1. Ethan Miller
1515 Rebecca Bailey Drive, Apt. 1310A
Charlotte, NC, 28262
Cell (919) 723-8744
echevyman4wvu@gmail.com
Objective
Seeking an engineering internship position in the Electrical Engineering field, specifically in the area of
electronics.
Education
Bachelor of Science in Electrical Engineering expected May 2016
Minor: Mathematics
University of North Carolina at Charlotte, Charlotte, NC
Major GPA: 3.25/4.0
Bachelor of Science in Physics expected May 2016
University of North Carolina at Charlotte, Charlotte, NC
Major GPA: 3.0/4.0
Relevant Experience
Pulse Width Modulation Generator
 555 timer IC (NE555) in monostable operation was design to achieve a supply voltage from 0 to 5
volts and a PWM signal achieving a nominal of .4
IEEE Student Chapter
 Raspberry Pi weather balloon was sent up to achieve an altitude of 100,000 feet above UNCC
BJT/Mosfet Amplifier
 Single and Multistage amplifier was design to achieve a specific criteria of the following
symmetrical swing, gain, power consumption, input and output resistance, low and high cut-off
frequencies and a feedback for control
 LM741 op-amp of BJT,CMOS/Bi-CMOS and a VLSI design was achieve with a specific criteria
utilizing OrCad Netlist
Computer Control Modules
 Texas Instruments MSP430 Launch pad microcontroller was design to achieve the Imperial March
melody on a program called code composer studio
Power System Distribution Design
 Power System Distribution was design utilizing ETAP to achieve a specific criteria of the following
medium and low voltage percentage, a design margin of 10%, generator operating at 100%, back up
cables and generators
Audio Power/Stereo System
 Audio Power/Stereo System was design utilizing Pspice/OrCAD to achieve ± 20db for the treble
and bass gains with 30Hz as our bass cut-off and 10Hz as our treble cut-off frequencies. An iPod and
a microphone was our input to a speaker at the output. The stereo system was able to change the
volume, bass and treble signals that were coming out of the speaker.
Wind Generation Distribution System
 Constructing, testing and modeling a Wind Generation System in the AREVA Lab by utilizing
ETAP with compared measured values and simulation within 5%.

2. Academic Experience and Technical Skills
Software: MS office, Basic MS Visio, Basic MS project, Multism, Pspice (Cadence), Matlab, Netbeans,
Basic ETAP (Power System), Basic Code Composer Studio, Mathcad
Programming Languages: C++
Lab experience: Microelectronics clean room, AREVA Power Systems Room at UNCC,
Instrumentation and Networks, Logic and Networks, System and Electronics
Courses in Progress: Introduction to Electromagnetic Fields
Courses taken to date: Applied Engineering Mathematics, Classical Mechanics, System Analysis 2,
Linear Integrated Circuits, Analog and Digital Communications and Electrical Engineering Design 2
Present Projects: Linear Integrated Electronics (OP-Amp of BJT and CMOS/Bi-CMOS)
Work Experience
Providence Country Club August 2011-August 2013
 Tennis court maintenance - brush clay courts with mobile equipment, maintenance repair of
electrical light wiring, clean two- steps, manage water sprinkler system, clean and square away
tennis pro shop
 Manage tournaments and regular play - Greet members, provide customer service, clean club
house
Chapel Ridge Golf Course Summer 2007-Summer 2009
 Golf cart maintenance - charge batteries, check and change tires, clean golf carts, supply carts
with sand bottles
 Driving range attendant - keep players behind driving range line, supply soap/water/towels to
club cleaner, pick up empty ball baskets, fill divots with sand, drive range picker and pick up
range balls
 Manage tournaments and regular play - Greet members, load player’s golf bags on carts, provide
customer service, clean club house
Affiliations
St. Thomas More Catholic Church
Institute of Electrical and Electronic Engineers, (IEEE), UNCC, Student Chapter Fall 2014 to present
Institute of Electrical and Electronic Engineers Communications Society, Jan. 01, 2014 to present
Public Relations
Kramden Institute Volunteer
 Refurbish computers, rebuilt internal components including video and graphics card
Marshal at Pinehurst Golf Course - Jimmy V Cancer Foundation
 Greet members, load player’s golf bags on carts, provided customer service, managed golf
course play
Adopt- A-Highway
 Picked up trash with church community
Toys for Tots Project
 Collected toys and distributed them to the needy during Christmas with the community church
Bell ringer at designated stores
 Raised money for the poor during Christmas for the church
Thrift store
 Volunteered to help out with the band and church community
 Provided costumer service, sorted clothes, cleaned shopping area, greet costumers