
• The government introducing a grant scheme to reduce the capital cost of micro-wind
turbines.
• A reduction of value added tax (VAT) on micro-wind turbines.
• Credits for each Kg of CO2 saved.
• Funding for micro-wind turbine manufacturers and suppliers.
52. Micro-Wind Turbines for Domestic Application
December 2012
51
References
1. Beco. 2012. Kingspan Wind 6KW Turbine.
2. BetterGeneration. 2012. Proven 11 wind turbine spec sheet.
3. BWEA. 2006. Small wind energy systems. 11.
4. C&F-GreenEnergy. 2012. CF 6e.
5. caredelyn.co.uk.
6. CER. 2012a. CER Announces Energy Smart Metering Decision. ed. C. f. E.
Regulation.
7. CER, C. f. E. R. 2012b. Micro-Generation, EN50438.
8. Change, D. o. E. C. 2011. Quarterly Energy Prices. 88. UK.
9. Cooke, N. 2004. Small-scale wind turbines - A viable alternative for the independent
generation of electricity for homes situated in rural areas of Ireland?
10. EAI. 2012. How does a turbine work.
11. ElectricIreland. 2012. Micro-generation.
12. Environment, H. a. L. G., Minister. 2007. Planning and Development Regulations.
13. ESB. 2012a. Generator Connections.
14. ---. 2012b. Press, The Latest Irish Energy News From ESB.
15. ---. 2012c. Sustainable and Environment For Generation To Come - Smart Meters.
16. Gardiner, M., H. White, M. Munzinger & W. Ray. 2006-2011. Low Carbon Building
Programe Final Report. 170.
17. Government & Irish. 2012. Renewable Energy Policy.
18. Government, S. 2012. Planning for micro renewables.
19. Government white paper 2006, I. G. Delivering a sustainable energy future for
Ireland, energy policy framework 2007-2020.
20. Greenspec.co.uk.
21. GreenTech. 2012. Green Technology Systems, Wind Turbines.
22. Independent.ie. 2012. Surviving the Recession. In New meters can knock €160 of
smart consumers' ebergy bills.
23. Irish, I. 2012. micro-generation and domestic opportunites. ed. I. W. E. Association.
24. IrishTimes.com. 2011. C&F books €7 million profit as company eyes renewable
enegy openings.
25. Li, Z., F. Boyle & A. Reynolds (2012) Domestic application of micro wind turbines in
Ireland: Investigation of their economic viability. Renewable Energy, 41, 64-74.
26. LowCarbonBuildingProgramme. 2006. Housholder's Project Case Study - Wind
Turbine.
27. MandCHybridEnergy. 2012. Wind Turbines, Proven 6kW.
28. MCS. 2012. The Microgeneration Certificate Scheme.
29. MetÉireann. 2011. Monthly Weather Bulletin.
30. Partners, U. E. 2012. Microgeneration (Wind).
31. Purcell, P. 2008. Micro-Wind Turbine installation, feasibility study for D.I.T Bolton
St., 71.
32. Regulation, C. F. E. 2011. CER fact sheet on the single electricity market. 6.
33. RenSMART. 2012. UK Solar & Wind Energy Search.
34. RES. 2012. Kingspan KW6 Wind Turbine.
35. Rourke, F. O., F. Boyle & A. Reynolds (2009) Renewable energy resources and
technologies applicable to Ireland. Renewable and Sustainable Energy Reviews, 13,
1975-1984.
53. Micro-Wind Turbines for Domestic Application
December 2012
52
36. Safety, P. O. 2009. Connection and Operation of Micro-generation.
37. SEAI. 2010. Status Report on Microgeneration in Ireland at the end of 2010. 4.
38. ---. 2011. Energy in Ireland - Key Statistics.
39. ---. 2012a. Micro-generation.
40. ---. 2012b. Renewables - Smart Meters.
41. ---. 2012c. Wind Maps.
42. Solar, S. 2012. Solar Micro-Generation Systems.
43. Solutions, A. R. E. 2012. Proven 2.5kW Spec Sheet.
44. SouthWestWindPower. 2011. The role of small wind turbines in hybird power
systems for telecom sites.
45. TheGreenAge. 2012. Green Home - Energy Efficiency - Smart Meters.
46. trust, E. s. 2012. Wind Turbines.
47. Twidell, J. & A. D. Weir. 2006. Renewable energy resources.
48. Unions, I. C. O. T. 2007. Congress briefing paper no.9, towards a sustainable energy
future for Ireland. 20.
49. Wind-Energy. 2012. Wind Atlases, Onshore.
50. WindScout. 2012. What makes a good site.
51. Wineur. 2005. Wind energy integration in the urban environment. In Urban Wind
Turbines.