This document provides instructions for disassembling the power shift transmission of a 924G and 924Gz wheel loader. It outlines 59 steps to fully disassemble the transmission, including removing the top case, torque converter, gears, bearings, seals, and individual clutch groups like the forward low and high clutches. Various tools are required to compress springs and remove components in a precise sequence while taking note of part orders and orientations. The goal is a complete teardown of the transmission into its core components and subassemblies for repair or replacement.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAB) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the power shift transmission on 924G and 924Gz wheel loaders. It outlines 71 steps to fully disassemble the transmission, including removing individual components like gears, shafts, seals, bearings, and clutch groups. Precision tools are required and notes emphasize cleanliness during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAB) Service Repair Manua...9fikslkddmd8u
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and other internal transmission parts. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized during the disassembly process to prevent dirt from entering the transmission.
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and plates/discs. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized throughout the disassembly process.
This service repair manual provides instructions for disassembling the power shift transmission of 924G and 924Gz wheel loaders. The disassembly procedure involves 71 steps to remove components like the torque converter, clutch groups, gears, shafts, seals, and bearings. Various tools are required, and cleanliness is important to prevent dirt from entering during reassembly. Detailed illustrations accompany each step to show how to properly disassemble the transmission.
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and plates/discs. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly.
This service repair manual provides instructions for disassembling the power shift transmission of 924G and 924Gz wheel loaders. The disassembly procedure involves 71 steps to remove components like the torque converter, clutch groups, gears, shafts, seals, and bearings. Various tools are required, and cleanliness is important to prevent dirt from entering during reassembly. Detailed illustrations accompany each step to show how components connect and disassemble.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3DZ) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the power shift transmission of a 924G and 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Special tools are required for tasks like compressing springs and pulling components. Cleanliness is emphasized throughout to prevent dirt from entering the transmission during disassembly.
This service repair manual provides instructions for disassembling the power shift transmission of a 924G or 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Pictures and exploded diagrams accompany each step to illustrate the proper procedure. Cleaning is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAB) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the power shift transmission on 924G and 924Gz wheel loaders. It outlines 71 steps to fully disassemble the transmission, including removing individual components like gears, shafts, seals, bearings, and clutch groups. Precision tools are required and notes emphasize cleanliness during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAB) Service Repair Manua...9fikslkddmd8u
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and other internal transmission parts. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized during the disassembly process to prevent dirt from entering the transmission.
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and plates/discs. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized throughout the disassembly process.
This service repair manual provides instructions for disassembling the power shift transmission of 924G and 924Gz wheel loaders. The disassembly procedure involves 71 steps to remove components like the torque converter, clutch groups, gears, shafts, seals, and bearings. Various tools are required, and cleanliness is important to prevent dirt from entering during reassembly. Detailed illustrations accompany each step to show how to properly disassemble the transmission.
The document provides disassembly instructions for the power shift transmission of 924G and 924Gz wheel loaders. It lists 57 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the torque converter, gear assemblies, clutch groups, seals, bearings, and plates/discs. Detailed illustrations accompany each step to show how to remove individual parts in the proper sequence. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly.
This service repair manual provides instructions for disassembling the power shift transmission of 924G and 924Gz wheel loaders. The disassembly procedure involves 71 steps to remove components like the torque converter, clutch groups, gears, shafts, seals, and bearings. Various tools are required, and cleanliness is important to prevent dirt from entering during reassembly. Detailed illustrations accompany each step to show how components connect and disassemble.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3DZ) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the power shift transmission of a 924G and 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Special tools are required for tasks like compressing springs and pulling components. Cleanliness is emphasized throughout to prevent dirt from entering the transmission during disassembly.
This service repair manual provides instructions for disassembling the power shift transmission of a 924G or 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Pictures and exploded diagrams accompany each step to illustrate the proper procedure. Cleaning is important during disassembly to prevent dirt from entering internal mechanisms.
This service repair manual provides instructions for disassembling the power shift transmission on Caterpillar 924G and 924Gz wheel loaders. It outlines 59 steps to fully disassemble the transmission, including removing individual gears, clutches, seals, and other components. Required tools are listed. Detailed illustrations accompany each step to show how to remove specific parts in the correct order. Cleanliness is emphasized during disassembly to prevent dirt from entering internal mechanisms.
This document provides disassembly instructions for the power shift transmission of a 924G and 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Special tools are required for tasks like compressing springs and pulling components. Cleanliness is emphasized throughout to prevent dirt from entering the transmission during disassembly.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3DZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the power shift transmission on Caterpillar 924G and 924Gz wheel loaders. The summary is as follows:
1) Place the transmission on a repair stand and remove components like the torque converter, top case, selector valve, and flex plate.
2) Remove gears, bearings, seals, and clutch groups including the forward low and high, reverse second, and first third gear clutches.
3) Clean parts and inspect them for wear during disassembly. Take note of order and numbers of plates and discs for reassembly.
This document provides disassembly instructions for the power shift transmission of Caterpillar 924G and 924Gz wheel loaders. It describes 59 steps to fully disassemble the transmission, including removing the top case, torque converter, gears, bearings, seals, and individual clutch groups like the forward low and high clutches, reverse second gear clutch, and first third gear clutch. Precautions are given to clean components thoroughly and note part orders for reassembly. Required specialty tools are listed.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanisms.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanisms.
This document provides disassembly instructions for the transmission and torque converter of a 924G or 924Gz wheel loader. It lists over 60 detailed steps for disassembling components like gears, plates, seals, bearings, and clutches. Special tools are required and safety precautions mentioned. The transmission must first be removed and cleaned before beginning disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as gears, plates, seals, bearings, hubs and clutches. Cleanliness is emphasized throughout the process to prevent dirt entry into internal mechanisms.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 steps for disassembling the various components. These include removing plates, discs, gears, seals, bearings, and other parts of the transmission and torque converter. Cleanliness is emphasized throughout the process.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 detailed steps for disassembling the various transmission components. These include removing gears, plates, seals, bearings, springs, and other parts. Cleanliness is emphasized throughout the process.
This document provides disassembly instructions for the transmission and torque converter of a 924G or 924Gz wheel loader. It lists over 60 detailed steps for disassembling components like gears, plates, seals, bearings, and clutches. Special tools are required and safety precautions mentioned. The transmission must first be removed and cleaned before beginning disassembly.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt contamination of parts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RBB) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 detailed steps for disassembling the various transmission components. These include removing gears, plates, seals, bearings, and clutch groups. Cleanliness is emphasized throughout and components are marked for installation reference.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, springs, and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as gears, plates, seals, bearings, and clutches. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions to remove components such as gears, seals, plates, discs, bearings, and clutches. Safety precautions are provided for releasing clutch springs. The disassembly process is described in detail through 50 steps and accompanied by illustrations of each step.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RBB) Service Repair Manua...9fikslkddmd8u
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as clutches, gears, seals, plates, and discs. Cleanliness is emphasized throughout the process to prevent dirt entry.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RTA) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists 50 steps to completely disassemble the transmission, removing components like gears, plates, seals, bearings, and clutch groups. Special tools are required for tasks like compressing clutch springs and removing certain parts. Cleanliness is emphasized throughout to prevent dirt from contaminating internal parts.
This document provides disassembly instructions for a transmission and torque converter for wheel loader models 924G and 924Gz. It lists the required tools and presents a step-by-step process to disassemble the transmission, torque converter, and various clutch groups within the transmission. The disassembly involves removing bolts, seals, gears, plates, discs, bearings, springs, and other internal components. Cleanliness during disassembly is emphasized.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
More Related Content
Similar to Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 9SW) Service Repair Manual Instant Download.pdf
This service repair manual provides instructions for disassembling the power shift transmission on Caterpillar 924G and 924Gz wheel loaders. It outlines 59 steps to fully disassemble the transmission, including removing individual gears, clutches, seals, and other components. Required tools are listed. Detailed illustrations accompany each step to show how to remove specific parts in the correct order. Cleanliness is emphasized during disassembly to prevent dirt from entering internal mechanisms.
This document provides disassembly instructions for the power shift transmission of a 924G and 924Gz wheel loader. It lists 70 steps to fully disassemble the transmission, removing components like gears, clutches, seals, bearings and shafts. Special tools are required for tasks like compressing springs and pulling components. Cleanliness is emphasized throughout to prevent dirt from entering the transmission during disassembly.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3DZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the power shift transmission on Caterpillar 924G and 924Gz wheel loaders. The summary is as follows:
1) Place the transmission on a repair stand and remove components like the torque converter, top case, selector valve, and flex plate.
2) Remove gears, bearings, seals, and clutch groups including the forward low and high, reverse second, and first third gear clutches.
3) Clean parts and inspect them for wear during disassembly. Take note of order and numbers of plates and discs for reassembly.
This document provides disassembly instructions for the power shift transmission of Caterpillar 924G and 924Gz wheel loaders. It describes 59 steps to fully disassemble the transmission, including removing the top case, torque converter, gears, bearings, seals, and individual clutch groups like the forward low and high clutches, reverse second gear clutch, and first third gear clutch. Precautions are given to clean components thoroughly and note part orders for reassembly. Required specialty tools are listed.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanisms.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanisms.
This document provides disassembly instructions for the transmission and torque converter of a 924G or 924Gz wheel loader. It lists over 60 detailed steps for disassembling components like gears, plates, seals, bearings, and clutches. Special tools are required and safety precautions mentioned. The transmission must first be removed and cleaned before beginning disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as gears, plates, seals, bearings, hubs and clutches. Cleanliness is emphasized throughout the process to prevent dirt entry into internal mechanisms.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 steps for disassembling the various components. These include removing plates, discs, gears, seals, bearings, and other parts of the transmission and torque converter. Cleanliness is emphasized throughout the process.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 detailed steps for disassembling the various transmission components. These include removing gears, plates, seals, bearings, springs, and other parts. Cleanliness is emphasized throughout the process.
This document provides disassembly instructions for the transmission and torque converter of a 924G or 924Gz wheel loader. It lists over 60 detailed steps for disassembling components like gears, plates, seals, bearings, and clutches. Special tools are required and safety precautions mentioned. The transmission must first be removed and cleaned before beginning disassembly.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt contamination of parts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RBB) Service Repair Manua...9fiisekodkdmd
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents 53 detailed steps for disassembling the various transmission components. These include removing gears, plates, seals, bearings, and clutch groups. Cleanliness is emphasized throughout and components are marked for installation reference.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, springs, and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as gears, plates, seals, bearings, and clutches. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions to remove components such as gears, seals, plates, discs, bearings, and clutches. Safety precautions are provided for releasing clutch springs. The disassembly process is described in detail through 50 steps and accompanied by illustrations of each step.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RBB) Service Repair Manua...9fikslkddmd8u
This document provides disassembly instructions for the transmission and torque converter of a 924G/924Gz wheel loader. It lists the required tools and presents over 60 steps for disassembling components such as clutches, gears, seals, plates, and discs. Cleanliness is emphasized throughout the process to prevent dirt entry.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RTA) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists 50 steps to completely disassemble the transmission, removing components like gears, plates, seals, bearings, and clutch groups. Special tools are required for tasks like compressing clutch springs and removing certain parts. Cleanliness is emphasized throughout to prevent dirt from contaminating internal parts.
This document provides disassembly instructions for a transmission and torque converter for wheel loader models 924G and 924Gz. It lists the required tools and presents a step-by-step process to disassemble the transmission, torque converter, and various clutch groups within the transmission. The disassembly involves removing bolts, seals, gears, plates, discs, bearings, springs, and other internal components. Cleanliness during disassembly is emphasized.
Similar to Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 9SW) Service Repair Manual Instant Download.pdf (20)
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
This document provides instructions for removing and installing the camshaft on a Caterpillar 3412C engine. Key steps include:
1. Removing the front housing, lifter group, and flywheel housing.
2. Removing four bolts and a plate from the rear of the camshaft and removing the camshaft gear.
3. Aligning timing marks and removing two bolts and a plate from the camshaft.
4. Removing the camshaft from the cylinder block and optionally removing the camshaft gear using a driver group tool.
This service repair manual provides instructions for removing and installing the flywheel housing and rear power take-off (RPTO) on a Caterpillar 657G wheel tractor. The flywheel housing removal procedure involves removing bolts and seals, then lifting the housing off using lifting brackets. Installation involves cleaning parts, applying sealant, positioning seals and gaskets, and tightening bolts in a specific sequence. The RPTO removal procedure describes removing gears, idlers, retainers, sleeves and covers. Installation involves cleaning, lubricating, and positioning these parts before securing with bolts.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing O-rings, bolts, bearings, and shaft components.
This document provides instructions for installing a crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes cleaning and applying retaining compound to the crankshaft and wear sleeve. A locator is installed on the crankshaft to position the wear sleeve and seal, which are then installed using an installer tool. Finally, the installer is removed and bolts are tightened to complete the installation.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including gears, shafts, bearings, and seals. The assembly process describes installing these components in 23 steps, noting proper orientation and torque specifications. Tools required include various pullers, presses, and forcing screws.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hydraulic and electrical connections, draining fluid from the elbow, attaching a lifting device to the pump, and removing mounting nuts and the pump. Cleaning parts and plugging lines is noted for prevent contamination during removal.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Removing the flywheel by using bolting brackets to hold the crankshaft gear, installing guide bolts, and lifting the flywheel off with a hoist.
- Reinstalling components by pressing bearings into place with drives, torquing bolts, and checking runout after installing the flywheel.
The document provides detailed step-by-step instructions accompanied by illustrations of the disassembly and
This document provides instructions for installing and removing the crankshaft rear seal on a Caterpillar 657E wheel scraper. The removal procedure involves using a punch or slide hammer puller to puncture and remove the existing seal. The installation procedure specifies using a seal installer tool and retaining compound to press the new seal and wear sleeve onto the crankshaft. Precautions are given to keep the components clean and not reuse a separated seal and sleeve. The instructions are illustrated with diagrams and apply to both engine configurations with and without a rear gear train.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 651E wheel scraper. The removal procedure involves using various tools to disassemble the adapter assemblies, gears, bearings and other components. The installation procedure describes cleaning and lubricating parts, pressing or installing bearings and gears back into place, and reassembling the components in reverse order. Precautions are given to keep parts clean and lubricated to prevent wear.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including the housing assembly, torque converter assembly, impeller wheel assembly, carrier assembly, and stator assembly. It then describes assembling the torque converter in 25 steps by installing the parts in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and slide hammers.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...9fikslkddmd8u
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...9fikslkddmd8u
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing components like the camshaft gear and rocker arms first. Tools like a cradle, guide, camshaft pilots and hooks are then used to support the camshaft as it is moved out of the cylinder head and into the guide. Care must be taken to avoid damaging the camshaft or bearings during removal.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order, noting to keep parts clean and apply Loctite to the threaded rod.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER 9SW
Configuration: 924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
924G and 924GZ Wheel Loaders Power Train
Media Number -RENR3506-05 Publication Date -01/05/2004 Date Updated -09/10/2017
i01738796
Power Shift Transmission - Disassemble
SMCS - 3030-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 1U-9759 Jack Stand 1
C 6V-2156 Link Bracket 2
D 4C-6136 Lifting Bracket 1
E 4C-6399 Spring Compressor 1
F FT-2343 Plexiglass Cover 1
G 1P-2321 Puller 1
H 4C-3652 Spring Compressor 1
Start By:
a. Separate the engine, and the transmission. Refer to Disassembly and Assembly, RENR3503,
"Engine from Torque Converter and Transmission - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00653680
1. Use Tooling (C) and a suitable lifting device in order to place the transmission on Tooling
(A) and (B), as shown. The weight of the transmission is approximately 500 kg (1100 lb).
2. Remove torque converter (1).
3. Remove bolts (2) and the top transmission case. The weight of the top transmission case is
approximately 163 kg (360 lb).
Note: Remove the selector and pressure control valve. Install Tooling (F). Refer to
Disassembly and Assembly, "Selector And Pressure Control Valve (Transmission)- Remove
And Install".
Illustration 2 g00671890
4. Remove bolts (3) and flex plate (4) from torque converter (1).
2/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00653775
5. Remove bolts (5) and plate (6).
Illustration 4 g00653801
6. Remove lip type seal (7) and seal (8).
Illustration 5 g00653806
7. Remove bolts (9).
3/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00653858
12. Using Tooling (D) to remove the forward low and the forward high clutch group (15). The
weight of the clutch group is approximately 27 kg (60 lb).
Note: When the clutch groups are disassembled, remove the shaft plugs (16) in order to
clean the oil passages. Use a punch to drive the plug into the shaft . Drill the remainder of
the aluminum plug out of the bore. Be careful not to drill any portion of the walls of the
bore. Use shop air or a cleaning solution in order to clean the shafts.
Illustration 10 g00653893
13. Remove ring (17) and washer (18).
5/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00653932
14. Remove ring (19).
15. Use a suitable press in order to remove gear (20).
Illustration 12 g00890607
16. Remove ring (22). Remove hub (21). Remove plates and discs (23).
Note: Take note of the number and order of plates and discs for assembly purposes.
Illustration 13 g00653959
17. Remove washer (24).
Note: The retainer may stick to the inside of hub (22) when the hub is removed.
6/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00890608
18. Remove ring (26). Press bearing (25) from hub (22).
Illustration 15 g00654018
19. Put the forward low clutch group in a press. Use Tooling (H) in order to compress the
spring. Remove ring (27).
Illustration 16 g00654029
20. Remove retainer (28) and spring (29).
7/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00890609
21. Release piston (32) by blowing shop air into lube passage (31). Remove piston (32).
22. Remove seals (30).
Illustration 18 g00654063
23. Remove seals (33).
Illustration 19 g00654078
24. Disassemble the forward high clutch group by removing ring (34). Remove washer (35).
8/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00654253
25. Remove ring (36). Remove gear (37).
Illustration 21 g00654261
26. Remove hub (38).
Illustration 22 g00654263
27. Remove ring (39). Use a suitable press in order to remove bearing (40).
9/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00654274
28. Remove washer (41). Remove ring (42). Remove the plate and discs (43).
Note: Take note of the number and order of plates and discs for assembly purposes.
Illustration 24 g00654276
29. Put the forward high clutch group in a suitable press. Use Tooling (H) in order to remove
ring (44).
Illustration 25 g00654280
10/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 26 g00654282
30. Remove retainer (45) and spring (46).
31. Blow shop air into lube passage (48) in order to remove piston (47).
Illustration 27 g00654292
32. Remove seals (49) and (50).
Illustration 28 g00654301
33. Use Tooling (D) in order to remove reverse second gear clutch group (51). The weight of
the clutch group is approximately 32 kg (70 lb).
11/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 29 g00654339
34. Remove ring (52) and washer (53).
Illustration 30 g00654328
35. Remove ring (54) and gear (55).
Illustration 31 g00654347
36. Remove hub assembly (56).
12/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 32 g00890610
37. Remove washer (58).
38. Remove ring (57). Remove plates and discs (59).
Note: Take note of the number and order of the plates and discs for assembly purposes.
Illustration 33 g00890611
39. Remove ring (60). Use a suitable press in order to remove bearing (61).
Illustration 34 g00654360
13/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 40. Put the reverse clutch group in a suitable press. Use Tooling (H) in order to remove ring
(62).
Illustration 35 g00654364
41. Remove retainer (63) and spring (64).
Illustration 36 g00654372
Illustration 37 g00654378
42. Release piston (65) by blowing shop air into lube passage (66). Remove piston (65).
43. Remove seals (67).
14/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 38 g00654403
44. Remove seals (68) and (69).
Illustration 39 g00890612
45. Install a suitable puller under gear (72). Pull gear (72), spacer (70), and bearing (71).
46. Remove spacer (73). Remove washer (74) and (75).
Note: Use Steps 35 through 44 for the remaining disassembly of the second gear clutch
group. In Step 40, use Tooling (E) instead of Tooling (H).
15/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 40 g00654494
47. Use Tooling (D) in order to remove first third gear clutch group (76). The weight of the
clutch group is approximately 50 kg (110 lb).
Illustration 41 g00654497
48. Remove ring (77) and washer (78).
Illustration 42 g00654507
49. Remove ring (79) and gear (80).
Illustration 43 g00654512
16/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 50. Remove hub assembly (81).
Illustration 44 g00890613
51. Remove ring (82). Use a suitable press in order to remove bearing (83).
Illustration 45 g00654519
52. Remove washer (84).
53. Remove ring (85). Remove plates and discs (86).
Note: Take note of the number and order of the plates and discs for assembly purposes.
17/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 46 g00654525
54. Put the third gear clutch group in a suitable press. Use Tooling (H) in order to remove ring
(87).
Illustration 47 g00654534
55. Remove retainer (88) and spring (89).
Illustration 48 g00890615
56. Release piston (90) by blowing shop air into lube passage (91). Remove piston (90).
57. Remove seals (92).
18/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 49 g00654638
58. Remove seals (93) and (94).
Illustration 50 g00890617
59. Disassemble the first gear clutch by installing Tooling (G) through the holes in gear (95).
Pull gear (95), washer (96), and bearing (97) together.
Illustration 51 g00654719
60. Remove washer (98). Remove ring (99) and gear (100).
Illustration 52 g00654724
19/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 61. Remove hub assembly (101).
Illustration 53 g00890619
62. Remove washers (102) and (104). Remove ring (103). Remove plates and discs (105).
Note: Take note of the number and order of the plates and discs for assembly purposes.
Illustration 54 g00654818
63. Remove ring (106).
Illustration 55 g00654824
20/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 64. Remove bearing assembly (107).
Illustration 56 g00654833
65. Put the clutch group in a suitable press. Use Tooling (H) in order to remove ring (108).
Illustration 57 g00654837
66. Remove the retainer and seal assembly (109).
Illustration 58 g00654842
67. Remove spring (110).
21/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 59 g00654966
68. Remove piston (111). Blow shop air into the lube passage in order to release the piston.
Illustration 60 g00654969
69. Remove seals (112), (113), and (114).
Illustration 61 g00655016
70. Remove input shaft assembly (115).
22/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 62 g00890621
71. Remove carrier (117) and seal (116). Remove bearing (121) and gear (120).
72. Remove bearing (118) and gear (119).
Illustration 63 g00655110
73. Remove bearing (122) and bearing cups (123).
Illustration 64 g00655120
74. Remove bolt (124), washer (125), and yoke (126).
23/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 65 g00685060
75. Remove the bolt and washer (127).
Illustration 66 g00890622
76. Remove seal (128). Remove yoke (129) and brake drum (130) together.
Illustration 67 g00890758
77. Remove bolts (131). Remove plate (132).
78. Remove parking brake assembly (133), and lever (134).
24/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 68 g00655180
79. Remove bolts (135).
Illustration 69 g00655189
80. Install bolts (136). Tighten bolts (136) in order to remove cage (137).
Illustration 70 g00655206
81. Remove shims (138).
25/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 71 g00890759
82. Remove seal (139). Remove bearing cup (140) and lip seal (141).
Illustration 72 g00890760
83. Remove nuts (142) and cover (143).
Illustration 73 g00655439
84. Remove the output shaft and gear (144).
26/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 74 g00890761
85. Remove bolts (145) and shield assembly (147).
86. Remove bearing cup (146) and lip seal (148).
Illustration 75 g00655464
87. Remove bearing (149) from the output shaft.
Illustration 76 g00655451
88. Remove bearing (150). Remove ring (151) and gear (152).
27/28
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 30...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER 9SW
Configuration: 924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
924G and 924GZ Wheel Loaders Power Train
Media Number -RENR3506-05 Publication Date -01/05/2004 Date Updated -09/10/2017
i02055589
Power Shift Transmission - Assemble
SMCS - 3030-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 1U-9759 Jack Stand 1
C 6V-2156 Link Bracket 2
D 4C-6136 Lifting Bracket 1
E 4C-6399 Spring Compressor 1
F FT-2343 Plexiglass Cover 1
G 4C-6143 Clutch Piston Installer 1
H 4C-3652 Spring Compressor 1
J
4C-6137 Bearing Installer 1
4C-6142 Spacer 1
1P-531 Handle 1
K 4C-6402 Plug Installer 1
L 5P-3413 Pipe Sealant 1
M 9S-3263 Thread Lock Compound 1
N 1U-8846 Gasket Sealant 1
1/29
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g00655451
1. Install gear (152) and ring (151). Heat bearing (150) to a temperature of 135 °C (275 °F).
Install bearing (150).
Illustration 2 g00655464
2. Heat bearing (149) to a temperature of 135 °C (275 °F). Install bearing (149).
2/29
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 3 g00890761
3. ApplyTooling (L) to the seal bore.
4. Install lip seal (148). Lubricate the sealing lip with the lubricant that is being used.
5. Lower the temperature of bearing cup (146). Install bearing cup (146).
6. Use bolts (145) in order to install shield assembly (147). The torque for bolts (145) is
55 ± 10 N·m (40 ± 10 lb ft).
Illustration 4 g00655439
7. Install the output shaft and gear (144).
Illustration 5 g00890760
8. Use nuts (142) in order to install cover (143). The torque for nuts (142) is 9 ± 1 N·m
(6 ± 1 lb ft).
3/29
924G and 924Gz Wheel Loader 9SW00001-02428 (MACHINE) POWERED BY 3056...
2021/1/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...